Asysnc IO Error: 14: Bad address

Hello,
We are using RHEL4.0 x84_64 Linux system. Oracle 10.2.0.3 database runs on it. We try to run our database as async IO.
We are using veritas vxfs file system type.
After set the oracle parameter filesystemio_option to setall, we got an error from db also from OS.
Database error message belov;
ORA-19502: write error on file "/home/db/log01/1_42895_629465220.dbf", blockno 131073 (blocksize=512)
ORA-27061: waiting for async I/Os failed
Linux-x86_64 Error: 14: Bad address
Additional information: -1
Additional information: 1048576
ORA-19502: write error on file "/home/db/log01/1_42895_629465220.dbf", blockno 131073 (blocksize=512)
ARC1: I/O error 19502 archiving log 6 to '/home/db/log01/1_42895_629465220.dbf'
ARCH: Archival stopped, error occurred. Will continue retrying
Sun Oct 26 08:55:50 2008
dmesg error message;
Vendor: EMC Model: SYMMETRIX Rev: 5772
Type: Direct-Access ANSI SCSI revision: 04
SCSI device sdc: 238540800 512-byte hdwr sectors (122133 MB)
SCSI device sdc: drive cache: write through
SCSI device sdc: 238540800 512-byte hdwr sectors (122133 MB)
SCSI device sdc: drive cache: write through
sdc: unknown partition table
Attached scsi disk sdc at scsi0, channel 0, id 1, lun 147
Attached scsi generic sg2 at scsi0, channel 0, id 1, lun 147, type 0
Vendor: EMC Model: SYMMETRIX Rev: 5772
Type: Direct-Access ANSI SCSI revision: 04
SCSI device sdd: 238540800 512-byte hdwr sectors (122133 MB)
SCSI device sdd: drive cache: write through
SCSI device sdd: 238540800 512-byte hdwr sectors (122133 MB)
SCSI device sdd: drive cache: write through
sdd: unknown partition table
Attached scsi disk sdd at scsi0, channel 0, id 1, lun 149
Attached scsi generic sg3 at scsi0, channel 0, id 1, lun 149, type 0
Vendor: EMC Model: SYMMETRIX Rev: 5568
Type: Direct-Access ANSI SCSI revision: 03
SCSI device sde: 15360 512-byte hdwr sectors (8 MB)
SCSI device sde: drive cache: write through
SCSI device sde: 15360 512-byte hdwr sectors (8 MB)
SCSI device sde: drive cache: write through
sde: unknown partition table
Attached scsi disk sde at scsi0, channel 0, id 2, lun 0
Attached scsi generic sg4 at scsi0, channel 0, id 2, lun 0, type 0
lpfc 0000:12:02.0: 0:0203 Nodev timeout on NPort x144d00 Data: x822 x1 x0
VxDMP5: unknown partition table
VxDMP6: unknown partition table
VxDMP1: p1 p2 p3 p4 < p5 >
VxDMP1: p1 p2 p3 p4 < p5 >
VxDMP1: p1 p2 p3 p4 < p5 >
VxDMP1: p1 p2 p3 p4 < p5 >
SCSI device sdc: 238540800 512-byte hdwr sectors (122133 MB)
SCSI device sdc: drive cache: write through
sdc: sdc3 sdc8
VxDMP6: p3 p8
VxDMP1: p1 p2 p3 p4 < p5 >
VxDMP1: p1 p2 p3 p4 < p5 >
Can you help me ?

Have a look at metalink Note:395350.1
Basically, this document describes it's a problem in DIO (direct IO), which can be tuned using vxtunefs (per filesystem).
The document describes to enlarge the buffer bigger than the described number (which is 1MB)
dynamically: vxtunefs -o discovered_direct_iosz=1572864 /mount/point (replace /mount/point with the oracle mount point(s))
statically in /etc/vx/tunefstab: /dev/vx/dsk/oracle/oravol discovered_direct_iosz=1048577 (replace with your oracle filesystems)

Similar Messages

"mprotect reset: Bad address" Help

Hi,
I am running a server built in java which accepts lots of tcp connections from clients and performs database operations on their behalf.
I compile the server with Suns jdk1.3 but run it with IBMJava2-13.
The following message gets printed to standard error
mprotect: Bad address
mprotect reset: Bad address
Sometimes the jvm crashes after printing this message and sometimes it just hangs taking up 90% of the cpu. At other times it carries on running without problems
I assume this means that there has been a memory access violation. Also the problem seems to be with the jvm rather than my code because if the code had a bug then there would be an indication to the buggy portion of the code along with the above message.
Could it be that the problem is that I am compiling and running the program using different java products? I know that java code is portable in that sense but in the real world this is obviously not the case.

hi , i tried compiling the .java files and running them with IBM jdk , but it still gives the same problems. I have not yet compiled as well as run it using suns' jdk. the problem is that it is very difficult for me to recreate the situation.

I have started to get this error message: 5.1.3 bad address syntax in my email account. I am using Outlook 2011. It does not appear to be affecting sending or receiving email. I have no idea what it means or how to resolve the issue. Any advice?

I have started to get this error message: "5.1.3 bad address syntax" in my email account. I am using Outlook 2011. It does not appear to be affecting sending or receiving email. I have no idea what it means or how to resolve the issue. Any advice? My email account is through Optimum online and I am using Airpost Express.
P.S. The error sound "bong" is driving us nuts!

Please post on the Office for Mac product forums that Microsoft hosts. It's their product and they can best troubleshoot the issue.

Error: 'bad address'

So, I've created an iBook. Closed it. Opened it a few hours later to edit some more. Tried to save it, responding in the error:
"The document 'xxx' couldn't be saved. Bad address."
Now what?

Have a look at metalink Note:395350.1
Basically, this document describes it's a problem in DIO (direct IO), which can be tuned using vxtunefs (per filesystem).
The document describes to enlarge the buffer bigger than the described number (which is 1MB)
dynamically: vxtunefs -o discovered_direct_iosz=1572864 /mount/point (replace /mount/point with the oracle mount point(s))
statically in /etc/vx/tunefstab: /dev/vx/dsk/oracle/oravol discovered_direct_iosz=1048577 (replace with your oracle filesystems)

674 ERROR: Message operation failed because of a bad address

On our tuxedo server we have the following error that is repeatedly writen on its log:
155140.RJODIGD02!sid_server_ro.778390.1.0: ERROR: msgrcv err(LIBTUX_CAT:674: ERROR: Message operation failed because of a bad address): errno=14,qid=27729940,buf=3299838207512,bytes=1049340,type=-1073741824,flag=0
This error does not affect the Server functionality but we would like to know by what could be due:
we have seen the error description but from this we could not find out the real causes:
674 ERROR: Message operation failed because of a bad address
DESCRIPTION
msgsnd to a queue failed because the message pointer is pointing to an illegal address.
ACTION
Check the address of the message queue pointer, or contact your TUXEDO System Technical Support.
Any help is well accepted ......... thanks a lot in advance.
Ciao

Hi,
If I had to guess, I'd say you were looking at a memory corruption problem. The error basically says that when Tuxedo tried to perform a msgrcv() operation on a System V IPC queue, the address of the buffer to receive the message wasn't valid. Although if this is really a memory corruption problem, I'm surprised your server continues to function. You might want to try a memory checking tool to see if your code is writing to memory it doesn't have allocated or writing past the ends of an allocated buffer.
Regards,
Todd Little
Oracle Tuxedo Chief Architect

ESB Portal : The remote server returned an error: (400) Bad Request

Hi,
I am getting the below error message while trying to access ESB Portal:
========================
Event code: 3005
Event message: An unhandled exception has occurred.
Event time: 12/18/2013 12:07:10 PM
Event time (UTC): 12/18/2013 12:07:10 PM
Event ID: 2a429911fb69455ab3b77348c8b259ce
Event sequence: 10
Event occurrence: 2
Event detail code: 0
Application information:
Application domain: /LM/W3SVC/1/ROOT/ESB.Portal-1-130318418493427545
Trust level: Full
Application Virtual Path: /ESB.Portal
Application Path: C:\Projects\Microsoft.Practices.ESB\Source\Samples\Management Portal\ESB.Portal\
Machine name: WIN-HG1MJEC7KJS
Process information:
Process ID: 3220
Process name: w3wp.exe
Account name: NT AUTHORITY\SYSTEM
Exception information:
Exception type: WebException
Exception message: The remote server returned an error: (400) Bad Request.
Request information:
Request URL: http://localhost/esb.portal/default.aspx
Request path: /esb.portal/default.aspx
User host address: ::1
User: WIN-HG1MJEC7KJS\ESBUser
Is authenticated: True
Authentication Type: Negotiate
Thread account name: NT AUTHORITY\SYSTEM
Thread information:
Thread ID: 4
Thread account name: NT AUTHORITY\SYSTEM
Is impersonating: False
Stack trace: at System.Net.HttpWebRequest.GetResponse()
at System.ServiceModel.Channels.HttpChannelFactory.HttpRequestChannel.HttpChannelRequest.WaitForReply(TimeSpan timeout)
Custom event details:
====================
I also looked at thread : http://social.msdn.microsoft.com/Forums/en-US/1fb510a8-9f4b-4e1e-9261-3273b037786c/esbportal-bad-request-400?forum=biztalkesb
However didn't able to find the workaround for the same.
Best Regards,
Harkirat

Hi,
On a local server you don't have to change the web.config if you use local Windows Groups. Check if the User is added to the "BizTalk Server Administrators" Group. Also check if the Group or the User has rights to access EsbExceptionDb & ESBAdmin
database. You also have to enable "Windows Authentication" in IIS for the ESB.Portal.
Local Machine settings:
ESB.Exceptions.Service\Web.config
<connectionStrings><add providerName="System.Data.SqlClient" connectionString="Integrated Security=SSPI;Data Source=.;Initial Catalog=EsbExceptionDb" name="EsbExceptionDbConnectionString"/></connectionStrings>
C:\Projects\Microsoft.Practices.ESB\Source\Samples\Management Portal\ESB.Portal\Web.config
<connectionStrings>
<add name="AdminDatabaseServer" providerName="System.Data.SqlClient" connectionString="Network Library=dbmssocn;Data Source=(local);Integrated Security=True;Initial Catalog=ESBAdmin;"/>
</connectionStrings>
<authentication mode="Windows"/>
<authorization><allow roles="BizTalk Application Users"/>
<allow roles="BizTalk Server Administrators"/>
<allow roles="Administrators"/>
<deny users="*"/>
</authorization>
Kind regards,
Tomasso Groenendijk
Blog
| Twitter
MCTS BizTalk Server 2006, 2010
If this answers your question please mark it accordingly

Ioctl bad address

hi all,
To send data from my dummy driver to user
i used mp->b_cont->b_wptr = "hello to user"
mp->datap->db_cmd=IOCACK,
qreply(q,mp);
but the application ioctl is failing with
bad address why?
Although i gave enough buffer space
to strioctl.ic_dp buffer i.e malloc(50)
even though the data i sent is just 15 characters.
can anybody answer me..
if so thanks in advance
regards
vasu

i tried using rptr but no use..
here the code is in application side
char *buf
buf = (char*) malloc(70)
buf="hello world"
strioctl.ic_timeout=30
strioctl.ic_dp=buf
strioctl.ic_len=strlen(buf)
ioctl(fd,I_STR,&strioctl)
driver code
mp->b_cont->w_ptr++="Good bye world"
error coming is "bad address" why?
if any one has example for sending data from driver
to user application using I_STR ioctl please welcome.
thanks for all who r ready to help me
regards
vasu

Hme0 plump or unplump bad address

my sun solaris 9 machine on boot up looses its IP settings and i get the error configuring IPv4 interfaces config bad address. All its files ie hosts, netmasks , defaultrouter have the rifgt settings. I have tried sys-unconfig and on initial boot up after sys-unconfig the machine comes up well. On the next reboot the machine returns the above error.
Please experts help me out. Why is this so and how do I solve it?

I've just had the exact same problem and now resolved it. I believe the error message is accurate. You should check your /etc/nsswitch.conf file and check that under hosts "files" is typed. The person that removed NIS from my system in question typed "file" not "files" on the "hosts" line. Once fixed everything came online, (the system could resolve the hostname to IP address (via hosts file)). Check that your /etc/hostname.hme0 is a single hostname (not FQDM), and that entry is present in your /etc/hosts file.
HTH
Cheers
Adam

Leopard; "router returned bad address"

i put on my screensaver and was getting ready for bed, when the processor fans started firing up again. the only app i had open was iChat, and it wasn't using anything substantial in terms of CPU. activity monitor showed the same.
until i opened up console and found this message over and over again:
29/10/2007 01:08:04 mDNSResponder[23] handleLNTGetExternalAddressResponse: Router returned bad address
29/10/2007 01:08:04 mDNSResponder[23] Error getting external address 3
see here for a screencap. google/apple discussions provided little to no insight.
lather, rinse, repeat. this happens every 8 seconds or so. what's going on? i have an airport express bridged from a linksys router, and i've never had an issue with it before. resetting both didn't help, firmware's up to date.
any insight would be extremely helpful.
10.5 build 9A581

Maybe its not your router, maybe its mDNSResponder itself..... It doesn't seem to me like a router would randomly begin to hand out bad network addresses unless your access was rejecting itself (ex. your saved password was wrong because you changed the password on another machine and didn't replace the old one in the keychain), or if you were getting DDoSed (Denial of Service attack, which executes malignant code on your system in order to crash/shut it down).
UPnP??? Thats required for certain network access...... Not sure what would be affected off the top of my head though, I guess... you'll just have to wait and see.
Are you absolutely sure your not getting these errors anymore with UPnP disabled?

HELP........CANT CREATEOUIPROCESS BAD ADDRESS

I'm experimenting with linux and trying to install 8i.
Can anyone please help me.
I got stuck since OUI wont start...............
I get the error ..........CANT CREATEOUIPROCESS BAD ADDRESS.
Help.......please.
Willy
null

I was getting the same thing. It seemed to work when I executed
/mnt/cdrom/install/linux/runIns.sh instead of
/mnt/cdrom/runInstaller
Now I just have a problem where it doesn't seem to install the
TCP/IP protocol...
Joe Hoot (guest) wrote:
: I am using RH Linux 6.1, AMD K62 3DNow, 128ram, 128M swap. I
: have downloaded Oracle Standard 8i 8.1.5 Server and untared
it.
: I have setup environment variables, users, groups,
directories,
: and downloaded jre116_v5 and made a link to it
: in /usr/local/jre. When I loggin as oracle user and go to the
: location of the install files and run ./runInstaller, it gives
: me the follwing:
: Initializing Java Virtual Machine from
/usr/local/jre/bin/jre.
: Please wait...
: Error in CreateOUIProcess(): -1
: : Bad address
: Any suggestions?
null

CreateOUIProcess(): -1 : Bad address install prob

I am using RH Linux 6.1, AMD K62 3DNow, 128ram, 128M swap. I
have downloaded Oracle Standard 8i 8.1.5 Server and untared it.
I have setup environment variables, users, groups, directories,
and downloaded jre116_v5 and made a link to it
in /usr/local/jre. When I loggin as oracle user and go to the
location of the install files and run ./runInstaller, it gives
me the follwing:
Initializing Java Virtual Machine from /usr/local/jre/bin/jre.
Please wait...
Error in CreateOUIProcess(): -1
: Bad address
Any suggestions?
null

I was getting the same thing. It seemed to work when I executed
/mnt/cdrom/install/linux/runIns.sh instead of
/mnt/cdrom/runInstaller
Now I just have a problem where it doesn't seem to install the
TCP/IP protocol...
Joe Hoot (guest) wrote:
: I am using RH Linux 6.1, AMD K62 3DNow, 128ram, 128M swap. I
: have downloaded Oracle Standard 8i 8.1.5 Server and untared
it.
: I have setup environment variables, users, groups,
directories,
: and downloaded jre116_v5 and made a link to it
: in /usr/local/jre. When I loggin as oracle user and go to the
: location of the install files and run ./runInstaller, it gives
: me the follwing:
: Initializing Java Virtual Machine from
/usr/local/jre/bin/jre.
: Please wait...
: Error in CreateOUIProcess(): -1
: : Bad address
: Any suggestions?
null

NIO Bug Bad Address Exception

I've been developing a file transfer system using the transferTo and transferFrom methods. My method will throw intermittently IOExceptions
"Bad address". Has anyone else seen this? There is a bug report out on this however it was not reproducible. We are able to reproduce this error
at an alarming rate. I am using java 1.4.0_01.

There is a bug in 1.4.0.01 and there is no work around. I was force to use the old IO classes, and tweek the Garbage collector, and classes to ensure maximum through put. I was informed by the Java Team that this problem was fixed in 1.4.1. I that is not the case you will have to submit another bug report.

Tscr bad address in IPSec tunnel configure

Hi all,
beforehand I'm apologize for my stupid question, but I'm a beginner in Solaris 10 administrations.
I've a problem with IPSec ip.tun0 configuration.
I've folloowing configuration of network:
nirvana:/# ifconfig -a
lo0: flags=2001000849<UP,LOOPBACK,RUNNING,MULTICAST,IPv4,VIRTUAL> mtu 8232 index 1
inet 127.0.0.1 netmask ff000000
ife0: flags=1100843<UP,BROADCAST,RUNNING,MULTICAST,ROUTER,IPv4> mtu 1500 index 2 inet 10.10.254.253 netmask ffff0000 broadcast 10.10.255.255
ether 0:19:db:c1:22:f0
rtls0: flags=1100843<UP,BROADCAST,RUNNING,MULTICAST,ROUTER,IPv4> mtu 1500 index 3
inet 192.168.250.252 netmask ffffff00 broadcast 192.168.250.255
ether 0:30:4f:25:e7:76
lo0: flags=2002000849<UP,LOOPBACK,RUNNING,MULTICAST,IPv6,VIRTUAL> mtu 8252 index 1
inet6 ::1/128
ife0: flags=2100841<UP,RUNNING,MULTICAST,ROUTER,IPv6> mtu 1500 index 2
inet6 fe80::219:dbff:fec1:22f0/10
ether 0:19:db:c1:22:f0
rtls0: flags=2104841<UP,RUNNING,MULTICAST,DHCP,ROUTER,IPv6> mtu 1500 index 3
inet6 fe80::230:4fff:fe25:e776/10
ether 0:30:4f:25:e7:76
nirvana:/#
When I typed following - second command ending with error ;-(((
nirvana:/# ifconfig ip.tun0 plumb
nirvana:/# ifconfig ip.tun0 10.10.254.1 10.10.254.2 \
tscr 192.168.250.252 tdst 192.168.250.222ifconfig: tscr: bad address
nirvana:/#
Help mi please.
Thank's very much for yours advice.
Bye

Disclaimer
The Author of this posting offers the information contained within this posting without consideration and with the reader's understanding that there's no implied or expressed suitability or fitness for any purpose. Information provided is for informational purposes only and should not be construed as rendering professional advice of any kind. Usage of this posting's information is solely at reader's own risk.
Liability Disclaimer
In no event shall Author be liable for any damages whatsoever (including, without limitation, damages for loss of use, data or profit) arising out of the use or inability to use the posting's information even if Author has been advised of the possibility of such damage.
Posting
Generally, by default, Cisco tunnel encapsulation will copy the original packet's ToS to the tunnel packet's ToS. (I.e. all you need to do is insure your original packet's ToS is as desired.)
Regarding MPLS vendor QoS support - that's vendor specific - often they offer different QoS models - sometimes they charge for QoS features (i.e. you need to talk with them).

Adobe Photo Downloader has encountered a problem and needs to close. We are sorry for the inconvenience. Error Code: c0000005 Address: 76f73ac3 I clicked on the OK button and the downloader closed. I then tried to download from the organizer. I

Photoshop Elements 12
Adobe Photo Downloader has encountered a problem and needs to close. We are sorry for the inconvenience.
Error Code: c0000005
Address: 75e32f71
I clicked on the OK button and the downloader closed.
I did a search on this error code (c0000005) and there seems to be a workaround but no solutions, why is this? I ask that because this problem seems to be years and years old, going back to at least 2005 (do the math that is 10 years).
I don't even have the Camera hooked up and I get this error on download. I redownloaded everything and reinstalled. I allso saw the AVI issues reported with this proble so i updated Quicktime though without the camera being hooked up when I get this error I didn't expect that to work. I tried support and they wouldn't help because I bought it in March this year. Pretty frustrating as I have re-purchased Elements about every 2 years. I think I might need a new CODEC? I had this problem on an Earlier version And I seem to remember that being the Fix but this may be something completely different

I finally found that it was missing a picture so the Catalog was "corrupted". I just deleted the picture and it started working.
I hate Adobe and their total lack of support - thanks for nothing Adobe . Also get this - they offered me to upgrade to 13.0 ( My 12.0 is only 6 months old but they still don't support it on errors. Only install errors!
I have upgrade and repurchase this product 4 times now. I will find something else next time!

After upgrading to Yosemite, Thunderbird does not recognize email addresses: "syntax error" in recipient address. Fix?

After upgrading to IOS Yosemite, Thunderbird will no longer send emails to the contacts in my history file that drops down when I "write" a new message. I continue to get a return response that there is a syntax error in the address field of the message although I have tried both my stored emails and manually typed email addresses. What has been changed and how do I recover the use of Thunderbird's great program?
By the way, how do I eliminate out of date email addresses from popping up and populating email responses rather than the most current ones that are in my contacts? I now have to type each one in separately as the default options that come up are many out of date.
Thanks much for your great work. Mozilla and Firefox are the best.

Did you find a solution to this issue? My mail server is doing the same thing. I've tried six migrations now, and have a couple of tickets open, but they all have issues. I have worked around all of them except the mail server problem.
I did some more digging; the problem appears to be that on a migrated server, it leaves all of your mail store in the old location, doesn't move it, and then doesn't appear to upgrade spam-assassin properly. The net effect is that the mail server gets the SMTP communication, tries to pass the message into spam assassin, and then it goes south.
I see errors like this littered in the logs:
Jul 31 13:53:10 mail org.amavis.amavisd[5927]: bayes: cannot open bayes databases /var/amavis/.spamassassin/bayes_* R/O: tie failed:
Jul 31 13:53:10 mail org.amavis.amavisd[5927]: bayes: cannot open bayes databases /var/amavis/.spamassassin/bayes_* R/O: tie failed: No such file or directory
Do you see anything similar?

Asysnc IO Error: 14: Bad address

Similar Messages

Maybe you are looking for