Assigning a host name in the router

How do you assign a host name to a device that was discovered with a static IP address?
Router is a mi424wr-gen3i .

This thread may help you:
http://forums.verizon.com/t5/FiOS-Internet/Static-IP-Address-for-NAS-Network-Attached-Storage/m-p/57...
Enjoy!
If a forum member gives an answer you like, give them the Kudos they deserve. If a member gives you the answer to your question, mark the answer as Accepted Solution so others can see the solution to the problem.

Similar Messages

We installed a new router and changed the name of the router. Now my HP C4500 printer won't print.

Our cable company installed a new wireless router and changed the name of the router. Now my HP C4500 printer won't print from my laptop.
I can't find any ot the Set Up stuff I used initially.
Is there any way to get my printer to work again...wirelessly?

Get the latest software for your printer from the "Support & Drivers" link at the top of this page. When you start the installation it will ask what kind of installation you would like. Choose "Wireless" or "Network" then click "Next".
Eventually it will ask you to plug in a USB cable to the printer temporarily to communicate the new router's info to the printer. Make sure to not plug in the USB until it asks.
Say thanks by clicking "Kudos" "thumbs up" in the post that helped you.
I am employed by HP

Changing the host name of the server - impact on old Urls

All,
We are in the process of moving data centre and as part of this the host names of the BW servers will be changed and pointing to the new IP address, how and what configuration at BW server level to make sure all web reports points to the new host name when the url is generated.
Thanks

looked at the note 805344 and that helped me to understand...

Getting the host name in the email subject line

I am running SCOM 2012. Is there a way to have the host name of the server in the Subject line of an email?

As alerts dont always have a servername included. ie Alerts usually have the name of the server or source included in Source or Path you might want to include both in the subject.
Here is what we use but you can add the lines found in the body to the subject:
Source: $Data[Default='Not Present']/Context/DataItem/ManagedEntityDisplayName$
Path: $Data[Default='Not Present']/Context/DataItem/ManagedEntityPath$
Cheers,
Martin
Blog:
http://sustaslog.wordpress.com
LinkedIn:
Note: Posts are provided “AS IS” without warranty of any kind, either expressed or implied, including but not limited to the implied warranties of merchantability and/or fitness for a particular purpose.

Retrieve the host name behind the radware url

Hi,
Is it possible to retrieve the host name behind the radware url in BI Publisher template?
Thanks, R.

Hi,
Did you maintained the entry in below format
12.123.23.23 srstfdf srstfdf.shouse.com
in hosts file. If it is already maintained in the above format. then check the error if it is DNS related maintain the entry in DNS.
thanks,
madhu

Change IP and Host name of the server

Hi,
Db :11.2.0.3
Os:Aix6
OS team are going change IP address and host name of the server which has ASM and DB.
What are the things we need to follow for this?
Thanks & Regards,
VN

OS team are going change IP address and host name of the server which has ASM and DB.
What are the things we need to follow for this?1. TNSNAMES.ORA files everywhere
2. LISTENER.ORA on server
If there are thin JDBC clients, change IP/hostname in their connection URLs.

HT201320 I have an email account through yahoo. I am having trouble setting it upon my iPhone and can't receive or send emails!!!! I contacted Rogers and they said I need to find out the host name of the incoming server, in other words yahoos host name. H

I have an email account through yahoo. I am having trouble setting it upon my iPhone and can't receive or send emails!!!! I contacted Rogers and they said I need to find out the host name of the incoming server, in other words yahoos host name. Help!!

Yahoo's servers are notoriously unreliable. Use the "Yahoo" account type when setting it up. If it doesn't work, and you are positive the credentials are correct, wait a while and try again.
While you're waiting, set up a free gmail or iCloud email account.

How do I "scan" my LAN and find the host name of the server computer?

I need to scan my LAN to find out the IP and host name of the computer in which is waiting for client acceptance because the server side of my program is not always on the same computer. Therefore, the IP and host name of my server is not final and can be placed on any computer on my network with over 50 connected computers. How might I check to see which computer is waiting for a client?
EDIT: I need the host name only, disregard IP
Thanks!

watwatacrazy wrote:
jwenting wrote:
Peter__Lawrey wrote:
If you know the port you can try to connect to each of the machines in turn.the people getting firewall warnings about intrusion attempts would just love that, as would the network admins whose network you're clogging with traffic (imagine several hundred clients doing that all day long, let alone tens of thousands).
If they are all one the same subnet you can use the IP addresses.Which you don't necessarilly all know. Or do you propose just sweeping through all possible IP addresses in the subnet's range? That would be a sure trigger for your network admins to immediately kick you out.
This should take a few seconds at most.Until the automatic safeguards kick in and you're thrown off the net :)In that case, what would you suggest?Not to bother. The server address should be part of the application configuration, not guessed at runtime.

GRE tunnel could not be used by the hosts connected to the router

Hi,
I am using cisco ASR1013 (RP2) and a Mikrotik Router for setting up a GRE tunnel for LAN to LAN routing over a broadband link. The tunnel works fine (able to ping tunnel end points and also all the connected interfaces on both the Mikrotik and Cisco ASR) but the hosts that are connected directly to the Cisco router interface over a layer 2 cisco switch are unable to connect (ping) the hosts or connected interfaces on the mikrotik side. I am sure its not a mikrotik issue as i dont see any traffic coming through the tunnel using the mikrotik torch utility. There are no ACL's or firewall rules on any of the devices......
Source and destination of the tunnel are public IP's and are pingable via internet (The tunnel is connected and endpoints are pingable)
Mikrotik connected interface IP = 192.168.253.1/24
Mikrotik tunnel end point IP = 192.168.254.1/30
Cisco tunnel end point IP = 192.168.254.2/30
Connected cisco subnet to reach Mikrotik = M.N.O.32/28
Cisco interface IP for LAN = M.N.O.33
Test host IP on the LAN subnet = M.N.O.34
The below is my Cisco config
ASR-1#sh run int tun 1
Building configuration...
Current configuration : 144 bytes
interface Tunnel1
ip address 192.168.254.2 255.255.255.252
ip mtu 1400
tunnel source A.B.C.D
tunnel destination W.X.Y.Z
end
ASR-1#sh run int g0/1/7
Building configuration...
Current configuration : 280 bytes
interface GigabitEthernet0/1/7
description LAN
ip address M.N.O.33 255.255.255.240
ip verify unicast source reachable-via rx
no negotiation auto
cdp enable
end
ASR-1#sh ip ro 192.168.253.1
Routing entry for 192.168.253.0/24
Known via "static", distance 1, metric 0 (connected)
Routing Descriptor Blocks:
* directly connected, via Tunnel1
Route metric is 0, traffic share count is 1
ASR-1#ping 192.168.253.1 so M.N.O.33
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 192.168.253.1, timeout is 2 seconds:
Packet sent with a source address of M.N.O.33
Success rate is 100 percent (5/5), round-trip min/avg/max = 5/5/6 ms
ASR-1#pi M.N.O.34
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to M.N.O.34, timeout is 2 seconds:
Success rate is 100 percent (5/5), round-trip min/avg/max = 1/1/1 ms
If i try to ping 192.168.253.1 (network connected to Mikrotik) from the host M.N.O.34 (the gateway of this host is M.N.O.33 - Int g0/1/7 of the Cisco ASR), i cannot reach detination - request timed out.... Below are the results of trace and ping from the host connected to ASR G1/0/7
PING TO THE GATEWAY *********
[root@localhost ~]# ping M.N.O.33
PING M.N.O.33 (M.N.O.33) 56(84) bytes of data.
64 bytes from M.N.O.33: icmp_seq=1 ttl=255 time=0.161 ms
64 bytes from M.N.O.33: icmp_seq=2 ttl=255 time=0.143 ms
^C
--- M.N.O.33 ping statistics ---
2 packets transmitted, 2 received, 0% packet loss, time 1357ms
rtt min/avg/max/mdev = 0.143/0.152/0.161/0.009 ms
PING TO THE TUNNEL END POINT IN CISCO ASR
[root@localhost ~]# ping 192.168.254.2
PING 192.168.254.2 (192.168.254.2) 56(84) bytes of data.
64 bytes from 192.168.254.2: icmp_seq=1 ttl=255 time=0.141 ms
64 bytes from 192.168.254.2: icmp_seq=2 ttl=255 time=0.141 ms
^C
--- 192.168.254.2 ping statistics ---
2 packets transmitted, 2 received, 0% packet loss, time 1739ms
rtt min/avg/max/mdev = 0.141/0.141/0.141/0.000 ms
PING TO THE TUNNEL ENDPOINT IN MIKROTIK
[root@localhost ~]# ping 192.168.254.1
PING 192.168.254.1 (192.168.254.1) 56(84) bytes of data.
^C
--- 192.168.254.1 ping statistics ---
11 packets transmitted, 0 received, 100% packet loss, time 10413ms
PING TO THE CONNECTED INTERFACE ON MIKROTIK
[root@localhost ~]# ping 192.168.253.1
PING 192.168.253.1 (192.168.253.1) 56(84) bytes of data.
^C
--- 192.168.253.1 ping statistics ---
4 packets transmitted, 0 received, 100% packet loss, time 3641ms
TRACE TO THE CONNECTED INTERFACE ON MIKROTIK
[root@localhost ~]# traceroute 192.168.253.1
traceroute to 192.168.253.1 (192.168.253.1), 30 hops max, 60 byte packets
1 M.N.O.33 (M.N.O.33) 0.180 ms 0.156 ms 0.145 ms
2 * * *
3 * * *
4 * * *
5 * * *
Please help

Hi,
Sorry for the delayed response ....Both ends static routes are added for the connected test interfaces.....
Regards,
Mahesh

How to set dynamic host name in the URL of a URL iView?

Hello,
I am using a standard URL iView that points to some J2EE app I've written and deployed on the same server.
I would like to set the host name to be a dynamic one, this way I won't need to change the iView URL when transporting it from one portal to another. As far as I know the system for a URL iView only controls authorizations but cannot replace the full URL set in the iView.
Any idea who can this be achieved?
Roy

Hi Mrityunjay,
forced URL at runtime will require me to call the URL iView from another iView that I will need to code (setting the URL in the Request object). If I did all this I might as well call it from this iView already.
I would like to do it with no further developments. I would have thought that SAP has constants that can be plugged in the URL for this type of thing, i.e. $hostname...
Rgds,
Roy
Edited by: Roy Cohen on Aug 21, 2008 4:03 PM

How to get host name in the workflow?

Hi,
I've a requirement where I need to get CQ Inbox url (http://<hostname>:<port>/inbox) in my custom workflow process. I thought of configuring url to some node and retriving from there.. but It's not the good approach as host name will be different for differnt CQ environments. So what is the best way of getting inbox url?
Env: CQ 5.6
Thanks
Siva

Yep Justin, If the configuration is wrong, any link generated would also be wrong.. I mean, default configuration will be some thing like..
I mean, I can change those configurations as per my instance host name, right?
Example: my instance's host url is: mytest:1501
So I would like to update the same in configurations ..

Getting host name of the remote client using getRemoteHost() --Problem

Hi everybody
Does anyone know how I can get the Host name out of the request ? I just get IP address which I do not need at all , any suggestion ?
Many thanks
Arash

If it has a name then
InetAddress addr = InetAddress.getByName("212.58.224.123");
System.out.println(addr.getHostName());

Assign Logical file name for the physical file path through Program

Hi all,
I am having a physical file which is getting generated dynamically. It is having the date and time stamp in its name which is added at runtime.
Now I need to assign a logical file name for the physical file path through the program.
Is there any FM or any other method to assign the same.
Gaurav

I think it is not possible. becuase the date & time added at runtime. so if you check the table PATH you can find filename and their definitions
a®

Host name in the getConnection statement.

HI,
I am trying to use JDBC to access Oracle database. I used the following statements to register the driver and get the connection:
DriverManager.registerDriver(new oracle.jdbc.driver.OracleDriver());
Connection conn=DriverManager.getConnection("jdbc:oracle:thin:@localhost:1521:test","SYSTEM", "manager");
I have the database called test. I can compile the code correctly, but when I run it, it says "Invalid Oracle URL specified". I am not sure what to use for the host name. I checked the listener.ora, and the port number is 1521. I have the oracle8.1.7 installed on my windows2000, so I believe it is running as a windows service. Can anybody tell me what hostname to use? Thanks a lot.

I tried to add the statement to the init.ora file which is referenced by the inittest.ora file, and the error message changed to the following: (By the way, am I supposed to modify anything in order to use JDBC, or it should be fine after it has been installed?) Thanks.
Exception in thread "main" java.sql.SQLException: ORA-01034: ORACLE not available
ORA-27101: shared memory realm does not exist
at oracle.jdbc.dbaccess.DBError.throwSqlException(DBError.java:168)
at oracle.jdbc.ttc7.TTIoer.processError(TTIoer.java:208)
at oracle.jdbc.ttc7.O3log.receive1st(O3log.java:428)
at oracle.jdbc.ttc7.TTC7Protocol.logon(TTC7Protocol.java:248)
at oracle.jdbc.driver.OracleConnection.<init>(OracleConnection.java:249)
at oracle.jdbc.driver.OracleDriver.getConnectionInstance(OracleDriver.java:36
5)
at oracle.jdbc.driver.OracleDriver.connect(OracleDriver.java:260)
at java.sql.DriverManager.getConnection(DriverManager.java:517)
at java.sql.DriverManager.getConnection(DriverManager.java:177)
at JDBCExample.main(JDBCExample.java:10)

Servername and virtual host name is the same - how to handle this

Hi,
I set up a server with the hostname yxzwiki.org
In the Server app under Websites this domain points to /Sites
In this /Sites directory is all my content (several Wikis) and also the phpmyadmin.
What is the issue now?
I want this xyzwiki.org not only as the hostname but as a virtual host as well.
So I have the following entry in the corresponding conf file.
<VirtualHost *:80>
ServerName xyzwiki.org
ServerAdmin [email protected]
DocumentRoot "/Sites/xyzwiki/xyzenwiki"
DirectoryIndex index.html index.php
How can I handle this?
xyzwiki.org shows the content of /Sites/xyzwiki/xyzenwiki but I cannot e.g. get access to http://xyzwiki.org/phpmyadmin
Any ideas?
Thanks
Tristan

I guess I have talk more about this issue that people got the chance to help
xyz.org is the host name of our server.
The intention of this server is to run a wiki via mediawiki.
When we first set up the server we planned to have three language versions and the corresponding wikis were found on the server under
en.xyz.org for the English version
de.xyz.org for the German and
es.xyz.org for the Spanish version
But then we decided ONLY to concentrate on the English version and so prefix en became deprecated and we only want the domain xyz.org that shows the English Wiki.
The English wiki is on our server under /Sites/xyz-wiki/xyz-enwiki
In the Server.app I defined /Sites as the server website and I have a virtual host for xyz.org AS WELL that defines /Sites/tangowiki/tangoenwiki.
This seems to overrule the entry in the server.app as xyz.org shows the content of /Sites/xyz-wiki/xyz-enwiki
As I have other "services" as well under /Sites, e.g. phpmyadmin it is not possible for me with xyz.org/phpmyadmin to get to this service.
So what I am looking for is a trick that I can keep the /Sites directory as the main directory for xyz.org. I was thinking of a symlink for the index.php from /Sites/xyz-wiki/xyz-enwiki and to remove the virtual host entry but this does not work. Any other ideas.
Cheers
Tristan

Assigning a host name in the router

Similar Messages

Maybe you are looking for