ASR9000 100G-SR with ONS-15454 100G-LC-C - problem with local SR connection

Hi
I need help with 100G IPoDWDM with ASR9000 ( DWDM bundle )
We have simple setup
ASR9000 -----100G-SR------ONS15454-------DirectFiber with attenuation ( using 1560,20 ) ------- ONS15454-----100G-SR------- ASR9000.
This is lab setup but in the future with will work as alien lambda (1560,20 ) for customer MUX/DEMUX.
But now we have just direct fiber patchcords with attenution in the LAB.
I have problem with 100G-SR optics with MPO cable - links between ASR9000s and ONS15454s never up.
Loop connection ( just for test ) with MPO cable between two asr9000 100G interface working well – link is up.(I can ping)
I can’t make link UP in any way with ONS15454 100G transponder card ( with 100G SR optics ) connected to asr9000 100G port.
DWDM side optics works well I see TX/RX power and other statistic – all are green.
I am sending and receving OTN string so this hopefuly working well.
I provisioned "Provisionable Patchcord" between both ONS15454 chassis and both 100G cards trunk port ( is green in CTC )
I made Circuit OTHCC between 100G cards 100G Ethernet client port on both side.
Still I don't see any RX/TX power on 100G side ( on any LANE in SR Optics )
Please share you experience with running up such configuration ?
Anybody had problem with 100-SR Optics ?
Any tricky part in this configuration ?
FYI
To rull out the faulty part I have made
- changed MPO cables
- changed SR optics in ONS and also CFP in asr9000 ( I have few such boxes )
- changed 100G cards and also diferrent ports on asr9000
- changed ONS chasiss and also ONS 100G Transpoder card

Hi,
- Try create OCHCC not 100G, try use OTU4 may be it will helpful. And what is the status of ASR 9k port in CTC( I mean in CTC network view and choose Show Router Port Status > rack/slot/module/port.)
- Are circuit up inside DWDM network? Try to make photonic test in Properties of OCH-Trail. May be you didn't Lanch ANS or problem inside network.
- Also Try generate traffic! not ping.

Similar Messages

Connect Flash to Serial Port with Local Socket Connection

Hey all,
So, I am trying to connect a Flash movie to a serial port
and have it react to the input coming in. Of course, Flash does not
have this capability built in, so I need a workaround. I also
program in Director, and there are easier ways to deal with this
there, but since there hasn't been an update in years, and for
other technical reasons, I would like to use a pure Flash program.
I also need to take advantage of some of the new hardware
acceleration improvements and horizontal sync issues that come with
running the Flash player full screen. So, there are some tools out
there that will let me stream the input from the serial port to a
web address. I figure I could use the local address and assign a
port number, then use Flash to create a local socket connection. I
am having issues opening ports on my computer, and a few other
things, but in theory, I think it should work. I know that I won't
get all the answers here, but if anyone has done anything of the
sort, or might know of some similar projects, it would really help.
I am more of a Director/Flash programmer, and not so much one on
the system level. So, opening local sockets, etc, while I am sure I
can figure it out, is still a bit beyond me. Thanks all!
- Bruce

You may want to look into flash remoting, which would allow
you to push content to the flash movie. You could then write a
proxy between the source of your stream and flash the remoting
server.

DCN Case Study 3: ONS 15454 Linear Topology with DCN Connections at Both Ends Using OSPF

Hi, I need advise regarding design of Network Connectivity - DCN Case Study 3: ONS 15454 Linear Topology with DCN Connections at Both Ends Using OSPF.
Am I need area 100 and 200 on Router 1 and Router 2 or I can don't do that?
Am

ONS 15454 SDH with 2 ML cards connected to the same RPR

I was wondering if I could connect 2 ML cards installed in the same ONS 15454 to the same RPR ring. Thanks!

Bob,
If you are wanting to tie the ML100 and the ML1000 into the same RPR Ring, then you have do do it with the POS interfaces.
For Example:
ML 100 POS 0 - North Microwave
ML 100 POS 1 - connect RPR to ML 1000 POS 0
ML 1000 POS 1 - South Microwave
North Microwave connects RPR to South Microwave
This creates a single Loop or Ring
It sounds like you are using your ML1000 as a Spur to another location. In order to create an RPR ring, you must have the cards physically connected to each other in a continuous ring.
Aaron Reed
Carrier Escalation - Cisco Optical TAC

Can you Monitor an ONS 15454 with Mars?

Can you Monitor an ONS 15454 with Mars? Is there a specific "Device Type" to use in order to do this?

ONS 15454 is not a supported device on MARS.
Here is the supported platform on MARS for your reference:
http://www.cisco.com/en/US/docs/security/security_management/cs-mars/6.1/compatibility/local_controller/dtlc6x.html
Hope that helps.

Upgrade ONS 15454 M12 TCC2P from 9.4.03 to 10.0.11

Hello,
quick question.
I have in my lab one M12 subrack with only-one TCC2P card and I try to prepare software upgrade in customer network.
I read all procedures at: http://www.cisco.com/c/en/us/td/docs/optical/15000r/upgrade/guide/b-454a10-0-1-upgrade.html
My troubles started at point where I can select node where the software must be downloaded. The window is empty.
Target version is "ons15454.DWDM.Lite.K9.R10011.pkg".
Any idea?
Thanks
kvapa

Hi Emyrsonn,
I hope this ONS 15454 upgrade tool can help you answering all your questions
http://www.cisco.com/web/techdoc/optical/15000r/upgrade/guide/ons-upgrade.html
It seems like you should be able to directly upgrade from 9.1.x to 9.2.2.
Please let me know if you have any comments on that.
Hope it helps!

ONS 15454 error message

Hi Expert,
I have a problem with ONS 15454 error message. My CTM server detected MINOR error message "Peer to Peer Slot Communication Failure". Affected object is SLOT-1 which is OPT_BST. The alarm ID is 200551. What caused this error appear and any workaround to solve this problem?. Your kind attention is much appreciated.

Although the following alarm is not identical to the one you identified, this seems to indicate the a peer "communication failure" is hardware related.
2.5.237 PEER-NORESPONSE
Default Severity: Major (MJ), Non-Service-Affecting (NSA)
Logical Object: EQPT
The switch agent raises a Peer Card Not Responding alarm if either traffic card in a protection group does not receive a response to the peer status request message. PEER-NORESPONSE is a software failure and occurs at the task level, as opposed to a communication failure, which is a hardware failure between peer cards.
Hope this helps....

ONS 15454 design question

I have an ONS 15454 with 2 OC192 circuits that terminate into it. One goes to a downstream ONS and another to the upstream.
I need to extend the existing ring to 2 more ONS devices, but I am not sure if it is going to work the way I want it to.
Right now, each VTS24 circuit on the OC192 is associated with a POS interface on the ML1000 cards. So POS1 goes upstream, POS0 downstream (unprotected). The ML1000 is int turn trunked to a 3750 L3 switch that has the bridge groups and layer 3 addressing assigned. This is Ring0
I need to extend this ring, so obviously I will need 2 additional OC192 cards, but do these new circuits need to be associated with new POS interfaces? In other words, will I need 2 additional ML1000 cards, and if so, how would I trunk to the switch? Am I going to get into some loopy topology here?
I am new to this system, so any advice would be great.

Hi Colin,
so you want to add two more ONS devices in an existing ring.
if you can provide a topology it will be helpful,
if you just want to add two more ONS in existing ring, it will no cause any issues,
we just have to take care of circuits and need to build them from TL1 in these new nodes.
but please send topology to get an clear view.

Cisco ONS 15454 SDH

Hi,
i have 3 sites connecting together with SDH 15454 site A-B with STM-1 and from site B-C STM-16,i want to Aggregated hand-off E1's from Site A-C so site B will be trasparet site for this link.
to be source of link on site A and Drop on site C.
any help to achive this.
there is already cricte between site B-C.

You will need to verify that the cross-connect card in the ONS 15454 (sites B & C) have VC-12 grooming capabilities (XC-VXL and CX-VXC will support VC-12 grooming).
The ONS is designed to groom lower rate signals to higher rate speed lines. Thus, you should be able to aggregate the E1s from the ISPs STM1 with the E1s from Site B and drop them at Site C.
You will need to add an STM1 card(s) to Site B. Your ISP will need to provide the mapping structure of the STM1, so you can understand where the VC-12s, which contain the E1s, are located in the payload. You will then create circuits to map each E1 (the incoming VC-12s within VC3/VC4) from you ISPs STM1 at Site B, to the appropriate VC-12 on the outgoing STM16 line heading toward Site C. At Site C, you will need to map the VC-12s on the STM16 line to the appropriate port on an E1 line card.
I hope this helps. Otherwise, you will need to have someone locally assist you in the explanation.
Tom

ONS 15454 shows up as "unknown" after power outage

We had a power outage that took down a ONS 15454 in a remote facility. Upon restoring power and powering-up the unit, it shows up in CTC as grey with "Uknown2" as the name.
I had someone reseat the TCC card, but it still comes up as unknown.
Has anyone seen this? Any suggestions (the device is hours from me)

Try and restart CTC session and clear CTC cache
Can you ping the node
Check to see if the node is in the OSPF routing table
Can you access via CTC locally
Is your CTC terminal directly connected or does it go via a firewall
Probably resolved now how did you resolve it?

ONS 15454 Craft interface to a Cisco 2511 Terminal Server

Does anybody have pinout of wiring ONS 15454 craft interface to a Cisco 2511 terminal server? I tried many combinations but nothing seem to work.
2511 has octal cable with RJ-45 connector. I used an rj-45 coupler to connect a wire wrapped RJ-45 cable to craft interface.
Thanks,

Pin Field
Contact
Function
Craft
A1
Receive
A2
Transmit
A3
Ground
A4
DTR

ONS 15454 and AC/DC Converter for 220V

I am looking for a AC/DC converter for a ONS15454 for a 220V input.
The ONS 15454 datasheet indicate input current 22A maximum.
The Cisco AC/DC Power Solution datasheet indicate for ONS 15454 a medium solution.
And the same datasheet indicate the small solution is up to 32A for 220V.
Then, can I use the small configuration for ONS at 220V?
Anyone know that? Can you help me with that?
Graciela

What is the hardware configuration of your 15454 including chassis, fan and by slot?
Using the hardware config, you can calcualte the expected amperage.
http://www.cisco.com/en/US/partner/products/hw/optical/ps2006/products_tech_note09186a0080094ae4.shtml
The general power requirement of 22A provides for any possible configuration. Actual configurations may be less. I have some 454s using as little as 9A in the lab.

ONS 15454 MRC 2.5G4

Hi All,
We are trying to install the optical multirate card (MRC 2.5Gig) on ONS 15454 and found the card comming up on standby state instead of active. The version running on the sonet box is 8.5.0 ...The MRC card port 1 is installed with the OC3 SFP's but cable not attached.
Any help would be appreciated .
Regards
Anantha Subramanian Natarajan

Hi, this is normal. Just go on and enable a SFP, called pluggable port module (PPM). After the first SFP is enabled, the state of the MRC card will change to working.
Cheers
Rene

ONS 15454 Training

I am looking for cbt or knowlegeNet like traning video for the ONS 15454? Is such available? I am happy to pay :)
Francisco.

Take a look at the offerings listed at http://www.cisco.com/web/learning/le31/ase/offerings/optical/index.html
These courses are offered by partners - Global Knowledge seems to be doing most of the ONS classes. According to a search I did just now, "Cisco ONS 15454 Turn Up, Test, Provisioning, and Operation Training (OCTPO) v7.0" is being offered at several locations in the USA and Canada this year.
Other than the classroom-based training, I'm afraid your alternative is to slog through the manuals in conjunction with hands-on experience as the only alternative. Personally, I'd not recommend that path unless you have an experienced mentor to guide you along. There're a good number of complexities that are difficult to discern without guidance.
Hope this helps. Please rate helpful posts.

ONS-15454 V8.5 and SNMP V2c

Can someone tell me if the ONS-15454 support INFORM Traps?
I'm trying to get INFORM Traps working with my NMS, but I don't think it's working. Either I don't have it configured correctly or its supported on the ONS.
Many Thanks

You are correct. INFORM Requests are different from TRAPS. Both are sent from the monitored device to the SNMP Manager. Both advise the SNMP Manager of an event that has occurred. The difference is the INFORM Request requires a response from the SNMP Manager while a TRAP does not. The INFORM Request allows the monitored device to know that the SNMP Manager has received his message.
Now to the ONS... it supports TRAPS, but not INFORM Requests.
Mike Dooley
Cisco Heartland TAC

ASR9000 100G-SR with ONS-15454 100G-LC-C - problem with local SR connection

Similar Messages

Maybe you are looking for