ASR 1001 IOS upgrade issue

Hi I am changing IOS of Cisco ASR 1001 from asr1001-universalk9.03.07.02.S.152-4.S2.bin
to asr1000rp1-adventerprisek9.03.04.02.S.151-3.S2.bin but everty time it boot up with old IOS universalk9.
Is it becaused of Licence issue.
Router#sh bootvar
BOOT variable = bootflash:asr1000rp1-adventerprisek9.03.04.02.S.151-3.S2.bin,12;bootflash:asr1001-universalk9.03.07.02.S.152-4.S2.bin,12;
CONFIG_FILE variable does not exist
BOOTLDR variable does not exist
Configuration register is 0x2102
License Level: advipservices
License Type: Permanent
Next reload license Level: advipservices
cisco ASR1001 (1RU) processor with 1155941K/6147K bytes of memory.
Processor board ID SSI1607042B
4 Gigabit Ethernet interfaces
32768K bytes of non-volatile configuration memory.
4194304K bytes of physical memory.
7741439K bytes of eUSB flash at bootflash:.
Configuration register is 0x2102

You downloaded the wrong file. The file you wanted to run has "rp1" but the original file doesn't. You downloaded a file for a different model. Your router is an ASR 1001 with fixed RP but you've downloaded a file for a different sub-model of ASR, like the 1002 or 1004.
Go here instead: http://software.cisco.com/download/release.html?mdfid=282993672&softwareid=282046477&release=3.10.3S&relind=AVAILABLE&rellifecycle=ED&reltype=latest

Similar Messages

Iphone ios upgrade issue

I am unable to upgrade my iphone 3g Model number MB489HN. i STILL HAVE IOS VER 4.1. Please advise.

I am having the same issue on my Macbook Pro running 10.6.6, and the latest iTunes 10.2.1.
I have iOS4 4.2 and I'm trying to upgrade to 4.3. I get the exact same message. This happens on my internet connection at the office as well as at home.

2960s IOS Upgrade Issue

Hi
I have a issue when i try to upgrade the IOS of WS-C2960S-48TS-L, the curretn version is 12.2(58)SE2 , the verison im trying to upgrate to is 15.2.SE6.
I do the "archive tar /xtract tftp" command to extract all the files to the flash, then i do the "boot system flash:" command to change to the new but when i reboot the switch it loads the new ios then loads the old ios and boot using the old ios, how can i change to ignore the old ios ?

Here i am again...and with new weird news.
I've made new tests and analisys on my six WS-2960S-48LPS-L.
Cables are ok (said by TDR).
Five on six no way to upgrade, from CLI, upper 15.0.1-SE. This is the newest working IOS i found, tested:
c2960s-universalk9-mz.150-2.EX
c2960s-universalk9-mz.150-2.SE6
c2960s-universalk9-mz.150-2.SE6 <-- suggested by Cisco
c2960s-universalk9-mz.150-2.SE7
c2960s-universalk9-mz.152-2a.E1
no way to boot, always the same error i've already posted.
Tried to format the rom also, always same things.
Anyway with 15.0.1-SE that should have fixed the poe problems, poe doesnt work...So i guess it's a hardware problem. Well ...5/6... i must say i have really bad luck...
But now, give me your attention please.....
One of them works, every port do its job with my voip cisco 7912 phones, with an old IOS also (12.2.58-SE2). So, i checked if it is a 2960S-48LPS-L for sure, serial number on case is the same i have on the package. It says it's a LPS-L. So, from CLI, i tried a show version....look at this:
Cisco IOS Software, C2960S Software (C2960S-UNIVERSALK9-M), Version 12.2(55)SE8, RELEASE SOFTWARE (fc2)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2013 by Cisco Systems, Inc.
Compiled Wed 26-Jun-13 11:40 by prod_rel_team
Image text-base: 0x00003000, data-base: 0x01B00000
ROM: Bootstrap program is Alpha board boot loader
BOOTLDR: C2960S Boot Loader (C2960S-HBOOT-M) Version 12.2(53r)SE, RELEASE SOFTWARE (fc3)
Vigili uptime is 6 days, 21 hours, 54 minutes
System returned to ROM by power-on
System restarted at 12:01:56 UTC Wed Apr 1 2015
System image file is "flash:/c2960s-universalk9-mz.122-55.SE8/c2960s-universalk9-mz.122-55.SE8.bin"
This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.
A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html
If you require further assistance please contact us by sending email to
[email protected].
cisco WS-C2960S-48FPS-L (PowerPC) processor (revision H0) with 131072K bytes of memory.
Processor board ID FOC1726Z0GN
Last reset from power-on
1 Virtual Ethernet interface
1 FastEthernet interface
52 Gigabit Ethernet interfaces
The password-recovery mechanism is enabled.
512K bytes of flash-simulated non-volatile configuration memory.
Base ethernet MAC Address       : 84:80:2D:0D:F8:00
Motherboard assembly number     : 73-11908-09
Power supply part number        : 341-0393-02
Motherboard serial number       : FOC183811TD
Power supply serial number      : LIT183101SG
Model revision number           : H0
Motherboard revision number     : A0
Model number                    : WS-C2960S-48LPS-L
Daughterboard assembly number   : 73-11933-04
Daughterboard serial number     : FOC18376CNB
System serial number            : FOC1726Z0GN
Top Assembly Part Number        : 800-30945-04
Top Assembly Revision Number    : C0
Version ID                      : V04
CLEI Code Number                : COMGZOOARD
Daughterboard revision number   : A0
Hardware Board Revision Number : 0x01
Switch Ports Model              SW Version            SW Image
*    1 52    WS-C2960S-48FPS-L 12.2(55)SE8           C2960S-UNIVERSALK9-M
now i'm really confused...
I called Cisco, gave them the serial number and they confirmed must be a LPS-L.
Ideas?

IPad IOS upgrade issue

I have the original iPad. The IOS is 5.1.1. It tells me that this is the latest version. I can not upgrade to the latest IOS version 7.x and therefore can not use new apps. Any insights?

The hardware for your iPad only supports up to iOS 5. You cannot upgrade to iOS 6 or iOS 7.

New ios upgrade issue

My iphone after the last upgrade 6.0.1 is hung up all the time when I try to reach the settings and apps on it. FYI. Can I downgrade it to the previous version. Let me know.

Try user troubleshooting restart, reset http://support.apple.com/kb/HT1430, then restore from backup, restore as new. http://support.apple.com/kb/HT1414

3750 IOS Upgrade Issue

So I have a bunch of 3750s in my network...upgrade them all the same way. Today I recieved 3 new ones...upgraded the first one no problem...during the second I recieve the following:
Switch#$overwrite /reload tftp://10.20.11.15/c3750-i5k91-tar.122-20.SE3.tar
Unable to create temp dir "flash:update"
Switch#$overwrite /reload tftp://10.20.11.15/c3750-i5k91-tar.122-20.SE3.tar
Anybody have any clue how to get around this?
bc

Alok,
I gave that a whirl and it was a no go. I recieved the following error msgs:
Switch#rmdir flash:update
Remove directory filename [update]?
Delete flash:update? [confirm]
%Error Removing dir flash:update (Unknown error 93)
Switch#rmdir flash:update
Remove directory filename [update]?
Delete flash:update? [confirm]
%Error Removing dir flash:update (Unknown error 93)
Switch#
Let me know if you have any clue what is gonig on!
bc

ASR 1001 Licence Activation

Hello, Try as I might I cant find a document that says;
"How to activate encryption on an ASR 1001" or "activating ip advanced features" on the ASR 1001.
Can anyone help please. My Kit list.
Cisco ASR1001 System,Crypto, 4 built-in GE, Dual P/S
Cisco ASR1001 4GB DRAM
Cisco ASR 1000 Advanced IP Services License
Cisco ASR 1001 IOS XE - ENCRYPTION UNIVERSAL
IPSEC License for ASR1000 Series
Upgrade from 2.5 Gbps to 5Gbps License for ASR 1001
Whats the process to activate the 2.5gbps to 5gbps feature or encryption?
Thanks
Chris

Chris,
The ASR1000 feature licensing is explained on the document http://www.cisco.com/en/US/prod/collateral/routers/ps9343/product_bulletin_c25-448292.html
You can also find this information on the product datasheet at http://www.cisco.com/en/US/prod/collateral/routers/ps9343/data_sheet_c78-447652.html
Regarding IPSec and Bandwidth licenses on ASR1K, see below and excerpt from datasheet:
Cisco ASR1001 Feature Licenses: Enforced with PAK
FLSASR1001-5G
Upgrade from 2.5 Gbps to 5Gbps License for ASR 1001
FLSASR1001-5G=
Upgrade from 2.5 Gbps to 5Gbps Paper PAK for ASR 1001
L-FLSASR1001-5G=
Upgrade from 2.5 Gbps to 5Gbps E-Delivery PAK for ASR 1001
Security
FLSASR1-IPSEC
IPSEC License for ASR1000 Series
FL-ASR1-IPSEC=
IPSEC Paper PAK for ASR1000 Series
L-FL-ASR1-IPSEC=
IPSEC E-Delivery PAK for ASR1000 Series
Cheers, Gustavo

ASR 1001 Router enquiry on fiber handoff

Cisco ASR 1001 Router would support fiber hand-off of the link. Below is the Specifications of the Router - we received from vendor:
Description
Quantity
Cisco ASR1001 System,Crypto, 4 built-in GE, Dual P/S
1
Cisco 5-Port Gigabit Ethernet Shared Port Adapter
1
1000BASE-LX/LH SFP transceiver module, MMF/SMF, 1310nm, DOM
2
Cisco ASR1001 AC Power Supply
2
Power Cord India, Right Angle
2
Cisco ASR 1001 IOS XE UNIVERSAL - NO ENCRYPTION
1
Cisco ASR 1000 IP BASE License
1
SPA for ASR1000; No Physical Part; For Tracking Only
1
Cisco ASR1001 4GB DRAM
1
PRTNR SS 8X5XNBD Cisco ASR1001 System,Crypto
1
PRTNR SS 8X5XNBD Cisco ASR 1000 IP BASE License
1
PRTNR SS 8X5XNBD 5-Pt Gigabit Enet Shared Pt Adptr
1
Datacenter feature: There will be fiber connections already installed at the DMZ site from the meet me telco room to the partner racks. Therefore, your service provider must understand that they will do a circuit handoff to fiber and order the routers, interface cards, connectors, etc. to support fiber circuit extension.

You can use standard Ethernet copper or Fiber, providing that you have the correct SFP/GBICs.
As long as you have the correct SFP's you need for the ASR - All should be good.
http://www.cisco.com/en/US/docs/interfaces_modules/shared_port_adapters/install_upgrade/ASR1000/ASRintro.html#wp1235447
http://www.cisco.com/en/US/prod/collateral/modules/ps5455/ps6577/product_data_sheet0900aecd8033f885.html
hth

ASR 1001 L2TP sessions // License issue?

Hello,
This is my first post, in the fisrt place, sorry for my english, is not my native language.
I have purchased a refurbished ASR 1001 without any license for using as LNS:
Cisco IOS XE Software, Version 03.12.00.S - Standard Support Release
Cisco IOS Software, ASR1000 Software (X86_64_LINUX_IOSD-UNIVERSALK9-M), Version 15.4(2)S, RELEASE SOFTWARE (fc2)
asr1001-universalk9.03.12.00.S.154-2.S-std.bin
The scenario is this:
LAC (from network provider) send L2TP packet sessions-> LNS (ASR 1001, assign public IP to user and close the L2TP session).
The configuration of ASR is the typical for xDSL connections.
1) The LAC send requests to LNS Loopback interface:
interface Loopbacktest1
ip address 5.6.7.8 255.255.255.255
snmp ifindex persist
2) LNS assign the loopback interface to vpdn group, that points to virtual-template:
vpdn-group VpdnG1
accept-dialin
protocol l2tp
virtual-template 1
terminate-from hostname Provider01
dsl-line-info-forwarding
source-ip 5.6.7.8
lcp renegotiation always
l2tp tunnel password 7 XXXXXXXX
interface Virtual-Template1
description Int-Vi1 VpdnG1
mtu 1501
ip unnumbered GigabitEthernetX/X/X
ip mtu 1460
ip tcp adjust-mss 1400
no peer default ip address
ppp max-terminate 255
ppp max-configure 255
ppp max-failure 255
ppp max-bad-auth 10
ppp authentication pap chap ppp_authent2
ppp multilink
Since here, all is OK, but the problem is that the ASR cannot reach connected users and evidently the user doesn't have internet connectivity because he cannot reach the gateway IP (ASR IP).
Interface User Mode Idle Peer Address
Vi1.1 test1 PPPoVPDN - 1.2.3.4
L2TP Tunnel and Session Information Total tunnels 1 sessions 1
LocTunID RemTunID Remote Name State Remote Address Sessn L2TP Class/
Count VPDN Group
1589 3324 Provider01 est 5.6.7.8 1 VpdnG1
ASR1001#ping 1.2.3.4
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 1.2.3.4, timeout is 2 seconds:
Success rate is 0 percent (0/5)
ASR1001 in not forwardinf the traffic to end users
Exactly the same configuration works fine in 7201 cisco router.
After read some information in internet and cisco web and test several IOS images and configurations I have activated 2 of 3 (marked in bold down) possible licenses that are available to test in the router (these are available during 60 days).
SLASR1-IPB
Cisco ASR 1000 IP BASE License
SLASR1-AIS
Cisco ASR 1000 Advanced IP Services License
SLASR1-AES
Cisco ASR 1000 Advanced Enterprise Services License
***Result-> After apply Advanced IP Service or Advanced Enterprise license the ASR works perfectly, forwarding the traffic to the end users. The router can reach gateway and have internet connection.
I would like to try IP BASE License but there is no possibility to activate the test period in the router, I don't know if you knows any way to test it. This is the details that router shows about this 3 license types:
Index 1 Feature: adventerprise
Period left: 8 weeks 1 day
Period Used: 2 days 12 hours
License Type: EvalRightToUse
License State: Active, In Use
License Count: Non-Counted
License Priority: Low
Index 2 Feature: advipservices
Period left: Not Activated
Period Used: 0 minute 0 second
License Type: EvalRightToUse
License State: Active, Not in Use, EULA not accepted
License Count: Non-Counted
License Priority: None
Index 3 Feature: ipbase
-->There is no more info about IP base license<---
If I use the command "license boot level" I can apply the IP base license, but after reload the router, nothing happens.
ASR1001(config)#license boot level ?
adventerprise Advanced Enterprise License Level
advipservices Advanced IP Services License Level
ipbase IP Base License Level
Then my answers are:
1) Is 100% necessary to have a license in ASR1001 to use the router as LNS as showed? Apparently after my tests I will answer "yes", but I'm not sure if my configuration is the only one that I can configure. Maybe exist another way to config the required scenario and avoid the purchase license.
2) Do you know if IP Base license will active the forwarding packet function in the ASR? I think yes, but before buy this license I need to be sure. As you know Ip Base is the most cheap license.
Thanks in advantage!
Regards

Hello,
Documentation states that licensing on the ASR 1000 are now honor-based since 3.7s. I didn't test it though.
Basically, your license marked now as "EvalRTU" will be moved to an "RTU" license, indicating you would need to buy a license to keep your honor intact, but no disruption in features or connectivity will happen.
Since your test was more than 60 days ago, can you confirm this behavior with 3.12 ?
Thanks,
Kind regards,
Sources:
- All Cisco ASR 1000 feature and performance upgrade licenses are honor-based; that is, they are not enforced through a PAK (Product Activation Key). Note: Prior to Cisco IOS XE Software Release 3.7S, performance upgrade licenses that are required to upgrade the Cisco ASR 1001 from 2.5 to 5 Gbps or the Cisco ASR 1002-X from 5 to 10 to 20 to 36 Gbps are enforced through a PAK. Similarly, prior to Cisco IOS XE Software Release 3.6S, technology package licenses are enforced through a PAK. [1]
- When the 60-Day Evaluation Period expires, the license automatically changes to an RTU license. As with all other RTU licenses, there is no functionality disruption or accessibility concerns following this transition. [2]
[1] http://www.cisco.com/c/en/us/products/collateral/routers/asr-1000-series-aggregation-services-routers/guide-c07-731639.html
[2] http://www.cisco.com/c/en/us/td/docs/routers/asr1000/install/guide/1001-x/asr1hig/asr1lic.html

I bought a Sandisk Connect Media Drive, downloaded the app from iTunes. Before iOS 8, movies played fine. After iOS upgrade I can no longer play movies downloaded from iTunes to the media drive. Anyone else have a similar issue?

I bought a Sandisk Connect Media Drive, downloaded the app from iTunes. Before iOS 8, movies played fine. After iOS upgrade I can no longer play movies downloaded from iTunes to the media drive. Anyone else have a similar issue?

I checked with SanDisk's own online support and they indicate that they have notified Apple of the issue.
According to SanDisk, the problem lies with Apple not having the iOS 8 version of the Safari browser having DRM decoding enabled that the Media Drive relies upon to decode and play iTunes DRM titles. Non DRM encoded videos will play in the browser.
DRM audio is not effected as this is handled by the native iOS music app.
As of the date of this post SanDisk have not been given a timeframe by Apple for this issue to be resolved.
I hope that Apple resolves this issue quickly as I have a large collection of DRM video titles on a 128Mb memory card installed in the Media Drive that I am unable to view.

ASR 1001 SFP issue

I am working on putting a loaner ASR 1001 into my infrastructure to replace my 7206 VXR. Currently my uplink to my ISP is fiber and runs into an GBIC SX MM transceiver. No issue with connectivity. When i change the fiber patch over to LC I connect it to the ASR 1001 GBIC and I get no link. Tried changed negotiation auto to no negotiation auto not affect. I then took the fiber and connected to a gbic I have in a 3560 switch link comes right up. At this point I am a bit stumped. Tried moving the configuration to a different interface on the ASR no luck. Totally confused.

What model transceiver are you using on the ASR? I didn't tink they took GBICs - ony SFPs. I think the one you would need is an SFP (the GLC-SX-MMD or GLC-SX-MM without DOM). That's what's compatible on an ASR 1001 for 1 Gbps MM fiber per the compatibility matrix.
Is the ASR recognizing the transceiver? (show int ___)

POE 3560 Issue after IOS upgrade

Hello,
I having issue where 6 WLAN AP's not coming back uo after reboot and IOS upgrade of 3560 POE swtiches - . Prior to changes here most if not all ALL the 23 Aps were mainly on one switch, Now after these changes they are now spread over three switches ( 3560's) - with 17 coming back on line
I am sure its not the power limitation of the switch(s) as the one switch I am TS at present had a fairly large allocation of the aps attached prior to ios upgrade and reload. and the available power value now showing is applicable.for 8 AP's
I have tried various TS steps to try and bring them back up - A couple of things I would like to try but I am restricted to do so is to check the APS physically or downgrade the ios!
Any input on this matter would be truly appreciated.- (attached is the log buffer debug)
res
Paul

c3560-ipbase-mz.122-25.SEE2.bin
You upgraded the IOS to the switch? I shudder at the thought of what old version did you upgrade FROM.
Available:370.0(w) Used:110.4(w) Remaining:259.6(w)
You've got more than enough PoE left.
Only two things comes to my mind:
1. Cable issue - Unfortunately, the 3560 is a non-GigabitEthernet and this particular sub-model does NOT support TDR.
2. Hardware failure - Read THIS.

Cisco 4500X IOS upgrade through ISSU

Hi,
I am having 2 number of cisco 4500x switch and configured with VSS
so one switch is active and another switch is standby.
I am panning to upgrade IOS through ISSU
i read in document that it required auto boot enable in switch.
My switch current Configuration register = 0x2101
do i need to change config register or this will ok. If need to change then what will be auto boot and after IOS upgrade do i need to change it again.
Please help....

Hello Tarun,
Please find below the steps to perform the ISSU:
ISSU Prerequisites
Before one can perform an ISSU, there are a few prerequisites one must verify for a successful ISSU. The following list explains what is initially required.
• Must be using a redundant Cisco Catalyst 4500 switch with symmetric hardware (that is, supervisors, memory, rommon, NFL daughter card, and so on).
• Both new and old Cisco IOS Software images must be preloaded to the file system on both supervisors.
• SSO must be configured and working properly.
• Config register must be configured to autoboot (that is, the value should have a "2" in the lowest byte).
45010R-203# sh bootvar | i register
Configuration register is 0x2102
Standby Configuration register is 0x2102
Several commands are available to verify if SSO is enabled:
4510R-203# sh module | b Redundancy
Mod  Redundancy role     Operating mode      Redundancy status
----+-------------------+-------------------+-------------------
1   Standby Supervisor   SSO                  Standby hot
2   Active Supervisor    SSO                 Active
45010R-203# sh redundancy states
       my state = 13 -ACTIVE
     peer state = 8   -STANDBY HOT
           Mode = Duplex
           Unit = Secondary
        Unit ID = 2
Redundancy Mode (Operational) =  Stateful Switchover
Redundancy Mode (Configured)  =  Stateful Switchover
Redundancy State              =  Stateful Switchover
             <snip>
4507R-ISSU# sh run | b redundancy
redundancy
mode  sso
As a step prior to the beginning of the ISSU process, the new version of the Cisco IOS Software image needs to be loaded into both the active and standby supervisors' file systems. Both active and standby supervisor need to contain both the new and old images in the file system. In order to store both new and old images, the supervisors should be upgraded to contain sufficient amounts of flash memory prior to the ISSU process.
The new images can be downloaded into both supervisors using commands such as:
copy tftp: bootflash:
copy tftp: slavebootflash:
The example below illustrates this verification:
4510R-203#dir
Directory of bootflash:/
1  -rwx 13636500 Sep 6 2006 03:18:58 -08:00 cat4500-entservices-mz.122-31.SGA
2  -rwx 13747611 Sep 9 2006 03:19:58 -08:00 cat4500-entservices-mz.122-31.SGA1
4510R-203#dir slavebootflash:
Directory of slavebootflash:/
1  -rwx 13636500 Sep 6 2006 03:18:58 -08:00 cat4500-entservices-mz.122-31.SGA
2  -rwx 13747611 Sep 9 2006 03:19:58 -08:00 cat4500-entservices-mz.122-31.SGA1
Once this check is verified, one can now proceed with the ISSU process.
The ISSU process is started by typing the "issu loadversion" command on the active supervisor. This command directs the active supervisor to begin the ISSU process. The active supervisor, through intersupervisor communications, checks that the requested image has been downloaded into both the active and standby supervisors' file systems. If the required images are not present, the command is rejected, and an appropriate warning is generated.
If the "issu loadversion" command is successful, the switch transitions into the "Load Version" ISSU state. The standby supervisor will reset and boot with the new version of the Cisco IOS Software image loaded into the file system.
The following actions take place when the command is implemented:
1. The standby supervisor (B) is reset.
2. The standby supervisor (B) is booted with the new Cisco IOS Software image: Release 12.2(31)SGA1.
3. If both Cisco IOS Software images are declared as compatible, the standby supervisor moves into SSO mode and is fully stateful for all compatible clients and applications. Compatibility allows for in-service software upgrade or downgrade between two versions to succeed with minimal service effect.
4. If both Cisco IOS Software images are incompatible, the system moves into RPR mode, and the ISSU process is terminated with an appropriate message to the user. Images are declared incompatible when "required" clients or applications are not interoperable between two Cisco IOS Software releases.
5. Standby "B" reaches the standby HOT state.
6. The user has an option to abort the ISSU process by issuing the "issu abortversion" command.
7. The "issu loadversion" command also supports a "forced" option that allows the operator to force the system into entering RPR mode when incompatibility is detected.
Note: When performing an ISSU, disable manual switchovers. Performing manual switchovers during the issu process is strongly discouraged. The current implementation does not prevent it, but it does display a warning to the user.
An example of the CLI for implementing the issu loadversion command is displayed below.
On the active supervisor, one would issue the following command:
4510R-203#issu loadversion 1 bootflash:cat4500-entservices-mz.122-31.SGA1 2 slavebootflash: cat4500-entservices-mz.122-31.SGA1
Syntax - issu loadversion active-slot active-image-new standby-slot standby-image-new
The second step of the ISSU process is to perform the issu runversion CLI.
The user can issue the " issu runversion" command when:
1. The ISSU state is "Load Version"; this can be verified with the "show issu state detail" CLI.
2. The standby supervisor is running the new version of the software.
3. The standby supervisor has moved into the "Standby Hot " state.
The following actions take place when the " issu runversion" command is executed:
1. A switchover occurs; that is, the standby (B) becomes the new active, and the old active (A) is rebooted and comes up as a standby.
2. A timer called "Rollback Timer" is started with a previously configured value.
3. Move both supervisors to "Run Version" state.
4. If the command "issu acceptversion" is not issued before the "Rollback timer" fires, then the entire ISSU process is aborted via the automatic rollback.
5. If the active supervisor console connectivity is established and the "issu acceptversion" command is issued, then the rollback timer is stopped.
6. The user has an option to abort the ISSU process by issuing the "issu abortversion" command.
An example of the CLI for implementing the issu runversion command is displayed below:
On the active supervisor, one would issue the following command:
4510R-203#issu runversion 2 slavebootflash:cat4500-entservices-mz.122-31.SGA1
Syntax - issu runversion standby-slot [standby-image-new]
Prior to issuing the `issu acceptversion' command the system will be counting down the rollback timer. If `issu acceptversion' is not completed before rollback timer expires an automatic abort will occur. This command stops the "Rollback Timer." This command serves as a feedback mechanism. This is an optional command and can be skipped in the ISSU process with the "issu commitversion" CLI.
If this command is not issued within 45 minutes (default) from the time the standby supervisor moves into the "Standby Hot" state, it is assumed that the new active supervisor is not reachable and the entire ISSU process is rolled back to the previous version of the software. The acceptversion is not intended for long-term network operation. It is also important to note that none of the features available on the new version will work yet.
The following actions take place when the command is implemented:
1. The "Rollback Timer" is terminated. This means that the rollback timer is not looked at anymore. Therefore, the system can run in this state for an extended period.
2. The user has an option to abort the ISSU process by issuing the command "issu abortversion."
Aborting the ISSU process now causes the newly active supervisor (B) to fail over to the standby supervisor (A) running the old image and will also cause the rebooting supervisor (B) to load the original image. The issu acceptversion halts the rollback timer and helps ensure the ISSU process is not automatically aborted during the process.
An example of the CLI for implementing the issu acceptversion command is displayed below:
On the "New" active supervisor, one would issue the following command:
4510R-203#issu acceptversion 2
% Rollback timer stopped. Please issue the commitversion command.
Syntax - issu acceptversion active-slot-number
This is the last stage of the ISSU procedure. Once the user is satisfied with the new version of software, this must be committed by issuing the "issu commitversion" command. This command resets the standby supervisor and boots it with a new version of the software (same as the active supervisor). This concludes the ISSU process, and the new version of software is permanently committed on both supervisors. Since this is the conclusion of the ISSU process, the system can not be reverted back to the previous version of the software from this point onward as a part of this upgrade cycle. However, if for any reason users wish to go back to the previous version of the software, they can do so by starting a new upgrade/downgrade process.
The following actions take place if the command is implemented:
1. The standby supervisor (A) is reset and booted with the new version of Cisco IOS Software image.
2. The standby supervisor (A) moves into the "Standby Hot" state in SSO mode and is fully stateful for all clients/applications that are compatible.
3. Both supervisors are moved into "Final State," which is the same as "Initial State."
4. Users can initiate switchovers from this point onward.
An example of the CLI for implementing the issu commitversion command is displayed below:
4510R-203#issu commitversion 1
Syntax - issu commitversion standby-slot-number
ISSU Process: issu abortversion
One can abort the ISSU process at any stage manually (prior to issuing the issu commitversion command) by issuing the exec-level issu abortversion command. The ISSU process also aborts on its own if the software detects a failure.
If a user aborts the process after issuing the issu loadversion command, then the standby supervisor engine is reset and reloaded with the original software.
If the process is aborted after a user enters either the issu runversion or issu acceptversion command, then a second switchover is performed to the new standby supervisor engine that is still running the original software version.
The supervisor engine that had been running the new software is reset and reloaded with the original software version. The command is accepted only in "Load Version" or "Run Version" states. In "Load Version" state, the active supervisor is running an old image and the standby supervisor is running new image.
Syntax - issu abortversion active-slot [active-image-new]
Let me know if you have any questions.

Anomalies found when downgrade ASR 9K IOS XR 4.3.0 to 4.2.1

Hai,
I have problem when downgrade ASR 9K IOS XR version 4.3.0 to version 4.2.1 on RSP 440
This is the capture :
RP/0/RSP0/CPU0:PE3-D2-JT2-VPN(admin)#sh instal active summary
Wed Apr 17 22:42:21.303 UTC
Default Profile:
SDRs:
    Owner
Active Packages:
    disk0:asr9k-mini-px-4.3.0
    disk0:asr9k-k9sec-px-4.3.0
RP/0/RSP0/CPU0:PE3-D2-JT2-VPN(admin)#
then this is capture after upgrading proces :
RP/0/RSP0/CPU0:PE3-D2-JT2-VPN#show install active summary
Thu Apr 18 02:14:29.457 UTC
Active Packages:
    disk0:asr9k-services-p-px-4.2.1
    disk0:asr9k-mini-px-4.2.1
    disk0:asr9k-doc-px-4.2.1
    disk0:asr9k-k9sec-px-4.2.1
    disk0:asr9k-mpls-px-4.2.1
    disk0:asr9k-mgbl-px-4.2.1
    disk0:asr9k-mcast-px-4.2.1
    disk0:asr9k-fpd-px-4.2.1
RP/0/RSP0/CPU0:PE3-D2-JT2-VPN#admin
Thu Apr 18 02:14:37.632 UTC
RP/0/RSP0/CPU0:PE3-D2-JT2-VPN(admin)#show install inactive summary
Thu Apr 18 02:14:42.139 UTC
Default Profile:
SDRs:
    Owner
Inactive Packages:
    disk0:asr9k-mini-px-4.3.0
    disk0:asr9k-k9sec-px-4.3.0
RP/0/RSP0/CPU0:PE3-D2-JT2-VPN(admin)#
when i verify packages, there are anomalies found
RP/0/RSP0/CPU0:PE3-D2-JT2-VPN(admin)#install verify packages
Thu Apr 18 02:17:07.973 UTC
Install operation 29 '(admin) install verify packages' started by user 'cisco'
via CLI at 02:17:08 UTC Thu Apr 18 2013.
The install operation will continue asynchronously.
RP/0/RSP0/CPU0:PE3-D2-JT2-VPN(admin)#Info:     This operation can take up to 2 minutes per package being verified.
Info:     Please be patient.
Info:     0/4/CPU0 [LC] [SDR: Owner]
Info:         meta-data: [SUCCESS] Verification Successful.
----output omitted--------
Info:         /install/asr9k-base-4.2.1: [SUCCESS] Verification Successful.
Info:     0/RSP1/CPU0 [RP] [SDR: Owner]
Info:         meta-data: [ERROR] Detected anomalies.
Info:         /install/iosxr-infra-4.2.1/instdb/component.db: exists with
Info:     unexpected file size.
----output omitted--------
Info:         0/4/CPU0: SUCCESSFUL. No anomalies found.
Info:         0/0/CPU0: SUCCESSFUL. No anomalies found.
Info:         0/7/CPU0: SUCCESSFUL. No anomalies found.
Info:         0/RSP1/CPU0: Too many anomalies found.
Info:         0/RSP0/CPU0: Too many anomalies found.
Info:         Anomalies found on both the RPs.
Info:         Please contact your technical services representative to repair
Info:     the system.
Install operation 29 completed successfully at 02:18:16 UTC Thu Apr 18 2013.
RP/0/RSP0/CPU0:PE3-D2-JT2-VPN(admin)#RP/0/RSP0/CPU0:Apr 18 02:18:56.272 : canb-server[150]: %PLATFORM-CANB_SERVER-3-MESSAGE_FAILED : Unexpected CBC message received from slot 0/4/CPU0 [ver 20.115] for msg type 3, id 105, len 8
RP/0/RSP0/CPU0:Apr 18 02:23:04.937 : ifmgr[245]: %PKT_INFRA-LINK-3-UPDOWN : Interface MgmtEth0/RSP0/CPU0/1, changed state to Down
RP/0/RSP0/CPU0:PE3-D2-JT2-VPN(admin)#
I did rollback and reinstall, and issue still same.
Anyone please help me.
Thanks

Hi,
We can try to fix the anomalies with a package repair operation or by restarting the instdir process. Please try the repair option first.
' admin install verify packages repair'
Or
'process restart instdir'
Restarting the above process has no service impact on the router.
Let me know the result of trying the above steps.
Thanks,
Sam Milstead
CSE - XR TAC

ASR 1001 OTV Port-Channel

I saw in the release notes that 3.10 for the ASR 1001 supports port-channel for the internal otv interface. I upgraded to that release and it lets me use a port-channel interface, but it won't let me use the serivce instance command on the L2 interface. I can add the channel-group command but not any otv commands. Has anyone seen this yet?
Thanks,
Tom

Hi tom,
Not sure if you have resolved this issue, but, I hope you are configuring the port-channel with all the service-instance configurations. If yes, and you are getting into issues, please do post the output of the issue, we can have a look at the same.

ASR 1001 IOS upgrade issue

Similar Messages

Maybe you are looking for