Assistance needed on Cpu O.C and Ram Timings

Hello everyone and thank you for taking time to read this i need some assistance, I would like to know exactly how to find the best cpu o.c and how and whats the best timing for my rams the specs are
Msi 880GM-E43
Amd phenom X2 545 3.0ghz Callisto (unable to unlock 2 cores *non B.E)
2x4GB Xms3 ddr3 1600 mhz (oc) 9-9-9-24 1.65v
500w psu
2x320GB Hitachi deskstar (Raid 0) W7 U64
using onboard vid atm
Thank you in advance

I have tryed to set the ratio at 1:4 to run the rams at 1600 xmp but when i do that i can only overcloak the cpu from 3.0ghz to 3.10 with the multiplier set at x15, also if i was to set the ratio to 3:10 I am able to oc to 3.6 ghz making them 1600mhz but its unstable so i feel 3.5 oc is good enough but i think the timings 9-9-9-24 could be trimmed down
so comes back to my question can it be done and if so how or what would you recomend, 1 last thing its a dual core atm
ive heard that this cpu could unlock but i havnt been successful would anyone happen to know a method on how to verify the 2 hidden cores fail i will be upgrading this chip to a 1100t or a 1055t nut if the cores unlock ill leave as is

Similar Messages

10.5.3 update: Finder pegs CPU at 100% and RAM at almost 100%

Ever since my update to 10.5.3 Finder goes nuts causing the CPU to max out and RAM usage to nearly max out, sometimes for hours at a time. I have searched high and low on the discussion boards and there is some chat but no fixes for my situation. This happens right after login with no apps other than background apps running. This never happened with Tiger and only happened for very short periods of time with Leopard prior to the 10.5.3 update. Disabling Finder is an option but its like cutting your arm off because it hurts for a few hours a day and no doctor can cure it. Not a good option.

Have you tried reinstalling using the [10.5.3 combo update|http://support.apple.com/kb/index?page=search&src=support_site.home&q=10 .5.3%20combo%20updater]?
Sometimes doing this will cure anomalies. You might also want to reset your SMU by shutting the computer down, pulling all the peripherals off and then disconnecting the power cord. Wait 15 seconds, reconnect the cord, then turn the computer on again.
Please post back with results,

Suggestions needed on cpu size/speed and memory req's for ilife/gar. band

as is noted, I've got an older ibook/processor, w/limited RAM. Suggestions on updates to present ibook g4 vs. purchase of new mac of same size?
What have other OS X 10.39 users found helpful to speed up/free up space. I keep getting the message that i can't play a certain track(s) because of space/speed needs. any help you can give is appreciated

Quote
Originally posted by blue_heart
the programs which going to run are mainly microsoft office programs,OE, IE, photshop.
In this case, I cant strongly enough recommend LOTS of ram; you wont need a fast hard drive if you can hold the whole high-res image in core I would also suggest you consider a trinatron monitor at 18" or so; so you can have purty 1600x1200 images (except for the dead line which trinatrons have) to play with; might make keeping cost under control difficult, but they *are* the only eyes you have got
Your point about real time virus scanning and loading large files (later) is well taken; in light of this I cant fault your choice of hard drive (although there is a 72GB version available at the same speed, not cheap tho.).
Quote
IMO, dropping $30 from the graphic card and $40 from hard disk will not save that much to get critical component or get higher one, if i do so i can add $30 to get another stick of 512 ram, but i rather keep the HD and GC, and for now the capacity is not an issue for me
Life in the US is good if such components are cheap; over here is Aus the high end graphics and disks are still BLOODY expensive whilst ram is relatively cheap.
Indeed, going from the drive and gfx card you have to a 80gb ata-4 and a more basic gfx card would save ~250 AUD; which is another stick of 512MB PC3700.
Lucky you.
Anyway, in light of your comments, I cant strongly enough recommend RAM; but your other components seem good (I tend toward HP printers down here, but that relates to print reliability at high ambient temp and ink costs); Dont forget a GOOD PSU (many discussions about such, I recommend Antec TruPower 480W).
Of course, I cant resist recommending you go linux, openoffice and GIMP (photoshop workalike); that would save you a LARGE chunk of cash to spend on better hardware (about ~$1200 bucks if you planned to buy XPpro, OfficeXP and Photoshop down here).
err!
jak.

Will OS X leverage Intel Turbo Boost technology when I need more CPU power?

[Mac Air 2012 middle, 11", Core i7 2.0 GHz]
Will OS X leverage Turbo Boost technology when I need more CPU power? And how could I know it?

yes and you can't control it.

Where to see CPU and RAM usage in IPAD 1

Hi:-)
While i have Apps running , I would like to be able to see CPU and RAM in use..and ideas how/where?
Thanks

There are several apps in the app store that can show you cpu and ram usage of your device, e.g. "system info"

Measuring the cpu and ram consumption of a given query in sql server

hello there how you doing and am new to this sql server forum and i suddenly popped to ask questions related to sql server
and my question goes like this
in sql server i have table called testt and it have more thna10000000 records
and i have written a query select * from testt limit 9000000; and what i want is to measure the
CPU consumption of this given query=???????????????
and
RAM consumption of this given query=???????????????
Time consumption of this given query=?????????????? this i will get it from the result bar but i don't know whether it is correct or not
any help on this it may be query, tool or configurations all are acceptable and appreciated
10Q for letting me ask questions and feeling freely.

Please check these queries and this may helps you to get whats happening on with CPU currently..
SELECT getdate() as "RunTime", st.text, qp.query_plan, a.* FROM sys.dm_exec_requests a CROSS APPLY sys.dm_exec_sql_text(a.sql_handle) as st CROSS APPLY sys.dm_exec_query_plan(a.plan_handle) as qp order by CPU_time desc
Top 50 CPU usage :
SELECT TOP 50 st.text
               ,st.dbid
               ,st.objectid
               ,qs.total_worker_time
               ,qs.last_worker_time
               ,qp.query_plan
FROM sys.dm_exec_query_stats qs
CROSS APPLY sys.dm_exec_sql_text(qs.sql_handle) st
CROSS APPLY sys.dm_exec_query_plan(qs.plan_handle) qp
ORDER BY qs.total_worker_time DESC
SP_Whoisactive --- download from : http://www.brentozar.com/responder/log-sp_whoisactive-to-a-table/
Activity Monitor and sp_who2 active also will give some idea...
Reference links...
http://channel9.msdn.com/posts/SQL-server-High-CPU--Part-1
http://channel9.msdn.com/posts/Troubleshooting-SQL-server-High-CPU--Part-2
http://jeffstevenson.karamazovgroup.com/2008/09/identifying-high-cpu-sql-processes.html
http://searchsqlserver.techtarget.com/tutorial/Step-1-CPU-usage
================
Execute this script and and start doing your analysis in your server so that you will get more idea how its working and all the details...
Sample CPU Test : Dont try this in production and try this in your test or Dev server..
-- Query to Keep CPU Busy for 2 0 Seconds
DECLARE    @T DATETIME, @F BIGINT;
SET @T = GETDATE();
WHILE DATEADD(SECOND,20,@T)>GETDATE()
SET    @F=POWER(2,30);
You can easily change the parameter in the DATEADD and can make it run for 50 seconds.
-- Query to Keep CPU Busy for 50 Seconds
DECLARE    @T DATETIME, @F BIGINT;
SET @T = GETDATE();
WHILE DATEADD(SECOND,50,@T)>GETDATE()
SET    @F=POWER(2,30);
Raju Rasagounder MSSQL DBA

Assistance needed with new monitor and printing from LR3

I just purchased a new IPS monitor. I have calibrated it using the HP Display assistant that came with it. It is an HP ZR 22w. I saved my calibration as a preset - however - this is not appearing as a profile when I try to select it in the print module. the checkbox for "include display profiles" is ticked. If I allow the printer to manage - the pictures are much warmer than on the IPS display. My printer is a canon mg6120 and I am running windows 7. I would appreciate any assistance that anyone can provide. Thank you

I think the "HP Display assistant" is a software tool, is that right?
Ideally with Lightroom, you should use a hardware calibration/profiling tool (Spyder, Eye One, Color Munki etc). In particular, you need a monitor profile that contains colour space information. I had a look through the HP Display Assistant user manual, and it appears the software does calibration but it probably doesn't put colour space info in the profile. It'll be better than nothing, but a hardware tool is better.
However:
I saved my calibration as a preset - however - this is not appearing as a profile when I try to select it in the print module. the checkbox for "include display profiles" is ticked. If I allow the printer to manage - the pictures are much warmer than on the IPS display. My printer is a canon mg6120 and I am running windows 7
This is not what you want to do! The profile that the HP Display Assistant creates is for the monitor, and only for the monitor. It gets the right white point and tone curve for the monitor. What you need in the profile drop-down in LR print module is a printer profile, not a monitor profile (except on very special circumstances).
I'm not familiar with the MG6120, but when I googled "profiles for canon mg6120" I got a lot of hits, so I assume profiles are available. It's quite likely that some came with the printer driver, and were installed with the printer software. When you select "profile" in LR print module (you may well have to go to "Other..." to see them all) then there should be profiles for the printer - possible lots of them - one or more for each paper type. If they're not there, see the Canon documentation (or google it) to find out how to load them.
If you can't find any profiles for the printer, then try using sRGB (or probably it's "sRGB IEC..."). Without colour management, your printer will probably expect sRGB images, so this should be roughly right, but a specific profile for the printer is better. This is one of those very special circumstances when something other than a printer profile (and sRGB isn't a printer profile) may be better than nothing.

I have a PowerPC G4, 1.5 Ghz, with 1.5 GB of ram. Currently running OSX 10.4.11. Can I upgrade to 10.5.8 (or higher)? Need to load new software and said that was the minumum requirement.

I have a PowerPC G4, 1.5 Ghz, with 1.5 GB of ram.
Currently running OSX 10.4.11.
Question: Can I upgrade to 10.5.8 (or higher)? Need to load new software and said that was the minumum requirement was 10.5.8
Thanks, WPC-2012

Mac OS X 10.5 Leopard installation system requirements
http://support.apple.com/kb/TA24950
Leopard is no longer available at the Apple Store but may be available by calling Apple Phone Sales @ 1-800-MY-APPLE (1-800-692-7753).
If you can't obtain a retail install DVD from Apple, look on eBay or Google the installer part numbers to possibly find at an on-line store. Here's what to look for:
MB427Z/A Leopard 10.5.1 install DVD
MB576Z/A Leopard 10.5.4 install DVD
MB021Z/A Leopard 10.5.6 install DVD (single user)
MB022Z/A Leopard 10.5.6 install DVD (5-user family pack)
Installing Mac OS X 10.5 Leopard
http://support.apple.com/kb/HT1544
Mac OS X 10.5 Leopard Installation and Setup Guide
http://manuals.info.apple.com/en/leopard_install-setup.pdf
After you install the base 10.5, download & install the 10.5.8 combo update at http://support.apple.com/downloads/Mac_OS_X_10_5_8_Combo_Update
The DVD should look like this
Caution - Leopard does not support classic mode. So, if you currently open OS 9 apps in classic mode, you won't be able to do this if you upgrade to Leopard.
 Cheers, Tom

How much storage and ram does a Mac need?

I'm thinking about buying a Macbook Air as a present for my Mum, however I've always used Windows and have no clue at how OSX works. For example I know that Windows requires 8GB of ram and 500GB of storage at least for it to run well and be future proofed for the next couple years. I'm guess OSX uses less resources since all the models seem to be really low on storage and ram, the models with more are way more expensive but you cannot add more later which *****. So I'm just wondering how much does a modern Mac need these days?
Just an extra question...
I'm mainly making this purchasing decision on battery life, every Windows Laptop I've come across seems to only last about 3 hours. Will OSX be able to do everything Windows generally does? My Mum isn't a heavy user with specific needs but she uses Microsoft Office a lot and her work requires for her to have Flash Player in the browser and I know IOS doesn't support that, does OSX?
Thanx.

How much she need depends on what she wants to do with it. I am perfectly happy with my mid-2012 Air with 4/128. The storage issue might be most easily answered by seeing how much space she has filled on her current computer.
You can install Flash Player with OS X.

Z77A-gd65A boot error code 15 rebthing i removed all except cpu and ram and oot

my pc used to work fine yesterday i shut it down and started it today and it kept cycling rebooting at code 15 on debug i changed to bios B and the same thing did clear cmos both ways even removed the battery the same also removed all except cpu and ram but still the same result please help !

I have no idea how you possibly could corrupt bios A if you weren't running Live Update or manually attempted to flash. if bios is really corrupted follow: >>Flashing a Corrupted bios when the alternate bios still works<<

Is it necessary to manually set cpu and ram specs in bios anymore?

I just ugpraded with a K8N Neo2-F board, and Venice 3500+ cpu. I didn't do anything in particular with the cpu/ram spec settings in the bios. CPU-Z recognizes the cpu as a venice core 3500+, using multiplier 11 and fsb clock 200mhz, and the ram is recognized as 1GB pc2700, with assorted clock settings. The ram is from Crucial and was spec'd out to my old MSI KT4AVL board, so I looked the same ram up again at Crucial.com, but it didn't list the various clock settings anywhere in the specs on that particular chip online. At least the CAS Latency is showing up correctly in CPU-Z, from what the label on the ram says. Should I just assume the other clock settings are correct, too? How can I find out what they should be for my ram? (I know - I should probably be using Corsair DDR400's like everyone else here, but $ is tight so I just reused what I had...)

RAM timings should be set up if you want the best performance. Alot of times the motherboard is able to determine this but not always. In CPU-Z there are two tabs related to memory. One is SPD which should show you the recommended timings for your memory, the other tab Memory should show you what your memory is currently running out. If they are different I would go with what is listed on the SPD tab and put those values in the bios.
It would definitely be beneficial to upgrade your memory to 2 PC-3200 matched sticks, so you get the speed increase from the increased memory bandwidth and also so you can get dual-channel. I would put memory as the top priorty for the next item to get for the computer.
Good Luck
Jeremy

CPU and RAM size for database

How can we see what is the CPU and RAM size for the database?
<div class="jive-quote">select * from v$version</div>
BANNER
Oracle Database 10g Enterprise Edition Release 10.2.0.5.0 - 64bi
PL/SQL Release 10.2.0.5.0 - Production
CORE     10.2.0.5.0     Production
TNS for HPUX: Version 10.2.0.5.0 - Production
NLSRTL Version 10.2.0.5.0 - Production

cat /proc/meminfo
root:     total:      used:      free:           shared:     buffers:     cached:
Mem:      1055760384     1041887232     13873152     0     100417536      711233536
Swap:      1077501952      8540160      1068961792
MemTotal:          1031016 kB
MemFree:          13548 kB
MemShared:          0 kB
Buffers:          98064 kB
Cached:               692320 kB
SwapCached:          2244 kB
Active:               563112 kB
Inact_dirty:          309584 kB
Inact_clean:          79508 kB
Inact_target:          190440 kB
HighTotal:          130992 kB
HighFree:          1876 kB
LowTotal:          900024 kB
LowFree:          11672 kB
SwapTotal:          1052248 kB
SwapFree:          1043908 kB
Committed_AS:          332340 kB
cat /proc/cpuinfo
processor : 0
vendor_id : AuthenticAMD
cpu family : 15
model : 31
model name : AMD Athlon(tm) 64 Processor 3000+
stepping : 0
cpu MHz : 994.927
cache size : 512 KB
fpu : yes
fpu_exception : yes
cpuid level : 1
wp : yes
flags : fpu vme de pse tsc msr pae mce (snipped)
bogomips : 1956.97
TLB size : 1024 4K pages
clflush size : 64
cache_alignment : 64
address sizes : 40 bits physical, 48 bits virtual
power management: ts fid vid ttp

MOVED: getting most ffrom my cpu and ram cinfigd in the bios

This topic has been moved to Overclockers & Modding Corner.
getting most ffrom my cpu and ram cinfigd in the bios

You can use CPU-Z to check your settings. I find it best to just use good ole bios overclocking. Set ram 1:1(FSB/Dram ratio) and FSB to 200 that that should give you 2200Mhz.

Need help with Windows Migration Assistant, as a window pops up and I don't know what to do?

Hiya, so I just purchased a macbook pro and I want to transfer files using Windows Migration assistant.
However whenever I go to do it, the mac connects to the computer and the computer always stays on 'trying to connect to mac'
and sometimes this windows pops up where it says:
'Email
There is no email program associated to perform the requested action. Please install an email program, or, if one is already installed, create an association in the Default Programs control panel.'
I'm confused as I have an email program on the pc ( Windows Live Mail)
However I don't know what it means to create an 'association' and I have gone into default programs control panel to try find this associations and have however I don't know how to make this association as I've searched for the program Windows Migration Assistant, however it isn't there and I'm not sure what to do.
Please help?

OS X 10.9 Mavericks/ 10.10 Yosemite
1. Repair Disk http://support.apple.com/kb/PH5836
2. Reset PRAM: http://support.apple.com/kb/PH14222
Best.

Some improvement to hot plg CPUs and RAM in Solaris 11?

Hi,
We plan to use Solaris 11 in VMWare environment. As all of you know, you can add CPUs and RAM on the fly depending on the guest operating system. A lot of Windows versions can handle that, and some Linux (64bits based) distros as well.
That's not possible in Solaris (at least in Solaris 9 and 10): http://vmwarethiru.blogspot.com/2011/04/vsphere-support-for-memory-hot-add-and.html
Is there some improvement on this? I mean... it will be possible to add CPU and RAM from the VMWare hypervisor when you're using Solaris 11 as a guest?
I seems a virtual provider (VMWare in this case) issue, but it's not: it depends on the guest operating system capabilities.

Really good news!
In Linux kernel, the module need is called acpi_hotpug, so I suppose that internally they´re using as well the ACPI events.
As you said, another thing will be if the VMWare guys will take profit of this new feature.
Can you point me out some documentation about?
Thanks.

Assistance needed on Cpu O.C and Ram Timings

Similar Messages

Maybe you are looking for