ASR1002-x Security License just for SSH?

Hi, we are about to buy Cisco ASR 1002-X router, By default it comes with IPBASE License.
As per PCI we shouldnt be using telnet to access router, but as per research IPBASE dont support SSH.
so does that mean i will need to buy Security license just to enable SSH feature on router for remote management ? :-s
please guide, if my assumptions are wrong.

SSH support depends on the IOS you've downloaded. Make sure the IOS filename contains "k9". If the filename doesn't contain "k9" then it doesn't support SSH.

Similar Messages

Cisco security license cost

Hi, I'm a network administrator and I wanted to get the security license price for our cisco1941K9. How could I have the cost ?
Cdlt,
GKF

you would need to contact your local Cisco partner for this information or perhaps contact an Online partner. Follow the links on the following page for more information and ordering.
http://www.cisco.com/web/ordering/or13/order_customer_help_high_level_listing.html
Please remember to select a correct answer and rate

Security License for Cisco 3900 Series

Hi,
I am having Security License (SL-39-SEC-K9) for Cisco 3900 Series router, Can somebody help me to provide sample config to configure 3945 router to act as firewall. Is there any difference with the native IOS based firewall config..
Regards,
Mukesh

Here is a detailed instruction on ISR G2 licensing (including downloading, installing, rehosting license, etc.).
Usually, you just need to go to cisco.com/go/license, enter PAK and follow detailed instructions.
HTH
Alexandr

I've forgotten the answers to my security questions, and for some reasons My rescue email is not active now, I can only access to my primary email, I have just redeemed a $25 gift card this morning, I was unable to use the money now. what should I do?

I've forgotten the answers to my security questions, and for some reasons My rescue email is not active now, I can only access to my primary email, I have just redeemed a $25 gift card this morning, I was unable to use the money now. what should I do?

You need to ask Apple to reset your security questions; this can be done by clicking here and picking a method, or if your country isn't listed, filling out and submitting this form.
They wouldn't be security questions if they could be bypassed without Apple verifying your identity.
(110676)

Security License for Cisco 3925

Hi,
I have got cisco 3925 without security license. Now I have got the L-SL-39-SEC-K9 license and need to install it. What is the process of installing this license.
Thanks in advance
Regards,
Mero

Here is a detailed instruction on ISR G2 licensing (including downloading, installing, rehosting license, etc.).
Usually, you just need to go to cisco.com/go/license, enter PAK and follow detailed instructions.
HTH
Alexandr

Purchase Real and Novelty Passports,id cards,visas,drivers license ,Permits for all countries

Purchase Real and Novelty Passports,id cards,visas,drivers license ,Permits for all countries
Are you trying to change your nationality ? do you need work papers ? do you want travel ? do you need papers you cant have ?if yes , then you are in the right place at the right time
We are an independent group of specialized IT professionals and data base technicians who are specialized in the production of quality documents such as passports,drivers license,id cards,stamps,visas,diplomes of very high quality and other products
for all countries: USA, Australia,UK, Belgium, Brazil, Canada, Italian, Finland, France, Germany, Israel, Mexico, Netherlands, South Africa, Spain, Switzerland, . This list is not full.contact General support: [email protected]
To get the additional information and place the order just call or contact us via email mobile.
Contact; [email protected]
Phone: 00237-9121-1360
Phone: +237-7397-1112
Key words
Canada
Cards
United States Cards
Student Cards
International Cards
Private Cards
Adoption Certificates
Baptism Certificates
Birth Certificates
Death Certificates
Divorce Certificates
Marriage Certificates
Custom Certificates
High School Diplomas
G.E.D. Diplomas
Home School Diplomas
College Degrees
University Degrees
Trade Skill Certificates
Social Security
Validate SSN Number
Driver License Search
Spy Products
Voice Changers
Listening Devices
Invisible Ink
DMV Record Inquiry
Background Check
Investigate Anyone
Contact; [email protected]
Phone: 00237-9121-1360
Phone; +237-7397-1112

If you want to buy high quality fake faked forged fraudulent counterfeit duplicate false camouflage diplomatic passports and other identification documents of Australia, Austria, Belgium, Canada, Finland, France, Germany, Israel, Malaysia, Netherlands, New Zealand, South Africa, Switzerland, United Kingdom, United States and some other countries please visit this website:
http://www.FakePassports.EU
E-mail: [email protected]
Diplomatic passports are also available on demand.

The VTY sessions are set for SSH, is telnet still open?

I'm in the process of enabling SSH on all of my routers, switches and firewalls. After upgrading the IOS to one that supports SSH, generating the crypto key and then setting all of the VTY sessions to SSH only, my security team informs me that telnet is still vulnerable to IP spoofing. They can demonstrate that when they launch a telnet session to one of my routers, the telnet session will pause for maybe 2 seconds before receivign the message that the session was terminated by the router. They claim this indicates that the router is responding to the telnet session and before the actual disconnect is forced they could IP spoof the box and cause a DOS.
I say boulderdash but without any proof I am forced to create a bunch of ACL's to specifically deny telnet. Here is an example of my VTY's:
line vty 0 4
access-class 23 in
exec-timeout 30 0
password 7 xxxxxxxxxxxxx
logging synchronous
transport preferred ssh
transport input ssh
transport output ssh
*The access list here is limiting access from a certain internal set of IP's.
Any thoughts?

Marcos,
Thank you for your time on this. I believe I have found and corrected my issue. In my first post I showed what the vty 0 4 sessions were set as. What I failed to show was that the "vty 5 15" sessions were only set to "no exec". So what was happening is that when I would telnet to the router, the session attempt would either walk down the list of VTY sessions looking for an open port or the router just bypassed the ones that were set for SSH and tried the first VTY port that was set for no exec. This would allow for the telnet session to attempt to open but because the router was not allowing access to the command line interpreter, the router would reject the session attempt.
To correct this I simply set up all of my VTY sessions the same way, transport SSH in & transport SSH out. The next attempt closed the telnet session immediately. I still maintain there is no need for additional access-lists as I'm trying to keep my processor's free from any additional load to allow them to process the payload traffic as efficiently as possible.
If anyone has any best practices they would care to leave here, I would be interested.
Sam

15.1 License Level for ipv6?

Specifically looking at branch routers here.
Under IOS 12.4 it was very easy to identify what features were included in a specific firmware build, you just powered up the software feature navigator entered your router and what feature you required and you would be provided with a list of firmware images to upgrade to/purchase to achieve the desired feature.
Unfortunately with 15.1 licensing this no longer works, it appears that every feature is shown as available in the "UNIVERSAL DATA" image with the unhelpful comment at the end of the list indicating that some features may require an additional license but with no pointer to discover which license level contains which feature.
To give an example, try searching for images for the CISCO887VA-M Integrated Services Router. This is available in 2 flavours ADVANCED SECURITY & ADVANCED IP SERVICES, now ADV SEC does support ipv6 but the question is how much of the ipv6 feature set does it support before an upgrade to ADV IP SERVICES is required?
Thanks for any pointers,
Iain

Roberto,
I agree that Cisco says so and also it should be so.
But it happens I know it is not true. At least for one command that many will agree is one of the most needed in the ipv6 world.
Most of us to obtain an IPv6 address from a provider use an ipv4 tunnel which requires the "tunnel mode ipv6ip"
command. This command was available in the ip plus feature set but it is not in the universal image ip base.
You need a data k9 license probably for a few commands ipv6 related. I have opened a TAC case and reported it to Cisco. No reply whatsoever.
I had to buy a 370 USD data license for my 1921 (a 1000 USD hardware) just to raise the tunnel.
this does not match with the Cisco statement:
Cisco will support packaging parity for IPv6 with IPv4, for Cisco Integrated Services Routers Generation 2, starting with Cisco IOS Software Release 15.0(1)M, as well as in future 15 M and 15 T releases. IPv6 feature support for a technology will now be packaged in the same feature set as IPv4.
In fact the ipip tunnel mode is in the base image/license.
Hope this helps
Fabio

Remote Desktop Licensing Server for multiple deployments

Hi all. I'm towards a project of implementing 4 deployments of RDS in branch offices and 1 in head office. Those tend to be VMs on Server 2012 R2.
I've began collecting info from technet and even found that great post:
http://blogs.technet.com/b/yungchou/archive/2010/01/04/remote-desktop-services-rds-architecture-explained.aspx
but I still can't figure out if I'm to use separate licensing server for all deployments or there is a possibility to use a single one for 5?

If all machines are in the same domain a single license server will be fine. you will just need to add the licence server to your individual deployments via server manager. We have a single license server for 2003TS, 2012RDS 2012citrix VDI and 2008 Citrix
XenApp

I have two AppleID's. Can I set up a new Apple ID just for document syncing in iCloud? How?

I have two AppleID's. Both use known email addresses. I need absolute security for documents. Can I set up a new Apple ID just for document syncing in iCloud? How?

Sorry, I did not mean to imply that security was non-existant or horrible, just it is online, so no absolutes.
iCloud is really not useful, IMO, for collaborating as only you or your AppleID enabled devices can access the files.
I have multiple online storage accounts with the common free services, but my most used is www.box.net. Many document apps will readily support it, and even if one does not, you can use the box.net app itself to access files, then open them in the app usually. And you can share your online folders, with reasonable controls on access to keep control of who can see (and upload or download) what.
A lot of people I know use dropbox as well, but they are usually using paid accounts (often their company sets one up for them to use to exchange files with clients) and I don't know how much better is the security on a paid dropbox account versus a free one. I suspect the free ones are on a par with box.net.
You could also use add security by using some sort of PGP or other encryption tools to encrypt files put up on the shared folder(s). You'd exchange public keys with your colleagues so they could decrypt those files once they download them. That may be overkill for many peoples needs though.
Another option, if you have an online hosting account, is to get one that offers SFTP access and use that for sharing files (the downside of that is having to distribute the password to colleagues, so you could loose control of it if one of them is careless or thoughtless with it). It seems more and more document-type apps for iOS are supporting generic FTP and SFTP as well as the popular free online storage solutions.

Port forwarding for SSH not working on WRT54G2

Hi,
I have forwarded a few ports, but can't get port 22 for SSH to work. I can SSH from within LAN, so that works. And I can access FTP from outside the LAN, when I forwarded that port. But to the same computer where I can access FTP I can't access SSH...
Would be grateful for assistance. Btw, I'm using dynamic IP (through DynDNS, but not using the DynDNS tool in the Linksys interface). I've tried with both the dynDNS domain and the IP address. And I have set a fixed IP address on the server I try to access.
Thanks,
Daniel

Make sure that if you are forwarding the port nos for SSH on WRT54G2 you need to forward it for the assinged static ip address & it should work great..just try it once.

How Do I get a License key for Trial version from the App Store?

I downloaded a Trial version of Aperture 3.1.2 a few weeks ago from the App Store. I love it. Now I want to buy it, but, can't figure out how to get a license key from the App Store. When you start up Aperture Trial version, a 'nag' box comes up asking if you want to buy the application or continue using the trial version or Authorize (I guess that is what you would pick once you have the key). If I pick "Buy", the application opens Safari and takes me to the Apple online store, NOT the App store! At the Apple Store, you can buy the key for $199 or an upgrade from a previous version for $99. Whoopie! What is Apple thinking? The App store is selling Aperture for $79.99. I guess that means you don't get the box or written manuals (which I haven't used for any software in many years).
So how do I get a license key for the App Store version? Do I just Go to the App Store, pay the money, download and install the program over again. Then transfer my trial version library somehow? Then deinstall the trial version? I'd love to buy and use Aperture for $79.99, but, I'm not willing to pay $199 for it. Apple has me confused.
Anybody have a clue?

Thanks for the 1-800 call tip Allen.
P.S. I'm quite willing to put in the time and effort necessary to learn Aperture (or any other software I decide to use, "Pro" or not). I simply don't see the value in buying the box version when I'm pretty sure I won't be using any paper manuals. I very comfortable using online help files, having done so as a professional numerical control programmer for many years in my work. For reference, I'm retired, on a limited income and will be using Aperture as a rank amateur photographer who could use a little more horsepower than iPhoto offers.
I'll call Apple tomorrow.
Kevin

Do I need a security license to setup VPN on router?

Hi All.
I'm trying to setup VPN connections on 2 different routers and I'm not sure about that Do I need a security license to setup VPN connection on router?
First one is 1941-K9 site-to-site.
Second one is 887G-K9, EasyVPN connection.
Both of them don't work properly. What do I need to check on both routers to see if they're abled for vpn connection, maybe some commands as well.
Thanks in advance.
Regards,

yes, for VPN you need a security-license.
The 1941 should show the following line:
rtr-01#sh ver | b Technology
Technology Package License Information for Module:'c1900'
Technology    Technology-package          Technology-package
              Current       Type          Next reboot
ipbase        ipbasek9      Permanent     ipbasek9
security      securityk9    Permanent     securityk9
data          None          None          None
The 887 comes by default with the "Advanced Security" feature-set. That's all you need for that device.
Don't stop after you've improved your network! Improve the world by lending money to the working poor:
http://www.kiva.org/invitedby/karsteni

Getting License Key for NSP (no E-Mail is sent)

Hello SDN Team,
as reported I have successfully installed the NW04 ABAP Sneak Preview. Now I'm trying to get a license for it at http://www.sap.com/solutions/netweaver/minisap.epx. I enter all the data, check the License Agreement, hardware key from Transaction SLICENSE, choose the System NSP and send the form. But I never got an E-Mail with the key. So I tried the System WA1 just for a test. And after just a Minute I've got the E-Mail with the key.
Regards
Gregor

lol.
@gregor,
i don't know what kind of groopie you are and why you are so opportunistic to talk for everyone.
fact is:
- some (including me) haven't even got that email.
OS: "Did you request it again - after I fixed the EmailServer?"
- others seem to have got it, but with a developer key for installation number DEMOSYSTEM whereas the installation sets the installation number to INITIAL.
the developer key for INITIAL is definitely different from the one for DEMOSYSTEM.
so to be a little constructive, at least tell people that they probably have to actualize their general license to update the installation from INITIAL to DEMOSYSTEM and afterwards use the known developer key to unlock the repository.
and don't you tell me what to post an what not to post.
anton
Message was edited by: Oliver Stiefbold

Ok i have been trying to download albums, songs, apps, etc. and my itunes keeps asking me for the security question and for the life of me i cant remember the answers. I dont know what the email is that receives the question reset.

ok i have been trying to download albums, songs, apps, etc. and my itunes keeps asking me for the security question and for the life of me i cant remember the answers. I dont know what the email is that receives the question reset. is there anything i can do to fix this or am i screwed?

If you have music that was purchased on different iTunes accounts than the one you use, then you must provide the password, otherwise the tunes are not considered yours. You can turn off iCloud and just use the usual USB sync method. But I wonder whether you'll have the same problem?

ASR1002-x Security License just for SSH?

Similar Messages

Maybe you are looking for