ASR 1002 Monitor Session doesn't works.

Hello,
I am trying to configure a monitor session in a Cisco ASR1002 but it doesn't works (sniffer is on interface gigabitEthernet 0/0/3).
My config is:
monitor session 10 type local
source interface GigabitEthernet0/0/0
destination interface GigabitEthernet0/0/3
and interfaces are up:
#show interfaces GigabitEthernet0/0/0
GigabitEthernet0/0/0 is up, line protocol is up
5 minute input rate 241240000 bits/sec, 26651 packets/sec
5 minute output rate 4000 bits/sec, 6 packets/sec
#sh interfaces gigabitEthernet 0/0/3
GigabitEthernet0/0/3 is up, line protocol is up (monitoring)
5 minute input rate 0 bits/sec, 0 packets/sec
5 minute output rate 0 bits/sec, 0 packets/sec
Is very urgent for me so any help would be very appreciated.
Thanks in advance for your help.
Regards.
Ruben.

Hello,
Please see below.
http://www.cisco.com/c/en/us/td/docs/ios-xml/ios/lanswitch/configuration/xe-3s/asr1000/lanswitch-xe-3s-asr1000-book/lnsw-conf-erspan.html#GUID-152D9875-169B-461F-A34B-ABAABD0C1FF8
"The monitor session span-session-number type local command is not supported on Cisco ASR 1000 Series Routers."
===You may though configure ERSPAN to work as a local SPAN===
* Make sure that both the source session and destination session have the same erspan-id
* Use one locally configured IPv4 address to configure the "ip address" and "origin ip address" in source session and "ip address" in destination session
Example snip: Monitor interface Gig0/0/0 traffic, and then send out through interface Gig0/0/1..
monitor session 10 type erspan-source
source interface Gi0/0/0
destination
erspan-id 10
ip address 10.10.10.1
origin ip address 10.10.10.1
monitor session 20 type erspan-destination
destination interface Gi0/0/1
source
erspan-id 10
ip address 10.10.10.1

Similar Messages

ASR 1002 Monitor

I have an ASR 1002 that I have placed the following config on:
monitor session 1 type local
source interface Gi0/0/2 , Gi0/3/0
destination interface Gi0/3/4
I am not receiving any traffic on the destination port, is this really supported on the ASR?

Hello,
Please see below.
http://www.cisco.com/c/en/us/td/docs/ios-xml/ios/lanswitch/configuration/xe-3s/asr1000/lanswitch-xe-3s-asr1000-book/lnsw-conf-erspan.html#GUID-152D9875-169B-461F-A34B-ABAABD0C1FF8
"The monitor session span-session-number type local command is not supported on Cisco ASR 1000 Series Routers."
===You may though configure ERSPAN to work as a local SPAN===
* Make sure that both the source session and destination session have the same erspan-id
* Use one locally configured IPv4 address to configure the "ip address" and "origin ip address" in source session and "ip address" in destination session
Example snip: Monitor interface Gig0/0/0 traffic, and then send out through interface Gig0/0/1..
monitor session 10 type erspan-source
source interface Gi0/0/0
destination
erspan-id 10
ip address 10.10.10.1
origin ip address 10.10.10.1
monitor session 20 type erspan-destination
destination interface Gi0/0/1
source
erspan-id 10
ip address 10.10.10.1

[SOLVED] LXDM not saving selected session,Default session doesn't work

Hello,
I'm trying to use LXDM to start my desktop. However, every single time I log in, I have to tell it to use XFCE as my session.
Even if I choose it manually, after logout/login it just resets to "Default session" (which doesn't work: just drops back to LXDM).
I looked everywhere in my home directory and not found any place where it stores the session.
Any ideas? lxdm 0.4.1-8, xfce 4.8, x86-64 Arch Linux.
Thanks.
Last edited by Renan Birck (2012-04-02 21:06:42)

It's the default, except that I enabled autologin (which doesn't work due to the problem I describe in my post).
[base]
## uncomment and set autologin username to enable autologin
autologin=renan
## uncomment and set timeout to enable timeout autologin,
## the value should >=5
# timeout=10
## default session or desktop used when no systemwide config
# session=/usr/bin/startlxde
## uncomment and set to set numlock on your keyboard
# numlock=0
## set this if you don't want to put xauth file at ~/.Xauthority
# xauth_path=/tmp
## greeter used to welcome the user
greeter=/usr/lib/lxdm/lxdm-greeter-gtk
[server]
## arg used to start xserver, not fully function
# arg=/usr/bin/X -background vt1
[display]
## gtk theme used by greeter
gtk_theme=Clearlooks
## background of the greeter
# bg=/usr/share/backgrounds/default.png
## if show bottom pane
bottom_pane=1
## if show language select control
lang=1
## if show keyboard layout select control
keyboard=0
## the theme of greeter
#theme=Archlinux
[input]
[userlist]
## if disable the user list control at greeter
disable=0
## whitelist user
white=
## blacklist user
black=

Battery monitor 3 doesn't work fine.

Hi,
Recentl I have downloaded battery monitor 3 app from store.
That doesn't work fine as I have to manually touch on it to show the updated remaining average use!
Any ideas?
Thank you.
-------------------If this post helped you, click on accept as solution.------------------
-----------------------------Appreciate by clicking on white star.----------------------------
Solved!
Go to Solution.

It's working fine for me.
I have noticed that it is possible to deselect all the estimates in the main app screen so wonder if that could be your problem. Make sure that at least one icon has a grey background as in the attached grab - 04 selected, 05 deselected.
I don't remember being able to deselect "Average Use" in earlier versions.
N8-00 pc059C9F6 Belle
808 PureView pc059P6W5
Attachments:
Scr000004.jpg ‏70 KB
Scr000005.jpg ‏70 KB

[SOLVED] KDE Start New Session doesn't work from lock screen

On my laptop, if I lock the KDE 4 session and then click Switch Users > Start New Session, I get a login screen and can log in as a different user. All good.
If I do the same thing on my desktop, it doesn't work. When I click Switch Users > Start New Session, it doesn't start a new session or switch VTs. Instead, I just get reprompted for the existing user's password.
Both machines are running fully updated Arch. Anyone know how I can troubleshoot this? The only difference I can think of between the laptop and desktop is that the desktop has nomodeset specified as a kernel boot parameter. (It won't boot without it.) Could this be interfering with automatic VT switching? Manual VT switching (e.g. Ctrl+Alt+F1) works fine.
Last edited by Rob_H (2014-12-27 14:28:06)

Little more detail. Checking the journal, I can see Xorg is failing to start on display :1. If I compare Xorg.0.log with Xorg.1.log, it appears that it's not finding the proprietary NVIDIA driver in the second case. Don't know why it would be any different for :1, though. See?
Xorg.0.log (good):
[ 10.219] (II) LoadModule: "glx"
[ 10.220] (II) Loading /usr/lib/xorg/modules/extensions/libglx.so
[ 10.293] (II) Module glx: vendor="NVIDIA Corporation"
[ 10.293] compiled for 4.0.2, module version = 1.0.0
[ 10.293] Module class: X.Org Server Extension
[ 10.294] (II) NVIDIA GLX Module 343.36 Mon Dec 1 15:50:02 PST 2014
[ 10.294] (II) Applying OutputClass "nvidia" to /dev/dri/card0
[ 10.294] loading driver: nvidia
[ 10.294] (==) Matched nvidia as autoconfigured driver 0
[ 10.294] (==) Matched nouveau as autoconfigured driver 1
[ 10.294] (==) Matched nv as autoconfigured driver 2
[ 10.294] (==) Matched nouveau as autoconfigured driver 3
[ 10.294] (==) Matched nv as autoconfigured driver 4
[ 10.294] (==) Matched modesetting as autoconfigured driver 5
[ 10.294] (==) Matched fbdev as autoconfigured driver 6
[ 10.294] (==) Matched vesa as autoconfigured driver 7
[ 10.294] (==) Assigned the driver to the xf86ConfigLayout
[ 10.294] (II) LoadModule: "nvidia"
[ 10.294] (II) Loading /usr/lib/xorg/modules/drivers/nvidia_drv.so
[ 10.300] (II) Module nvidia: vendor="NVIDIA Corporation"
[ 10.300] compiled for 4.0.2, module version = 1.0.0
[ 10.300] Module class: X.Org Video Driver
Xorg.1.log (bad):
[ 2153.825] (II) LoadModule: "glx"
[ 2153.825] (II) Loading /usr/lib/xorg/modules/extensions/libglx.so
[ 2153.833] (II) Module glx: vendor="NVIDIA Corporation"
[ 2153.833] compiled for 4.0.2, module version = 1.0.0
[ 2153.833] Module class: X.Org Server Extension
[ 2153.833] (II) NVIDIA GLX Module 343.36 Mon Dec 1 15:50:02 PST 2014
[ 2153.833] (==) Matched nouveau as autoconfigured driver 0
[ 2153.833] (==) Matched nv as autoconfigured driver 1
[ 2153.833] (==) Matched modesetting as autoconfigured driver 2
[ 2153.833] (==) Matched fbdev as autoconfigured driver 3
[ 2153.833] (==) Matched vesa as autoconfigured driver 4
[ 2153.833] (==) Assigned the driver to the xf86ConfigLayout
[ 2153.833] (II) LoadModule: "nouveau"
[ 2153.833] (WW) Warning, couldn't open module nouveau
Any idea what would cause it to work for :0 but fail for :1?

Ck-launch-session gnome-session doesn't work

I go
ck-launch-session gnome-session
I'm told
** (gnome-session:3792): WARNING **: Cannot open display:
What's going on? Why doesn't it work.

@falconindy
Fair enough. I'll see what I can do. Now if only there was more understandable documentation I wouldn't have this problem.
Also what is your take on the following related problem?
https://bbs.archlinux.org/viewtopic.php?id=111804

Mac: Full screen on dual monitors still doesn't work with Flash 10.2 upgrade

Recently upgraded to Flash 10.2 specifically for the ability to work on a second monitor while watching fullscreen video on the first. It's still not working at all. The second I click on anything on the second screen, the video jumps back from full screen. I checked to make sure that these sites work properly with dual monitors on a Windows machine. Any tips to get this working? Without this feature, certain websites are completely useless.
Running: MAC 10,2,152,33 on OSX 10.6.6

Hi, I think you are right about it being in this latest FP update. The "More like This" feature on the right hand side of the threads is not working. I think I have some info on Full Screen, but not the dual monitor issue. I'll check to be sure.
I'll try to find some info on it. There were so many changes that came out with this last update.
Will get back to you when I find the info.
Thanks,
eidnolb

[solved] GNOME cpu frequency scaling monitor applet doesn't work

Hello,
i have installed everything successfully (i come from fedora), but now i have a problem
I want to add the cpu frequency scaling monitor applet to the panel, but i can't see it. When i rightclick on this place, the submenu with settings and so on is displayed, and i can choose the other cpu1 instead of cpu0, then the applet appears. But the applet shows 0 Mhz and i can't choose a frequency or something.
I start GNOME with xinit and have added exec ck-launch-session gnome-session to ~/.xinitrc, because shutdown wasn't displayed at the beginning and automouting permission problems.
What's the problem?
Edit: My system is a netbook with intel atom cpu
Last edited by scenox (2010-07-19 18:11:59)

the problem is that the modules are not loaded automatically for cpu scaling and you have to explicity add them into rc.conf, MODULES array.
MODULES=(...acpi-cpufreq cpufreq_ondemand...)

5.0 update lost all my tabs, restore previous session doesn't work

This update really ticks me off. I was upgraded to version 5 without any warning and all my tabs are gone. They had all my logins on them and there are too many to remember. What the *^%^*&(*)()(*&. How can I restore back to version 4 and my tabs.

If you are in the profile manager then that is probably your problem, starting a new profile would be devoid of your old information. You have to find the profile you had before the problem, and use it (or copy it into your new profile, if you are beta testing and need to use multiple profiles) . Generally anything you do in a profile must be done with Firefox down. If what you are looking at looks like the picture in
* http://kb.mozillazine.org/Profile_Manager
but more than just default, first find the correct profile you need by find the profile used until the date of the problem, check each profile for the last modified dates for places.sqlite and the .json files in bookmarkbackups in your profiles.
Since you are on Windows 7 as am I, you can get there by inserting your username that you log in to Windows with. The foldername in the Profiles directory includes the profilename plus additional characters to prevent two profiles from every having the same name on your system.
C:\Users\''<userid>''\AppData\Roaming\Mozilla\Firefox\Profiles\
When you identify the correct profile, choose that profile name in the profile manager, then click on "Start Firefox". Never delete any profiles unless you are sure of what you are doing and have a backup of everything on an external device.
You can add the profile to your Desktop or Quick Launch button so you won't be asked, once you are working properly.
* http://kb.mozillazine.org/Profile_Manager#Shortcut_to_a_specific_profile
Some information on how I set up my Windows 7
*http://dmcritchie.mvps.org/windows-7/win7.htm

Friendly for iPad chat session doesn't work

I tried to login to chat from friendly, and it requested my password. When I enter it, it gives an error as if the password is wrong. Is it an issue with new friendly version, or compatibility with IOS 5 ? Any ideas?

There are no restrictions on dual orientation folio creation in Creative Cloud. It's probably that your folio wasn't explicitly created as dual-orientation to start with, or your device is orientation locked.
Neil

I cannot use any external monitor, it appear like the port doesn't work , i'm using the mini-dvi port with a VGA adaptor ,

I've always used the port normally with different monitor but by a couple of weeks it appear like no signal come out.
Does Anyone knows what can i do ? i.e. How to check or reset the Mini-dvi port ? or if there's any key on the keyboard that can habilitate it or not ?
Any Help will be appreciate
Thanks

Welcome to Apple Support Communities
You don't have to do anything to make the port work. Reset the SMC > http://support.apple.com/kb/HT3964
If it doesn't work, try with another monitor to see if it works or another cable. If you haven't got another display, take the MacBook Pro to an Apple Store or reseller, so Apple will test the port and see if it works correctly

DVI to HDMI doesn't work with Panasonic Monitor

Hi all,
I have a Panasonic monitor, model TH-50PX75U that we've used with my Macbook Pro. I have an DVI (large style) to HDMI cable that we connect the Macbook with, and it works fine.
I also have a MacPro that I want to use this monitor with. It has 1 full size DVI display port and 2 mini display ports. In the past I've used the DVI and one mini port to connect 2 monitors at once one the MacPro and it has worked fine.
I tried connecting the Panasonic monitor to use on my mid 2012 MacPro but I never get a picture. I reconnected one of the other monitors to a mini dispplay port and can see that the MacPro recognizes the Panasonic monitor. Both monitors show up in the Display section under System Preferences. I've tries various settings for the Panasionic monitor but I can never get anything to display on it.
What am I missing here? The MacPro is a mid 2012 with 3.2Gig Quad Core / 6 Gig ram / Radion 5770 graphic card, and runs ML 10.8.3.
Any advise is appreciated.
Thanks!
Ray

Ok, so I had time to do some testing and here's what I've done:
I plugged in my Macbook which does work on the Pana monitor, and looked at the Profile. I then compared it to the Profile on the Mac Pro. There are some differences which I'm guessing have to do with different HW. I'm going to include some photos of the working and not working monitor scenarios do you can see what I'm seeing.
Does anyone have any suggestions as to how to make this work?
Photo1: Shows the Macbook and the Pana monitor together using DVI to HDMI cable to connect the two.
Photo2: Shows the display settings with the small monitor and Pana connected to Mac Pro. Notice there are no numbers in the diplays. Mirroring them doesn't work either. The small monitor is using a DVI to mini port adapter to connect to the graphics card, the Pana is using an HDMI to DVI cable (same one I used with the Macbook) to connect to the DVI port of the graphics card.
Photo3: Both monitors are on. The Mac Pro knows the Panasonic is there but I never get a display on it.
Message was edited by: Rayzorx

I am trying to sign in to attend a session and it says 'Invalid user or password. Please try again.' I have reset my password and it still doesn't work. I created a new AdobeID and it still doesn't work. I need to attend this training. How can I get in?

I am trying to sign in to attend a session and it says 'Invalid user or password. Please try again.' I have reset my password and it still doesn't work. I created a new AdobeID and it still doesn't work. I need to attend this training. How can I get in?

Sorry to hear about this problem. What site are you trying to log in on? Is it a Mozilla site? Usually you don't need to register or sign in to a Mozilla site to use Firefox. Usually you can just go straight to where you want to go.

RD Session Broker + NLB doesn't work for external users (internal users on network/WAN are OK)

Hi all,
I have run into an issue as the title of this question suggests.
So the senario is, I have (all Virtual):
2x 2008 R2 Remote Desktop Servers
1x 2008 R2 with Session Broker install
I haven't configured any RD settings on the session broker server (i.e. RD virtual desktop, RD Gateway, etc) It's purely setup as the RD Connection Broker
Each of the RD servers I have configured 2 NIC's. The 1st NIC is configured with NLB (NLB only setup for traffic on port 3389 all other traffic isn't handled by NLB). The other NIC is configured to be used only for session reconnection. I'm hoping this is
the right configuration as it's how I have interpreted these guides:
http://technet.microsoft.com/en-us/library/cc772418%28WS.10%29.aspx
http://technet.microsoft.com/en-us/library/cc771300%28WS.10%29.aspx
Please correct me if I have setup the servers incorrectly and what should be differently.
I have setup the NLBs Cluster IP. A rule has been set on the router to make it available externally
This worked fine with an old single RD Server (same IP as NLB Cluster IP, currently offline so no conflict) before the RD Farm was implemented. So I know the port forwarding is OK.
So NLB and Connection Broker Load-Balancing work well for users inside the network. It spreads sessions evenly and there is no problem with DNS resolving the farm name etc. Sessions that are disconnected are reconnected to the same server, etc.
Accessing the TS Farm from the external address isn't so successful
Connectivity is random. Rarely it works, sometimes it gets to "initiating remote connection..." and then disconnects. It doesn't work more times than it does.
So what do I need to do to get this working? Is there another component or something else that I need to configure to get it all working?
I look forward you your help
Thanks,
Trent

Hi Trent,
If both the RD session broker and the NLB are working fine in
the internal network, I suspect that there is something wrong with the external connection. I’d like to confirm the following questions to narrow down this issue:
1.
Can you PING and telnet this RDS farm name when encountering the “disconnect” issue? For example: telnet farmname
3389.
2.
Can you individually connect to the RDS server when failing to connect it via farm name?
3.
Did you configure any certificate on the RDS server or RD gateway server?
4.
Do you get any event log when this issue happens on the server and client side? If yes, please let me know it word-by-word including the event ID.
Thanks.

What is the Max Nat Session supported on ASR 1002 with ASR1002-5G/K9

Hello,
I am going for ASR 1002 With ASR1002-5G/K9 ESP, Can any 1 help me to know how many NAT translation is possible.
As I got the Datasheet for ASR1000 it say’s 1M translation is Supported by ESP10 but it’s not giving any information regarding ESP5.
Thanks in advance

Firewall or NAT: 250,000 sessions and 50,000 sessions-per-sec setup rate
This is from the datasheet. Pls check.
Table 3. Cisco ASR 1000 Series 5-Gbps ESP Module Performance and Scaling
Regards
Durga Prasad - Datasoft Comnet
Pls rate helpful posts
Sent from Cisco Technical Support Android App

ASR 1002 Monitor Session doesn't works.

Similar Messages

Maybe you are looking for