ASR Connected to 5508 HA pair

I have single ASR1006 and I'm attempting to add some redundancy to my WLCs that attach directly.  Right now, I have a single interface connected to a 5508.  Using subinterfaces I run the different WLANs and route them at the ASR.  I would like to have this 5508 pair up in HA, but I'm not sure how best to configure the ASR to do this.  I'm trying to avoid fronting them with a switch stack if possible.  One thought was to create a channel-group on the ASR that two ports are members of;one going to WLC 1 and the other to WLC 2.  Then I would be routing on the sub po1.xxx interfaces.  I'm not sure if the etherchannel would send the traffic correctly to the WLCs though.  I'm thinking the WLCs would still be in LAG mode for this.  Any thoughts?

Its really best practice to have a switch interface with the WLC's.  One of the important things also if your use LAG is the etherchannel should be set on the switch side as src-ip-dst.  Especially when you are doing HA, you might even run into more issues due to the design you are trying to use. 
Thanks,
Scott
Help out other by using the rating system and marking answered questions as "Answered"

Similar Messages

  • I've found two bugs in iOS 7. 1) declined calls does not appear as missed calls on the lock screen/notification centre. 2) when bluetooth is enabled from control center, it does not connect to an already paired bluetooth device

    I've found two bugs in iOS 7:
    1) declined calls does not appear as missed calls on the lock screen/notification centre - iOS 7.0.2.
    2) when bluetooth is enabled from control center, it does not connect to an already paired bluetooth device automatically - iOS 7.0.

    We are all users here, just like you, but you can tell Apple about it by using this link:
    Apple - iPhone - Feedback

  • Its a 5S,I couldnt automatically connect to an already paired bluetooth device the next time.Have to forget that device then re establish each time.Am i missing any setting that does it ?Also

    Its a 5S,I couldnt automatically connect to an already paired bluetooth device the next time.Have to forget that device then re establish each time.Am i missing any setting that does it ?Also if i turn on the bluetooth via settings and turn off it via control center,the settings page still reflects its on ,is that a bug in IOS ?

    What kind of Bluetooth device?
    When you turn it off in Control Center, are you looking at the Settings page? If so, you need to close control center for it to reflect the change. When you turn Bluetooth off in Control Center and look on the Status Bar, what do you see? Do you see the gray Bluetooth icon? If you have Settings closed and turn Bluetooth off on the Control Center and then open the Settings app, do you still see Bluetooth enabled?

  • TS4456 New Mac mini and older wireless keyboard connect, but don't pair

    In setting up my brand new Mac mini, the wireless mouse paired with no problem, but I'm having trouble with the keyboard. I am using an older mouse and keyboard from my previous mini, which is completely shut down. The keyboard shows as being connected to the computer, but when I enter the code and press Return, the code disappears and nothing else happens. After a while the code reappears and I repeat the process with the same results. After several attempts, nothing else happens. I've tried rebooting twice, checked the keyboard batteries, made sure the keyboard light is blinking to show it's discoverable, but I can't move past this screen. I don't know what else to try. Please help!

    Hi, it isn't paired to another device is it?
    Might see this...
    http://www.christopher-parsons.com/blog/technology/solved-bluetooth-devices-not- connecting-to-osx/

  • ITunes cannot connect to iPhone because pairing record missing

    I was able to connect my iPhone to iTunes once and was able to sync. Now i recieve a message saying: iTunes cannot connect to my iPhone because the pairing record is missing. What do I do?

    BPH108,
    I had the same exact issue. What solved this for me was to unplug my phone, shut down ITunes, shutdown my phone (Not just shut down but hold the home and lock button until it shuts off), start my phone back up and start ITunes back up. Then when I plugged my phone back in it worked like a charm!
    Hope this helps!

  • 3602E won't connect to 5508 WLAN

    Hi all,
    This is a lab system that I'm just building out- I try to see the obvious but it does bite me occasionally.  I have a 5508 WLC running release 7.4.1.  My AP's are all Cisco 3602E's with the AC modules.  My problem is that the Access points can't seem to join the WLAN- I can see them talking, debug output below. They are pingable from the WLC CLI, verified that options 43 and 60 are ok, Here's my debug:
    Under SECURITY > AAA > AP Policies the only thing checked is:
    Accept Manufactured Installed Certificate (MIC)
    *spamApTask4: Aug 12 17:35:35.724: ec:e1:a9:da:65:b0 CAPWAP Control Msg Received from 192.168.1.79:34805
    *spamApTask4: Aug 12 17:35:35.724: ec:e1:a9:da:65:b0 packet received of length 1400 from 192.168.1.79:34805
    *spamApTask4: Aug 12 17:35:35.724: ec:e1:a9:da:65:b0 Msg Type = 3 Capwap state = 0
    *spamApTask4: Aug 12 17:35:35.725: ec:e1:a9:da:65:b0 Total msgEleLen = 1348
    *spamApTask4: Aug 12 17:35:35.725: ec:e1:a9:da:65:b0 Total msgEleLen = 1279
    *spamApTask4: Aug 12 17:35:35.725: ec:e1:a9:da:65:b0 Total msgEleLen = 1235
    *spamApTask4: Aug 12 17:35:35.725: ec:e1:a9:da:65:b0 Total msgEleLen = 1215
    *spamApTask4: Aug 12 17:35:35.725: ec:e1:a9:da:65:b0 Total msgEleLen = 1207
    *spamApTask4: Aug 12 17:35:35.725: ec:e1:a9:da:65:b0 Total msgEleLen = 1202
    *spamApTask4: Aug 12 17:35:35.725: ec:e1:a9:da:65:b0 Total msgEleLen = 1197
    *spamApTask4: Aug 12 17:35:35.726: ec:e1:a9:da:65:b0 Total msgEleLen = 1189
    *spamApTask4: Aug 12 17:35:35.726: ec:e1:a9:da:65:b0 Total msgEleLen = 1183
    *spamApTask4: Aug 12 17:35:35.726: ec:e1:a9:da:65:b0 Vendor specific payload from AP  EC:E1:A9:DA:65:B0 validated
    *spamApTask4: Aug 12 17:35:35.726: ec:e1:a9:da:65:b0 Total msgEleLen = 1166
    *spamApTask4: Aug 12 17:35:35.726: ec:e1:a9:da:65:b0 Vendor specific payload from AP  EC:E1:A9:DA:65:B0 validated
    *spamApTask4: Aug 12 17:35:35.726: ec:e1:a9:da:65:b0 Created AP ec:e1:a9:da:65:b0
    *spamApTask4: Aug 12 17:35:35.727: ec:e1:a9:da:65:b0 Join Request: Total msgEleLen = 1348
    *spamApTask4: Aug 12 17:35:35.727: ec:e1:a9:da:65:b0 Join Request: Total msgEleLen = 1279
    *spamApTask4: Aug 12 17:35:35.727: ec:e1:a9:da:65:b0 Join Request: Total msgEleLen = 1235
    *spamApTask4: Aug 12 17:35:35.727: ec:e1:a9:da:65:b0 Join Request: Total msgEleLen = 1215
    *spamApTask4: Aug 12 17:35:35.727: ec:e1:a9:da:65:b0 Join Request: Total msgEleLen = 1207
    *spamApTask4: Aug 12 17:35:35.727: ec:e1:a9:da:65:b0 Join Request: Total msgEleLen = 1202
    *spamApTask4: Aug 12 17:35:35.727: ec:e1:a9:da:65:b0 Join Request: Total msgEleLen = 1197
    *spamApTask4: Aug 12 17:35:35.727: ec:e1:a9:da:65:b0 Join Request: Total msgEleLen = 1189
    *spamApTask4: Aug 12 17:35:35.727: ec:e1:a9:da:65:b0 Join Request: Total msgEleLen = 1183
    *spamApTask4: Aug 12 17:35:35.727: ec:e1:a9:da:65:b0 Vendor specific payload from AP  EC:E1:A9:DA:65:B0 validated
    *spamApTask4: Aug 12 17:35:35.727: ec:e1:a9:da:65:b0 Join request: Vendor payload type = 2, length = 13
    *spamApTask4: Aug 12 17:35:35.727: ec:e1:a9:da:65:b0 Join Request: Total msgEleLen = 1166
    *spamApTask4: Aug 12 17:35:35.727: ec:e1:a9:da:65:b0 Vendor specific payload from AP  EC:E1:A9:DA:65:B0 validated
    *spamApTask4: Aug 12 17:35:35.727: ec:e1:a9:da:65:b0 Join request: Vendor payload type = 207, length = 10
    *spamApTask4: Aug 12 17:35:35.727: ec:e1:a9:da:65:b0 Join Request: Total msgEleLen = 1152
    *spamApTask4: Aug 12 17:35:35.727: ec:e1:a9:da:65:b0 Vendor specific payload from AP  EC:E1:A9:DA:65:B0 validated
    *spamApTask4: Aug 12 17:35:35.727: ec:e1:a9:da:65:b0 Join request: Vendor payload type = 123, length = 19
    *spamApTask4: Aug 12 17:35:35.727: ec:e1:a9:da:65:b0 Join Request: Total msgEleLen = 1129
    *spamApTask4: Aug 12 17:35:35.727: ec:e1:a9:da:65:b0 Join Request: Total msgEleLen = 1120
    *spamApTask4: Aug 12 17:35:35.727: ec:e1:a9:da:65:b0 Join Request: Total msgEleLen = 1111
    *spamApTask4: Aug 12 17:35:35.727: ec:e1:a9:da:65:b0 Vendor specific payload from AP  EC:E1:A9:DA:65:B0 validated
    *spamApTask4: Aug 12 17:35:35.727: ec:e1:a9:da:65:b0 Join request: Vendor payload type = 104, length = 1107
    *spamApTask4: Aug 12 17:35:35.727: ec:e1:a9:da:65:b0 Sending encrypted packet to AP 192.168.1.79(34805)
    *spamApTask4: Aug 12 17:35:35.727: ec:e1:a9:da:65:b0 Join Request: Total msgEleLen = 0
    *spamApTask0: Aug 12 17:35:35.728:  Received SPAM_GOT_AAA_RESPONSE
    *spamApTask0: Aug 12 17:35:35.728: ec:e1:a9:da:65:b0 DTLS connection 0x1769a5b0 closed by controller
    *spamApTask0: Aug 12 17:35:35.728: DTL Deleting AP 36 - 0.0.0.0
    *spamApTask4: Aug 12 17:35:35.729: CAPWAP DTLS connection closed msg
    My console messages from the AP are:
    *Aug 12 21:54:09.135: %MESH-6-LINK_UPDOWN: Mesh station f872.eae8.7f40 link Down
    *Aug 12 21:54:11.135: %LINK-6-UPDOWN: Interface BVI1, changed state to down
    *Aug 12 21:54:16.079: %CAPWAP-3-ERRORLOG: Go join a capwap controller
    *Aug 12 21:54:16.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_ip: 192.168.1.21 peer_port: 5246
    *Aug 12 21:54:19.555: %LINEPROTO-5-UPDOWN: Line protocol on Interface BVI1, changed state to down
    *Aug 12 21:54:19.555: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to reset
    *Aug 12 21:54:20.031: %LINK-6-UPDOWN: Interface Dot11Radio0, changed state to up
    *Aug 12 21:54:25.187: %LINK-6-UPDOWN: Interface Dot11Radio1, changed state to down
    *Aug 12 21:54:25.195: %LINK-5-CHANGED: Interface Dot11Radio1, changed state to reset
    *Aug 12 21:54:26.187: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio1, changed state to down
    *Aug 12 21:54:26.215: %LINK-6-UPDOWN: Interface Dot11Radio1, changed state to up
    *Aug 12 21:54:27.215: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio1, changed state to up
    *Aug 12 21:54:49.531: %LINK-6-UPDOWN: Interface Dot11Radio1, changed state to down
    *Aug 12 21:54:49.539: %LINK-5-CHANGED: Interface Dot11Radio1, changed state to reset
    *Aug 12 21:54:49.999: DTLS_CLIENT_ERROR: ../capwap/base_capwap/dtls/base_capwap_dtls_connection_db.c:2051 Max retransmission count reached!
    *Aug 12 21:54:50.531: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio1, changed state to down
    *Aug 12 21:54:50.559: %LINK-6-UPDOWN: Interface Dot11Radio1, changed state to up
    *Aug 12 21:54:51.559: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio1, changed state to up
    *Aug 12 21:54:59.671: %DTLS-5-SEND_ALERT: Send FATAL : Close notify Alert to 192.168.1.21:5246
    *Aug 12 21:54:59.671: %MESH-6-CAPWAP_RESTART: Mesh Capwap re-started
    *Aug 12 21:54:59.671: %CAPWAP-3-ERRORLOG: Go join a capwap controller
    *Aug 12 21:54:16.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_ip: 192.168.1.21 peer_port: 5246
    *Aug 12 21:54:16.003: %LINK-6-UPDOWN: Interface Dot11Radio0, changed state to down
    *Aug 12 21:54:16.011: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to reset
    *Aug 12 21:54:17.003: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to down
    *Aug 12 21:54:17.031: %LINK-6-UPDOWN: Interface Dot11Radio0, changed state to up
    *Aug 12 21:54:17.999: %LINK-6-UPDOWN: Interface BVI1, changed state to up
    *Aug 12 21:54:18.031: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to up
    *Aug 12 21:54:18.999: %LINEPROTO-5-UPDOWN: Line protocol on Interface BVI1, changed state to up
    *Aug 12 21:54:21.159: %DTLS-5-SEND_ALERT: Send FATAL : Close notify Alert to 192.168.1.21:5246
    *Aug 12 21:54:21.199: %DHCP-6-ADDRESS_ASSIGN: Interface BVI1 assigned DHCP address 192.168.1.80, mask 255.255.255.0, hostname APf872.eae8.7f40
    Odd thing is that I am seeing this under recent traps, although I am not using any AAA sergver or RADIUS server- none are configured at all.
    Thanks!
    Jerry

    I would upgrade your wireless LAN controller to 7.5 version because the 802.11ac technology is supported on that version only so the access point might be waiting for that version to join. I say might because I don't have access points with ac modules yet but I am completelly sure and possitive that 802.11ac is supported from the 7.5 version so, if you have the modules and want to use the ac technology you will need to upgrade your WLC anyways.
    Best regards,
    Marco Gonzalez

  • Itunes could not connect to iphone because pairing record is missing???

    I have just upgraded to iphone 4s from iphone 4 and when i connect it to my itunes i get the message "itunes could not connect to iphone 'iphone' because pairing record is missing. Any clues what i've missed???
    Also my when i try to backup my iphone 4 to icloud it keeps stopping saying 'incomplete'???

    Try disconnecting your phone from your computer, quit iTunes, connect you phone to your computer again, the re-launch iTunes.

  • Bluetooth connects but will not pair to device

    Iphone 5 running on 7.1.2. bluetooth connects to CAR KIT but will not pair (does not ask for code after connecting). audio only plays from phone and not through the speakers connected by bluetooth. I have done the apple trouble solution steps and the problem still persists. any help would be appreciated. the device is compatible with iPhone.

    Hey there jrf07d,
    It sounds like your phone is not pairing to your vehicles bluetooth connection. I would recommend these steps to get it paired, from the following article:
    iOS: Troubleshooting Bluetooth connections
    http://support.apple.com/kb/TS4562
    On your iOS device, tap Settings > Bluetooth and find your device in the list. If your device says Not Connected, tap the name of your accessory to attempt to connect it.
    Tap Settings > Bluetooth and turn Bluetooth off and then on again.
    Restart your iOS device.
    Tap Settings > Bluetooth and locate the Bluetooth accessory you are currently connected to or attempting to connect to. Then tap and "Forget this Device". Try to pair your Bluetooth accessory again.
    You may need to your Bluetooth accessory PIN again if your accessory requires one. Some common PINs are 0000, 1111, and 1234.
    Restart your Bluetooth accessory by turning it off and then on again1.
    Update your device to the latest version of software. See how to update your iPhone, iPad, or iPod touch.
    If your Bluetooth accessory has upgradable firmware, check to see that you have the latest version1, 2.
    Can't pair to a Bluetooth accessory
    If you see the word "Connected" next to a Bluetooth accessory in Settings > Bluetooth, your iOS device is already paired to a Bluetooth accessory. Remember, you can only connect to one Bluetooth accessory at a time.
    If your Bluetooth accessory requires a PIN for pairing, be sure that you are entering the correct PIN1.
    Reset network settings by tapping Settings > General > Reset > Reset Network Settings.
    This will reset all network settings including: previously connected Wi-Fi networks and passwords, recently used Bluetooth accessories, VPN and APN settings.
    Thank you for using Apple Support Communities.
    All the best,
    Sterling

  • Connecting LAP1231 using stacked pair of 3750's switch

    I am trying to connect my LAP1231 to switch port on stack pair of 3750s that is connected to 6509 switch. When I look at the mac address table of the 6509 switch I don't see the mac address of my LAP. I have the switch port configured on the 3750 to right VLAN and set switchport host as well as switchport mode access. I have 27 other LAP access points connection and this is the only one I am having troubles with. Does anyone know of some issue with stacked 3750-24 switches running 12.2(25r)
    Thanks,
    Gary

    After I sent sumitted the posting I found my problem. I had added a VLAN list to the interface and forgotten I had done this. Once I added the VLAN to the list everything worked as advertised. Thanks for the response.
    Gary

  • Connection between 5508 WLC and 3750-24PS switch

    I have to realize a connection between  an 5508 WLC and 3750 switch using one SFP cable. I found on Cisco documentation some reference about two different SFP cables.
    The first one is CAB-SFP-50CM, but this is used to interconnect two 3560 switches.
    The second is SFP-H10GB-CU1M. This one has SFP+ transceivers on both ends which I don’t know if are compatible with the standard SFP ports that can be found both on WLC and switch.
    My question is if I can use one of these cables in order to connect my devices, or if you know other one piece SFP cables.
    Many thanks

    I know that you can use those SFP transceivers, but I want to know if someone tried to use the SFP-H10GB cables for this kind of connection. Because I saw on another vendor website that the SFP+ cables are compatible with standard SFP ports, and I wanted to see if it is the same for Cisco cables too.
    Regards

  • How can I connect one 5508 and a 4402?

    Hello all, I´m new to this forum. I want to consult you because of a situation that I have.
    I need to install one 5508 and a 4402 together to bring redundancy to a wireless environment.
    Can I do this?. What are the neccesary steps to perform this?, the idea behind this is to bring redundancy is the primary WLC falls for any reason.
    Thanks so much in advance.
    Regards!

    The link will explain a lot, but one thing to make sure also is that your configuration between the two WLC's are similar except for host name and up address. You will also configure the ap with the primary wlc and secondary wlc info. This way the ap knows which wlc it belongs to and which wlc it needs to go to if the primary is unavailable.
    Sent from Cisco Technical Support iPhone App

  • 5508 HA pair licenses

    I have 2 5508 that are currently running as active with 150 licenses each. I want to go to HA SSO can 100 of the licenses be relicensed to the primary since it only requires 50 licenses to convert an active license 5508 to standby HA SSO?

    So are you saying if the 5508's were purchased with 100 each and a 50 adder license was added to each the 50 could possibly get rehosted from what will be the standby to the soon to be primary?
    Thanks for your response

  • Minimum connection speeds 5508 controller and 2602E APs

                       We have an applicaiton that is sensitive to network speeds.  Is there a way to guarantee a minimum wireless network speed such as 100 MBs utilizing a 5508 controller and 2602e APs?

    We have an applicaiton that is sensitive to network speeds.  Is there a way to guarantee a minimum wireless network speed such as 100 MBs utilizing a 5508 controller and 2602e APs?
    Not easy.   Wireless is a shared medium.  This means if one client talks, everyone else has to stop and wait for their turn.
    It's like doing video.  Video is time-sensitive.  If you put a single AP in a room (granted you've got full 1Gbps ethernet access all the way), and you get 25 people continuously streaming videos, then you'll see some impact.  Bring the number down to say, 8 to 10 and you'll see improvements.
    What kind of application are we talking about here?

  • Upgrade download for iPod Touch....wiped it clean,...says Error: unable to connect...missing pairing file????? HELP!!!!!

    Luckily...I backed my iPod up first...However, now I'm apparently missing a pairing file if I ever want to be able to get it going again...Does anyone have any kind of advice?

    See this previous discussion.
    pairing record ?: Apple Support Communities

  • Can I programmtically pair a bluetooth connection LV2009

    Past post from 2007 indicate that there is no pairing function in labview, however I would like to revisit this question now with LabVIEW 2009.  I looked in the examples, and look on the bluetooth connectivity pallete, still no pairing but I"m sure there must be a way to do it programatically.
    Wii users have been finding ingenious ways to do things with their wii remotes, maybe one of the wii users would like to comment?
    Is there anyway to use labview to programatically pair bluetooth?  A dll?  .net? anything?
    -Regards
    eximo
    UofL Bioengineering M.S.
    Neuronetrix
    "I had rather be right than be president" -Henry Clay

    A clever program, but I don't see where it allows pairing with a bluetooth device?  There isn't a pop up or place to enter pairing ID
    -Regards
    eximo
    UofL Bioengineering M.S.
    Neuronetrix
    "I had rather be right than be president" -Henry Clay

Maybe you are looking for

  • Logic Express vs OSX 10.4.9

    Anybody else having problems with Logic Express since the 10.4.9 update? My M-Audio FireWire Solo interface is distorting my guitar tracks and the trouble seems to have started around the time of the update. M-Audio says there's not ETA on a 10.4.9 d

  • PDF form field alignment - Right to Left

    Actually I developed a form which pushes the entire PDF as an attachment by email when pressing on a send button created within the form. I have also added a text to appear within the email body message in Arabic language but its appearing on the lef

  • Oracle Portal for LDAP Authentication using Iplanet directory server

    I have oracle portal on solaries machine and Iplanet directory server 5.1 on windows NT, Can i user portal user authentication Iplanet LDAP. Regards srinivas

  • Assigning Form to Approval Process

    Hi, Can anyone guide how can i assign a form (process or object) to the approval process which make the user details available to tha manager while approving his/her request. Regards Alabhya Goel

  • C program not running from terminal as expected

    Hi everyone I am starting C programming as part of my university degree, I understand most of the content so far. I am compiling and running my program in Terminal and I am having a small amount of trouble with running it. Here is how I have set my p