ASR1k: VLAN re-write and EoMPLSoGRE

Hi,
Is it possible to utilise EVC VLAN re-write together with EoMPLSoGRE on an ASR1k to extend these VLANs across a L3 boundary? Could these VLANs be extended from the same ASR1k where the VLANs' L3 sub-interfaces reside?
I am not sure that it's possible to use EVC with xconnect forwarding on an ASR1k.
Cheers,
Matt

Figure out!
the problem was on macro i have to write this:
macro auto processing type switch disabled
and then everything starts going as it should be
Regards
Pietro

Similar Messages

How to combine both DAQ AI signal, write and read file in single VI

Hi
I am the new user of LabVIEW version 7.1 for testing automation application. I have to measure 33 signals ( mostly analog like temp, pressure, etc...) from NI USB 6210 DAQ system and write in master file for future verfication.From real data or from master file back up have to write one more file if only the signal reaches steady state , which will used for analysis and same signals to be read from this file parallely & make a waveform and/or table display format.
Pl. help me to shortout this problem
note: I have plan to ugrade labVIEW version 2011 shortly, so let me know doing parrel acquistion write and read file for data analysis in same VI in version 7.1......

Parallel operations in LabVIEW are very simple. Just code it in parallel and it will work.
Try taking a look at some of the examples in the NI Example Finder (Help > Find Examples). There you will find example for writing to and reading from files, as well as data acquistion in parallel with other operations.
You might need a producer/consumer architecture is you are acquiring data very quickly.
Chris
Certified LabVIEW Architect
Certified TestStand Architect

How to set up VLAN for DATA and VOIP on SRW248G4P switch?

Hi guys,
I am totally new and was given this task to complete. I really really need help.
We are using one network 192.168.1.0
Shared with data and voip.
CISCO C870, 5 switches LINKSYS SRW248G4P .
The email wrote:-
On the Linksys switch;
- create two different VLANs one for voice and one for data.
- put a firewall between the two VLANs (between voice and data) and only enable certain ports to flow to voice network (inbound tcp 8443 and ssh )
What should i do guys? I really need a dumb guide now.
I know its simple for you guys but i am not a smart IT fella. Whats the step by step?

If the switch is new or you have support on this, then you might try calling the support center. Here is a link:
https://www.myciscocommunity.com/community/smallbizsupport
On the right hand side you can find links to the support center.
Here is a link to the guide:
http://www.cisco.com/en/US/products/ps9967/prod_maintenance_guides_list.html
@ the bottom of this link you can find your switch model, you want the larger of the two. In this guide it shows you how to create a second vlan.
Will your router be the firewall between the two?
Kindest regards,
Andrew Lissitz

Can you run two songs at once? One to write and one to record?

I have dozens of midi objects, cable routings for writing and now have added dozens of audio tracks and inputs for recording my external and internal synths. (24 tracks in realtime one pass. Not bouncing but tracking. Its so cool.)
PROBLEM: As I improve the audio workflow in a song, importing that layer into older songs creates D.I.S.CO.R.D. (Digital Input Sequencer Copy Object Reassignment Disaster!)
QUERY: Can I just use one song for writing and playing and then run another "audio input based" song in the background locked via internal time code so it can RECORD or CAPTURE what this song plays?
Or is there finally a way to import audio layers without "rebuilding the whole house"?

Maybe I'm not understanding your difficulty, but I
don't see why you have to have multiple setups, or
copy/paste/import/whatever from one song to another.
..........Been tracking and mixing in the same sequence for
years.
Why? Well......
1) there's dozens of midi modules, virtual modules and custom transformer splitter objects at the writing stage,
2) dozens of tracks, input objects and reverb busses at the "tracking stage"
3) and multiple master inserts at the mixing and output stage that output anywhere from 2 to 24 stems with their own reverbs.
When the room works it works beautifully but there are different configurations of the above for a tv series gig, movie gig, album gig etc and I'd love to be able to change config 2 or 3 without having objects jumble all over config 1.
I write and work in combinations of old and new gear from Spectrasonics and NI softsynth engines to an Oberheim Expander Roland JX10 and and Yamaha TX 816s. They all have different personalities and all work reliably and have far outlived their sys ex storage software (remember Galaxy/Sounddiver? Bye Bye since System 10)
Last year I expelled my dig gear (after too many DAE errors for all that money) and I went MOTU native and love it. But I started one interface at a time and built up my new tricks and routings gradually. As a result everytime I add another MOTU interface and change some routings around all my songs have to be retaught new routings even when its just callin up a midi writing template. Hence the need for better importing of environents or a way to reliably alter one area of the above without having to recheck all the others. And it may mean a 2 computer rig. The second computer becomes the "multitrack/master recorder", and only changes during a major upgrade while midi modules and virtual synths can come and go on computer 1.
In a few weeks my studio setup tech will come in and we'll redo all our flow charts which I'll send to you if interested. Then you'll either empathize with my problem or think I'm nuts.
Thanks for your continued interest. Its nice to lament to someone who at least knows the vocabulary.
Amin
G5 dual 2.5 Mac OS X (10.3.9) Stylus AND my original Minimoog. Lots of MOTU. No more Digi.

Closing a serial port after executing a for loop of write and reads.

Hello,
Labview is opening and then closing each write to the port. I have tried to leave the close outside of the for loop, but labview wont allow it. What do I need to change to make all the writes and reads execute on 1 open and close of the serial port.?
Thanks.
Attachments:
Controller.vi ‏27 KB

J_es--
The program that you posted looks to be ok for the most part, you might consider putting an open after your configure (but that's trivial). The other thing that is a minor issue is the loop tunnel coming out of your for loop is currently being auto-indexed. This function is used to index data for each interation of the loop. You are using a static address (not an array) and so you don't need this. If you right-click and remove the auto-index the broken wire will go away. Other than that it should be ok.
I would suggest looking at one of the shipping examples that come with LabVIEW. "Basic Serial Read and Write" is essentially the same thing that you are doing and is tested here and might save you a bit of time. Anyway, take a look if you have a second. Best of luck with your application!
John H.
Applications Engineer
National Instruments
http://www.ni.com/support

What is the significance of report writer and report painter

hi all,
can anyone throw light on report write and report painter, when and why it used with examples.
thanxs in advance
regds
hari

Dear Hari,
http://www.virtuosollc.com/PDF/Get_Reporter.pdf
http://help.sap.com/saphelp_erp2005/helpdata/en/66/bc7d2543c211d182b30000e829fbfe/frameset.htm
Report Painter allows you to create reports using data from SAP application components, which you can adapt to meet your individual requirements.
Many of your reporting requirements can already be met by using the standard reports provided by various SAP application components. If these SAP standard reports do not meet your reporting needs, Report Painter enables you to define your specific reports quickly and easily.
Report Painter fulfills a function similar to Report Writer, but is easier to use. Most of the functions found in Report Writer have been built into Report Painter; however, you do not need to be familiar with all Report Writer concepts (such as Sets) in order to use Report Painter.
When executing a Report Painter report, it is displayed by the system in Report Writer format. You thus have access to the same functions as for Report Writer reports defined in the same way, and can combine Report Painter and Report Writer reports together in a report group.
Report Painter uses a graphical report structure, which forms the basis for your report definition and displays the rows and columns as they appear in the final report output.
To facilitate report definition, you can use many of the standard reporting objects provided by SAP (such as libraries, row/column models, and standard layouts) in your own specific reports. When you define a Report Painter report you can use groups (sets). You can also enter characteristic values directly.
Advantages of Report Painter include:
Flexible and simple report definition
Report definition without using sets
Direct layout control: The rows and columns are displayed in the report definition as they appear in the final report output, making test runs unnecessary.
http://help.sap.com/saphelp_47x200/helpdata/en/56/32e339b62b3011e10000000a11402f/content.htm
http://help.sap.com/saphelp_erp2005/helpdata/en/5b/d22cee43c611d182b30000e829fbfe/frameset.htm
Regards,
Naveen.

How can i write and read the same data

hi,
         i have attached my program to this mail. i have some problems in this program.
problems:
1. I want to select the threshold for the rms,varience and s.d.
But what i used is not doing that. i want to fix the upper threshold value and lower threshold value.
when ever the input crosses upper threshold value i want the output and it will remains uptill the value above the lower threshold value.
Once it come down the lower threshold value the output should be stopped.
2. I want to write this in to a file and i want to read this file. is this possible or not.
            please try to help me i am very new with lab view6i
       REGARDS
CHAMARTHY KOMAL DILEEP.
   [email protected]
Attachments:
dileep.vi ‏93 KB

The easiest way to perform a certain action (such as file I/O) based on a certain condition (such as whether a value has passed a certain threshold) is to use a comparison VI in combination with a case structure. Then you can specify that if your rms, standard deviation and variance are above a threshold then perform a certain action.
Also consider using shift registers to keep track of data from the last loop. If I understand you correctly, you want to start logging data when an upper threshold has been passed. Then you want to continue logging data until a lower threshold is passed. I have attached a non-functional but explanatory VI that will help explain how to implement logic to that effect. It also demonstrates that you can indeed write and read from the same file in a loop. The best way to do this is to open the file before the loop, do all the necessary writing and reading in the loop, and then close the file after the loop.
Hope this helps!
Jarrod S.
National Instruments
Attachments:
dileep_example.vi ‏61 KB

Read,write and create word document with list data

Hi,
My requirement is that I have a custom list called List1 and which has a 4 (suppose XName, location, phone, email)columns and also have a Template document(.dot). If I click on save button , new document has to create from the Template document(.dot) and
should modify the content depends on list columns.
For that I need to read the document , find out the text where XName , location,,phone, email and replace with the list item data(user entered data).
Can anybody please refer links for read,write and create word document?
Thanks in advance.

Yes, you can using Office Open XML. I found it to be a lot more cumbersome and in the end not a money saving approach:
https://msdn.microsoft.com/en-us/library/office/bb448854.aspx?f=255&MSPPError=-2147217396
Kind regards,
Margriet Bruggeman
Lois & Clark IT Services
web site: http://www.loisandclark.eu
blog: http://www.sharepointdragons.com

PDF writer and distiller do not appear as available in windows 7 using Acrobat 5

Trying to install my Acrobat 5 with Windows 7. The pdf writer and distiller appear to instal after satisfying the syetm requirement for a postscript driver. The software then installs fully but the pdf writer and distiller do not show up under printers. There is a warning that a compatibility issue exists, how can this be fixed please?

Acrobat 5 is not supported on Windows 7. You need to upgrade. Sorry about that.
Ken Friedman

NI 6602 Write and Read Frequency

Hi all ,
I Have NI 6602 timing card and i'm trying to use it in order to write and read using the
DAQmxWriteCtrFreq (taskHandle1, 0, 1, 10.0, DAQmx_Val_GroupByChannel, &freq, &duty, &writtenVal, 0);
and
DAQmxReadCounterScalarF64(taskHandle2,10.0,&dataVal,0);
what i'm trying to do is to write to ctt0 and to read from ctr7 ( they are crossed in the card )
i'm having a bit problems with that can some one give me a tip on how to do it properly ?
just write freq to ctr0 and read freq from ctr7.....
Kobi Kalif
Software Engineer
Solved!
Go to Solution.

You should have the following sample installed on your PC that may help you in this task: DigPulseTrain-Cont.prj (it could be located in \program files\National Instruments\CVIx\samples\daqmx\counter\generate pulse folder)
Proud to use LW/CVI from 3.1 on.
My contributions to the Developer Zone Community
If I have helped you, why not giving me a kudos?

DAQ vi to perform digital write and read measurements using 32 bits binary data saved in a file

Hi
DAQ vi to perform digital write and read measurements using 32 bits binary data saved in a file
Two main
sections:
1)
Perform
write and read operations to and fro different spread sheet files, such that
each file have a single row of 32bits different binary data (analogous to 1D
array) where the left most bit is the MSB. I don’t want to manually enter the
32 bits binary data, I want the data written or read just by opening a file
name saves with the intended data.
      2)
And
by using test patterns implemented using the digital pattern generator or build digital data functions or otherwise, I need to
ensure that the
            binary data written to a spreadsheet file or any supported file type
then through the NI-USB 6509 is same as the data read.
I’m aware I can’t use the simulated
device to read data written to any port but if the write part of the vi works I
‘m sure the read part will work on the physical device which I’ll buy later.
My Plan
of action
I’ve
created a basic write/read file task and a write/read DAQ task for NI USB 6509
and both combine in a while loop to form a progress VI which I’m confuse of how
to proceed with the implementation.
My
greatest problem is to link both together with the correct functions or operators
such that there are no syntax/execution errors and thus achieve my intended
result.
This
project is one of my many assignments for my master thesis, so please i’ll
appreciate every help as I’m not really efficient with LabVIEW programming but
I prefer it because is fun and interesting if I get to know it.
Currently I’m
practicing with LabVIEW 8.6/NI DAQmx 8.8 Demo versions and NI USB 6509
simulated device.
Please see
the attached file for my novice progress, thanks in
advance for the support
Rgds
Paul
Attachments:
DIO_write_read DAQ from file.vi ‏17 KB

What does your file look like? The DAQmx write is expecting a single U32 value, not an array of I64.
Message Edited by vt92 on 09-16-2009 02:42 PM
"There is a God shaped vacuum in the heart of every man which cannot be filled by any created thing, but only by God, the Creator, made known through Jesus." - Blaise Pascal

Wait events 'direct path write' and 'direct path read'

Hi,
We have a query which is taking more that 2 min. It's a 9.2.0.7 database. We took the trace/tkprof of the query,and identified that there are so manay 'direct path write' and 'direct path read' wait events in the trace file.
WAIT #3: nam='direct path write' ela= 5 p1=201 p2=70710 p3=15
WAIT #3: nam='direct path read' ela= 170 p1=201 p2=71719 p3=15
In the above, "p1=201" is a file_id, but we could not find any data file, temp file, control file with that id# 201.
Can you please let us know what's "p1=201" here, how to identify the file which is causing the issue.
Thanks
Sravan

What does:
show parameter db_filesreturn? My guess, is that it returns 200.
The direct file read and direct file write events are reads and writes to TEMP tablespace. In those wait events, the file# is reported as db_files+temp file id. So, 201 means temp file #1.
Now, as to your actual performance problem.
Without seeing the SQL and the corresponding execution plan, it's impossible to be sure. However, the most common causes of temp writes are sort operations and group by operations.
If you decide to post your SQL and execution plan, please be sure to make it readable by formatting it. Information on how to do so can be found here.
Hope that helps,
-Mark
Edited by: mbobak on May 1, 2011 1:50 AM

Interruptions when I use "Write" and "Read" in the same vi.

When I use "Port Write" and "Port Read" together in the same vi and I set the output to be high level, the signal becomes oscillatory. I have read one anterior message about similar problem (using "Write to Digital Line" and "Read from Digital Line" instead of "Port Write" and "Port Read") and I proceeded as the solution suggested in the answer. However, it didn´t work.
Attached, I am sending the vi I used to test the solution.
How can I fix this problem?
Attachments:
IO.vi ‏35 KB

Hi Spencer!
The device I am using is a PCI6024-E board. I have contacted the NI Suport and now I see what I was doing wrong: in fact, I was calling a DIO Port Config.vi for each of the ports ("Port Read" and "Port "Write"), but it was done inside of a While loop (usually, most of the applications here in the lab are recursive, so it´s common for us to use big while loops for the whole program). Putting them outside (as you said, at the beginning of the program), it worked! Actually, I can´t see any reason for the program to work when the calling is outside the loop, but the important is that now it´s running properly.
Thanks a lot, Spencer!

I need to print an envelope (regualr No. 10) using Open Office Writer and HP D7160

I need to print an envelope (regualr No. 10) using Open Office Writer and HP D7160. Unbeleivably there's NO information about doing this in the hard copy user manual, nor have I been able to find anything online yet.

I need to print an envelope (regualr No. 10) using Open Office Writer and HP D7160. Unbeleivably there's NO information about doing this in the hard copy user manual, nor have I been able to find anything online yet.

Subnet vs VLAN, L2 broadcast and L3 broadcast

Hi all,
I understand what are subnets and VLANs in which subnet breakup a network into different smaller segment, whereas VLAN is the logical breaking of a physical switch into several logical ones.
By right, each subnet and VLAN belongs to its own broadcast domain.
However, there are still some grey areas which i am not able to fully grasp and hope gurus here can advice further
q1) is VLAN and subnet a 1:1 relationship ? can multiple subnets belong to a single VLAN, or multiple VLANs share a same subnet ?
The reason being I have come across a design specs which lay down "Production environment" , inside it has multiple subnets which is okay, but I am not sure are the subnets belonging to the same VLAN ? or rather can they ?
q2) if devices are from a same subnet/connected to the same switch does not need to be routable to another other subnet/network. there is no need to set a gateway ip in the devices already am i right ? But do they still need IP addresss to communicate with one another ?
q3) Technically, can a frame be send from a device to another device connected to the same switch without "IP addresses" assuming both the source and destination MACs are made known ? (meaning that the src and dest ip in the frame is empty)
q4) If multiple devices from different subnets (e.g. device a,b are from subnet ab, device c,d are from subnet cd) are connected to the same switch, are they still technically consider to be in the same broadcast domain ?
q4.1) I would assume that an arp request is a L2 broadcast am i right ? and it will affect all the devices above (a,b,c,d) despite them being in different subnet . e.g. [src mac a.b.c.d] [dst mac f.f.f.f] [src ip 192.168.1.1] [dst ip 192.68.1.10], am i right ?
q4.2) Above arp request is a L2 broadcast with specific L3 destination address but L2 broadcast address,
Is there any example on L3 broadcast (255.255.255.255) which have specific L2 destination mac address ?
q5) if mutiple devices from different subnets are connected to the same switch, is there any possibilities that frames from one subnet will inter-cross to devices on other subnet beside L2 broadcast ? Is there any other impact ?
Hope my questions make sense.
Regards,
Noob

Duplicate post, please add any answers into the other thread -
https://supportforums.cisco.com/discussion/12471861/subnet-vs-vlan-l2-broadcast-and-l3-broadcast
Jon

ASR1k: VLAN re-write and EoMPLSoGRE

Similar Messages

Maybe you are looking for