Assistance to solve this problem

 Hi,
Event filter with query "select" form HP_TempSensorFailureEvent " could not be (re) activated in namespace"//./root/WMI"because of error 0x80041010. Events may not be delivered through this filter until the problems is corrected.

Hello,
Suggest you to post this question in Scripting forum to get better assistance... This is Exchange server forum...
http://social.technet.microsoft.com/Forums/scriptcenter/en-US/home
Blog |
Get Your Exchange Powershell Tip of the Day from here

Similar Messages

  • One of the usb devices attached to this computer has malfunctioned, and Windows does not recognize it. For assistance in solving this problem, click this message.

    I connected my sons Ipod Touch to my pc and it worked fine. Now, when I try to connect my iPad the following message comes up: One of the usb devices attached to this computer has malfunctioned, and Windows does not recognize it. For assistance in solving this problem, click this message.
    I checked the cable. It surely is not the cable. If I connect the iPod again it works fine. If I use the same cable with my pc and ipad at work or my other son’s laptop, it is working perfectly. It is only on my laptop where the iPod was connected. Something tells me it got something to do with the drivers that went corrupt or something when I connected the iPod.
    I searched the internet and I see a lot of people gets this message. Still no solved answers yet. Is there a place where I can download the drivers again or any other suggestions?
    Windows 7 and iPad 2
    Kind regards,

    I was hoping it would be something like a USB device conflict, but now the shuffle is the only thing connected...
    This article was one of the ones you linked to above in your initial post
    http://support.apple.com/kb/TS1369
    Under Part 9. Verify that USB drivers are installed, did you try the steps in If only "Unknown Device" appears?  That appears to be your situation.
    Also, you said that the shuffle initially worked well enough to do a sync, then it had the same problem again.  If you can get it to work again initially, before doing anything else, try the following.  Select the shuffle in the iTunes sidebar, under DEVICES.  Over to the right, go to the Summary tab.  By default, the checkbox for Enable disk use should be unchecked.  If so, check it and Apply the change.  See if that makes any difference. 
    (If Enable disk use was already checked, try unchecking it and Apply the change.  Basically, set it the "other way" and see if there is any improvement.)
    NOTE:  When disk use is enabled, you have to eject the iPod in iTunes before disconnecting it physically.
    If the disk use change makes a difference, that may provide a clue about the actual cause.

  • Using iPod shuffle 4th generation for first time and receiving the error : one of the USB devices attached to this computer has malfunctioned, and windows does not recognize it. For assistance in solving this problem, click this message

    Using iPod shuffle 4th generation for first time and receiving the error : one of the USB devices attached to this computer has malfunctioned, and windows does not recognize it. For assistance in solving this problem, click this message.
    Using win 7 and latest iTunes [10.6.3]. Have already gone through below links and did not find any solution.
    http://support.apple.com/kb/HT2292
    http://support.apple.com/kb/TS1369
    http://support.apple.com/kb/HT1923
    http://en.kioskea.net/forum/affich-17997-ipod-not-detected

    I was hoping it would be something like a USB device conflict, but now the shuffle is the only thing connected...
    This article was one of the ones you linked to above in your initial post
    http://support.apple.com/kb/TS1369
    Under Part 9. Verify that USB drivers are installed, did you try the steps in If only "Unknown Device" appears?  That appears to be your situation.
    Also, you said that the shuffle initially worked well enough to do a sync, then it had the same problem again.  If you can get it to work again initially, before doing anything else, try the following.  Select the shuffle in the iTunes sidebar, under DEVICES.  Over to the right, go to the Summary tab.  By default, the checkbox for Enable disk use should be unchecked.  If so, check it and Apply the change.  See if that makes any difference. 
    (If Enable disk use was already checked, try unchecking it and Apply the change.  Basically, set it the "other way" and see if there is any improvement.)
    NOTE:  When disk use is enabled, you have to eject the iPod in iTunes before disconnecting it physically.
    If the disk use change makes a difference, that may provide a clue about the actual cause.

  • Hi, my name is Amit, my hot corners stop working after some time. Have to go to mission control to reset them, however they stop again after some time. This is annoying. Can someone please assist to solve this problem? Thanks Amit.

    Hi my name is Amit, after upgrading to OS X Maverick I often have problem of my Hot corners stop working after a short period of time. I have to go to mission control and have to reset them for them to start working again. However this is temparory and they stop working again and this is quite annoying. Can someone suggest a cure to this problem please. I will be grateful. Thanks Amit.

    Back up all data.
    Triple-click anywhere in the line below on this page to select it:
    ~/Library/Preferences/com.apple.dock.plist
    Right-click or control-click the line and select
    Services ▹ Reveal in Finder (or just Reveal)
    from the contextual menu.* A folder should open with an item selected. Move the selected item to the Desktop, leaving the window open. Log out or restart the computer and test. If there's no change, put the item you moved back where it was, overwriting the one that may have been created in its place. Log out again. Otherwise, delete the item you moved.
    *If you don't see the contextual menu item, copy the selected text to the Clipboard by pressing the key combination  command-C. In the Finder, select
    Go ▹ Go to Folder...
    from the menu bar and paste into the box that opens by pressing command-V. You won't see what you pasted because a line break is included. Press return.

  • Iphone 4 is hiting in ios 5.1.1. any one know how to solve this problem??

    iphone 4 is hiting in ios 5.1.1. any one know how to solve this problem??

    This sounds like a hardware problem and should be taken to Apple if the heating / "hiting" becomes disturbing to you. If you feel that your iPhone has a heating / "hiting" problem and needs to be repaired, please contact Apple Support and they can further assist you in having it inspected, repaired, or even replaced. In the past, the overheating of Apple products has been known to cause harmful problems to a few particular users. Please evaluate your situation and take further action if you feel necessary.
    http://www.apple.com/support/contact/

  • Please solve this problem for me.

    I can not get it up in the game's "Your Purchase Could Not Be Completed. For assistance, contact iTunes Support at www.apple.com / support / itunes / ww. Please solve this problem for me.

    Maybe you should try following the directions in the message... http://www.apple.com/support/itunes/ww

  • We have 'CS6' version of Adobe. We are facing a problem with 'Acrobat Pro'. Every month that is stop working and everytime need to install. Kindly help us regarding solving this problem...

    We have 'CS6' version of Adobe. We are facing a problem with 'Acrobat Pro'. Every month that is stop working and everytime need to install. Kindly help us regarding solving this problem...

    Your Acrobat is running in Trial Mode.  Try this KB: Creative Cloud applications unexpectedly revert to trial mode | CS6, CCM
    If it doesn't work you need to contact Adobe Support for assistance.

  • HT4009 I can't make in app purchases on clash of clans every time I try it tells me to come here. This is really annoying! So how do I solve this problem?

    I can't make in app purchases on clash of clans every time I try it tells me to come here. This is really annoying! So how do I solve this problem?

    I understand it is from the App Store. That is part of iTunes. You still need to contact them for assistance, or you can try Express Lane, https://expresslane.apple.com/GetproductgroupList.action

  • I have been trying to update to iOS 5 and every time I hit update it says, " There was a problem downloading the software for the iPhone. The network connection could not be established."  What do I need to do to update to solve this problem?

    I have been trying to update my iPhone 4 with iOS 5 for about 30 minutes and I keep getting the same thing. It says,"There was a problem downloading the software for the iPhone. The network connection could not be established." What do I need to do to solve this problem?

    iOS: Resolving update and restore alert messages
    For error -50: See error 13 and 14: 
    Error 13 and 14: These errors are typically resolved by performing one or more of the steps listed below:
    Perform USB isolation troubleshooting, including trying a different USB port directly on the computer. See the advanced steps below for USB troubleshooting.
    Put a USB 2.0 hub between the device and the computer.
    Try a different USB 30-pin dock-connector cable.
    Eliminate third-party security software conflicts.
    There may be third-party software installed that modifies your default packet size in Windows by inserting one or more TcpWindowSize entries into your registry. Your default packet size being set incorrectly can cause this error. Contact the manufacturer of the software that installed the packet-size modification for assistance. Or, follow this article by Microsoft: How to reset Internet Protocol (TCP/IP) to reset the packet size back to the default for Windows.
    Connect your computer directly to your Internet source, bypassing any routers, hubs, or switches. You may need to restart your computer and modem to get online.
    Try to restore from another known-good computer and network.

  • When i login to update my existing apps, the login window shows the wrong apple id. and it's all prayed out, i can't change it. how do i solve this problem?

    When I login to update my existing apps, the login window shows the wrong apple id. i cannot change it because it is all grayed out. how do i solve this problem?

    Content and Apple IDs -
    Content is forever tied to the Apple ID that bought it. Apple does not transfer content from one Apple ID to another. Apple does not merge Apple IDs. You will never be able to access your content bought with one Apple ID with a new Apple ID.

  • After updating to Firefox 7.0.1, menu bar for Google,yahoo, Facebook (message,notification,profile,home) and others site are disabled. How can solve this problem?

    after updating to Firefox 7.0.1, menu bar for Google(web ,image,video,map etc),yahoo, Facebook (message,notification,profile,home) and others site are disabled. even I cant log out from different sites cz the log out bar is completely disabled. I tried with Firefox 4;5 and 6, same problem exist . I tried by active all add ons for facebook, same problem exist. If I use internet explorer , I don't find such problem with it.
    How can I solve this problem?

    Thanks a lot for your swift response. And sorry if it was a bit too hectic to go through my detailed query (which I did because it was misunderstood when I asked previously). As I've mentioned above, I was informed that updating to 5.0.1 would '''require''' me to '''delete''' the current version and then install the new one. And doing so will involve losing all my bookmarks. I guess I should have been more specific and detailed there. By losing, I didn't mean losing them forever. I'm aware that they're secured in some place and deleting and installing the software doesn't harm its existence. What I meant that if I install the new version, I'd have to delete the old one. And after installing the new version, I'd have to transfer them (bookmarks) back from wherever they are. Get it? When it updated from 3.6.9 to 3.6.13, and from 3.6.13 to 3.6.18, I didn't need to follow that process. They were already present on their own.
    BTW, I'm having no problems with 3.6.18 but after learning about the existence of version 5.0.1, I'm a bit too eager to lay my hands over it.
    Thanks for your help; hope this wasn't extremely long.

  • I recieve SMS and i hear established melody and I do't hear the person on all over SMS. How to solve this problem?

    Problem with an incoming message. For example, during my conversation the second line receives a call, I hear the sound in dynamics such as "piiiip piiiip," but when in this situation I recieve SMS and i hear established melody and I do't hear the person on all over SMS. How to solve this problem? Perhaps someone tell me? save in advance

    Not Charge
    - See:     
    iPod touch: Hardware troubleshooting
    iPhone and iPod touch: Charging the battery
    - Try another cable. The cable for 5G iPod (lightning connector) seems to be more prone to failure than the older cable.
    - Try another charging source
    - Inspect the dock connector on the iPod for bent or missing contacts, foreign material, corroded contacts, broken, missing or cracked plastic.
    - Make an appointment at the Genius Bar of an Apple store.
      Apple Retail Store - Genius Bar

  • How I can solve this problem or manipulate it ports 80,443 are closed by ISP and they don't want to open it

    hi,
     I see that I have a particulier abonnee of my ISP , which has closed all the ports for security reason and they don't want to open  any of it 80,443 ect.
    suppose If I want to use Essential server 2012  how I can solve this problem , essential wants domain name whith A record.
    I asked DDNS service provider if I lease from them a domain name whith A record  would that help to open or manipulate the port 80,443  they said that I have to solve this problem myself . they lease only domain names with dynamic dns records.  
     so what can be a solution the ISP provider won't open this ports , how I can solve this problem .   domain name with ip adres is not helping so what it's go to help?
    thanks
    johan
    h.david

    The domain name in this instance is only used for remote access, and is seperate from the active directory domain name.
    If your ISP blocks port 80 and 443, and you dont intend to use remote access anyway, the wizard will likely not complete successfully whether you have a valid domain name or not.
    Robert Pearman SBS MVP
    itauthority.co.uk |
    Title(Required)
    Facebook |
    Twitter |
    Linked in |
    Google+

  • Hello all .. i have a big problem in my ipad version 5.1.1 that is when i connect the ipad with my computer the i tunes give me this message ( itunes couldnt connect to this ipad .an unknown error occurred (0xE8000012).) how i can solve this problem pleas

    hello all .. i have a big problem in my ipad version 5.1.1 that is when i connect the ipad with my computer the i tunes give me this message ( itunes couldnt connect to this ipad .an unknown error occurred (0xE8000012).) how i can solve this problem please
    and this is an pic for the problem

    There is some troubleshooting for 0xE8 error codes on this page : http://support.apple.com/kb/TS3221 - you could see if anything on that page fixes it

  • See who can solve this problem

    Parameter name   || Typing     ||  Associated Type
    ACGL_ITEM         || Structure ||  ACGL_ITEM
    this give error ( Typing is only for Like,Type,Type Ref To )
    therefore i change it to Type
    but it telling me that the ( TABLES parameters are obsolete!)
    guys what can i do, is there a solution to solve this problem??
    Thank you.
    Edited by: guanwei su on Mar 10, 2008 7:05 AM

    The following code might be helpful:
    TYPES: types_t_acgl_item TYPE STANDARD TABLE OF acgl_item.
    DATA: gt_acgl_item TYPE types_t_acgl_item.
    PERFORM sub_perform USING gt_acgl_item.
    *&      Form  SUB_PERFORM
    *       text
    *      -->UT_ACGL_ITEM  test Table
    FORM sub_perform USING ut_acgl_item TYPE types_t_acgl_item.
    ENDFORM.                    " SUB_PERFORM
    Hope That Helps
    Anirban M.

Maybe you are looking for

  • Has anybody experienced the iPhone off switch not working all the time.

    I have an iPhone 5, it's about 16 months old and it has experienced an annoying issue.  The off button does not work all the time, sometimes I have to press it multiple times and other times it just works.  The worst case is when it does not work at

  • Problem when another user update record.

    Hi All, i am using jdev 11.1.1.5.0 use case: i have create one adf table which is based on vo where a column claimed_by. i have add a where clause in vo where claimed_by is null. default value of claimed_by is null. when user claimed particular recor

  • No material is transferred in storage location after confirmation in COR6N.

    Dear Master, When I confirm in cor6n there is movement of goods & confirmation takes place.But there is no transfer of material in storage location & even when the order is checked the delivered QTY is zero.Since my process has 3 confirmation ( i.e 2

  • Modiying Transport requests

    Hi, If we have made some changes and have the objects assigned to a transport request, if we need to remove some objects from the request (before releasing it or during development), how can we do so? This could be in situations where we have added a

  • HT201269 Don't want to lose content on new iPhone when restoring from old iPhone

    If I follow the steps described in http://support.apple.com/kb/HT2109 will I lose the contacts, apps, photos and videos that are already set up on my new iPhone?