ASUS Sonicmaster X102BA Win764bit - usb bugcode driver blue screen on sleep

Hello
I recently downgraded to windows 64 bit and when the PC goes to sleep it comes back up, freezes for about 15 seconds and then reboots with the BSOD error. I noticed in device manage its missing 2 drivers (SM Bus Controller and Universal Serial Bus (USB)
Controller) and I cannot seem to find them anywhere can some help please?
Thanks.

This link sorted my problem
http://support.amd.com/en-us/download/chipset?os=Windows+8+-+64 - AMD Chipset Drivers
if that does not solve it maybe this link might http://www.asus.com/supportonly/X102BA/HelpDesk_Download/

Similar Messages

Win7 can't boot in USB hard drive blue screen 7b error,but can boot when use PD8

Install Win7 64bit in a USB hard drive through some tools,when start windows the microsoft logo appear,get blue screen.
***stop:0x0000007B(0x80786B58,0xC0000034,0x00000000,0x00000000)
problem has been detected and windows has been shut down to prevent damage to your computer.If this is the first you've seen this stop error screen restart your computer .If this screen appears again.follow these steps:Check for viruses on your computer.Remove any newly hard drives or hard drive controllers.Check your hard drive to make sure it is properly.Configured and terminated.Run DCHKDSK/F to check for hard drive corrption,and then restart your computer.
Technical:
***stop:0x0000007B(0x80786B58,0xC0000034,0x00000000,0x00000000)
But when use Parallels Desktop 8 My boot camp ,the win7 can boot normally.
Any solution?
Thank you.

Hi,
If this issue is related with firmare, then it's recommend to contact the vender\manufacture, if you got any update of this issue, we'd be appreciate that you could share your experience with us.
Regards
Yolanda Zhu
TechNet Community Support

Vista SP2 BUGCode error blue screen dump

I haven't had a days problem with my PC for almost 2 years. Keep up with updates routinely. Installed SP2 and now get blue screen dumps.
Been working with Microsoft for a week. Have isolated a USB Generic HUB driver if disabled I do not dump. Driver appears to be related to internal fingerprint reader that uses digital persona sw.
tried updating the driver an no good. Any ideas?
Apparently there is an issue with HP's and this upgrade on PC using Nvidia controllers. Suppose to have an unpublished hotfix but the file was empty.
Since it is related to Digital Persona (i think) microsoft won't be able to help anymore.
JP5

Benn working with Microsoft support for free they have put in over 20 hours on this. We have traced ti to the finger print reader from authen Tec and my HP all in one C7280. If the reader is enabled and you plug in the printer it will crash within 20". If I disable the reader I can plug in the printer,
Prior to SP2 it ran fine. Microsoft is reluctant to remove SP2 and I am not happy with HP as their software updater is te one that told me to install it and they want to charge for telephone support even though it is apparant it is a driver from their 3rd party software. they said to update bios which I did and it did nothing.
JP5

White screen, new hard drive, blue screen. Help!

Tried to boot my MacBook Pro (2011) and just had blank white screen. Tried to boot from Mountain Lion bootable flash drive and just get a blue screen.
Installed new hard drive. Same thing. Suggestions?

After the dealer looked it over, he determined it has a bad logic board. However, searching online, I see the cause of all these 2011 MBP failures is due to the Raedon graphics card in them. Apple was replacing free for iMacs with the same part, but so far isn't doing the same for MacBook Pro's. I have emailed Apple, intend to call them, and posted on their support forum as well as other ones. FRUSTRATING.

Issue with USB ports and Blue Screen

So, I had to send my Satellite L355-S7905 back and Toshiba had to do a factory restore. I got it back 2 weeks ago and now I have a new problem; 2-3 times a day my mouse and printer stops working, these are connected via USB ports and I get a message that the device is no longer recognized. I found a solution on the Microsoft site to go to Device manager and Scan for new hardware changes and then Restart. I do this and when I restart I get the dreaded blue screen. So I then have to unplug, take out the battery and turn the computer back on. Then the mouse and printer are recognized. This will work for several hours and then the whole thing happens again. So, are there any long term solutions? Can anyone tell my why this is happening? Please note, that that the printer and mouse are not new and no new hardware has been installed since getting it back from the factory.
Thank you for your help!!
Jennifer

start-->control panel-->system and security-->device manager-->expand the universal serial bus controllers-->right click and uninstall all of the USB root hubs-->restart-->they will reinstall on restart, and search for attached hardware.

New Battery + New Hard Drive = Blue Screen of Death.

The series of events:
1. Powerbook acts slow, but nothing too frustrating. Until its starts to randomly quit when browsing the internet regardless of browser being used; however, I suffer through a few weeks with this issue.
2. Battery ceases to function one day after warranty ends, Apple Genius feels my pain but still charges for the new battery. I also inquire about the internet browsing issue and he runs some test and concludes that my airport card is failing. I choose to not replace the airport card at that time.
3. I purchase a time capsule and complete the initial backup; however, all further backups fail.
4. I purchase a macbook pro.
5. The day after purchasing the macbook pro, and before I had sufficient time to transfer all needed files from either the powerbook or the time capsule, the powerbook enters into the blue screen of death. The time capsule refuses to recognize the macbook pro as I desperately attempt to save at least a portion of my files.
6. I visit the apple store dragging a small suitcase behind me which holds the powerbook, the macbook pro, and the time capsule. My appointment began at 10:00am. At 8:00pm I left the Apple Store (the geniuses were glad to see me go, 5 of them were required to help me). Upon leaving, all files from the time capsule had been transferred to the macbook pro (at one point the genius said to me "there's a 50/50 chance this will work, if it doesn't you will lose everything" I almost cried) and the powerbook was given the definite diagnosis of a severely corrupt hard drive with the recommendation to replace it. (Sidenote: A different genius tested the airport on the powerbook and said its perfect and does not need to be replaced.)
7. Hard drive replaced in powerbook.
8. Powerbook used successfully to connect to macbook pro and watch a movie on the powerbook with the file based on the macbook pro.
9. Attempted to use powerbook again for the same task. Powerbook connected to macbook pro but wouldn't show any files. I disconnected the two and tried again, this time powerbook would not connect at all...just kept saying "connecting." Attempted to restart powerbook and was greeted with the blue screen of death.
The battery in the powerbook has barely 10 cycles. The new hard drive has nothing on it except what was loaded with leopard and firefox (there is absolutely no user-created content other than the firefox cache which only loaded the welcome page so I could confirm I was connected to the internet). I have not connected it to the time capsule.
I would really like it if the powerbook worked again. Is there a deeper problem with it since it barely worked after putting a new hard drive in? Is there any chance of hope for renewed life?

Hi
System Specs
AMD Athlon XP 2500+
Abit NF7 2.0
300 watt power supply, Generic Case
Geforce FX 5600AGP 8X 256MB
SB Audigy 2 Platinum
PCI SLot fan
Case fan
80gb master, 60gb slave Western Digital hard dri'ves
Lite on dvd-rom
Lite on CD-rW
Windows XP Home Edition Sp2
Viewsonic VX-900-2 Monitor
I think that's all you need correct. The problem occurs when i disconnect the headphones from the jack, it could be after listening to music, or it could be when there idel, really doesn't matter it seems, unplug them to go back to regular speakers, and bam reboot
please help on this..
Drivers are latest for each item.
Software is up to date as it can be.
Message Edited by bikeman on 04-20-2005 08:4 PM

DeviceNet driver blue screen

I am running LabView Prof., DNet version 1.3 on a laptop, ThinPad T20. I get blue screens after I have opened and closed polling several times. The less I open and close, the better off I am. The error says "Page Fault" basically, and the program will run fine after rebooting, and seems to be great right up until the blue screen. Please help. This is controlling poisonous gases, and I can't tolerate this.

Hi,
Our R&D department is aware of this problem. Send an email to the technical support department at www.ni.com/ask. Thanks.
DiegoF
National Instruments.

New macbook pro 17, gets blue screen after sleeping

Had it for 1 or two months and haven't had any problems. Was just using it and closed it to sleep, and reopened it and it was stuck on the blue screen.
Safe mode won't work. Resetting the PRAM won't work.
What the heck?

Hi,
A flashing question mark appears when you start your Mac
Hopefully something will get your Mac running again.
Carolyn

Why does my MacBook Pro not find USB hard drive after waking from sleep?

is this a known issue? i have to manually turn off/on the Mac's Airport to re-establish USB HD connection (or Time Machine won't find it either).

bender73 wrote:
is this a known issue? i have to manually turn off/on the Mac's Airport to re-establish USB HD connection (or Time Machine won't find it either).
I hate to have to tell you this, but backing-up that way is "iffy" and *+not supported by Apple.+* See [Using Time Machine with an Airport Extreme Air Disk|http://web.me.com/pondini/Time_Machine/Airport.html] (or use the link in *User Tips* at the top of this forum).
It sounds like you're using that disk for other things besides your backups; if so, and if you're going to continue backing-up that way, it really should be partitioned so Time Machine has it's own, exclusive space. See #Q1 in the same link.
Time Machine should find it's partition when OSX wakes up; if it doesn't, try a "full reset" of Time Machine, per #A4 in [Time Machine - Troubleshooting|http://web.me.com/pondini/Time_Machine/Troubleshooting.html] (or use the link in *User Tips* at the top of the +Time Machine+ forum).

Asus computer blue screen when injected with HP2515 printer

When the hp2515 inject into my asus computer for printing, it will appear blue screen after i am printed for few paper by injected with USB 2.0 port~~can anybody solve my problem?? I am suffered for that problem~

Hi @yiyi,
Welcome to the HP Forums!
I see that you are getting a blue screen whenever your plugin your HP Deskjet Ink Advantage 2515. I am happy to look into this for you!
I am not sure what your Operating System is, but if you are using Windows 7, I think this guide will help, Windows 7: A Windows Stop Error (Blue-Screen Error) Occurs When Plugging an HP Printer into the Comp....
Otherwise, please respond with the Operating System you are using. If you do not know the Operating System you are using, please visit this website. Whatsmyos, and if you have tried other ports on the computer.
Hope this solves your problem, and have a great day!
RnRMusicMan
I work on behalf of HP
Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
Click the “Kudos Thumbs Up" to say “Thanks” for helping!

Blue screen occurs when I connect USB hybrid TV tuner

Hi, I brought a USB Hybrid TV tuner PX1256E and I can't make it run. I have Windows Media Center and when I install the software and connect the hardware to the USB port a blue screen (windows crash) appear and my computer restart.
Please, May anyone help me?
Thanks, and sorry for bad English. ;)

I am not 100% sure but I believe there can be some conflict between installed software and Windows Media Center. I have Toshiba USB DVB-T TV tuner and it works well on my WXP Professional preinstalled notebook.
I have tested it with Vista too and it works perfectly. If possible test it on some friends PC with preinstalled WXP Home or Professional.

Blue screen hard disk dump AND memory dump

I sent my toshiba satellite a215-s4767 to the repair depot for a screen replacement and since i got it back i have had 2 blue screen memory dumps and 1 hard disk dump blue screen(that was last night). I got it back on christmas eve so ive had it back for 2 weeks.

Please take a look at this document USB 3.0 Blue Screen Document. Verify your USB 3.0 chipset is the same as described in the document and if it is the same download the fix from Intel.
Best regards,
I am an HP employee

Blue Screen After Waking up from sleep.....

So whenever I put put my screen dowm(the laptop is on) and after while i open my screen.
There are blinking black colored lights and after while a blue screen appears and says "There is a problem in the computer or installed drivers or in a update so windows is shuttig down to prevent the damage.....
Dumping files:125 (and so on)
after it reboots by itself the windows gives me message saying "There is a problem with ATI DISPLAY DRIVER"

Hi,
Please try the Microsoft fix:
http://answers.microsoft.com/en-us/windows/forum/windows_7-performance/blue-screen-after-sleep-mode/...
Good luck.
BH
**Click the KUDOS thumb up on the left to say 'Thanks'**
Make it easier for other people to find solutions by marking a Reply 'Accept as Solution' if it solves your problem.

Blue screen hard dump to disc when printer is connected

hpofficejet pro 8600 plus, windows7 64 bit, new printer, laptop hp pavillion dv7, error/ blue screen, hard dump, save to disc ,restart to recover, multiple times now, unplugged printer to avoid. Drivers and software reinstalled. Message says update bios maybe?

Please take a look at this document USB 3.0 Blue Screen Document. Verify your USB 3.0 chipset is the same as described in the document and if it is the same download the fix from Intel.
Best regards,
I am an HP employee

Deskjet 6940 causing a blue screen and rebooting PC on bootup

I have a strange problem with a clients PC. Whenever it boots up, if the Deskjet 6940 is connected via a usb cable it blue screens and reboots. The PC was recently updated to Service Pack 3, at first I thought the amount of memory was too low (248 mb, with 8 shared with video). So I upgraded the memory to 1 Gb but it still happens, if the printer is not plugged in it goes into Windows and works fine. if I then plug the printer in it reboots immediately.
I've tried different USB sockets, I've tried uninstalling the drivers and all the HP software, rebooting and downloading the latest drivers from HP. This seemed to cure it for a few hours, but later that same day the client called me again to say it had rebooted again.
I have spoken to HP support in the UK and was told that HP have issues with Service Pack 3 of XP. I found this hard to believe and also embarrassing - this is a new IT support contract and I recommended that all the PC's were upgraded to SP3.
Gareth Davies

I would suggest you upgrade teh drivers for your motherboard and also update the BIOS of your motherboard too and see if that resolves the issue.
Make it easier for other people to find solutions, by marking my answer with \'Accept as Solution\' if it solves your problem.
Click on the BLUE KUDOS button on the left to say "Thanks"
I am an ex-HP Employee.

ASUS Sonicmaster X102BA Win764bit - usb bugcode driver blue screen on sleep

Similar Messages

Maybe you are looking for