Asix usb to ethernet adapter and netctl
Hello All!
I'm having difficulty in getting my asix usb ethernet adapter to work with netctl.
# ip addr
1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN
link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
inet 127.0.0.1/8 scope host lo
valid_lft forever preferred_lft forever
inet6 ::1/128 scope host
valid_lft forever preferred_lft forever
2: xxxxxxxxxxxxx
5: usbnet0: <BROADCAST,MULTICAST> mtu 1500 qdisc pfifo_fast state DOWN qlen 1000
link/ether 00:0e:c6:88:fd:a1 brd ff:ff:ff:ff:ff:ff
# cat /etc/netctl/usb
Description='A basic static ethernet connection'
Interface=usbnet0
Connection=ethernet
IP=static
Address=('192.168.5.1/24')
journalctl output after running "netctl start usb"
Sep 30 15:07:14 faubourg systemd[1]: Starting A basic static ethernet connection...
Sep 30 15:07:15 faubourg network[3512]: Starting network profile 'usb'...
Sep 30 15:07:15 faubourg kernel: IPv6: ADDRCONF(NETDEV_UP): usbnet0: link is not ready
Sep 30 15:07:20 faubourg network[3512]: No connection on interface 'usbnet0'
Sep 30 15:07:20 faubourg network[3512]: Failed to bring the network up for profile 'usb'
Sep 30 15:07:20 faubourg systemd[1]: [email protected]: main process exited, code=exited, status=1/FAILURE
Sep 30 15:07:20 faubourg systemd[1]: Failed to start A basic static ethernet connection.
Sep 30 15:07:20 faubourg systemd[1]: Unit [email protected] entered failed state.
I can, however, manually bring the link up and set the ip address.
# ip addr add 192.168.5.1/24 brd 192.168.5.255 dev usbnet0
# ip addr
1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN
link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
inet 127.0.0.1/8 scope host lo
valid_lft forever preferred_lft forever
inet6 ::1/128 scope host
valid_lft forever preferred_lft forever
2: xxxxxxxxxxxxx
6: usbnet0: <BROADCAST,MULTICAST> mtu 1500 qdisc pfifo_fast state DOWN qlen 1000
link/ether 00:0e:c6:88:fd:a1 brd ff:ff:ff:ff:ff:ff
inet 192.168.5.1/24 brd 192.168.5.255 scope global usbnet0
valid_lft forever preferred_lft forever
# ip link set dev usbnet0 up
faubourg netctl # ip addr
1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN
link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
inet 127.0.0.1/8 scope host lo
valid_lft forever preferred_lft forever
inet6 ::1/128 scope host
valid_lft forever preferred_lft forever
2: xxxxxxxxxxxxx
6: usbnet0: <NO-CARRIER,BROADCAST,MULTICAST,UP> mtu 1500 qdisc pfifo_fast state DOWN qlen 1000
link/ether 00:0e:c6:88:fd:a1 brd ff:ff:ff:ff:ff:ff
inet 192.168.5.1/24 brd 192.168.5.255 scope global usbnet0
valid_lft forever preferred_lft forever
inet6 fe80::20e:c6ff:fe88:fda1/64 scope link
valid_lft forever preferred_lft forever
As can be seen, an autoconfiguration ipv6 address based upon my MAC address was automatically added with the ip link command. The lights on the device are still not on and it still fails to communicate. One more command fixes that.
# ethtool -s usbnet0 speed 100 duplex full
# ip addr
1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN
link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
inet 127.0.0.1/8 scope host lo
valid_lft forever preferred_lft forever
inet6 ::1/128 scope host
valid_lft forever preferred_lft forever
2: xxxxxxxxxxxxx
6: usbnet0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state UP qlen 1000
link/ether 00:0e:c6:88:fd:a1 brd ff:ff:ff:ff:ff:ff
inet 192.168.5.1/24 brd 192.168.5.255 scope global usbnet0
valid_lft forever preferred_lft forever
inet6 fe80::20e:c6ff:fe88:fda1/64 scope link
valid_lft forever preferred_lft forever
So my question is, how can I get netctl to do this for me automatically.
bump
Similar Messages
-
I've bought an USB-to-ethernet-adapter and a minidisplay-port-to-VGA-adapter. But I can't use them at the same time. At first, I plugged those two adapters and only the USB-to-ethernet worked. I tried restarting the mac then only the VGA-adapter worked. I also tried to reinstall the OS.
I'm using new 13-inch MacBook Air early 2015. OS X 10.10.3.Thanks Malcolm - Do you think it might be worth trying to flash the firmware on these cases - there seem to be updaters available on Prolific's website. Obviously I'd have to do it on a PC. I've emailed Prolific asking them about my problem. No reply as yet, and I'm not holding my breath! Do you know if there are any other posts on these boards relating to Prolific? Stupid question really - I'll just do a search...
Thanks again for your post. Cheers from Bonnie Scotland. -
I need a USB/FireWire ethernet adapter
About 6 months ago my ethernet port was fried when a lightning bolt sent a surge through the wire. Since then i have been using my family's wireless network, but now that I am back in school and away from home, i don't have that luxury. So, i've been looking for a Mac compatible USB/FireWire ethernet adapter and have had no luck. If anyone knows where I can find one, let me know.
Hi Kllru,
Welcome to the Discussions.
The following link has info on compatible adapters as well as a driver for OS X.
http://www.sustworks.com/site/newsusbethernet.html
John -
Unusual issue with tag engine and BELKIN USB to Ethernet adapter??
I have an .scf file with 72 tags and several tag groups in it. If I open the tag engine without the usb adapter, I can read the tag group names with the get group list.vi. The tag group names are listed in black letters when wired to an indicator. When I plug in the usb ethernet adapter, immediately the group tag names are greyed out in the indicator without even running the vi. If I put a tag constant on the block diagram and try to select a tag name with the pointer, no tagnames pop up. It worked yesterday and my IT. department sent down a shockwave and flash5 update download when I booted up this morning. anyone have any ideas??
I am still seeing the tag groups disappear when I start the tag engine on labview7.0. I have several other programs running at the same time, KEPWARE, PROWORX NXT, USB to ethernet adapter. This is on a win2000 machine.
Attachments:
op50_head_press_force_status_rev2.vi 320 KB
Process_Sta2_probe_results.vi 42 KB
op50_head_version2.scf 53 KB -
HELP: USB to Ethernet Adapter
Hello Everyone. I have a USB to Ethernet adapter for my Macbook Pro Retina. After plugging it into an ethernet cable and connecting everything, my computer still isn't reading it. I am wondering if there is an install driver or what or if I am doing something wrong. Thanks you for your help.
Brb8910,
what is the brand and model of your USB-to-Ethernet adapter? Does the manufacturer claim that it is compatible with your installed version of OS X? -
Lenovo X131e doesn't work with Prolific PL2303 based USB to Serial Adapter and Windows 7 x64
This is sort of a bug report. A Lenovo X131e with Windows 7 x64 and the PL2303 driver including 1.6, 1.61 and 1.7 will not successfully install the driver - Windows always reports "Driver Install Failed" on plug in to USB 3 or USB2 ports. However, putting a USB2.0 hub inbetween the USB to Serial Adapter and either USB port type makes the adapter work fine. This was not the case with the X130e. I'm not sure where to report this beyond this posting, but more of an FYI.
If the USB can be used for other equipment,
That may be compatibility issues for USB and Prolific PL2303.
Don't plug Serial Adapter when installing the driver,
Ofter installation, Connect serial adapter to see whether it is working normally.
I am a volunteer, don't work for Lenovo. I am a software engineer.
thinkpad x61t, os:win7 Awavo Software com port monitor serial port monitor -
Third-Party USB to Ethernet Adapter not working since 10.8 updated
Hi I have a third-party USB to Ethernet adapter. Since the update of mountain lion the adapter does not work.
Is there a driver or something I can do to make it work?
ThanksUSB not so good, this very good.
Thunderbolt to Gigabit Ethernet Adapter -
I have a new airbook, 10.7.4 LION, thunderbolt ethernet adapter and when trying to install 1.2.1 thunderbolt upgrade it says "this software not supported on this system"? Any advice on how to get the adapter to work?
Welcome to Apple Support Communities
If you purchased the computer before 2010, your computer hasn't got Thunderbolt, so you can't use it -
Apple USB to Ethernet Adapter??
Can you use the Apple " usb to ethernet " adapter with the airport express?
The USB port on the AirPort Express will only support a compatible printer, so using a USB to Ethernet adapter would not accomplish what you want to do.
If you add a simple 5 port Ethernet switch to the AirPort Express, one port will be used to connect to the Express with an Ethernet cable. You will then have 4 Ethernet ports available for devices.
Any major electronic/computer store will have what you need. Netgear or Cisco-Linksys make quality products. -
Can`t setup my Ax88772a USB Fast Ethernet Adapter! Driver is already downloaded
Can`t setup my Ax88772a USB Fast Ethernet Adapter! Driver is already downloaded
Can`t setup my Ax88772a USB Fast Ethernet Adapter! Driver is already downloaded
-
Apple USB Ethernet Adapter and VLAN??
Bought the Apple USB Ethernet Adapter today because my built in ethernetport on my MBP stopped working. What I know I need to replace the motherboard to have it fixed, so I thought the USB adapter could be useful until then.
But, it didn't work! I only got a "Self assigned ip-address". No matter what I do. I also entered an ip-address manually with no success.
Later at home I tested again, and Voila!! It worked perfectly!
Back at the office, same problem... I only get a "Self assigned ip-address"...
My conclusion of this is that the Apple USB Ethernet Adapter doesn't support VLAN?? Could anyone confirm that or better of, suggest a solution??
Would appreciate it a lot!
PS. Yes we do have Wi-Fi, but it's restricted and is not a solution for me. DS.Create a new network location and try again.
https://discussions.apple.com/thread/2624518?threadID=2624518&tstart=45 -
Usb to Ethernet adapter doesn't work? AX88772B
I don't know how to make a connection with Internet with RJ-45 cable with the usb adapter.
I have MBA. Lion 10.7.5
Now I need to connect MBA by RJ-45 cable with usb adapter (asus AX88772B)
MBA see the adapter (even without an ethernet cable).
I also did download drivers from here http://www.asix.com.tw/products.php?op=pItemdetail&PItemID=105;71;101&PLine=71
I read the instruction, and I've done 3 steps on the page 4 exept these one's:
(4) Set the permission access mode of Apple’s default driver.
(5) Update the access and modification times of ASIX’s AX88772B/772A/760/772 or AX88178 driver.
But i don't know how to do this.
In the system report is always written this:
AX88772B:
Product ID: 0x7e2b
Vendor ID: 0x0b95 (ASIX Electronics Corporation)
Version: 0.01
Serial Number: 09EF51
Speed: Up to 480 Mb/sec
Manufacturer: ASIX Elec. Corp.
Location ID: 0xfd120000 / 4
Current Available (mA): 500
Current Required (mA): Unknown (Device has not been configured)NO
But still I can't make an Usb to Ethernet connection in system preferenes, nothing written about it there.Hmm. Well I tried rebooting with wifi off but that didn't fix things for me. Would you mind sharing what your System Information says under Thunderbolt? This is what mine looks like:
MacBook Pro:
Vendor Name: Apple, Inc.
Device Name: Macintosh
UID: 0x0001000D1290C120
Firmware Version: 11.1
Port:
Status: No devices connected
Link Status: 7
Link Controller Firmware Version: 0.11.4
Port:
Status: Connected
Link Status: 2
Link Controller Firmware Version: 0.11.4
Thunderbolt to Gigabit Ethernet Adapter:
Vendor Name: Apple, Inc.
Device Name: Thunderbolt to Gigabit Ethernet Adapter
Vendor ID: 0x1
Device ID: 0x8003
Device Revision: 0x1
UID: 0x000100020059EBB0
Apple Serial Number: DTN224606LWDWKHAX
Route String: 3
Firmware Version: 5.5
Port:
Status: Connected
Link Status: 2
Port Micro Firmware Version: 0.0.8 -
Why is this usb to ethernet adapter so cheap?
Hi,
I need an enthernet Adapter for my macbook air and found this one:
http://www.ebay.de/itm/USB-2-0-Adaptor-Ethernet-Adapter-Apple-Macbook-Air-brandn eu-Top-Qualitat-/170717342238?pt=Apple_Zubeh%C3%B6r&hash=item27bf8bea1e#ht_2389w t_982
is it original Apple?
Best regards,
ChrisIsn't that what it says? Apple's online price is $29.00 USD.
-
USB to RS232 Adapter and Driver Advise - Heeeeelllllllpppppp Please!!
Hi All,
Can someone please help me with an issue im having.
I currently have a hl-340 usb to rs232 adapter for me to be able to Console on to cisco equipment (as i am a network engineer).
I can not get this to work!! i have installed the pl2303 driver as recommended by the place who sold this to me on ebay which has not worked, i have looked around and saw the option of installing the keyspan for this product USA-19HS but with no joy.
I need to get this working ASAP or look to purchase a new one. I am based in the UK so if it is not possible to get this working then can you advise on what one will work?
I am a novice to the Mac so any assistance you can all give will be greatly received.
ThanksLet's figure out what you have first. Plug in you RS-232 adapter. If the system has a driver that recognizes it, it should pop up a window about detecting a new network interface. If that happens, your USB device is recognized and should be working. If not, you may have the wrong driver loaded.
In any case, open the System Profiler application (click the Apple logo in the menu bar, then About This Mac, then More Info). When the app opens, click USB (under the Hardware heading) in the left window pane. This will reveal all detected USB buses, hubs, and devices. On my system, my RS-232 adapter shows up as USB-Serial Controller. Clicking on it shows these details in the bottom pane:
USB-Serial Controller:
Product ID: 0x4026
Vendor ID: 0x1453
Version: 3.00
Speed: Up to 12 Mb/sec
Manufacturer: Prolific Technology Inc.
Location ID: 0xfd323000
Current Available (mA): 500
Current Required (mA): 100
Your details may be different, especially the Product and Vendor ID. For the PL2303 driver to work, I think the important part is that the Manufacturer is Prolific Technology. If it's something else, you may need a different driver. Try to find your device, and reply back with its details.
With the adapter still connected, click Extensions (under the Software heading) in the left window pane. A list of all kernel extensions will be displayed. This will take a while.
On my system, with the driver that I recommended, the extension name is osx-pl2303. Clicking on it shows these details in the bottom pane:
osx-pl2303:
Version: 1.0.0d1
Last Modified: 05/27/06 11:49
Kind: Universal
Architectures: i386, ppc
64-Bit (Intel): No
Location: /System/Library/Extensions/osx-pl2303.kext
Kext Version: 1.0.0d1
Load Address: 0x3599e000
Valid: Yes
Authentic: Yes
Dependencies: Satisfied
If yours also displays this, then your device should be working. If so, then you'll need to figure out how to get your software to recognize it. Reply back with whatever details you find. -
MacBook Pro turns off when USB to Ethernet adapter is unplugged.
Hi all!
As the title says, whenever I unplug my MacBook Pro from the network (plugged in via a USB to RJ45 adapter) the MacBook Pro powers down.
I would appreciate any help with this.
Cheers!Try SMC and NVRAM resets:
https://support.apple.com/en-us/HT201295
https://support.apple.com/en-us/HT204063
If no success, bring the MBP into a genius bar for a FREE evaluation.
Ciao.
Maybe you are looking for
-
Hello Experts, We have requirement of printing Some text in PO Header. Scenario is we are using Automatic PO option for creating the Purchase order directly from PR having document type YA only. We want to print certain Fix Text details to be printed
-
Issue in uploading Employee Group and subgroup in LSMW
Hi Experts, I`m using LSMW to upload IT 1013 data thru transaction PP01. When i run the LSMW in forground mode , then everything seems to work fine. But when run in background mode, I find that the records are not getting uploaded and its giving m
-
Issue telated to STO return invoice
hi expert, 1) user have created PO then created delivery then Invoice. now user have created return delivery and when user try to bill the return quentity. system give error" sales organisation is not define" so guid me where to check and its transec
-
Recently I was at work, and my blackberry restarted, when it loaded, all my contacts had disappeared, originally i had thought that a filter had been applied, which wasn't that case, when i go to options to select my contact list, it shows that there
-
What is really new in JSC2 Update 1?
Are there any enhancements made to update 1 except DB change, new version of application server bundled and all the hot fixes and patches included witch were already available to JSC2.