ASR 9001 BNG IPoE problems
Hi,
I have read and try these guides
https://supportforums.cisco.com/docs/DOC-23170
https://supportforums.cisco.com/docs/DOC-19702
https://supportforums.cisco.com/docs/DOC-19726
But have some problems , here is my config ( almost same like the guides )
radius-server host xxx.xxx.xxx.46 auth-port 1812 acct-port 1813!aaa server radius dynamic-author port 3799 client yyy.yyy.yyy.102 vrf default ! client xxx.xxx.xxx.46 vrf default !aaa attribute format MY_AUTH mac-address! aaa attribute format NAS_PORT_FORMAT circuit-id plus remote-id separator .!!aaa radius attribute nas-port format e SSAAPPPPQQQQQQQQQQVVVVVVVVVVUUUU type 32aaa radius attribute nas-port format e SSAAPPPPQQQQQQQQQQVVVVVVVVVVUUUUaaa radius attribute nas-port-id format NAS_PORT_FORMATaaa group server radius RADIUS_GR server xxx.xxx.xxx.46 auth-port 1812 acct-port 1813 source-interface Loopback0!aaa authorization network default group RADIUS_GRaaa accounting subscriber default group RADIUS_GRaaa authorization subscriber AUTH_GR group RADIUS_GRaaa authorization subscriber default group RADIUS_GRaaa authorization subscriber RADIUS_GR group RADIUS_GRaaa authentication subscriber default group RADIUS_GRaaa accounting update periodic 10dhcp ipv4 profile IP_DEFAULT proxy class IP_DEFAULT helper-address vrf default yyy.yyy.yyy.102 giaddr zzz.zzz.zzz.1 ! helper-address vrf default yyy.yyy.yyy.102 giaddr zzz.zzz.zzz.1 relay information option relay information policy keep relay information option allow-untrusted ! interface Bundle-Ether100.361 proxy profile IP_DEFAULT!ipv4 access-list PERM_ALL 10 permit ipv4 any any 20 permit icmp any any 30 permit ipv4 any any!interface Bundle-Ether100 bundle load-balancing hash dst-ip!!interface Bundle-Ether100.361 ipv4 point-to-point ipv4 unnumbered Loopback100 service-policy type control subscriber IP_PM encapsulation dot1q 361 ipsubscriber ipv4 l2-connected initiator dhcp !!interface Loopback0 ipv4 address ccc.ccc.ccc.174 255.255.255.255!interface Loopback100 description 4dhcp ipv4 address zzz.zzz.zzz.1 255.255.255.0!interface TenGigE0/0/2/0 bundle id 100 mode on!interface TenGigE0/0/2/1!dynamic-template type ipsubscriber IPSUB_TPL ipv4 unnumbered Loopback100 ipv4 access-group PERM_ALL ingress ipv4 access-group PERM_ALL egress !class-map type control subscriber match-any DHCP match protocol dhcpv4 end-class-map!policy-map type control subscriber IP_PM event session-start match-first class type control subscriber DHCP do-until-failure 5 activate dynamic-template IPSUB_TPL 10 authorize aaa list AUTH_GR format MY_AUTH password cisco ! ! end-policy-map!
Without service-policy type control subscriber IP_PM on the interface , CPE gets ip address and all works.
The radius server is configured always to autothenticate with access-accept but there are errors
Total Deadtime: 0s Last Deadtime: 0s
Timeout: 5 sec, Retransmit limit: 3
Quarantined: No
Authentication:
468 requests, 1 pending, 154 retransmits
0 accepts, 0 rejects, 0 challenges
204 timeouts, 417 bad responses, 417 bad authenticators
0 unknown types, 417 dropped, 0 ms latest rtt
Throttled: 0 transactions, 0 timeout, 0 failures
Estimated Throttled Access Transactions: 0
Maximum Throttled Access Transactions: 0
The most strange issue is this
000c.42a8.71e2 0.0.0.0 INIT 57 BE100.361 default 0x0
and
RP/0/RSP0/CPU0:Sep 23 17:08:03.507 : dhcpd[1077]: DHCPD ERROR: TP2468: rib route delete failed, null ifhandle or IPv4 address
Here is the subscriber session info
RP/0/RSP0/CPU0:ASR9001#show subscriber session all
Mon Sep 23 17:08:46.995 EET
Codes: IN - Initialize, CN - Connecting, CD - Connected, AC - Activated,
ID - Idle, DN - Disconnecting, ED - End
Type Interface State Subscriber IP Addr / Prefix
LNS Address (Vrf)
IP:DHCP No CN -
RP/0/RSP0/CPU0:ASR9001#show subscriber session all detail
Mon Sep 23 17:08:48.394 EET
Interface: None
Circuit ID: 000401690107
Remote ID: 0006001ebd7b2f00
Type: IP: DHCP-trigger
IPv4 State: Up Pending, Mon Sep 23 17:08:32 2013
Mac Address: 000c.42a8.71e2
Account-Session Id: 000001e0
Nas-Port: 67114640
User name: unknown
Outer VLAN ID: 361
Subscriber Label: 0x0000005f
Created: Mon Sep 23 17:08:32 2013
State: Connecting
Authentication: unauthenticated
Access-interface: Bundle-Ether100.361
Policy Executed:
policy-map type control subscriber IP_PM
event Session-Start match-first [at Mon Sep 23 17:08:32 2013]
class type control subscriber DHCP do-until-failure [Succeeded]
5 activate dynamic-template IPSUB_TPL [Succeeded]
Session Accounting: disabled
Last COA request received: unavailable
Pending Callbacks:
Waiting for Authorization to complete
Waiting for Authentication response from AAA
Hi Alex, i have downgrade my router to 4.3.4, in this version there are no DHCPv4 Server option. how do i get the dhcp server in my router ?
I have try to connect my demo client, the result is my router doesn't recieved Accept-Access from my Radius and also the routing system still send radius packet from interface physical instead loopback0.
Access-Request from Router to Radius # 7 09:45:02.753 : radiusd[315]: RADIUS: Send Access-Request to 202.xxx.xxx.60:1645 id 24, len 254 7 09:45:02.754 : radiusd[315]: RADIUS: authenticator FC 30 00 B2 EB 76 ED 27 - 82 51 DF 8C F2 45 AA 6F 7 09:45:02.754 : radiusd[315]: RADIUS: Vendor,Cisco [26] 41 7 09:45:02.754 : radiusd[315]: RADIUS: Cisco AVpair [1] 35 client-mac-address=000f.b0d1.a219 7 09:45:02.754 : radiusd[315]: RADIUS: Vendor,Cisco [26] 34 7 09:45:02.754 : radiusd[315]: RADIUS: Cisco AVpair [1] 28 dhcp-vendor-class=MSFT 5.0 7 09:45:02.754 : radiusd[315]: RADIUS: Acct-Session-Id [44] 10 0400000a 7 09:45:02.754 : radiusd[315]: RADIUS: NAS-Port-Id [87] 13 130/8/0/905 7 09:45:02.754 : radiusd[315]: RADIUS: Vendor,Cisco [26] 19 7 09:45:02.754 : radiusd[315]: RADIUS: cisco-nas-port [2] 13 130/8/0/905 7 09:45:02.754 : radiusd[315]: RADIUS: User-Name [1] 16 000f.b0d1.a219 7 09:45:02.754 : radiusd[315]: RADIUS: Service-Type [6] 6 Outbound[5] 7 09:45:02.754 : radiusd[315]: RADIUS: User-Password [2] 18 * 7 09:45:02.754 : radiusd[315]: RADIUS: Vendor,Cisco [26] 33 7 09:45:02.754 : radiusd[315]: RADIUS: Cisco AVpair [1] 27 parent-if-handle=67111360 7 09:45:02.754 : radiusd[315]: RADIUS: NAS-Port-Type [61] 6 IPOEOVLAN[40] 7 09:45:02.754 : radiusd[315]: RADIUS: Event-Timestamp [55] 6 1389062702 7 09:45:02.754 : radiusd[315]: RADIUS: Nas-Identifier [32] 26 HOSTNAME-BNG 7 09:45:02.754 : radiusd[315]: RADIUS: NAS-IP-Address [4] 6 210.xxx.yyy.2Access-Request from Radius which got from Router #*** Received from 210.xxx.yyy.2 port 51185 ....Code: Access-RequestIdentifier: 31Authentic: *<134><174><25><251>a<140><17><170><255>S<191><205>;T<153>Attributes: cisco-avpair = "client-mac-address=000f.b0d1.a219" cisco-avpair = "dhcp-vendor-class=MSFT 5.0" Acct-Session-Id = "0400000b" NAS-Port-Id = "130/8/0/905" Cisco-NAS-Port = "130/8/0/905" User-Name = "000f.b0d1.a219" Service-Type = 5 User-Password = <251><10>h<203><11><203><151><132>i<29><222>@<251>t7<166> cisco-avpair = "parent-if-handle=67111360" NAS-Port-Type = 40 Event-Timestamp = 1389062760 NAS-Identifier = "HOSTNAME-BNG" NAS-IP-Address = 210.xxx.yyy.2##Accept-Access from Radius to Router ##Tue Jan 7 09:42:53 2014: DEBUG: Handling with Radius::AuthFILE: Tue Jan 7 09:42:53 2014: DEBUG: Radius::AuthFILE looks for match with 000f.b0d1.a219 [000f.b0d1.a219]Tue Jan 7 09:42:53 2014: DEBUG: Radius::AuthFILE ACCEPT: : 000f.b0d1.a219 [000f.b0d1.a219]Tue Jan 7 09:42:53 2014: DEBUG: AuthBy FILE result: ACCEPT, Tue Jan 7 09:42:53 2014: DEBUG: Access accepted for 000f.b0d1.a219Tue Jan 7 09:42:53 2014: DEBUG: Packet dump:*** Sending to 210.xxx.yyy.2 port 51185 ....Code: Access-AcceptIdentifier: 31Authentic: $U<226><252>4<219><171><228><226>q^<28><135>?<143><175>Attributes:## BUT The Router never recieved Access-Accept Packet from the Radius ##== Current Configuration After Downgrade to 4.3.4 ==radius source-interface Loopback0 vrf defaultradius-server host 202.158.58.60 auth-port 1645 acct-port 1646 key 7 radius-server timeout 10aaa attribute format NAS_PORT_FORMAT circuit-id plus remote-id separator #!aaa attribute format USERNAME_FORMAT mac-addressaaa group server radius radiator server 202.xx.xx.60 auth-port 1645 acct-port 1646 source-interface Loopback0!aaa accounting subscriber default group radiatoraaa authorization subscriber default group radiatoraaa authorization subscriber author_grp group radiatoraaa authentication subscriber default group radiatoraaa accounting update periodic 5dhcp ipv4 profile DHCPv4 proxy helper-address vrf default 202.xxx.1.34 giaddr 101.aaa.bbb.1 relay information option relay information policy keep relay information option allow-untrusted interface GigabitEthernet0/0/0/0.905 proxy profile DHCPv4interface Loopback0 ipv4 address 202.ccc.ddd.233 255.255.255.255interface Loopback2000 ipv4 address 101.aaa.bbb.1 255.255.255.0interface GigabitEthernet0/0/0/0.905 ipv4 point-to-point ipv4 unnumbered Loopback2000 service-policy type control subscriber IP_PM encapsulation dot1q 905 ipsubscriber ipv4 l2-connected initiator dhcp initiator unclassified-source dynamic-template type ipsubscriber IPSUB_TPL ipv4 unnumbered Loopback2000 !!class-map type control subscriber match-any IP_SUB match protocol dhcpv4 dhcpv6 end-class-map!policy-map type control subscriber IP_PM event session-start match-first class type control subscriber IP_SUB do-all 10 activate dynamic-template IPSUB_TPL 20 authorize aaa list author_grp format USERNAME_FORMAT password iosxr ! ! event account-logon match-first class type control subscriber IP_SUB do-all 10 authenticate aaa list default ! ! end-policy-map#Radius Status#show radius Tue Jan 7 09:56:52.137 GMTGlobal dead time: 0 minute(s)Number of Servers:1Server: 202.xx.xx.60/1645/1646 is UP Total Deadtime: 0s Last Deadtime: 0s Timeout: 10 sec, Retransmit limit: 3 Quarantined: No Authentication: 11 requests, 1 pending, 31 retransmits 0 accepts, 0 rejects, 0 challenges 41 timeouts, 0 bad responses, 0 bad authenticators 0 unknown types, 0 dropped, 0 ms latest rtt Throttled: 0 transactions, 0 timeout, 0 failures Estimated Throttled Access Transactions: 0 Maximum Throttled Access Transactions: 0 Automated TEST Stats: 0 requests, 0 timeouts, 0 response, 0 pending Accounting: 0 requests, 0 pending, 0 retransmits 0 responses, 0 timeouts, 0 bad responses 0 bad authenticators, 0 unknown types, 0 dropped 0 ms latest rtt Throttled: 0 transactions, 0 timeout, 0 failures Estimated Throttled Accounting Transactions: 0 Maximum Throttled Accounting Transactions: 0 Automated TEST Stats: 0 requests, 0 timeouts, 0 response, 0 pending
Similar Messages
-
I have Prime Network 4.0 and ASR 9001 with A9K-MPA-20x1GE and IOS XR 5.1.0. Prime connects to ASR9k with Telnet, SNMP and XML, status says reachable, operational. Updated prime to latest PrimeNetwork-4.0-DP1308.
Still, Prime can not see any physical interfaces except MgmtEth (no on-board 4x10G, no 20x1G). Basically, nothing in Slot0.
Can not see any VRFs and BNG functionality configured in VRF.
Only single static route in routing table (does not show connected routes in global routing table)
What can it be?
Is it me not configuring something, or Prime Network should not be seeing this things?
GeorgeI assume you are asking about Cisco Prime LAN Management System (LMS) vs. Cisco Prime Infrastructure (PI).
LMS is currently the leading Cisco offering for wired infrastructure management. It is the evolution of the earlier CiscoWorks LMS, CiscoWorks RWAN CiscoWorks 2000, CWSI, VLAN Director, original CiscoWorks classic etc. products going back almost 20 years.
PI is the equivalent Cisco offering for wireless LANs and is the successor to NCS and WCS products.
The overlap and confusion comes from the fact the Cisco is positioning PI as the overall wireless and wired management platform and gradually introducing wired network management features to make it equal (and eventually exceed) LMS's capabilities.
There is a comparison table here that shows the current differences. A major new release of PI (2.0) is due out shortly which will close many (but not all) of the gaps on that table. -
Hi All:
I would appreciate if someone can share their lifetime experience and suggest me to finalize the right product between ASR 1006 or ASR 9001.
Requirements:
- We need full internet feed with IPv4 and IPv6.
-10 G & STM-16 interfaces for connectivity.
- 10 Gbps traffic need to be handled by the box.
- MPLS L3/L2 VPN's
I personally after going through IOS-XR feature, prefer this.
Need some expert thoughts in the light of real world experience.
Regards,Hi Sayed,
ASR 9001 does not support STM-16 interfaces. It is purely 1 GE/10 GE platform.
If you are looking for an XR platform that supports STM-16 interfaces, you need to go with the 9006 (or 9904) , RSP-440, SIP-700 and POS SPA (for STM) and Typhoon 10GE linecard. (with Trident you might face an issue for the number of learned prefixes depending on the scale profile you choose: http://www.cisco.com/c/en/us/support/docs/routers/asr-9000-series-aggregation-services-routers/116999-problem-line-card-00.html)
If you decide to go with the ASR 1006, make sure you choose dual RP2 ( with 16GB mem), ESP-100 (or ESP-200) and SIP40. This should eliminate the TCAM exhaustion issue, if you decide to do NAT and ACL.; and guarantee and route-scale that might occur. (for the ASR 1000, I would recommend upgrading all of the memories)
HTH,
Michel. -
ASR 9001 NP1 FAILED_TX_PATH,
Dear All,
I have problem with below log and suddenly the NP stop forwarding packet please advise the solution and how to reset the NP or do i need to reload the entire box ?
LC/0/0/CPU0:Nov 12 11:29:05.192 : pfm_node_lc[285]: %PLATFORM-DIAGS-0-LC_NP_LOOPBACK_FAILED_TX_PATH : Set|online_diag_lc[139346]|Line card NPU loopback Test(0x2000006)|link failure mask is 0x2.
Please help.
Regards, Pok.Dear Akiritch,
Thank you. How do we reload the LC example we used ASR 9001 port 0/0/2/0-1 belong to NP0 and port 0/0/2/2-3 belong to NP1.
RP/0/RSP0/CPU0:XR#show controller np ports all
Thu Nov 13 08:06:32.854 KHMER
Node: 0/0/CPU0:
NP Bridge Fia Ports
0 0 0 GigabitEthernet0/0/0/0 - GigabitEthernet0/0/0/19
0 0 0 TenGigE0/0/2/0, TenGigE0/0/2/1
1 1 1
1 1 1 TenGigE0/0/2/2, TenGigE0/0/2/3 ==> This NP1 problem how can we reload it ?
Regards, Pok. -
ASR-9001 - XR_434 - HSRP
How many HSRP / Subinterfaces will be recomend to be the max in a Teng. port for an ASR-9001.
If i have over 500, what will be the configuration best practice?
I have seen Multiple Group Optimization (MGO) for HSRP as an option, but i dont have a clear example of how to configure it on XR.In spanish ¡¡ APLAUSOS !!
Also i take a look on Struc 33 of the NP, and the max entries change from 1024 to 8192
router hsrp
interface TenGigE0/0/0/3
address-family ipv4
hsrp 4094
name PRINCIPAL
priority 110
track object PRUEBA_1 40
interface TenGigE0/0/0/3.2
address-family ipv4
hsrp 2 slave
follow PRINCIPAL
address 198.18.0.1
interface TenGigE0/0/0/3.3
address-family ipv4
hsrp 3 slave
follow PRINCIPAL
address 198.18.0.9
RP/0/RSP0/CPU0:ASR-9001_1#sh hsrp br
Wed Mar 25 02:13:58.791 MEX
IPv4 Groups:
P indicates configured to preempt.
|
Interface Grp Pri P State Active addr Standby addr Group addr
Te0/0/0/3 4094 70 Init unknown unknown unknown
Te0/0/0/3.2 2 sla Init unknown unknown 198.18.0.1
Te0/0/0/3.3 3 sla Init unknown unknown 198.18.0.9
RP/0/RSP0/CPU0:ASR-9001_1#show controllers np struct 33 np0 location 0/0/CPU0
Wed Mar 25 02:14:30.375 MEX
Node: 0/0/CPU0:
NP: 0 Struct 33: VRRP_MAC
Struct is a PHYSICAL entity
Reserved Entries: 0, Used Entries: 6, Max Entries: 8192
Tks!!!! -
ASR-9001 - XR_434 - A9K-MPA-4x10GE - not fowarding packets
In ASR-9001 with XR Version 434
Connection between 2 devices, same platform, same XR Version (434) packets are not been foward.
Change XR Version to 5.1.3 and the fowarding was sucesfull.
Does anyone have the BUGs related to this and the SMUs that i can install to keep working with 434?
RegardsNoup, the ingress / egress counters keep in 0, some times ARP complete sometimes it dont.
The router crash traing to do an OIR.
RP/0/RSP0/CPU0:ASR-9001#admin show inst act summ
Default Profile:
SDRs:
Owner
Active Packages:
disk0:asr9k-mini-px-4.3.4
disk0:asr9k-k9sec-px-4.3.4
disk0:asr9k-mcast-px-4.3.4
disk0:asr9k-optic-px-4.3.4
disk0:asr9k-fpd-px-4.3.4
disk0:asr9k-doc-px-4.3.4
disk0:asr9k-mpls-px-4.3.4
disk0:asr9k-px-4.3.4.CSCul58246-1.0.0
disk0:asr9k-px-4.3.4.CSCui94441-1.0.0
disk0:asr9k-px-4.3.4.CSCug75299-1.0.0
disk0:asr9k-px-4.3.4.CSCuj01579-1.0.0
disk0:asr9k-px-4.3.4.CSCum51429-1.0.0 -
Asr-9001-s upgrade license - SFP+2 and SFP+3 ?
I cannot seem to find a part number for a license upgrade to enable the addtional 2 10Gig sfp's on an asr-9001-s.
Does anyone have that information with the cost associated with it?
Thanks
TomHello,
If you upload the new IOS XE image change the boot statement in the config to the new image, then reboot, this should not have any change to how the ASR was operating before. (do read the release notes though in case)
If you already have the Advanced IP services license installed, you will not need another one. This stays with the ASR even when you change the IOS XE image on your ASR. I think actually the show ver will show the license information too.
show license all - this command will show you detailed information about license on your ASR
conf t
license boot level advipservices - this will ensure your next boot uses this feature set.
hth
Bilal -
Hi,
I want to use the nV feature to cluster 2 ASR 9001.
For that I will need to add the A9K-NV-CLUSTR-LIC license.
What would the A9K-NVSAT5-LIC do for me? (nV Host License for up to 5 nV clients) I would need it to cluster my 2 ASR 9001?
I would also like to know if I would require the L-A9K-9001OPT-LIC= (ASR 9001 Advanced Optical License) in order to use 10Gbps fiber connections. What does this license provide to my ASR 9001?
Thanks a lot for the help.
Regards,
JHi.
Let me answer your questions. I wrote an article about licensing on ASR 9000 - http://blog.netfi.co/cisco-asr-9000-licensing/
1. nV Licensing
A9K-NV-CLUSTR-LIC is for nV Edge
A9K-NVSAT5-LIC allows you to connect 5 satellites (9000v, 901 or 903).
Additionaly you need appropriate license on ASR 901 or ASR 903. ASR 9000v doesn't require any additional license. More about it in my article.
2. L-A9K-9001OPT-LIC=
You don't need this license to use 10G links. It allows you to configure G.709/ONT on 10G interfaces. -
Hello,
We try to use ipsec with our ASR 9001 but even if we do crypto isakmp:
how crypto isakmp peers
Tue Apr 14 20:47:17.751 UTC
% IKE not active
How can we active IKE ?
Thks.Hi Jordi,
We are getting ipsec support with the "help"of the VSM (virtual services module).
this module carries as bunch of cpu's on top of which applications can be loaded. eg CGN, coming soon IPSEC and DPI also.
This module requires a slot. The asr9001 doesnt have slots so it can't carry the VSM, for which you need a 9904/9006/9010/9922.
There was talks about a crypto MPA too, I need to check in on that and will report back if there are plans for it.
regards
xander -
Hi,
I am planning to buy new ASR 9001-S with A9K-MPA-20xGE card.
Any help regarding following questions are very appreciated:
- Does IOS XR operating system some by default with the router or I have to order that separately?
- According to the documentation, the RSP processor inside ASR 9001-S should include 8 GB RAM. Should be that ordered separately or it is included by default?
- Do I need any additional license for routing/switching functionality, BGP full table, HSRP/VRRP, netflow..?
- Does ASR 9001-S support TCP MSS feature?
Thank you very much in advance for the help!
Kind regards
SaljaThat doesn't sound right to me Salja to be honest, but then I never really order the stuff, I just build it :) The way our sales force generally goes about it is one of the line items is the ios-xr software, effectively the right to use license and then you can pick the release you want.
431 is very old already hence I am questioning the validity of that answer. If XR 43 was selected you would get 434 minimally.
Anyways, regardless as to what rls it comes with, you can always download and upgrade your device with the release of choice from CCO.
cheers!
xander -
ASR 9001 temperature threshold
Hi, we have a couple of ASR 9001.
The threshold value on our managment sytem for the temperature is 45 C.This value seems to be too low to me
Does anyone know the temperature threshold of the ASR 9001 Router?
I found nothing in the documents.
br, PeterHi Sam,
you misunderstand me.
What I am looking for is the threshhold for alarms.
like this example from a N5k
show environment temperature
Temperature
Module Sensor MajorThresh MinorThres CurTemp Status
(Celsius) (Celsius) (Celsius)
1 Outlet 67 58 47 ok
At which temperatur logs/sends the router the MinorThres alarm, and of course the MajorThresh alarm?
br, Peter -
Hello,
We install a news asr 9001 but each time we reload it, it ask us to enter a new root-system password.
an idea why ?So, neither the admin config nor the normal config are getting saved correctly.
I would recommend 2 steps:
1- Check the
IOX_ADMIN_CONFIG_FILE=
IOX_CONFIG_FILE=
Variables on rommon mode the "set" command gives you all the variables, verify they have a valid path/file
2- Follow the IOS-XR install guide to initialize all devices and services (you can find the install guide on Cisco documentation) -
Hi,
What is new with ASR-9001-FAN-V2 vs. ASR-9001-FAN? I cannot find any information about that on cisco.com nor googeling...
FlorianHi Sam,
"Also note that this part is not supported until 5.1.1"
What does this mean exactly? For eg. I can't see the power supplies in "show inventory" on a router with version 4.3.4. Are there any other drawbacks or must the router be upgraded to >= 5.1.1?
I also see this:
Fan Information
Fan speed (rpm) and run time (in hours) :
FAN0 FAN1 FAN2 FAN3 FAN4 FAN5 FAN6 FAN7 FAN8 FAN9 FAN10 FAN11 FAN12 FAN13
0/FT0/* (Speed)
10800 10830 10860 10920 10860 10920 11010 10950 10950 10830 10950 10920
Notice that FAN12 and FAN 13 have no output.
Does this mean that v2 fan has less fans than v1 or all of them are not functioning because of an unsupported version?
Thanks, Karlo. -
Does the asr 9001 ship with a console cable ? The normal console cable does not seems to work ( used 115200 8N1 and No Flow).
Did any one have difficulties connecting the asr 9001 for the first time ?I used an ordinary, blue DB9-to-RJ45, Cisco console cable (I believe it's called rollover cable) that I use for all Cisco devices that I need console access to (and not only those - same cables work for Sun servers as well).
I can't remember if the ASR was packed with its own console cable, but even if it was, I didn't use it. -
Hello,
As I understood, ASR 9001 has integrated 4 onboard 10 GB interfaces and two Line Card slots. It has MOD 80 architecture.
Onboard 10 Gb interfaces has same QoS capabilities as MOD TR modular line cards. ( 8 queues per port and etc)
What about the two Line Card Slots? If I use A9K-MPA-20x1GE, A9K-MPA-2x10GE or A9K-MPA-4x10GE line card , which QoS specifications I will have? Like MOD SE or MOD TR? As I know, these line cards has SE functions on the ASR 9001/9001S. Does it mean more than 8 queues per port? Can I terminate Pseudowire Headend on these interfaces and use QoS on them?
Regards,
GunerNoup, the ingress / egress counters keep in 0, some times ARP complete sometimes it dont.
The router crash traing to do an OIR.
RP/0/RSP0/CPU0:ASR-9001#admin show inst act summ
Default Profile:
SDRs:
Owner
Active Packages:
disk0:asr9k-mini-px-4.3.4
disk0:asr9k-k9sec-px-4.3.4
disk0:asr9k-mcast-px-4.3.4
disk0:asr9k-optic-px-4.3.4
disk0:asr9k-fpd-px-4.3.4
disk0:asr9k-doc-px-4.3.4
disk0:asr9k-mpls-px-4.3.4
disk0:asr9k-px-4.3.4.CSCul58246-1.0.0
disk0:asr9k-px-4.3.4.CSCui94441-1.0.0
disk0:asr9k-px-4.3.4.CSCug75299-1.0.0
disk0:asr9k-px-4.3.4.CSCuj01579-1.0.0
disk0:asr9k-px-4.3.4.CSCum51429-1.0.0
Maybe you are looking for
-
How to open a DWG file with AutoCAD options (AppleScript)?
Hi, I'm looking for help specifying the AutoCAD options when opening DWG files. I have DWG files of floor plans that I always want to open at the same scale. I can successfully open a DWG file with the default options using: open POSIX file "/Users
-
Hello, problem with a movie that I bought
a few minutes ago, I've just bought The Hobbit in normal definition it cost 14 $.The point is that the HD version worths the same price than the normal , and i wanna know how can i get the HD for free, or how to switch? T
-
Why is Firefox 29 is laggy for me?
Hi, since I updated to FF 29, my browser has gotten unbearably laggy/choppy. If I type, letters appear slower than I hit the keys, and if I move my mouse over a link it takes a second or two before the link overlay effect (underline, highlight etc) a
-
Smallest file size for talking head, MPEG1?
Hey friends, back again, still using PRE8. I have to encode a talking head into a watchable quality for a podcast. Prefer between 320x240 and 640x480, prefer the later. I inadvertently tried some combination of VCD 352x240 and got an amazingly small
-
My E71 didn't startup after the last update!
I updated my E71 today. This isn't my first time. What happened today as usual after completing the update. It says startup your phone. I tried several times but it didn't startup the only thing is gives is the keypad light, it turn on like twice the