ASDM Unable to read config

Hello,
I have a PIX 515e.
When I load the ASDM Software on my pc I receive the error " ASDM us unable to read the configuration from the PIX. Please check the configuration and your connection and then try again by licking the refresh button."
I can get into the pix via putty and no config changes have been made in months. Whenever I click refresh I get the same error.
Any ideas?
Thanks in Advance

We had the same problem after updating the Sun Java client to v6 update 11. Just downgrade and you should be ok again.
The same issue is with adsm on ASA.

Similar Messages

Usb 1-7: unable to read config index 0 descriptor/start -71

On my laptop (Asus N550LF) this message appears repeatedly during boot. Once X is running it seems to stop, although it could just be that I cant see the output!
There are few posts for usb 1-7: unable to read config index 0 descriptor/start -71 but they all seem to suggest it's a USB device. This happens whether or not I have anything plugged into USB.
Is there anything I can do to debug this further?

May or may not be helpful:
https://bbs.archlinux.org/viewtopic.php … 5#p1050195 and https://bbs.archlinux.org/viewtopic.php?id=134726
https://bbs.archlinux.org/viewtopic.php … 3#p1121923 [note that this concerns an installed system and is from before Arch's switch to systemd]
Do you have settings in BIOS affecting support for USB? E.g. sometimes there are options to enable/disable support for different ways of accessing stuff or different versions of stuff.

ASDM is unable to read the configuration from ASA.

Earlier today I was configuring the Cisco ASA (7.2(2)) using the ASDM, but after a reboot of the appliance I now get the following:
ASDM is unable to read the configuration from ASA.
This happens shortly after ?Loading running configuration from the device? appears in the ASDM status window.
I have tried restarting both the appliance and my workstation, but the issue persists. I have also tried clearing the ASDM cache, but that doesn?t help either. The issue occurs whether I used the Cisco ASDM Launcher or the web interface.
SSH access to the appliance works fine.
Thanks for any assistance (why is it that Cisco?s GUIs always have issues?!?).

I have exactly the same issue , SSH works fine but ASDM and Web interface reply with that error message "ASDM is unable to read the configuration from ASA".
My ASA is a 5520 ver 7.1(2) with ASDM 5.1(2)
Could it be something related to Java ?
Thanks for any hint.

"Unable to open config file" Error when starting tomcat

hi all,
Here is the output from two of the log files when I start tomcat4 on my linux box. I have configured the mod_jk on the tomcat side.
From the output of the second log file, it seems that the ajp13 worker I defined was started successfully. What I don't understand is the following:
1) In catalina.out, where des the line 'Unable to open config file' come from? Which config file?
2) Tomcat4 is supposed to generate a mod_jk.conf automatically, but I don't see any file generated in 'conf/auto/'.
Content of 'catalina.out'
Unable to open config file
Starting service Tomcat-Standalone
Apache Tomcat/4.0.4
Unable to open config file
Starting service Tomcat-Apache
Apache Tomcat/4.0.4content of 'catalina_log.2002-08-16.txt'
2002-08-16 01:05:22 HttpConnector Opening server socket on all host IP addresses
2002-08-16 01:05:28 Ajp13Connector[8009] Opening server socket on all host IP addresses
2002-08-16 01:05:28 Ajp13Connector[8009] Starting background thread
2002-08-16 01:05:29 Ajp13Processor[8009][0] Starting background thread
2002-08-16 01:05:29 Ajp13Processor[8009][1] Starting background thread
2002-08-16 01:05:29 Ajp13Processor[8009][2] Starting background thread
2002-08-16 01:05:29 Ajp13Processor[8009][3] Starting background thread
2002-08-16 01:05:29 Ajp13Processor[8009][4] Starting background thread

I have all those files too.
I think the 'config file' mentioned in the error log is the mod_jk.conf.
On Jason Hunter's tomcat4 guide, it says don't use the tomcat4 RPM to installed. What is the difference bettween the RPM version and the tar.gz version? The only difference I can think of is that in the RPM version, the conf directory is in the 'etc/tomcat4/conf'. Could it be the reason that tomcat4 cannot read the config file? But it has no problem reading the server.xml though.

Unable to read payload from the message object in XI

Hello Guys,
Please help me about my problem in XI version 7.0.im quite new here.
im trying to test my config but error message occured. "Unable to read payload from the message object"
when i checked the comm channel this is the error message :
Error during database connection to the database URL 'jdbc:sqlserver://172.16.40.20:1433;databasename=TRAVEL:SelectMethod=cursor' using the JDBC driver 'com.microsoft.sqlserver.jdbc.SQLServerDriver': 'com.sap.aii.adapter.jdbc.sql.DriverManagerException: Cannot establish connection to URL 'jdbc:sqlserver://172.16.40.20:1433;databasename=TRAVEL:SelectMethod=cursor': com.microsoft.sqlserver.jdbc.SQLServerException: Cannot open database "TRAVEL:SelectMethod=cursor" requested by the login. The login failed.'
when i tried my login in sql it works...but in this message the login is failed..what shall i do..
Please advice.
Thanks in advance
aVaDuDz

Hi
Check with the connection string & Authorization of user you have used.
MSSQL string is
jdbc:microsoft:sqlserver://dbhost:1433;databaseName=example;SelectMethod=Cursor
While doing JDBC its good to refer Note 831162 lot of problems can be resolved.
Thanks
Gaurav

Oblix_OBWebGate_AuthnAndAuthz: ..- Unable to read log configuration file.

Hi All,
I have a painful problem with Oracle 10g Webgate. I am using Oracle_Access_Manager10_1_4_3_0_linux64_APACHE22_WebGate to procted Apache resource. I have some problem in Custom Authentication plugin. which is not still resolve(https://forums.oracle.com/thread/2549716).
Now I have apply patch BP9 (Oracle_Access_Manager10_1_4_3_0_BP09_Patch_linux64_APACHE22_WebGate) for Webgate, Now I have a new issue, I am unable to get the logon page of OAM when I try to access my Apache resource.
The Error Message in the browser is:
Internal Server Error
The server encountered an internal error or misconfiguration and was unable to complete your request.
Please contact the server administrator, root@localhost and inform them of the time the error occurred, and anything you might have done that may have caused the error.
More information about this error may be available in the server error log.
Apache/2.2.3 (Oracle) Server at apache.tigerit.com Port 80
In the error log file of Apache I have found
[Sun Jun 23 11:53:17 2013] [error] [client 192.168.1.156] Oblix_OBWebGate_AuthnAndAuthz: Error: /opt/netpoint/webgate/access/oblix/config/oblog_config_wg.xml - Unable to read log configuration file.
[Sun Jun 23 11:53:17 2013] [error] [client 192.168.1.156] Oblix_OBWebGate_AuthnAndAuthz: Error: /opt/netpoint/webgate/access/oblix/config/oblog_config_wg.xml - Unable to read log configuration file.
[Sun Jun 23 11:53:20 2013] [error] [client 192.168.1.156] Oblix_OBWebGate_AuthnAndAuthz: Error: /opt/netpoint/webgate/access/oblix/config/oblog_config_wg.xml - Unable to read log configuration file.
[Sun Jun 23 11:53:35 2013] [error] [client 192.168.1.156] Oblix_OBWebGate_AuthnAndAuthz: Error: /opt/netpoint/webgate/access/oblix/config/oblog_config_wg.xml - Unable to read log configuration file.
[Sun Jun 23 11:53:35 2013] [error] [client 192.168.1.156] Oblix_OBWebGate_AuthnAndAuthz: Error: /opt/netpoint/webgate/access/oblix/config/oblog_config_wg.xml - Unable to read log configuration file.
[Sun Jun 23 11:53:35 2013] [error] [client 192.168.1.156] Oblix_OBWebGate_AuthnAndAuthz: Error: /opt/netpoint/webgate/access/oblix/config/oblog_config_wg.xml - Unable to read log configuration file.
Can Anyone help me regarding this issue...
Thanks
Tamim Khan

Hi Colin,
Thanks for your help, You are right I have change the permission of /opt/netpoint/webgate/access/oblix/lib/libxmlengine.so.
Now I am able to access the logon page of the access manager.
But the problem as I mention in (https://forums.oracle.com/thread/2549716) my ObSSOCookie value is still loggedcontinue.
My Authentication return (ExecutionStatus.SUCCESS) Successful from the Java Code , and I am unable to login in the application. The thing is I can't manipulate ObSSOCookie from Java code.
I have apply Patch 12363955 to resolve this issue. But this patch is now to resolve this issue.
Have you any idea how to resolve this issue.
Thanks
Tamim Khan

Unable to read SEARCH response from backend server

Currently we have problem when searching huge amounts of users against new SunOne Directory Server v6.3
in production and acceptance.
[17:12:43] root@ecdiala03-2[!]# /opt/app/sun/ds6/bin/dsadm -V
[dsadm]
dsadm : 6.3 B2008.0311.0058 NAT
[slapd 64-bit]
Sun Microsystems, Inc.
Sun-Java(tm)-System-Directory/6.3 B2008.0311.0058 64-bit
ns-slapd : 6.3 B2008.0311.0058 NAT
Slapd Library : 6.3 B2008.0311.0058
Front-End Library : 6.3_MTR_5087249_1_20081209 B2008.1210.1821
==============================================================
Its not working while searching huge amounts of users against DPS.However, Its working while searching huge amounts of users against DS.
Below is the error from access log of DPS when the problem occurred.
==================================
31/Mar/2009:14:08:17 +0200] - CONNECT - INFO - conn=4565433 client=153.88.247.15:2719 server=ecdiala03-1:389 protocol=LDAP
[31/Mar/2009:14:08:17 +0200] - PROFILE - INFO - conn=4565433 assigned to connection handler cn=default connection handler, cn=connection handlers, cn=config
[31/Mar/2009:14:08:17 +0200] - OPERATION - INFO - conn=4565433 op=0 BIND dn="uid=itimadm1,ou=system accounts,o=ericsson" method="SIMPLE" version=3
[31/Mar/2009:14:08:17 +0200] - SERVER_OP - INFO - conn=4565433 op=0 BIND dn="uid=ITIMADM1,ou=system accounts,o=Ericsson" method="SIMPLE"" version=3 s_msgid=17 s_conn=ecditna03-2:72725
[31/Mar/2009:14:08:17 +0200] - SERVER_OP - INFO - conn=4565433 op=0 BIND RESPONSE err=0 msg="" s_conn=ecditna03-2:72725
[31/Mar/2009:14:08:17 +0200] - PROFILE - INFO - conn=4565433 assigned to connection handler cn=BindDone,cn=connection handlers,cn=config
[31/Mar/2009:14:08:17 +0200] - OPERATION - INFO - conn=4565433 op=0 BIND RESPONSE err=0 msg="" etime=0
[31/Mar/2009:14:08:17 +0200] - OPERATION - INFO - conn=4565433 op=1 msgid=2 SEARCH base="ou=External,o=Ericsson" scope=2 filter="(objectclass=inetorgperson)" attrs="*"
[31/Mar/2009:14:08:17 +0200] - SERVER_OP - INFO - conn=4565433 op=1 SEARCH base="ou=external,o=ericsson" scope=2 filter="(objectclass=inetorgperson)" attrs="*" s_msgid=18 s_conn=ecditna03-2:72725
[31/Mar/2009:14:12:25 +0200] - OPERATION - INFO - conn=4565433 op=1 SEARCH RESPONSE err=1 msg="Unable to read SEARCH response from backend server : Timeout when waiting to read from input stream" nentries=33959 etime=248309
[31/Mar/2009:14:17:25 +0200] - DISCONNECT - INFO - conn=4565433 reason="other" msg="Exception caught while polling client connection LDAP.153.88.247.15.2719 -- java.io.IOException: Connection reset by peer"
================================
>>
> > [15:12:29] root@ecdiala03-1[!]# ./dpadm -V
> >
> > [dpadm]
> >
> > dpadm :
> >
6.3_PD_COMBO_CUMULATIVE_VIRTUAL_15112008_ED2.0+6774589+6780423+6778308+6782659_2
> > B2008.1212.0459 NAT
> >
> >
> >
> > [DPS]
> >
> > Sun Microsystems, Inc.
> >
> >
Sun-Java(tm)-System-Directory-Proxy-Server/6.3_PD_COMBO_CUMULATIVE_VIRTUAL_15112008_ED2.0+6774589+6780423+6778308+6782659_2
> > B2008.1212.0436
> >
> > =================

We have changed the value of data-source-read-timeout in DPS from 20s to 30m.As per application test, the "time out" error has gone, but we get a new error as following.
==========================
[27/Apr/2009:05:28:36 +0200] - SERVER_OP - INFO - conn=209469 op=8 SEARCH base="ou=internal,o=ericsson" scope=2 filter="(objectclass=ericssonInternal)" attrs="EriCA-AttesterNL EriCA-EmploymentForm EriCA-KeyRecoveryNL-Auth EriCA-NL-Auth EriCA-NLOTP-Admin EriCA-NLOTP-User EriCA-accountExpires c cn departmentNumber description displayName eriCompanySynch eriCountry eriCountryCode eriEmployeeStatus eriExpired eriIsManager eriMasterDomain eriOpOrgUnitAbbreviation eriOpOrgUnitIdentifier eriOpOrgUnitName eriOperationalManager eriPartner eriPartnerTrigram eriPwSynchDate eriSignType eriSignum eriSignumStatus facsimileTelephoneNumber givenName isMemberOf l mail memberOf mobile objectClass ou sametimebrowseldap sametimehomeserver sametimeuser smChallResp smDisabled smXauthRADIUSServer sn telephoneNumber title uid uidNumber " s_msgid=27 s_conn=ecditna03-2:8645
[27/Apr/2009:06:06:23 +0200] - SERVER_OP - INFO - conn=209469 op=8 SEARCH RESPONSE err=0 msg="" nentries=236367 s_conn=ecditna03-2:8645
[27/Apr/2009:06:06:23 +0200] - OPERATION - INFO - conn=209469 op=8 SEARCH RESPONSE err=0 msg="" nentries=236367 etime=2266483
[27/Apr/2009:06:11:27 +0200] - DISCONNECT - INFO - conn=209469 reason="other" msg="Exception caught while polling client connection LDAP.153.88.247.15.4862 -- java.io.IOException: Connection reset by peer"
================
Each time while application client (153.88.247.15) connecting DPS to read, they will exit with connection reset error.
Could you please kindly give us some suggestion if this error is realted to the DPS?

NVRAM: Unable to read configuration. Try again later.

Hi,
I have built a 3750 switch stack (8 switches) and every now and then (random) when i do a "show run" or "write mem", i get the following error message
NVRAM: Unable to read configuration. Try again
It doesn't happen all the time, its a random thing. I'm currently using c3750-ipservicesk9-mz.122-53.SE2.bin.
I have checked the memory and there's a lot of free memory. I am the only person consoled onto the stack. I did reboot the stack but its an intermittent problem.
Anyone encountered this issue before?

I have noticed the same problem when working on larger 3750 and 3750X stacks on several different code levels. I applied the "DEBUG CONFIGURATION LOCK" command and was able to duplicate the problem. I shut down and unused interface and tried to write the configuration and got the messages below:
May 25 00:09:55: Parser: - Config. Lock requested by process <342> client
May 25 00:09:55: Parser: - Config. Lock acquired successfully !
May 25 00:09:55: Parser: - Config. SHARED UnLock requested
May 25 00:09:55: Parser: - Config UNLOCKED !
May 25 00:10:08: Parser: - Config. Lock requested by process <342> client
May 25 00:10:08: Parser: - Config. Lock acquired successfully !
May 25 00:10:08: Parser: - Config. SHARED UnLock requested
May 25 00:10:08: Parser: - Config UNLOCKED !wr
May 25 00:10:15: Parser: - Config. Lock requested by process <342> client
May 25 00:10:15: Parser: - Config. Lock acquired successfully !
May 25 00:10:15: Parser: - Config. SHARED UnLock requested
May 25 00:10:15: Parser: - Config UNLOCKED !end
Stack-1#wr
May 25 00:10:17: %SYS-5-CONFIG_I: Configured from console by tkazee on vty0 (10.65.128.62)
May 25 00:10:20: Exec command locking feature is not enabled.
NVRAM: Unable to read configuration. Try again later.
Stack-1#
The problem appears to be related to the "SSH Process". You are not alone.

Unable to read HTTPD_CFG_FILE

Hi,
After some unfortunate configuration changes my web server (sun one web server 6.0 sp5) doesn't start, and i get this log:
[21/Feb/2003:15:19:10] warning (16061): unable to read HTTPD_CFG_FILE: %s reports: HTTPD_CFG_FILE
[21/Feb/2003:15:19:10] warning (16061): error in reading max procs reports: -1
[21/Feb/2003:15:19:10] catastrophe (16061): Unable to create/cleanup jsp class cache
[21/Feb/2003:15:19:10] catastrophe (16061): Unable to create/cleanup persistent session data cache
[21/Feb/2003:15:19:11] failure (16062): Invalid configuration: Could not determine base pathname of the file
Can anyone tell me what is wrong. I have tested the configuration with a start -configtest and it is all right.
Thanks
Juan

It looks like some general problem with the path to the web server directory. First a plugin (Vignette?) complains, then the web container, and finally the core server.
I'm not sure what the problem is, but I'd check all the directories above the web server config directory for permission issues; on Unix, the user the web server runs as needs to have "x" access to each directory.
Please let us know if you discover the source of the problem.

Unable to read cache.

I receive an error message each time I log onto Bridge saying it is unable to read cache. I have tried purging the central cache as recommended, but still get this error message. I am operating a mac. Help????

Default is to use multicast (when multicast is not available in the network) you can define wel-known-addresses, for example,
<coherence xmlns:xsi="http://www.w3.org/2001/XMLSchema-instance" xmlns="http://xmlns.oracle.com/coherence/coherence-operational-config" xsi:schemaLocation="http://xmlns.oracle.com/coherence/coherence-operational-config coherence-operational-config.xsd">
    <cluster-config>
        <member-identity>
            <cluster-name system-property="tangosol.coherence.cluster">KlantCluster</cluster-name>
        </member-identity>
        <unicast-listener>
            <well-known-addresses>
                <socket-address id="1">
                    <address>172.31.0.175</address>
                    <port>8088</port>
                </socket-address>
                <socket-address id="2">
                    <address>172.31.0.113</address>
                    <port>8088</port>
                </socket-address>
            </well-known-addresses>
        </unicast-listener>
    </cluster-config>
</coherence>You can put this in tangosol-coherence-override.xml
http://middlewaremagic.com/weblogic/?page_id=5436

ASA: CRYPTO_PKI: Unable to read CA/RA certificates

Hello,
I have setup a Win2003 Server where I install a CA/RA server for SCEP enrollment of my ASA5510. I entered the following config on the ASA:
domain-name mydomain.com
crypto key generate rsa
crypto ca trustpoint MYTRUSTPOINT
crl optional
enrollment url http://x.x.x.x/certsrv/mscep/mscep.dll
subject-name cn=ASA5510
Meanwhile I configured the CA Server for SCEP support by intalling the mscep executable from the Resource Kit.
If I try to get the CA's Certificate using crypto ca authenticate MYTRUSTPOINT, i only get this error messages on my ASA console:
Crypto CA thread wakes up!
CRYPTO_PKI: Sending CA Certificate Request:
GET /certsrv/mscep/mscep.dll/pkiclient.exe?operation=GetCACert&message=ITSS HTTP
/1.0
Host: x.x.x.x
CRYPTO_PKI: http connection opened
CRYPTO_PKI: Unable to read CA/RA certificates.Crypto CA thread sleeps!
ERROR: receiving Certificate Authority certificate: status = FAIL, cert length = 0
I have tried to reinstall the CA and SCEP over and over again but I still get the same error all the time. Is there anything wrong with my config?
Please help me with my problem. I promise to give 5-points to anybody who can help me solve my problem. Thank you in advance.
Lorenz

Hi,
Yes now I see the Bug details. But the one I am actually using is a ASA5510, I have also already upgraded it to 7.2.2 (from previous 7.0.7). I have tried this same setup before using Windows2000 Server and ASA5520, and it works. But this time I am having quite a trouble making this thing work.
Lorenz

B2B RosettaNet Rcpt Ack and Excp throws error "Unable to read the preamble"

Hello All,
We have configured a 2 way PIP Config and we are able to succesfully transfer the paload to the TP.
But when receiving the Ackowledgement and Exception, we are getting error "B2B-51705 Unable to read the preamble"
Can anyone help me on this
Thanks,
Sunil

Hi Anuj,
Just want to confirm one more thing
Below given the xsd used for Exception and Acknowledgement
Can you please confirm the format of the same
AcknowledgeMent
===========
<?xml version = "1.0" encoding = "UTF-8"?>









<xsd:schema xmlns:xsd = "http://www.w3.org/2001/XMLSchema">
<xsd:annotation>
     <xsd:documentation>
RosettaNet XML Message Schema
AcknowledgmentOfReceipt_MS_V02_00.dtd
This document has been prepared by Edifecs (http://www.edifecs.com/)
based On the Business Collaboration Framework from requirements
in conformance with the RosettaNet methodology.
     </xsd:documentation>
</xsd:annotation>
     <xsd:element name = "ReceiptAcknowledgment">
          <xsd:complexType>
               <xsd:sequence>
                    <xsd:element ref = "NonRepudiationInformation" minOccurs = "0"/>
               </xsd:sequence>
          </xsd:complexType>
     </xsd:element>
     <xsd:element name = "NonRepudiationInformation">
          <xsd:complexType>
               <xsd:sequence>
                    <xsd:element ref = "OriginalMessageDigest"/>
               </xsd:sequence>
          </xsd:complexType>
     </xsd:element>
     <xsd:element name = "OriginalMessageDigest" type = "xsd:string"/>
</xsd:schema>
Exception
=====
<?xml version="1.0" encoding="UTF-8" standalone="no"?>


<xs:schema xmlns:xs="http://www.w3.org/2001/XMLSchema" elementFormDefault="qualified">
     <xs:import namespace="http://www.w3.org/XML/1998/namespace"/>
     <xs:element name="Exception">
          <xs:complexType>
               <xs:sequence>
                    <xs:element ref="ExceptionDescription"/>
                    <xs:element ref="GlobalExceptionTypeCode"/>
               </xs:sequence>
          </xs:complexType>
     </xs:element>
     <xs:element name="ExceptionDescription">
          <xs:complexType>
               <xs:sequence>
                    <xs:element ref="errorClassification"/>
                    <xs:element ref="errorDescription"/>
                    <xs:element ref="offendingMessageComponent" minOccurs="0"/>
               </xs:sequence>
          </xs:complexType>
     </xs:element>
     <xs:element name="errorClassification">
          <xs:complexType>
               <xs:sequence>
                    <xs:element ref="GlobalMessageExceptionCode"/>
               </xs:sequence>
          </xs:complexType>
     </xs:element>
     <xs:element name="GlobalMessageExceptionCode">
          <xs:complexType mixed="true"/>
     </xs:element>
     <xs:element name="errorDescription">
          <xs:complexType>
               <xs:sequence>
                    <xs:element ref="FreeFormText"/>
               </xs:sequence>
          </xs:complexType>
     </xs:element>
     <xs:element name="FreeFormText">
          <xs:complexType mixed="true">
               <xs:attribute ref="xml:lang"/>
          </xs:complexType>
     </xs:element>
     <xs:element name="offendingMessageComponent">
          <xs:complexType>
               <xs:sequence>
                    <xs:element ref="GlobalMessageComponentCode"/>
               </xs:sequence>
          </xs:complexType>
     </xs:element>
     <xs:element name="GlobalMessageComponentCode">
          <xs:complexType mixed="true"/>
     </xs:element>
     <xs:element name="GlobalExceptionTypeCode">
          <xs:complexType mixed="true"/>
     </xs:element>
</xs:schema>
Pleace correct me if I am wrong in these xsd's
Thanks,
Sunil

Vxiinit unable to intialize config engine

I'm running VXI driver version 2.1 on a Red Hat Linux Operating system. When I try to run vxiinit prior to running resman, I get the following error message:
"vxiinit unable to initialize config engine"
What is the config engine?

Never mind....I figured out the problem....
My NIVXIPATH environment variable was set incorrectly.

Problem to read config file when tomcat used as service

hi,
I have an advanced installer developed for an application and the application is working fine when
my tomcat is used in "manual" mode.But when tomcat is used in "Automatic" mode(as a service)
I'm unable to login into my application, may be unable to read the config.xml....
can any one please help me out with a solution.
Regards,
Vardhan

hi,
I got a solution.Jst change the mode of tomcat and restart the system.
It's working and pls provide with any other solution if you have..
thanx,
Vardhan

WebUtil error: WUC-6: Unable to read WebUtil configuration file

Dear Colleague,
I received the following error:
WUC-6: Unable to read WebUtil configuration file
c:\OraHome_BIForms\forms\server\webutil.cfg
In the meantime, I have verified that my default.env file contains the following path definition:
# webutil config file path
WEBUTIL_CONFIG=C:\OraHome_BIForms\forms\server\webutil.cfg
What is wrong here? Does "unable to read..." mean that the file security settings do not allow read access to the webutil.cfg file?
I would appreciate any advice you can give me.
Thank you and kind regards,
Randy

In the meantime, I have figured out the solution to my problem.
The webutil.cfg file was not in the directory that was being pointed to in the path parameter.
Regards,
Randy

ASDM Unable to read config

Similar Messages

Maybe you are looking for