ASR 1006 Aux port

I can't use Aux port for ASR 1006, becouse i can't find it in configuration.
Version: asr1000rp2-advipservicesk9.03.07.05.S.152-4.S5.bin"
router#sho line ?
  <0-16>       First Line range
  async-queue  Show async-queue
  console      Primary terminal line
  summary      Quick line status summary
  vty          Virtual terminal
  |            Output modifiers
<cr>
router#sho line
   Tty Typ     Tx/Rx    A Modem  Roty AccO AccI   Uses   Noise  Overruns   Int
     0 CTY              -    -      -    -    -      0       0     0/0       -
*    1 VTY              -    -      -    -    1      4       0     0/0       -
*    2 VTY              -    -      -    -    1     16       0     0/0       -
*    3 VTY              -    -      -    -    1      2       0     0/0       -
     4 VTY              -    -      -    -    1      3       0     0/0       -
Can you help me whith my problem?

Hi,
I see you are using initiator unclassified ip-address. How exactly are you trying to trigger the session here? What type of traffic are you sending from your CPE? Please make sure you send a packet which 'crosses' the ISG box. A packet with destination the ISG will not trigger a session. Only a packet that needs to be forwarded by the ISG will. If you are not seeing anything with those debugs, it seems like no FSOL is seen to spawn the session.
Also, if your subscriber is connected with L2 network, why do you configure "ip subscriber routed"? This is conceptually wrong since you are telling to ISG that the subscriber is connecting via a L3 routed network which is not correct according to what you say.
Regards

Similar Messages

How to disable AUX port in ASR 9010

Hi All,
How to disable the AUX port in ASR 9010. Inside "line aux" I can't configure anything except "login authentication" (which is used for aaa authentication).
Also after IOS XR 3.2 the configuration for AUX port has been removed
Platform used: ASR 9010
Version: IOS-XR 4.1.2
Best Regards
Saikat Chakraborty

Hi Saikat,
AUX has the same authentication method as we have on the system. From this perspective, AUX is protected the same way as the Console port and only those who have an account can login via AUX (same way as via console). Any attempts to log on AUX will be logged:
Successful:
ksh[65902]: Successfully authenticated user 'XXX' for ksh access via 'aux' on '0/RSP0/CPU0'
Incorrect:
ksh[65902]: Failed authentication attempt by user 'YYY' for ksh access via 'aux' on '0/RSP0/CPU0
But if anyone has a physical access to the device, that would be even bigger threat compare to system protected AUX login.
BTW, tacacs authentication should work for AUX too. We’d need to define a template for it.
Example:
aaa authentication login tacacs_template group tacacs+ local
line template aux
login authentication tacacs_template
Regards,
/A

ASR 1006 shaping\policing on port-channel interfaces

Hello
I encountered a problem - ASR 1006 ignores shaping\policing configuration on a port-channel interfaces.
If I configure:
policy-map Shaping
class class-default
shape average 100000
interface TenGigabitEthernet0/0/0
no ip address
channel-group 1 mode active
interface Port-channel1.10
encapsulation dot1Q 10
ip address 1.0.0.1 255.255.255.0
service-policy output Shaping
With such configuration shaping doesn't work. But it works on ordinary tenGigabit interfaces...
I've tried several ios xe versions.. no changes
Are there any ristrictions with shaping on Port-channel interfaces?

Hi,
Traditional QoS will not work for etherchannels. Please read to find suitable config for your case.
http://www.cisco.com/c/en/us/td/docs/ios-xml/ios/qos_mqc/configuration/xe-3s/qos-mqc-xe-3s-book/qos-eth-int.html#GUID-6137A7B8-B2D1-4024-8AC9-E7EBEDD868C6

Cisco asr1000 aux-port

Hi. I have a Cisco ASR 1006 Router, with the the aux-port connected but i can´t configure the "line aux 0".. the line does not exist in the running config.
http://www.cisco.com/c/en/us/td/docs/routers/asr1000/install/guide/asr1routers/asr1higV8/asr1_hw2.html
In the related link Cisco says "The AUX port is a diagnostics access port".
I need to connect Cisco ASR1000 Aux-port with a Cisco CRS Console-Port as a second remote control method.
I Wish to confirm this before deploy several sites in the same way.
Thanks

Hi Saima,
With the Cisco 7942, you would leverage the setting under
the product specific porting of the config via device>phone
and set Wireless Headset Hookswitch Control to Enabled
http://headsetplus.com/PDF/Jabra-EHS-guide.pdf
Cheers!
Rob
"And if I should fall behind
Wait for me" - Springsteen

Command execution get very slow when AAA Authorization enable on ASR 1006

Without Authorization , I am able work smoothly with just click on ASR ...., But Once I enable Authorization it takes many secs to move to other command exampe ( If i hit config t or int gi1/0/1 , it take time to move to next command level) ...
These Authorization issue I am facing only on ASR and for Other Cisco Switches and Router its working fine wiith just a click.
Did any one face such issue , and how it is fix ...
See the Show version for ASR
Cisco IOS Software, IOS-XE Software (PPC_LINUX_IOSD-ADVIPSERVICESK9-M), Version 15.1(2)S, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2011 by Cisco Systems, Inc.
Compiled Thu 24-Mar-11 23:32 by mcpre
Cisco IOS-XE software, Copyright (c) 2005-2011 by cisco Systems, Inc.
All rights reserved. Certain components of Cisco IOS-XE software are
licensed under the GNU General Public License ("GPL") Version 2.0. The
software code licensed under GPL Version 2.0 is free software that comes
with ABSOLUTELY NO WARRANTY. You can redistribute and/or modify such
GPL code under the terms of GPL Version 2.0. For more details, see the
documentation or "License Notice" file accompanying the IOS-XE software,
or the applicable URL provided on the flyer accompanying the IOS-XE
software.
ROM: IOS-XE ROMMON
NOITDCRTRCORP01 uptime is 10 weeks, 6 days, 1 hour, 16 minutes
Uptime for this control processor is 10 weeks, 6 days, 1 hour, 19 minutes
System returned to ROM by reload
System restarted at 17:47:32 IST Thu Oct 4 2012
System image file is "bootflash:/asr1000rp1-advipservicesk9.03.03.00.S.151-2.S.bin"
Last reload reason: EHSA standby down
AAA Commands on ASR 1006
aaa new-model
aaa group server tacacs+ tacgroup
server 10.48.128.10
server 10.72.160.10
ip vrf forwarding Mgmt-intf
ip tacacs source-interface GigabitEthernet0
aaa authentication login default group tacgroup local
aaa authentication enable default group tacgroup enable
aaa accounting exec default start-stop group tacgroup
aaa accounting commands 1 default start-stop group tacgroup
aaa accounting commands 15 default start-stop group tacgroup
aaa accounting connection default start-stop group tacgroup
aaa accounting system default start-stop group tacgroup
aaa authorization commands 0 default group tacgroup none
aaa authorization commands 1 default group tacgroup none
aaa authorization commands 15 default group tacgroup none
aaa session-id common
tacacs-server host 10.48.128.10 key 7 13351601181B0B382F04796166
tacacs-server key 7 053B071C325B411B1D25464058

I think your issue maybe related to your tacacs server. If you re-order the two servers (typically a 5 second timer before failover occurs) and see if that improves your performance:
You can try to debug the issue by referring to the command reference guide....i.e. debug tacacs...you can also try to telnet to both ip address to port 49 to see if the connection opens, in order to rule out issues where a firewall or routing to one of the tacacs servers is failing. I also noticed you have the shared secret and tacacs server defined for one of the servers, is the sam present for the other server that is in the server group?
server 10.48.128.10
server 10.72.160.10
to
server 10.72.160.10
server 10.48.128.10
Thanks,
Tarik Admani
*Please rate helpful posts*

Maximum cos1 (voice traffic) supported by Cisco ASR 1006 router

Dear Team,
Please confirm the maximum cos 1 traffic supported by cisco ASR 1006 router.

Yes, it would. If you are planning on terminating a single site on this router I would spread over multiple routers for redundancy.
Table 6 explains number of ports and channels providing you have the DSPs:
http://www.cisco.com/c/dam/en/us/products/collateral/routers/2800-series-integrated-services-routers-isr/product_data_sheet0900aecd8057f2e0.pdf

Cisco ASR 1006 and WAAS

Hi,
Is there any built-in WAAS and NME features or services in Cisco ASR 1006? Or is there any WAAS or NME module that can be installed in Cisco ASR 1006? I found that for Cisco ISR 1900, 2900, and 3900, WAAS and NME services can be enabled by installing SRE and NME module. But can't find any information for Cisco ASR 1006.
Really appreciate your help.
Thanks

Hi Marvin
There is no option for this.
on the 4510 the only options under the interface are
speed nonegotiate or no speed nonegotiate (for auto)
Similarly on the ASR no negotiation auto or negotiation auto. setting each device to auto/manual or manual/auto has no effect on the ASR port - its still down
Cheers

Telnet to router through AUX port

i have configured my router to telnet through modem dialin but when i dials from my pc to router it give me garbage charcter in my hyperterminal. can any one help me that is this is problem with my router configuration or the cable connection with the router.
router AUX port --> ciscoconsole cable --> cisco 29-4043-01-->modem

Even though the AUX port is supposed to "auto-baud" (usually you need to hit the "Enter" key a couple times), some/many/most/all current modems will set the DTE speed (the console cable) to the DCE speed (the modem-to-modem link) ... and "auto-baud" doesn't always work.
Since the modems will (by default) connect at 56K (or the top speed), chances are that it will try to talk to your Cisco device at some baud above 9.6K, which it is probably expecting.
You can do one of a couple things:
Hard set the modems to a 9.6k DTE speed (and/or DCE speed, since you won't go faster then the slowest baud)
OR
Experiment on the router to hard set the DTE speed to the baud set on the modem's serial port (frequently 115 kilobaud).
Check it out and get back to us.
Good Luck
Scott

Connection a RS232 device to the Aux port.

Dear,
I have a home lab wthe a 2600 access server (16 port octal).
From this 2600 router I want to connect to a Raritan 8 ports RPC.
This RPC (Remote power control) has a rs232 serial port (RJ45)
I tried a lot and still I do not get connected to the RPC, has anyone ever done this before.
When I use a rs232 serial cable from the RPC to my serial pc port, I get into the rpc directly when putty is opened.
pinout RPC
Pinout Aux (cisco)
Pinout rs-232 (db9)
1 DTR
1 RTS
1 DCD
2 GND
2 DTR
2 RX
3 RTS
3 TX
3 TX
4 TX
4 GND
4 DTR
5 RX
5 GND
5 GND
6 -
6 RX
6 DSR
7 GND
7 DSR
7 RTS
8 DCD
8 CTS
8 CTS
9 RI (ring indicator)
I created several cables without succes.
I connected RTS to CTS and DTR to DSR.
On aux port I used the following.
speed 9600 8n1
transport all
modem inout
(also tried with modem printer)
I'm missing something to get is working.
Any help?
Kind regards,
Remko

If you attach this USB drive to your Mac can it be accessed now?

Air tunes wont play on home stereo using mini to RCA cord to Aux port

iTunes see's the base station and connects to it in itunes on Windows laptop and ipod touch but when the mini stereo jack to RCA 2 end cord is plugged from my home stereo to the Airport express but when I choose to play my iTunes through the base station no sound comes out through the stereo
Isn't this exactly what it is designed to do???
yes I have "home sharing on as well"
I can play my ipod touch hooked up to the stereo using the same mini jack to RCA cable whjile on the Aux port of the stereo why not the base station??
any ideas how I can get this to actually work???

Could be a firewall issue. Try disabling the firewall, reboot, and then see if it works. If so I have found that I need to uninstall iTunes, enable firewall, reboot, reinstall iTunes
CB

Aux port configuration

Hi,
I have a following configuration:
Router AUX port -> FW Console
If there is something problem in the FW I can log the FW from cisco aux but the problem is now that the aux port is sending character's to FW's console port and now if the FW is rebooting it will go bootloop because when the FW boot's there is situation where is something "press any key" and now cisco router sends characters and the FW boots again.
Router AUX port config is following:
line aux 0
no exec
transport input all
stopbits 1
Which aux-port config the Cisco won't send any character to FW's console.
br
J

Hi Jody,
Thanks for your reply.
Actually I have no logging console configured at router but I will configure this also to the FW..I forgot to configure this at FW :)

Is it possible to use Cisco 1721 AUX port to dial into MS-RAS?

Is it possible to use Cisco 1721 AUX port with external modem to dial into Microsoft W2k-RAS server?

Hello Thanks for the link. The place where I'm stuck is when the async is going through the LCP negotiation. the LCP Confreg sends but I dont' get back anything. Cisco documentation states "make sure autoselect PPP or Async mode dedicated are set but I'm actually dialing into a Microsoft RAS server. Do you know where these settings are?
*Mar 1 05:38:04.782: As65 PPP: Phase is ESTABLISHING, Active Open
*Mar 1 05:38:04.782: As65 PPP: No remote authentication for call-out
*Mar 1 05:38:04.782: As65 LCP: O CONFREQ [Closed] id 43 len 20
*Mar 1 05:38:04.782: As65 LCP: ACCM 0x000A0000 (0x0206000A0000)
*Mar 1 05:38:04.782: As65 LCP: MagicNumber 0x314EFEBB (0x0506314EFEBB)
*Mar 1 05:38:04.786: As65 LCP: PFC (0x0702)
*Mar 1 05:38:04.786: As65 LCP: ACFC (0x0802)
*Mar 1 05:38:06.782: As65 LCP: TIMEout: State REQsent
*Mar 1 05:38:06.782: As65 LCP: O CONFREQ [REQsent] id 44 len 20
*Mar 1 05:38:06.782: As65 LCP: ACCM 0x000A0000 (0x0206000A0000)
*Mar 1 05:38:06.782: As65 LCP: MagicNumber 0x314EFEBB (0x0506314EFEBB)
*Mar 1 05:38:06.782: As65 LCP: PFC (0x0702)
*Mar 1 05:38:06.782: As65 LCP: ACFC (0x0802)
*Mar 1 05:38:08.782: As65 LCP: TIMEout: State REQsent
*Mar 1 05:38:08.782: As65 LCP: O CONFREQ [REQsent] id 45 len 20
*Mar 1 05:38:08.782: As65 LCP: ACCM 0x000A0000 (0x0206000A0000)
*Mar 1 05:38:08.782: As65 LCP: MagicNumber 0x314EFEBB (0x0506314EFEBB)
*Mar 1 05:38:08.782: As65 LCP: PFC (0x0702)
*Mar 1 05:38:08.782: As65 LCP: ACFC (0x0802)

How to fix aux port on cdx-gt250mp car stereo.

everything else works, but aux port quit working. after clicking select button until AUX appears on screen, it then immediately says "FRONT IN" and then goes blank

Hello serenajohnson
Welcome to Sony Community.
Ensure that a straight type plug has been used.
After "FRONT IN" appears, start playing back the portable audio device.
Try connecting a different device to the AUX IN jack of the Car Stereo.
If the same issue persists with a different portable audio device, then the Car Stereo will require service.
Refer to the below link to locate the nearest authorized service centers.
https://eservice.sony.com
Regards,
Colby

ASR 1001 OTV Port-Channel

I saw in the release notes that 3.10 for the ASR 1001 supports port-channel for the internal otv interface. I upgraded to that release and it lets me use a port-channel interface, but it won't let me use the serivce instance command on the L2 interface. I can add the channel-group command but not any otv commands. Has anyone seen this yet?
Thanks,
Tom

Hi tom,
Not sure if you have resolved this issue, but, I hope you are configuring the port-channel with all the service-instance configurations. If yes, and you are getting into issues, please do post the output of the issue, we can have a look at the same.

Why is my Iphone not working through my vehicle's Aux. port ?????????

Perhaps someone can respond to my issue with not being able to get my iphone to work through my vehicle's Auxilary Jack.
I bought a Monster Cable kit for Ipods. It is used to plug into your ipod then into your vehicle's Aux. port. Well it works perfect on my regular Ipod.
However it does nothing when I try it with my Iphone.
Any suggestions?
Thank you,
Robbie
[email protected]

I bought a Belkin cable
http://store.apple.com/1-800-MY-APPLE/WebObjects/AppleStore.woa/wa/RSLID?nnmm=br owse&mco=EEBCC376&node=home/iphoneaccessories/cablesdocks
and have no problems. Maybe Monster doesn't work with the iPhone.

ASR 1006 Aux port

Similar Messages

Maybe you are looking for