ASR 1001 Router enquiry on fiber handoff
Cisco ASR 1001 Router would support fiber hand-off of the link. Below is the Specifications of the Router - we received from vendor:
Description
Quantity
Cisco ASR1001 System,Crypto, 4 built-in GE, Dual P/S
1
Cisco 5-Port Gigabit Ethernet Shared Port Adapter
1
1000BASE-LX/LH SFP transceiver module, MMF/SMF, 1310nm, DOM
2
Cisco ASR1001 AC Power Supply
2
Power Cord India, Right Angle
2
Cisco ASR 1001 IOS XE UNIVERSAL - NO ENCRYPTION
1
Cisco ASR 1000 IP BASE License
1
SPA for ASR1000; No Physical Part; For Tracking Only
1
Cisco ASR1001 4GB DRAM
1
PRTNR SS 8X5XNBD Cisco ASR1001 System,Crypto
1
PRTNR SS 8X5XNBD Cisco ASR 1000 IP BASE License
1
PRTNR SS 8X5XNBD 5-Pt Gigabit Enet Shared Pt Adptr
1
Datacenter feature: There will be fiber connections already installed at the DMZ site from the meet me telco room to the partner racks. Therefore, your service provider must understand that they will do a circuit handoff to fiber and order the routers, interface cards, connectors, etc. to support fiber circuit extension.
You can use standard Ethernet copper or Fiber, providing that you have the correct SFP/GBICs.
As long as you have the correct SFP's you need for the ASR - All should be good.
http://www.cisco.com/en/US/docs/interfaces_modules/shared_port_adapters/install_upgrade/ASR1000/ASRintro.html#wp1235447
http://www.cisco.com/en/US/prod/collateral/modules/ps5455/ps6577/product_data_sheet0900aecd8033f885.html
hth
Similar Messages
-
Traffic policing question on Cisco ASR 1001
Hi Experts,
I have a request to setup aggregated traffic policing on a Cisco ASR 1001 router for multiple networks within a router.
Lets say I have a router with several subinterfaces:
interface GigabitEthernet0/2
description WAN
ip address x.x.x.x x.x.x.x
interface GigabitEthernet0/1.70
description Lan_1
encapsulation dot1Q 70
ip address 192.168.55.1 255.255.255.0
interface GigabitEthernet0/1.80
description LAN_2
encapsulation dot1Q 80
ip address 192.168.56.1 255.255.255.0
interface GigabitEthernet0/1.90
description Servers
encapsulation dot1Q 90
ip address 172.16.10.1 255.255.255.0
I have a WAN link 100Mbit/s and I need to police traffic, so that I have 30Mbit/s for servers (GigabitEthernet0/1.90) and the rest 70Mbit I want to share between Interface Lan_1 and LAN_2. The Idea is that I need 70Mbit/s equally shared between two interfaces, so that I have fair policing on both iunterfaces. What is the best way to achieve this?
Many ThanksHello
The below configuration is a possible option, Its provides policing inbound from the clients interfaces and LLQ priority queung on the wan interface for the servers and shaping values from LAN1 & 2 traffic is set to 35MB.each.
Notice nothing is defined for the default class, however i am on the understanding this is given by default 1% of Hqos implementations.
Maybe others on here could review to verify any problems with this post and share their thoughts?
ip access-list extended SRVS_acl
permit ip 172.16.10.0 0.0.0.255 any
ip access-list extended LAN1_acl
permit ip 192.168.55.0 0.0.0.255 any
ip access-list extended LAN2_acl
permit ip 192.168.56.0 0.0.0.255 any
class-map match-all SRVS_CM
match access-group name SRVS_acl
class-map match-all LAN_1_CM
match access-group name LAN1_acl
class-map match-all LAN_2_CM
match access-group name LAN2_acl
policy-map SRVS_PM
class SRVS_CM
police 30720000 conform-action transmit exceed-action drop
policy-map LAN_2_PM
class LAN_2_CM
police 35840000 conform-action transmit
policy-map LAN_1_PM
class LAN_1_CM
police 35840000 conform-action transmit
interface GigabitEthernet0/1.70
service-policy input LAN_1_PM
interface GigabitEthernet0/1.90
service-policy input SRVS_PM
interface GigabitEthernet0/1.80
service-policy input LAN_2_PM
policy-map WAN_CHILD
class SRVS_CM
priority 30720
class LAN_1_CM
shape average 35840000
class LAN_2_CM
shape average 35840000
class class-default
fair-queue
policy-map WAN_PARENT
class class-default
shape average 102400000
service-policy WAN_CHILD
int GigabitEthernet0/2
bandwidth 102400
service-policy output WAN_PARENT
res
Paul -
What Software image / License required for ASR 1001
Hi,
I want to purchase Cisco ASR 1001 router, I need to run ssh , Crypto , IPSec VPN ( 3DES, ESP ) and Gre Tunnels on it.
i am confused with different IOS / Licenses of ASR 1001, can any one please suggest me with the part numbers that i need to put in for ordering ?
From my Vendor quote i can see that below is the part of the packege ( part number = ASR1001 )
SASR1001UK9
Cisco ASR1001 IOS XE - ENCRYPTION UNIVERSAL
but there is another Technology based license required and this is not included in the above part number packet so i need to know which one i need to buy from below?
ASR1001/ASR 1002-X Technology Package Licenses
SLASR1-IPB
Cisco ASR 1000 IP BASE License
SLASR1-AIS
Cisco ASR 1000 Advanced IP Services License
SLASR1-AES
Cisco ASR 1000 Advanced Enterprise Services License
SLASR1-IPB=
Cisco ASR 1000 IP BASE Paper PAK
L-SLASR1-IPB
Cisco ASR 1000 IP BASE E-Delivery PAKThere was a regression introduced in 3.5.1 where the Main-class attribute of the Coherence.jar was changed to a different main class leading to this effect.
The workaround is to specify the main class as part of the command line.
Assuming your current directory is the coherence home directory:
Start a cache server:
java -cp lib/coherence.jar com.tangosol.net.DefaultCacheServer Start the command line:
java -cp lib/coherence.jar com.tangosol.coherence.component.application.Console And the above is basically what the coherence.sh/.cmd and cache-server.sh/.cmd scripts do.
Edited by: Christer Fahlgren on Aug 31, 2009 10:06 AM -
I am working on putting a loaner ASR 1001 into my infrastructure to replace my 7206 VXR. Currently my uplink to my ISP is fiber and runs into an GBIC SX MM transceiver. No issue with connectivity. When i change the fiber patch over to LC I connect it to the ASR 1001 GBIC and I get no link. Tried changed negotiation auto to no negotiation auto not affect. I then took the fiber and connected to a gbic I have in a 3560 switch link comes right up. At this point I am a bit stumped. Tried moving the configuration to a different interface on the ASR no luck. Totally confused.
What model transceiver are you using on the ASR? I didn't tink they took GBICs - ony SFPs. I think the one you would need is an SFP (the GLC-SX-MMD or GLC-SX-MM without DOM). That's what's compatible on an ASR 1001 for 1 Gbps MM fiber per the compatibility matrix.
Is the ASR recognizing the transceiver? (show int ___) -
ASR 1001 L2TP sessions // License issue?
Hello,
This is my first post, in the fisrt place, sorry for my english, is not my native language.
I have purchased a refurbished ASR 1001 without any license for using as LNS:
Cisco IOS XE Software, Version 03.12.00.S - Standard Support Release
Cisco IOS Software, ASR1000 Software (X86_64_LINUX_IOSD-UNIVERSALK9-M), Version 15.4(2)S, RELEASE SOFTWARE (fc2)
asr1001-universalk9.03.12.00.S.154-2.S-std.bin
The scenario is this:
LAC (from network provider) send L2TP packet sessions-> LNS (ASR 1001, assign public IP to user and close the L2TP session).
The configuration of ASR is the typical for xDSL connections.
1) The LAC send requests to LNS Loopback interface:
interface Loopbacktest1
ip address 5.6.7.8 255.255.255.255
snmp ifindex persist
2) LNS assign the loopback interface to vpdn group, that points to virtual-template:
vpdn-group VpdnG1
accept-dialin
protocol l2tp
virtual-template 1
terminate-from hostname Provider01
dsl-line-info-forwarding
source-ip 5.6.7.8
lcp renegotiation always
l2tp tunnel password 7 XXXXXXXX
interface Virtual-Template1
description Int-Vi1 VpdnG1
mtu 1501
ip unnumbered GigabitEthernetX/X/X
ip mtu 1460
ip tcp adjust-mss 1400
no peer default ip address
ppp max-terminate 255
ppp max-configure 255
ppp max-failure 255
ppp max-bad-auth 10
ppp authentication pap chap ppp_authent2
ppp multilink
Since here, all is OK, but the problem is that the ASR cannot reach connected users and evidently the user doesn't have internet connectivity because he cannot reach the gateway IP (ASR IP).
Interface User Mode Idle Peer Address
Vi1.1 test1 PPPoVPDN - 1.2.3.4
L2TP Tunnel and Session Information Total tunnels 1 sessions 1
LocTunID RemTunID Remote Name State Remote Address Sessn L2TP Class/
Count VPDN Group
1589 3324 Provider01 est 5.6.7.8 1 VpdnG1
ASR1001#ping 1.2.3.4
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 1.2.3.4, timeout is 2 seconds:
Success rate is 0 percent (0/5)
ASR1001 in not forwardinf the traffic to end users
Exactly the same configuration works fine in 7201 cisco router.
After read some information in internet and cisco web and test several IOS images and configurations I have activated 2 of 3 (marked in bold down) possible licenses that are available to test in the router (these are available during 60 days).
SLASR1-IPB
Cisco ASR 1000 IP BASE License
SLASR1-AIS
Cisco ASR 1000 Advanced IP Services License
SLASR1-AES
Cisco ASR 1000 Advanced Enterprise Services License
***Result-> After apply Advanced IP Service or Advanced Enterprise license the ASR works perfectly, forwarding the traffic to the end users. The router can reach gateway and have internet connection.
I would like to try IP BASE License but there is no possibility to activate the test period in the router, I don't know if you knows any way to test it. This is the details that router shows about this 3 license types:
Index 1 Feature: adventerprise
Period left: 8 weeks 1 day
Period Used: 2 days 12 hours
License Type: EvalRightToUse
License State: Active, In Use
License Count: Non-Counted
License Priority: Low
Index 2 Feature: advipservices
Period left: Not Activated
Period Used: 0 minute 0 second
License Type: EvalRightToUse
License State: Active, Not in Use, EULA not accepted
License Count: Non-Counted
License Priority: None
Index 3 Feature: ipbase
-->There is no more info about IP base license<---
If I use the command "license boot level" I can apply the IP base license, but after reload the router, nothing happens.
ASR1001(config)#license boot level ?
adventerprise Advanced Enterprise License Level
advipservices Advanced IP Services License Level
ipbase IP Base License Level
Then my answers are:
1) Is 100% necessary to have a license in ASR1001 to use the router as LNS as showed? Apparently after my tests I will answer "yes", but I'm not sure if my configuration is the only one that I can configure. Maybe exist another way to config the required scenario and avoid the purchase license.
2) Do you know if IP Base license will active the forwarding packet function in the ASR? I think yes, but before buy this license I need to be sure. As you know Ip Base is the most cheap license.
Thanks in advantage!
RegardsHello,
Documentation states that licensing on the ASR 1000 are now honor-based since 3.7s. I didn't test it though.
Basically, your license marked now as "EvalRTU" will be moved to an "RTU" license, indicating you would need to buy a license to keep your honor intact, but no disruption in features or connectivity will happen.
Since your test was more than 60 days ago, can you confirm this behavior with 3.12 ?
Thanks,
Kind regards,
Sources:
- All Cisco ASR 1000 feature and performance upgrade licenses are honor-based; that is, they are not enforced through a PAK (Product Activation Key). Note: Prior to Cisco IOS XE Software Release 3.7S, performance upgrade licenses that are required to upgrade the Cisco ASR 1001 from 2.5 to 5 Gbps or the Cisco ASR 1002-X from 5 to 10 to 20 to 36 Gbps are enforced through a PAK. Similarly, prior to Cisco IOS XE Software Release 3.6S, technology package licenses are enforced through a PAK. [1]
- When the 60-Day Evaluation Period expires, the license automatically changes to an RTU license. As with all other RTU licenses, there is no functionality disruption or accessibility concerns following this transition. [2]
[1] http://www.cisco.com/c/en/us/products/collateral/routers/asr-1000-series-aggregation-services-routers/guide-c07-731639.html
[2] http://www.cisco.com/c/en/us/td/docs/routers/asr1000/install/guide/1001-x/asr1hig/asr1lic.html -
Hi I am changing IOS of Cisco ASR 1001 from asr1001-universalk9.03.07.02.S.152-4.S2.bin
to asr1000rp1-adventerprisek9.03.04.02.S.151-3.S2.bin but everty time it boot up with old IOS universalk9.
Is it becaused of Licence issue.
Router#sh bootvar
BOOT variable = bootflash:asr1000rp1-adventerprisek9.03.04.02.S.151-3.S2.bin,12;bootflash:asr1001-universalk9.03.07.02.S.152-4.S2.bin,12;
CONFIG_FILE variable does not exist
BOOTLDR variable does not exist
Configuration register is 0x2102
License Level: advipservices
License Type: Permanent
Next reload license Level: advipservices
cisco ASR1001 (1RU) processor with 1155941K/6147K bytes of memory.
Processor board ID SSI1607042B
4 Gigabit Ethernet interfaces
32768K bytes of non-volatile configuration memory.
4194304K bytes of physical memory.
7741439K bytes of eUSB flash at bootflash:.
Configuration register is 0x2102You downloaded the wrong file. The file you wanted to run has "rp1" but the original file doesn't. You downloaded a file for a different model. Your router is an ASR 1001 with fixed RP but you've downloaded a file for a different sub-model of ASR, like the 1002 or 1004.
Go here instead: http://software.cisco.com/download/release.html?mdfid=282993672&softwareid=282046477&release=3.10.3S&relind=AVAILABLE&rellifecycle=ED&reltype=latest -
Hi Cisco Professional,
We want to implementing PPPoE over port-channel (using subinterfaces L2) in Cisco ASR 1001 routers, my question is if this router support this feature?, in the other hand i've see documents about this theme, pls check these links:
http://www.cisco.com/en/US/docs/ios/ios_xe/cether/configuration/guide/ce_lnkbndl_xe.html
http://www.cisco.com/en/US/docs/ios-xml/ios/cether/configuration/xe-3s/ce-ieee-link-bndl-xe.html
My IOS version Cisco ASR 1001 is:
System image file is "bootflash:/asr1001-universalk9.03.04.00.S.151-3.S.bin"
We want this configuration on the router,
no interface GigabitEthernet0/0/0.25
interface port-channel 10.25
description TURBONETT PUBLICA UT
encapsulation dot1Q 25
ip address 10.17.44.254 255.255.252.0
no interface GigabitEthernet0/0/0.52
interface port-channel 10.52
description TURBONETT-UT
encapsulation dot1Q 52
pppoe enable group global
pppoe max-sessions 4000
no interface GigabitEthernet0/0/0.61
interface port-channel 10.61
description Turbonett-Sector-A
encapsulation dot1Q 61
pppoe enable group global
pppoe max-sessions 4000
Kind Regards,
Renzo TovarHi Renzo,
PPPoEoVLAN on GEC (LACP mode) is supported as of XE 3.7. I see that you are using XE 3.4 here so I would suggest to move to XE 3.7 and try this feature.
This is a sample configuration for the feature:
interface GigabitEthernet2/1/0
no ip address
negotiation auto
channel-group 2 mode active
interface GigabitEthernet3/1/0
no ip address
negotiation auto
channel-group 2 mode active
lacp port-priority 65000
interface Port-channel2
no ip address
load-interval 30
no negotiation auto
lacp max-bundle 1
lacp fast-switchover
interface Port-channel2.200
encapsulation dot1Q 200
pppoe enable group global
interface Port-channel2.500
encapsulation dot1Q 500 second-dot1q 1500
pppoe enable group global
As you can see, both PPPoEoVLAN and PPPoEoQinQ are supported.
Hope this helps.
Best regards. -
10GE port adapter in ASR 1001 chassis
Dear All,
Will SPA-1X10GE-L-V2 work in ASR 1001 chassis with the integrated ESP and SIP?
Thx,
SzilardYou are most welcome, szilard.matayas1. Thanks for the rating as well.
Are you already working with a Cisco partner/rep for this requirement as well? Let me know if you need assistance on that department as I can check on SPA-1X10GE-L-V2 availability as well. Do send me an e-mail ([email protected]). Kind regards. -
I saw in the release notes that 3.10 for the ASR 1001 supports port-channel for the internal otv interface. I upgraded to that release and it lets me use a port-channel interface, but it won't let me use the serivce instance command on the L2 interface. I can add the channel-group command but not any otv commands. Has anyone seen this yet?
Thanks,
TomHi tom,
Not sure if you have resolved this issue, but, I hope you are configuring the port-channel with all the service-instance configurations. If yes, and you are getting into issues, please do post the output of the issue, we can have a look at the same. -
Thanks in advance for your help!
what license do I need to create a IPSEC tunnel?
I have an ASR 1001, running ?
System returned to ROM by reload at 10:14:31 UTC Tue Aug 23 2011
System image file is "bootflash:asr1001-universalk9_npe.03.03.00.S.151-2.S.bin"
Last reload reason: PowerOn
License Info:
License UDI:
Device# PID SN UDI
*0 ASR1001 JAE153402YI ASR1001:JAE153402YI
License Package Information for Module:'asr1001'
Module name Image level Pri Config Valid license
asr1001 adventerprise 1 NO adventerprise
advipservices 2 NO advipservices
ipbase 3 NO ipbase
Module name Current Level Reboot Level
asr1001 ipbase ipbase
cisco ASR1001 (1RU) processor with 1202026K/6147K bytes of memory.
4 Gigabit Ethernet interfaces
32768K bytes of non-volatile configuration memory.
4194304K bytes of physical memory.
7782399K bytes of eUSB flash at bootflash:.Hi,
You need to have advipservicesk9 bundle in order to configure vpn tunnels.
Please rate the helpfull posts.
Regards,
Naidu. -
Hello, Try as I might I cant find a document that says;
"How to activate encryption on an ASR 1001" or "activating ip advanced features" on the ASR 1001.
Can anyone help please. My Kit list.
Cisco ASR1001 System,Crypto, 4 built-in GE, Dual P/S
Cisco ASR1001 4GB DRAM
Cisco ASR 1000 Advanced IP Services License
Cisco ASR 1001 IOS XE - ENCRYPTION UNIVERSAL
IPSEC License for ASR1000 Series
Upgrade from 2.5 Gbps to 5Gbps License for ASR 1001
Whats the process to activate the 2.5gbps to 5gbps feature or encryption?
Thanks
ChrisChris,
The ASR1000 feature licensing is explained on the document http://www.cisco.com/en/US/prod/collateral/routers/ps9343/product_bulletin_c25-448292.html
You can also find this information on the product datasheet at http://www.cisco.com/en/US/prod/collateral/routers/ps9343/data_sheet_c78-447652.html
Regarding IPSec and Bandwidth licenses on ASR1K, see below and excerpt from datasheet:
Cisco ASR1001 Feature Licenses: Enforced with PAK
FLSASR1001-5G
Upgrade from 2.5 Gbps to 5Gbps License for ASR 1001
FLSASR1001-5G=
Upgrade from 2.5 Gbps to 5Gbps Paper PAK for ASR 1001
L-FLSASR1001-5G=
Upgrade from 2.5 Gbps to 5Gbps E-Delivery PAK for ASR 1001
Security
FLSASR1-IPSEC
IPSEC License for ASR1000 Series
FL-ASR1-IPSEC=
IPSEC Paper PAK for ASR1000 Series
L-FL-ASR1-IPSEC=
IPSEC E-Delivery PAK for ASR1000 Series
Cheers, Gustavo -
Maximum cos1 (voice traffic) supported by Cisco ASR 1006 router
Dear Team,
Please confirm the maximum cos 1 traffic supported by cisco ASR 1006 router.Yes, it would. If you are planning on terminating a single site on this router I would spread over multiple routers for redundancy.
Table 6 explains number of ports and channels providing you have the DSPs:
http://www.cisco.com/c/dam/en/us/products/collateral/routers/2800-series-integrated-services-routers-isr/product_data_sheet0900aecd8057f2e0.pdf -
Hello
I have one Adtran Router on platform: NetVanta 4660 EoX L2/L3 Router having OS version R10.11.0.E. I want to replace this router with Cisco ASR 1002 router. There is EVC configured on Adtran router having the following configuration:
interface gigabit-eth 0/1
speed 1000 nonegotiate
no shutdown
interface gigabit-eth 0/1.2
ce-vlan-id 10
connect evc dolphin
ip address 1.1.1.1 255.255.255.252
no shutdown
interface gigabit-eth 0/1.3
ce-vlan-id 20
connect evc dolphin
ip address 2.2.2.1 255.255.255.252
shutdown
evc dolphin
s-tag 150
connect men-port gigabit-ethernet 0/1
no shutdown
Now we want to configure this type of configuration on ASR 1002. So can anybody help me to achieve this?
Regards
Mukesh Kumar
Network Engineer
Spooster IT ServicesHi
You could try with bridging. Something like this
Interface bvi 1
no ip address
interface gig0
bridge-gropup 1
interface gig1
bridge-group 1
/Mikael -
ASR 1002 Router doing multiple VRFs
I have an ASR 1002 router with Three VRFs coming into it. The first 2 VRFs are just terminating on the ASR with L3 sub interfaces. So no big deal with them. The third one is a VRF that needs to terminate on a separate router. The ASR that needs to split out this 3rd VRF is not allowed to have an IP address for it. So it just needs to forward off this as L2 to a separate physical port and then terminates on a different router.
So my question is what is the best way to accomplish this on the ASR? Could I setup a pseudo wire setup or is there an easier way to just split off this as separate VLAN to the other physical interface?Hi
You could try with bridging. Something like this
Interface bvi 1
no ip address
interface gig0
bridge-gropup 1
interface gig1
bridge-group 1
/Mikael -
Hi Everybody,
I´m making a proposal for a costumer where he needs connect one ASR 1001 with other ASR1001 via UTP cable. The speed will be 100 Mbps at this moment. Can I use the SFP-GE-T tranceiver for a 10/100/1000 Mbps connection ?
Thank you.Disclaimer
The Author of this posting offers the information contained within this posting without consideration and with the reader's understanding that there's no implied or expressed suitability or fitness for any purpose. Information provided is for informational purposes only and should not be construed as rendering professional advice of any kind. Usage of this posting's information is solely at reader's own risk.
Liability Disclaimer
In no event shall Author be liable for any damages whatsoever (including, without limitation, damages for loss of use, data or profit) arising out of the use or inability to use the posting's information even if Author has been advised of the possibility of such damage.
Posting
I believe the copper SFP supports 10/100/1000.
Maybe you are looking for
-
Anyone know who I can file a complaint with about customer service agents giving wrong information
I am a fairly new customer with Verizion and I have been having THEEE WORST time with simply cashing in on a offer that was offered to me! I want to file a complaint on the representatives that have sent me into the store on blank missions and also a
-
Why do I need iPhoto???
it duplicates the photos; doesn't have a god way to see pictures and deleting unwanted (like windows photo viewer - simple and usefull); doesn' import automatecly from iPhone... when importing is in the iPhoto library, we cant easly export to a exter
-
I can't open my emails (i CAN in internet explorer)
when i open email in firefox, i can get to the first page ...it's xfinity/comcast, and it shows a summary of the last ten emails....i try to " view the entire inbox"....the little colored dots go round and round....and then the summary page re-appear
-
Replacing letters through StreamTokenizer
Hi, I am writing a program which reads from a text file, passes it into a StreamTokenizer, looks for a particular word and capitalises the first letter (in this case "apples" to "Apples"). It's all fine, except when the word I'm looking for appears i
-
IMovie not opening. Error 1712
I updated iMovie last night to iMovie 10.0.3 from iMovie 09. It took all night to download. When I opened it this morning it was working well and then I closed the app. When I tried to open it again, the grey bar at the top changed to iMovie but the