Assign Resources to all ISA Error

Hey guys... Since this is the most indescriptive error ive ever seen im gunna need some help. Just built the computer and only have a master harddrive, and videocard in there. The D-Bracket is reading the "Assign Resources to all ISA" error which doesnt seem to stop the computer from doing things, but i can hear it crunching away at something. If i let it sit it will eventually respond like 10min later at which point it continues to run incredibly slow. I have tried clearing the CMOS and it works, but does not solve the problem. The keyboard is the only device hooked up and it is nonUSB. I know the keyboard is good because it does repsond to keypresses like i said, just very very very slowly. Any ideas on what is causing this and what i can do to fix it?
Thanks
BTW
Athlon 64 3000+
K8N Neo Platinum
Corsair TwinX 3200
ATI x800XT
Western Digital 80gig 7200RPM (set as master)
No Floppy

Problem Solved
Heres what the problem was for those of you that also dont understand cryptic messages. I had my HD hooked up as the only device on the cable set as Master. Apparently the motherboard doesnt like it set that way. To solve the problem (in this case) just set the jumper to Cable Select and everything will be fine. The drive is a Western Digital so it might just be localized to that drive. I saw in my searches for a solution that 2 people had the same problem but caused by their cd drive. So if you happen across this error, check your jumpers it seems to be the root of the problem from what ive gathered/experienced.

Similar Messages

'Assign resources to all ISA' Error (Neo2 Plat.)

finally put all my new components together on my new MSI Neo2 Platinum board. however, its locking up shortly after boot. Using the MSI D-Bracket, it's telling me its locking on the 'Assign resources to ISA' step. my component are below, but the only things i have plugged in or powered on are the SATA HD's, RAM, Vid Card, SB Audigy2.
amd athlon64 3000+
512MB Kingston HyperX 3200
12x8x16 Plextor DVDRW
72x Kenwood CDROM
40x12 Plextor CDRW
2x Western Digital 80GB HD (SATA)
Albatron geforce4 4600
SB Audigy2
any ideas as to what would be causing this? ive owned several MSI boards and never seen this error.

got it to get past that stage, seems it was a cdrom. however, ive run into more problems with this setup than anything ive ever worked on. still working on it now. glad i didnt take apart this computer yet...

Assign Resources to all ISA / Possible VGA Problem

Pentium 4 2.8GHz
MSI VIA PT8 Neo-V
2x elixir 512mb DDR400
6600LE AGP8x 256MB TV-OUT DVI
Maxtor Diamond Max Plus 9 80GB ATA 133
Raid Card (no info)
Creative Labs Soundblaster Audigy LS
Chieftec 340W 230V
XP Pro
I recently had problems with my machine where it kept freezing during windows start up. I changed hard drives, managed a new XP instalation. But then it started freezing again. The last couple of tiems I turned it on, it wouldn't do anything except report a disc error.
I have removed every device in the machine, everything 1 by 1. Plugging only one thing in, but I get the same light on the d bracket every time. The error lights means 'Assign Resources to all ISA'. I have tried clearing the CMOS with and without devices in.
I also get a series of bleeps, which I think is 2 very quick bleeps, followed by 8 short bleeps

well Now I can get it to boot, but still no video. It makes a funny beep when the upper left corer of the d bracket is green.

Assign Resources to all ISA ..no post

Hi,
I can't search for this topic on this forum, I get an error response every time.
MS-7030 with a Atllon 64 3200+ on an anted true power 430 supply, one WD hard drive and a 5700 Ultra video card. 2 PNY 512MB sticks on 2 and 3 slot.
Get error code Assign Resources to all ISA , when booting up. I get to the screen saying "tab for POST, del for BIOS setup" but can't do anything from there.
Is the MB bad? anybody else solved this problem?
Help would be very, very greatly appreciated.
Thanks,
Alfred

Thanks very much for you reply.
I finally found the problem. I'm embarrased to say, I forgot to change from master to CS on my WD hard drive.
thanks,
Miron

Assign Resources to all ISA

Arg, I am getting this erro,Assign Resources to all ISA,r after switching video cards in my computer. It only happens with the X800 pro and not the 9800 pro. I have gone back and forth between the 2 a few times. With the same results. BTW this is on a k8n neo plat 3400+, 3700eb, true control 550 24A-12v 40A-5V 32A-3.3V. I also have audigy 2 and rocket raid 404 pci cards connected.

well Now I can get it to boot, but still no video. It makes a funny beep when the upper left corer of the d bracket is green.

Assign resources to all ISA - hang

Hi all,
i recently made 2 new computers with this specs:
K8N Neo2Platinum
A64 3200+ (939)
A-data 2*512 MB 400 MHz
Ati X800 PRO
Maxtor SATA 200 GB
PSU: no name 350 W, +3,3 - 15A, +5 - 15A, +12 - 9A
or alternative (i have changed it), no name psu, 300W, +3.3 - 28A, +5 - 30a, +12 - 15A
One of this computers have some instability problem a now even wont start up. D-led shows: Assing resources to all ISA. I would like to ask what does it mean?
I know my psu are creapy (i hate these garage sales companies, which sell around here ). First i thing the problem will be in psu, but the second computers have the same specification and its running perfectly.
Please help me.
dwayne

Quote from: lef on 03-September-06, 05:21:28
Hi , i realy need to know is what that D-led statment: assing resources to ISA means . Why? Becouse this problem realy @!?#ed me Please Help me. my Pc is running normaly before and now D-led show assing resources to ISA ... LOL i hawen´t ISA ! .The same trouble as dwayne_stone .I run pc with only memory graf card and CPU. Thanx
Every PC still has ISA resources: keyboard, mouse, text-mode video, floppy drive, RTC, COMs, LPT... As far as I see, none of you have mentioned BIOS version nor whether you tried to clear CMOS nor whether the keyboard lights flash or you get a beep. The "resources" the msg refers to are IRQs, I/O addresses and possibly DMA channels which are all fixed for the system ISA devices. Start by disconnecting all non-essential devices; next try swapping external devices, e.g. keyboard, mouse... just use a different keyboard & mouse and then try switching the interface PS/2<->USB.

Assign resources to all ISA and garbled graphics on boot.....any suggestions?

Subject says it all. I boot up and get the above mentioned error from the LED bracket. If i could see clearly enough i could mess around in the bios.... I just replaced the MOBO, PSU and video card and this is the first attempt at rebooting it with the new components (exact same components just factory new).
UPDATE: I can get it to boot up to windows now but the graphic display is still messed up although i can see when im in windows. When I use an old video card (geforce 2) It works pretty much like normal with no graphic errors. With either video card in I get no LED errors when im finally in windows.
Could the new motherboard and video card with old HDD and winxp loading on it be causing the graphics issues? I will try a fresh install of winxp and see if that fixes it. Until then, any suggestions or comments would be appreciated. Thank you!

Thanks for the replies. All the components i just put in were the same exact components, I just did RMA for replacements because I had a power surge or something and things went bad. Maybe I just got lucky with the maddog crap psu for a year. I did have a thermaltake 420 watt PSU but it caused problems and I tried the maddogg and it worked fine so I assumed it was better quality than thermaltake. Would poor PSU cause the graphics card to display funky? makes since that I put in the small video card and it works fine....maybe ill try putting in the RMA'd thermaltake 420 PSU again. Thanks again
Also...No, I haven't done a clean install of windows yet because I wanted to start up and save some important data from the HDD then I was planning on doing a clean install after that.

Error Message while assigning resource to work orders

Hi All,
We have the MRS tool integration with service work orders for scheduling. When we assign the resources with 9 hours as duration there is no error. When we allocate more than 9 hours for some resources, not all, we receive the error message as
" Duration    29,160 S is not a multiple of 15 minutes " . These duration of secs varies when the duration is varied > 9 hours.
We have checked the planning board profile configurations but nothing seems to be visible. In customising we have the following settings,
Time Granularity                 : 15 mins
Min duraiton of assignments: 15 mins
Automatic Assignment Splits
Min duraiton           : 2 hours
Max overtime hours : 2 hours
Max Ratio is %       : 75
Can anyone throw some light on this?
Regards,
Selva

Hi Anil Satya,
The MRS is integrated with Service Order types and the operations are selected for each order then the assignment of hours takes place in MRS.
If the assignment is done for 9 hours then there is no such error. These errors are very specific to some personnel numbers ( not for all ) where the duration is more than 9 hours.
Is there any availability of resources for this operation / job through configuration settings? Why such a question is some resources even when 15 or 20 hours is assigned , no errors exists.
Hope this explanation provides a better clarity.
Regards,
Selva

Getting dump while assigning resource to role

Hi,
We are using BAPI_BUS2177_STAFFING_ADD to assign resource to role.
It is assigning first resource to first role in first project. And giving dump for next resource to role assignment for the same project.
Short dump description is like as follows:
The exception 'CX_DPR_FATAL_ERROR' was raised, but it was not caught anywhere
along
the call hierarchy.
Since exceptions represent error situations and this error was not
adequately responded to, the running ABAP program
'CL_DPR_AUTHORIZATION_SERVICES=CP' has to be
terminated.
The problem is of "COMMIT". I ma not understanding where to write exact commit. Even if we are commiting at project level it is giving dump.
Could you please give any suggestion on it.
Thanks & Regards,
Anil Salekar

Hello Kaixiang,
When you add staffing to project then commit after each resource assignment. That will avoid the dump.
Use:
CALL FUNCTION 'BAPI_CPROJECTS_COMMIT_WORK'
TABLES
return = it_return.
Note: Re award if useful
Thanks,
Appasaheb..

Need urgent help :'The requested resource does not exist error'

Hi All,
I am getting 'The requested resource does not exist error' when trying to acess http://machinename:50000/irj
Even when i access http://machinename:50000, i get the same 'The root directory does not exist' error. I checked in visual admin, there is no other application deployed except my application.
Any clues? Pls help
thanks
bhawna

HI ,
Did succeed to solve your problem. I am running into same problem.
Any help is welcome.
Thank u very much.

How to identify what are all the errors appears in process chain,

Hi all,
i have a process chain running, but i want to find out what are all the errors that the process chain has thrown
thanks
pooja

Hi Pooja,
Errors in monitoring:
SID error
Reason: If the corresponding master data is missing for the particular transaction data.
         1. Check for the load timing for the respective master data, if it less than an hour then make the request red and repeat the ip.
         2. If the data is loaded to PSA then you have to delete the request from target and manually push the data to from PSA.
         3. If we are required for selective update then note down the info source from header and find it in RSA1,select the one with Single as postfix.
         4. Goto data selection tab and change the range.
Tip: change the last 4 digits for from to 0000and the last 4 digit for to     9999.
        5. Repeat the ip.
         6. In case only of failure in one target goto RSA1 find the PSA, put he request no. and reschedule it.
Note: IF PSA is present never make the request red rather delete it.
Replication error
Reason: Data source replication Failed.
         1. In order to handle this error you should be known to IP, info source and source system.
         2. Goto RSA1, find the data source in the source sys tab.
         3. Right click on the data source and replicate it.
         4. Since all the transformation rules pertaining to this data source need to be reactivated so go to SE38 and execute rs_transtru_activat_all, data source and sys name.
         5. Delete the red request from the target.
Update R not supported
Reason: The corresponding initialization flag for the ip is lost.
         1. Goto header click on the ip and goto schedule tab and click initialize in the source system, whatever screen appears delete the only request present(the initialization flag).
         2. Goto RSA1, find the ip in the info source (one with the Adhoc initialize flag).
         3. Goto update tab and select Initialize delta process try going for with data transfer.
         4. Reschedule the IP.
Duplicate Record Error
Reason: Duplicate error records for the loaded master data.
         1. Goto info package via header or via RSA1.
         2. Goto processing tab and change the ip setting, selecting only PSA and ignore duplicate records and re run the ip.
         3. Do remember to change the ip settings back to the original once after the second step.
ODS activation failure
Reason: Prerequisites for ODs activation not satisfied i.e. unique key.
         1. Goto maintain variant.
         2. Check for the QM status of the requests in the target they should be green.
         3. Then click the ODS activation tab.
         4. In the screen which appears put the requests for which ODS activation failed.
         5. Activate these and keep on refreshing them until status reverts from green,
Remember to refresh these requests one at a time.
         6. If requests are red then delete them from target.
         7. Reschedule the IP.
Note: Never Try activating ODS manually if it is Y1.
Aggregate Rollup error
Reason: No aggregate found for the respective rollup.
         1. Click on the variant in which the error occurred.
         2. Goto chain tab and copy the variant and instance.
         3. Run the nestle provided program YBW05.
         4. Put in info in there and put the status as g green.
         5. Execute and refresh the status.
Lock issue
Reason: The same ip is been locked by other user or may be used by other process chain.
         1. We can see the locked entries and in the transaction SM12.
         2. Wait for the other process to get complete once the ip loads to target in that process then there is no need for running it for the process.
         3. In other case make the request red, when PSA is present then goto environment tab ->schedule->initiate update.
         4. In the box appears select update in the background.
         5. And the manually update the failed IPs by selecting manual update in the context menu.
Alfa confirming value error, Time conversion error, Chain didnt start, Delay due to long running job, Poor system performance,Heirarchy node exist in duplicate.
Reasons:
Alfa confirming error: Data format mismatch.
Time conversion error: Date, time format mismatch.
Chain didnt start: A scheduled chain didnt triggered at the prescribed timing.
-For all the above error we have to raise a ticket.
Idoc or TRFC error
Reason: An Idoc is been stuck somewhere.
         1. Reload the Master Data manually again from Info-package at RSA1.
         2. Release the Idoc.
         3. In the source system level got environment->transaction->Transaction RFC or Data ware housing level.
         4. In the Screen if the status is Transaction Recorded it means its stuck goto edit and click Execute LUW or press F6.
         5. If status is Transaction executing then it means its fine wait.
         6. Or raise ticket.
Error Due to short Dump
Reason: Error due to Short dump could be due to many reasons i.e. memory, table space, lock, error record, page allocation, failed change run.
Process terminated in the Source system.
           Reason: Sometimes we face that a load has failed due to job Termination at Source System.
      This happens due to unavailability of the source system or some connectivity problem between source and target systems.
1.      Make the request red.
2.      Delete the request from the data target.
3.      Reschedule the ip.
4.      If still the job fails raise the ticket.
And also check in following links:
Process Chain Errors
/people/mona.kapur/blog/2008/01/14/process-chain-errors
Common Process chain errors
For Data Load Errors check this blog:
/people/siegfried.szameitat/blog/2005/07/28/data-load-errors--basic-checks
Pls assign points if it helps u,
Thanks & Regards,
Madhu

All validation error from saxParser.parse

I am getting just the 1st error but I want all the errors in the 1st pass itself.
Attaching the code for reference also.
?would really appreciate you suggestion.
==code---
public class EDITExtractSchema {
static Document document;
public void validateXMLVOusingXSD(String str)
try {
//create a SchemaFactory capable of understanding W3C XML Schemas (WXS)
SchemaFactory factory = SchemaFactory.newInstance("http://www.w3.org/2001/XMLSchema");
//Set the error handler to receive any error during Schema Compilation
XMLErrorHandler errorHandler = new XMLErrorHandler();
factory.setErrorHandler(errorHandler);
//set the resource resolver to customize resource resolution
//factory.setResourceResolver( new MyLSResourceResolver());
// load a WXS schema, represented by a Schema instance
File schemaFile = new File("C:/Temp/project2-CorrVO/XSDs/TaxExtract5498DetailVO.xsd");
Schema schema = factory.newSchema(new StreamSource(schemaFile));
SAXParserFactory spf = SAXParserFactory.newInstance();
//spf.setNamespaceAware(true);
//spf.setValidating(true);
spf.setFeature("http://apache.org/xml/features/validation/schema-full-checking", true);
//Just set the Schema instance on SAXParserFactory
spf.setSchema(schema);
//Obtain the SAXParser instance
SAXParser saxParser = spf.newSAXParser();
//parser will parse the XML document but validate it using Schema instance
//saxParser.parse(new File(str), myHandler);
saxParser.parse(new File(str),new MyDefaulyHandler());
}catch(ParserConfigurationException e) {
System.out.println("ParserConfigurationException-" + e);
}catch (SAXException e) {
System.out.println("SAXException-" + e);
catch (Exception e) {
System.out.println("Exception-" + e);
/*// output the errors XML
XMLWriter writer = null;
try {
writer = new XMLWriter(OutputFormat.createPrettyPrint());
} catch (UnsupportedEncodingException e) {
System.out.println("validate error" + e);
e.printStackTrace();
try {
writer.write(errorHandler.geterrors());
} catch (IOException e) {
System.out.println("validate error" + e);
e.printStackTrace();
//implement error handler
public static class XMLErrorHandler implements ErrorHandler {
private boolean valid = true;
public void reset() {
// Assume document is valid until proven otherwise
valid = true;
public boolean isValid() {
return valid;
public void warning(SAXParseException exception) throws SAXException{
System.out.println("Warning: " + exception.getMessage());
System.out.println(" at line " + exception.getLineNumber()
+ ", column " + exception.getColumnNumber());
System.out.println(" in entity " + exception.getSystemId());
valid = true;
public void error(SAXParseException exception) throws SAXException{
System.out.println("Error: " + exception.getMessage());
System.out.println(" at line " + exception.getLineNumber()
+ ", column " + exception.getColumnNumber());
System.out.println(" in entity " + exception.getSystemId());
valid = true;
/* // output the errors XML
XMLWriter writer = null;
try {
writer = new XMLWriter(OutputFormat.createPrettyPrint());
} catch (UnsupportedEncodingException e) {
System.out.println("validate error" + e);
e.printStackTrace();
try {
writer.write((Object)exception);
} catch (IOException e) {
System.out.println("validate error" + e);
e.printStackTrace();
public void fatalError(SAXParseException exception) throws SAXException {
System.out.println("Fatal Error: " + exception.getMessage());
System.out.println(" at line " + exception.getLineNumber()
+ ", column " + exception.getColumnNumber());
System.out.println(" in entity " + exception.getSystemId());
valid = true;
public static class MyDefaulyHandler extends DefaultHandler {
private boolean valid = true;
public void reset() {
// Assume document is valid until proven otherwise
valid = true;
public boolean isValid() {
return valid;
public void warning(SAXParseException exception) throws SAXException{
System.out.println("Warning: " + exception.getMessage());
System.out.println(" at line " + exception.getLineNumber()
+ ", column " + exception.getColumnNumber());
System.out.println(" in entity " + exception.getSystemId());
valid = true;
public void error(SAXParseException exception) throws SAXException{
System.out.println("Error: " + exception.getMessage());
System.out.println(" at line " + exception.getLineNumber()
+ ", column " + exception.getColumnNumber());
System.out.println(" in entity " + exception.getSystemId());
valid = true;
/* // output the errors XML
XMLWriter writer = null;
try {
writer = new XMLWriter(OutputFormat.createPrettyPrint());
} catch (UnsupportedEncodingException e) {
System.out.println("validate error" + e);
e.printStackTrace();
try {
writer.write((Object)exception);
} catch (IOException e) {
System.out.println("validate error" + e);
e.printStackTrace();
public void fatalError(SAXParseException exception) throws SAXException {
System.out.println("Fatal Error: " + exception.getMessage());
System.out.println(" at line " + exception.getLineNumber()
+ ", column " + exception.getColumnNumber());
System.out.println(" in entity " + exception.getSystemId());
valid = true;
public static void main(String[] args) {
EDITExtractSchema schemaClass = new EDITExtractSchema();
try {
schemaClass.validateXMLVOusingXSD("C:/Temp/project2-CorrVO/XSDs/TaxExtract5498DetailVO.xml");
}catch (Exception e) {
System.out.println("xml file read error Exception-" + e);
--====
Regards,
Tapas

No really, it will report all the error if you turn on the validation and implement the error hander methods(error()).
ALSO,
My XSD had "<xs:sequence>" which was causing the problem.
We had to change it to "<xs:all>". Now all the errors are getting reported.
thx!

CRS-0223: Resource x has placement error.

hi all
i have rac 11.2 rhe5 over asm
database stopped running
as i guess asm has problem. i can read and write files on it but oracle instance cant
i tride to restart resource but i have an eroor
CRS-0223: Resource x has placement error.
can someone help me ?

Dear soso_xuc,
It is impossible even for a highly skilled artificial intelligent device to analyze your problem with the given details below;
+"+
+error occurs+
+saying can't identify some file on asm+
+"+
Regards.
Ogan

Standard ABAP functions for assign resources?

Hi all.
I would like to share this with you all.
After loosing three days looking for any kind of standard FM to assign resources (rooms or instructors) to an event (E), I request your help.
Any of you have found or used those functions in SAP?
Thanks in advance for your support.

Hello Roberto:
the FM we're using is HRIQ_EVENT_CREATE, not very creative , but we found nothing more appropriate, and we found it very flexible to work with events (unluckily flexible is a synonym of complex and hard work).
Let's move into when and how we used it:
regular courses are still created using SAPgui
we needed something more agile to use when a room or resource was needed for unusual activities (meetings for example), and no instructors were needed. We went into a web app. The user will indicate date(s), start and end time and resource. We developed a FM+webservice which "receives" the data inserted by the user and ends executing HRIQ_EVENT_CREATE. (precondition: we have a generic module created with its correpsonding event type needed to execute HRIQ_EVENT_CREATE)
a previous step to the event creation (on a separate FM+webservice) will check for conflicts in the proposed resource reservation, where the user will see a report of conflicts and make necessary changes before submitting the reservation.
Would you like to see our codes? Part of it is in Spanish which'll help you read the code
Cheers,
Michael

Project 2013 No Server, No Sharepoint, Updating Tasks From Assigned Resources Through Email

Ok,
I have searched high and low for this type of information and Im surprised after all these years that no one has asked or requested this type of information?
I am a consultant, with my own version of Project 2013 to track how I run Projects. This is the tool I use. So this being the case it makes no sense for me to spend millions of dollars for Project Server. I am just one person useing this
as my tool of choice.
My issues are:
I create and assign a task to a resource with a name and an email address.
I litterally have thousands of tasks with hundreds of assigned resources (People) with an email address.
I need to update weekly all my task!!! The entire point of using Project 2013 as a tool!
However it appears Microsoft needs to make this very dificult to do. If I have to manually email all these people with task and manually ask them for an update, then manually update all these task then whats the point of even bothering using Micrsofts Project
2013? It is useless.
I need a way to automate these updates without having a Server.
The Question no one seems to be asking is this?
Is there a way to update task through email, (Outlook), Why cant I send emails with a table of tasks assinged, request update in the task table, then the assigned resource sends me back the email with thier updates and I can automatically update my Project
Task?
Am I the only one who has asked this or thought of this? Or are my expectations to high? I cant figure how Microsoft could ever expect a single user of Project even with only one project with 50 to 100 task listed to have to get on the phone or emal
every single person manually, and manually update every single task every single week? I have used other Project type apps and they all have a way of sending emails out to assigned people to get task updates automatically. Only Project doesnt!
Why?

Thanks Prasanna,
Really for the amount of money I have to pay for a Product that should have some way to update tasks.
Think about this for minute. I believe Project 2007 was able to do this ,,,, that made sense....
Really ponder this question: What is the purpose of Microsoft Project for a single user? Does anyone ask these questions prior to development?
The reason for Project to exist is to TRACK TASK! THATS IT! Why would anyone want to track any type of task, hundreds of task MANUALLY? It does me no good for me to be the only one tracking task. It does me no good for me to be the only
one looking at the task schedule. Great, so IM THE ONLY ONE WHO KNOWS WHATS GOING ON?
So I ask this question.
If this is the case then what is the point of tracking anything if it cant be shared or updated in some way or another? Microsoft Project is useless as a single use product!
Here is the kicker....
I can purchase Outlook for a lot less, I can track any and all task, assign task to anyone with an email, I can assign and schedule task through Outlook and place an alert, set it as an appointment through the Calendar, change and assign start and end dates,
and get updates through email on any task, calendar, anything.... Why then would I waste ANYTIME OR MONEY ON A USELESS TASK TRACKING PRODUCT LIKE PROJECT? It does not do anything? Outlook does a thousand times more than Microsoft Project!
Does that make any sense to anybody? All Microsoft Project really is... is a stripped down Calendar/Task from Outlook with no ability to email, or communicate in any way shape or form with other people who are assigned the work. What ends up happening
is Microsoft expects single users to purchase Project Server? Are you crazy? This is the single reason why Project does not sale! If Microsoft would go back to sales metrics of Project 2007 they would see a decline till now that will reflect
this problem. Its really a simple fix. Sales would triple. Until there is a solution it makes way more sense for me to use Outlook, schedule work task on others calendars and have them send me an update weekly through an automated spreadsheet
through Outlook. From there all the reports exist in Excel. Why do I need Project anymore? BTW I have been a MS Project user since its inception.... SO IM not new to it... what a terrible waste of time, resources, and lack of
vision for just a simple powerful addin that was removed after 2007. Single users like myself will never purchase Project Server just so we can send emails with assigned task for an update,,, silly?

Assign Resources to all ISA Error

Similar Messages

Maybe you are looking for