ASR 9001 temperature threshold

Hi, we have a couple of ASR 9001.
The threshold value on our managment sytem for the temperature is 45 C.This value seems to be too low to me
Does anyone know the temperature threshold of the ASR 9001 Router?
I found nothing in the documents.
br, Peter

Hi Sam,
you misunderstand me.
What I am looking for is the threshhold for alarms.
like this example from a N5k
show environment temperature
Temperature
Module   Sensor     MajorThresh   MinorThres           CurTemp     Status
                              (Celsius)           (Celsius)              (Celsius)
1        Outlet             67                      58                     47                    ok
At which temperatur logs/sends the router the MinorThres alarm, and of course the MajorThresh alarm?
br, Peter

Similar Messages

ASR-9001 - XR_434 - HSRP

How many HSRP / Subinterfaces will be recomend to be the max in a Teng. port for an ASR-9001.
If i have over 500, what will be the configuration best practice?
I have seen Multiple Group Optimization (MGO) for HSRP as an option, but i dont have a clear example of how to configure it on XR.

In spanish ¡¡ APLAUSOS !!
Also i take a look on Struc 33 of the NP, and the max entries change from 1024 to 8192
router hsrp
interface TenGigE0/0/0/3
address-family ipv4
   hsrp 4094
    name PRINCIPAL
    priority 110
    track object PRUEBA_1 40
interface TenGigE0/0/0/3.2
address-family ipv4
   hsrp 2 slave
    follow PRINCIPAL
    address 198.18.0.1
interface TenGigE0/0/0/3.3
address-family ipv4
   hsrp 3 slave
    follow PRINCIPAL
    address 198.18.0.9
RP/0/RSP0/CPU0:ASR-9001_1#sh hsrp br
Wed Mar 25 02:13:58.791 MEX
IPv4 Groups:
                        P indicates configured to preempt.
                        |
Interface      Grp Pri P State   Active addr     Standby addr   Group addr
Te0/0/0/3      4094 70   Init    unknown         unknown        unknown
Te0/0/0/3.2       2 sla   Init    unknown         unknown        198.18.0.1
Te0/0/0/3.3       3 sla   Init    unknown         unknown        198.18.0.9
RP/0/RSP0/CPU0:ASR-9001_1#show controllers np struct 33 np0 location 0/0/CPU0
Wed Mar 25 02:14:30.375 MEX
                Node: 0/0/CPU0:
NP: 0 Struct 33: VRRP_MAC
Struct is a PHYSICAL entity
Reserved Entries: 0, Used Entries: 6, Max Entries: 8192
Tks!!!!

ASR-9001 - XR_434 - A9K-MPA-4x10GE - not fowarding packets

In ASR-9001 with XR Version 434
Connection between 2 devices, same platform, same XR Version (434) packets are not been foward.
Change XR Version to 5.1.3 and the fowarding was sucesfull.
Does anyone have the BUGs related to this and the SMUs that i can install to keep working with 434?
Regards

Noup, the ingress / egress counters keep in 0, some times ARP complete sometimes it dont.
The router crash traing to do an OIR.
RP/0/RSP0/CPU0:ASR-9001#admin show inst act summ
Default Profile:
SDRs:
    Owner
Active Packages:
    disk0:asr9k-mini-px-4.3.4
    disk0:asr9k-k9sec-px-4.3.4
    disk0:asr9k-mcast-px-4.3.4
    disk0:asr9k-optic-px-4.3.4
    disk0:asr9k-fpd-px-4.3.4
    disk0:asr9k-doc-px-4.3.4
    disk0:asr9k-mpls-px-4.3.4
    disk0:asr9k-px-4.3.4.CSCul58246-1.0.0
    disk0:asr9k-px-4.3.4.CSCui94441-1.0.0
    disk0:asr9k-px-4.3.4.CSCug75299-1.0.0
    disk0:asr9k-px-4.3.4.CSCuj01579-1.0.0
    disk0:asr9k-px-4.3.4.CSCum51429-1.0.0

MacBook Pro temperature threshold

I travel 100% for my job and I am curious as to if anyone knows what the temperature threshold is for the MacBook Pro? Right now I leave my MacBook Pro inside an InCase backpack inside my rental car in the front seat of a secured parking lot. However, outside temperatures where I am are only getting up to about 20 degrees Fahrenheit. Are there any specifications or recommendations from Apple regarding “don't have your MacBook Pro in outside temps below xx degrees, and don't have your MacBook Pro in outside temps above xx degrees?”
MacBook Pro Mac OS X (10.4.7) 1GB RAM, 100GB HD, 256MB Video RAM

I just came back from a roadtrip to Vegas and we were driving in 110 F weather, sometimes more. My MBP was in the trunk in a black case, where I thought it'd be reasonably shielded...but when I took it out the entire case was scalding. Do I have anything to worry about? It seems to be working fine...any words of reassurance would be great; I just bought this thing and it's my baby.

Asr-9001-s upgrade license - SFP+2 and SFP+3 ?

I cannot seem to find a part number for a license upgrade to enable the addtional 2 10Gig sfp's on an asr-9001-s.
Does anyone have that information with the cost associated with it?
Thanks
Tom

Hello,
If you upload the new IOS XE image change the boot statement in the config to the new image, then reboot, this should not have any change to how the ASR was operating before. (do read the release notes though in case)
If you already have the Advanced IP services license installed, you will not need another one. This stays with the ASR even when you change the IOS XE image on your ASR. I think actually the show ver will show the license information too.
show license all - this command will show you detailed information about license on your ASR
conf t
license boot level advipservices - this will ensure your next boot uses this feature set.
hth
Bilal

Change CPU temperature threshold

Is it possible to change or set the temperature threshold for the cpu clock throttle?
Feb 22 13:04:28 -toshiba kernel: CPU1: Core temperature above threshold, cpu clock throttled (total events = 1)
Feb 22 13:04:28 -toshiba kernel: CPU0: Core temperature above threshold, cpu clock throttled (total events = 1)
Feb 22 13:04:28 -toshiba kernel: CPU4: Package temperature above threshold, cpu clock throttled (total events = 1)
Feb 22 13:04:28 -toshiba kernel: CPU3: Package temperature above threshold, cpu clock throttled (total events = 1)
Feb 22 13:04:28 -toshiba kernel: CPU5: Package temperature above threshold, cpu clock throttled (total events = 1)
Feb 22 13:04:28 -toshiba kernel: CPU6: Package temperature above threshold, cpu clock throttled (total events = 1)
Feb 22 13:04:28 -toshiba kernel: CPU2: Package temperature above threshold, cpu clock throttled (total events = 1)
Feb 22 13:04:28 -toshiba kernel: CPU7: Package temperature above threshold, cpu clock throttled (total events = 1)
Feb 22 13:04:28 -toshiba kernel: CPU0: Package temperature above threshold, cpu clock throttled (total events = 1)
Feb 22 13:04:28 -toshiba kernel: CPU1: Package temperature above threshold, cpu clock throttled (total events = 1)
Feb 22 13:04:28 -toshiba kernel: CPU1: Core temperature/speed normal
Feb 22 13:04:28 -toshiba kernel: CPU7: Package temperature/speed normal
Feb 22 13:04:28 -toshiba kernel: CPU0: Core temperature/speed normal
Feb 22 13:04:28 -toshiba kernel: CPU4: Package temperature/speed normal
Feb 22 13:04:28 -toshiba kernel: CPU3: Package temperature/speed normal
Feb 22 13:04:28 -toshiba kernel: CPU5: Package temperature/speed normal
Feb 22 13:04:28 -toshiba kernel: CPU6: Package temperature/speed normal
Feb 22 13:04:28 -toshiba kernel: CPU2: Package temperature/speed normal
Feb 22 13:04:28 -toshiba kernel: CPU0: Package temperature/speed normal
Feb 22 13:04:28 -toshiba kernel: CPU1: Package temperature/speed normal

Works fine booted under Windows. The tablet is known to run "hot", but well under TJ max. RealTemp in Windows shows it hoving around 49C idle and up to 80C, with well within limits and matches all other Lenovo Helix's posting their temp results online. Hot, yes, but acceptable.
When I get time I'll go back in and view the sensors. I suspect one or two things:
* Sensors are outta wack, giving false numbers.
* The kernel driver is too conservative and it thinks an 70C temp is bad or something. <- harder to prove.
The BIOS handles everything fine. When I disable PState in Windows (force everything to 100), temps range from 62C to 81C at all times. Still within specifications. This is BIOS-controlled cooling controlling the fans.
^- this is what I want for Arch. Controlling PState is great, but if there's a problem I want it to get out of the way and just let the BIOS handle things. Don't force it.
I'm quite surprised Arch attempts to handle this on its own automagically without some special configuration or wiki page to set it up.
Last edited by eduncan911 (Today 05:56:17)

Prime Network and ASR 9001

I have Prime Network 4.0 and ASR 9001 with A9K-MPA-20x1GE and IOS XR 5.1.0. Prime connects to ASR9k with Telnet, SNMP and XML, status says reachable, operational. Updated prime to latest PrimeNetwork-4.0-DP1308.
Still, Prime can not see any physical interfaces except MgmtEth (no on-board 4x10G, no 20x1G). Basically, nothing in Slot0.
Can not see any VRFs and BNG functionality configured in VRF.
Only single static route in routing table (does not show connected routes in global routing table)
What can it be?
Is it me not configuring something, or Prime Network should not be seeing this things?
George

I assume you are asking about Cisco Prime LAN Management System (LMS) vs. Cisco Prime Infrastructure (PI).
LMS is currently the leading Cisco offering for wired infrastructure management. It is the evolution of the earlier CiscoWorks LMS, CiscoWorks RWAN CiscoWorks 2000, CWSI, VLAN Director, original CiscoWorks classic etc. products going back almost 20 years.
PI is the equivalent Cisco offering for wireless LANs and is the successor to NCS and WCS products.
The overlap and confusion comes from the fact the Cisco is positioning PI as the overall wireless and wired management platform and gradually introducing wired network management features to make it equal (and eventually exceed) LMS's capabilities.
There is a comparison table here that shows the current differences. A major new release of PI (2.0) is due out shortly which will close many (but not all) of the gaps on that table.

ASR 1006 vs ASR 9001

Hi All:
I would appreciate if someone can share their lifetime experience and suggest me to finalize the right product between ASR 1006 or ASR 9001.
Requirements:
- We need full internet feed with IPv4 and IPv6.
-10 G & STM-16 interfaces for connectivity.
- 10 Gbps traffic need to be handled by the box.
- MPLS L3/L2 VPN's
I personally after going through IOS-XR feature, prefer this.
Need some expert thoughts in the light of real world experience.
Regards,

Hi Sayed,
ASR 9001 does not support STM-16 interfaces. It is purely 1 GE/10 GE platform.
If you are looking for an XR platform that supports STM-16 interfaces, you need to go with the 9006 (or 9904) , RSP-440, SIP-700 and POS SPA (for STM) and Typhoon 10GE linecard. (with Trident you might face an issue for the number of learned prefixes depending on the scale profile you choose: http://www.cisco.com/c/en/us/support/docs/routers/asr-9000-series-aggregation-services-routers/116999-problem-line-card-00.html)
If you decide to go with the ASR 1006, make sure you choose dual RP2 ( with 16GB mem), ESP-100 (or ESP-200) and SIP40. This should eliminate the TCAM exhaustion issue, if you decide to do NAT and ACL.; and guarantee and route-scale that might occur. (for the ASR 1000, I would recommend upgrading all of the memories)
HTH,
Michel.

ASR 9001 NP1 FAILED_TX_PATH,

Dear All,
I have problem with below log and suddenly the NP stop forwarding packet please advise the solution and how to reset the NP or do i need to reload the entire box ?
LC/0/0/CPU0:Nov 12 11:29:05.192 : pfm_node_lc[285]: %PLATFORM-DIAGS-0-LC_NP_LOOPBACK_FAILED_TX_PATH : Set|online_diag_lc[139346]|Line card NPU loopback Test(0x2000006)|link failure mask is 0x2.
Please help.
Regards, Pok.

Dear Akiritch,
Thank you. How do we reload the LC example we used ASR 9001 port 0/0/2/0-1 belong to NP0 and port 0/0/2/2-3 belong to NP1.
RP/0/RSP0/CPU0:XR#show controller np ports all
Thu Nov 13 08:06:32.854 KHMER
Node: 0/0/CPU0:
NP Bridge Fia Ports
0 0 0 GigabitEthernet0/0/0/0 - GigabitEthernet0/0/0/19
0 0 0 TenGigE0/0/2/0, TenGigE0/0/2/1
1 1 1
1 1 1 TenGigE0/0/2/2, TenGigE0/0/2/3 ==> This NP1 problem how can we reload it ?
Regards, Pok.

ASR 9001 Licensing

Hi,
I want to use the nV feature to cluster 2 ASR 9001.
For that I will need to add the A9K-NV-CLUSTR-LIC license.
What would the A9K-NVSAT5-LIC do for me? (nV Host License for up to 5 nV clients) I would need it to cluster my 2 ASR 9001?
I would also like to know if I would require the L-A9K-9001OPT-LIC= (ASR 9001 Advanced Optical License) in order to use 10Gbps fiber connections. What does this license provide to my ASR 9001?
Thanks a lot for the help.
Regards,
J

Hi.
Let me answer your questions. I wrote an article about licensing on ASR 9000 - http://blog.netfi.co/cisco-asr-9000-licensing/
1. nV Licensing
A9K-NV-CLUSTR-LIC is for nV Edge
A9K-NVSAT5-LIC allows you to connect 5 satellites (9000v, 901 or 903).
Additionaly you need appropriate license on ASR 901 or ASR 903. ASR 9000v doesn't require any additional license. More about it in my article.
2. L-A9K-9001OPT-LIC=
You don't need this license to use 10G links. It allows you to configure G.709/ONT on 10G interfaces.

ASR 9001 + IPSEC

Hello,
We try to use ipsec with our ASR 9001 but even if we do crypto isakmp:
how crypto isakmp peers
Tue Apr 14 20:47:17.751 UTC
% IKE not active
How can we active IKE ?
Thks.

Hi Jordi,
We are getting ipsec support with the "help"of the VSM (virtual services module).
this module carries as bunch of cpu's on top of which applications can be loaded. eg CGN, coming soon IPSEC and DPI also.
This module requires a slot. The asr9001 doesnt have slots so it can't carry the VSM, for which you need a 9904/9006/9010/9922.
There was talks about a crypto MPA too, I need to check in on that and will report back if there are plans for it.
regards
xander

ASR 9001-S

Hi,
I am planning to buy new ASR 9001-S with A9K-MPA-20xGE card.
Any help regarding following questions are very appreciated:
- Does IOS XR operating system some by default with the router or I have to order that separately?
- According to the documentation, the RSP processor inside ASR 9001-S should include 8 GB RAM. Should be that ordered separately or it is included by default?
- Do I need any additional license for routing/switching functionality, BGP full table, HSRP/VRRP, netflow..?
- Does ASR 9001-S support TCP MSS feature?
Thank you very much in advance for the help!
Kind regards
Salja

That doesn't sound right to me Salja to be honest, but then I never really order the stuff, I just build it :) The way our sales force generally goes about it is one of the line items is the ios-xr software, effectively the right to use license and then you can pick the release you want.
431 is very old already hence I am questioning the validity of that answer. If XR 43 was selected you would get 434 minimally.
Anyways, regardless as to what rls it comes with, you can always download and upgrade your device with the release of choice from CCO.
cheers!
xander

ASR 9001 - root password

Hello,
We install a news asr 9001 but each time we reload it, it ask us to enter a new root-system password.
an idea why ?

So, neither the admin config nor the normal config are getting saved correctly.
I would recommend 2 steps:
1- Check the
IOX_ADMIN_CONFIG_FILE=
IOX_CONFIG_FILE=
Variables on rommon mode the "set" command gives you all the variables, verify they have a valid path/file
2- Follow the IOS-XR install guide to initialize all devices and services (you can find the install guide on Cisco documentation)

ASR-9001-FAN-V2

Hi,
What is new with ASR-9001-FAN-V2 vs. ASR-9001-FAN? I cannot find any information about that on cisco.com nor googeling...
Florian

Hi Sam,
"Also note that this part is not supported until 5.1.1"
What does this mean exactly? For eg. I can't see the power supplies in "show inventory" on a router with version 4.3.4. Are there any other drawbacks or must the router be upgraded to >= 5.1.1?
I also see this:
Fan Information
Fan speed (rpm) and run time (in hours) :
FAN0 FAN1 FAN2 FAN3 FAN4 FAN5 FAN6 FAN7 FAN8 FAN9 FAN10 FAN11 FAN12 FAN13
0/FT0/* (Speed)
10800 10830 10860 10920 10860 10920 11010 10950 10950 10830 10950 10920
Notice that FAN12 and FAN 13 have no output.
Does this mean that v2 fan has less fans than v1 or all of them are not functioning because of an unsupported version?
Thanks, Karlo.

ASR 9001 console cable

Does the asr 9001 ship with a console cable ? The normal console cable does not seems to work ( used 115200 8N1 and No Flow).
Did any one have difficulties connecting the asr 9001 for the first time ?

I used an ordinary, blue DB9-to-RJ45, Cisco console cable (I believe it's called rollover cable) that I use for all Cisco devices that I need console access to (and not only those - same cables work for Sun servers as well).
I can't remember if the ASR was packed with its own console cable, but even if it was, I didn't use it.

ASR 9001 temperature threshold

Similar Messages

Maybe you are looking for