At a loss with basic setup

I?m at a loss with this whole avs3120 accelerator and the css11503. I thought this would be a seamless integration. Can anyone out there help me because at this point I?m about to give up on this thing. Here?s what I have: an avs 3120, avs 3180 (mgmt), css11503, and two PeopleSoft servers. Everything is directly connected to 6509 so AVS isn?t directly connected to CSS. At the very least, all I want to do is utilize the AVS for the PeopleSoft server. No magic or anything, I just want to see this thing work.
The url that I want the users to resolve to is http://psftavs.domain.com
- Which is the ip of the AVS, let?s say 192.168.250.173
- Currently there?s no application specific configs on the AVS, just the default setting
- Destination mapping is: default -> 192.168.250.247 PROTOCOL=clientprotocol
- This is a vip on the CSS that?s pointing to the two servers.
1) Is my destination mapping correct?
2) Should my destination mapping from the AVS, be pointing to the server IP addresses?
3) I don?t have any configs on CSS for this, do I need a redirect statement or something? I don?t want the URL to change.
I get nothing when I type in the url psftavs.domain.com; however, the vip URL works which is psftprd.domain.com; I basically get my PeopleSoft login page and can log in.
If you need more information let me know. I have a generic diagram to help out with my layout, not sure if I?m explaining myself correctly.
Regards,
Thai

The detination mapping should point to the server's ip address. On the AVS 3120 appliance, the left-most interface (Ethernet 1) is used for management console connectivity.
http://www.cisco.com/en/US/docs/app_ntwk_services/data_center_app_services/avs/v60/release/notes/AVS60RN.html

Similar Messages

Problems with basic setup

hello, yesterday I have bought a wireless-G Broadband Router (WRT54G).
I think I have connect everything fine. But when I open the basic setup (http://192.168.1.1/) and I give my password I get this: http://users.skynet.be/fa853774/test/netwerk.JPG .
I don't see everything ( the buttons at the top and on the left side,... ).
Can somebody tell me what's going on and what I can do?

hi !
U will need to reset the router for 3 min while the router is powered on ...if possible u can also upgrade the firmware for the router .. U can upgarde the firmware through tftp.exe while u can find the TFTP.exe on the following link
:- ftp://ftp.linksys.com/pub/network/
Network Security Administrator (EC Council)
linksysfirmwares.googlepages.com/

Newbie help with basic setup - WRK54G

=== Linksys WRK54G v2 router
=== WinXP Pro SP3
I am not a networking person, and I need help setting up my router. I bought it new a bit over a year ago and installed it successfully, but it kept hosing up my connection so I took it off line and put it up. My wife now has a laptop and so I want to try this router again. It's powered on and connected to my DSL and my laptop, which is my main computer.
Power light: ON
WLAN light: ON
1 light: ON
Internet light: ON
I have the CD's software on my hard drive and tried setting things up with the EasyLink_Connect.exe, PCConnect.exe, and even did the ELADownloadInstaller.exe, which downloaded some other installer (EasyLink Advisor?). None of them worked. They crapped out at the point where it detects the router and read cannot detect router.
I read in the PDF manual that the router settings can be reset to defaults and so I did and tried again. No joy. I also tried unplugging too without results.
So, what do I do now to get this thing working?
Help is much appreciated.

If you face any further problems you should try this -
Hard reset your router and then re-configure it...
Press and hold the reset button for 30 seconds...Release the reset button...Unplug the power cable from your router, wait for 30 seconds and re-connect the power cable...Now re-configure your router...
If your Internet Service Providor is Cable follow this link
If your Internet Service Providor is DSL follow this link

Help With My Setup...

I Hope I'm in the right forum, If not let me know where this post should go.
Thanks for helping me out. I have some questions regarding my setup and acquiring new gear. Currently, I have a the following setup:
IMac - newer model
Logic Pro 9
Numark tt-usb turntable
Stanton DJ mixer
Pair of Yamaha HS80 monitors
MPD 24
I would like to add a keyboard controller (I'm thinking of the new Korg Microsampler). Basically, I'm willing to get the microsampler as long as it can Fully function like a controller, which can control logic synths & plug-ins(axiom, mpk, etc.) and as well as it's own features. Furthermore, I would like to to be able to record from my turntable to logic and into the microsampler. I understand I would need an interface. Would I still need the mixer? Would the M-Audio Firewire Solo work with my setup?
Would a control surface take place of an Interface?
I am possibly interested in getting a control surface that works good within logic. I was looking at the Euphonix MC Control, it seems to work great with logic. Is there an cheaper alternative? Also, I would like it to be user friendly, I am new to this.
Essentially, I want everything to work simple & smoothly. I like to make sample based music from records. Can you give me a rundown of the necessary items I'm going to need...cables, interface, etc.
Sorry, if I'm rambling just want to be clear.
I appreciate your time....

I use a Alesis multimix FW and a presonus inspire.
I would guess that you should always get dry sound from any output with firewire plugged in or not. My inspire uses a software control panel to route signal and the Multimix is all hardware. I have no clue how to route signal with the firebox but it has to be one or the other. Presonus is pretty good with updates and bug fixes did you check for new drivers?

Need some help with VAT Setup

Here is my scenario.
We're dealing with a partner in Germany. We will be shipping them parts from the US and need to slap on a 19% VAT surcharge when invoiced.
I can get the VAT to calculate correctly on the SO and Invoice, the issue is that it will not post to accounting because of the below error:
Tax statement item missing for tax code O1
Here is my setup:
I am using condition type MWST, access sequence Country(US)/Destination Country(DE) Amount 19%, Tax Code O1
In OB40, under key MWS, I have the GL account entered for the Tax Code and Accounts are determined for Tax Code.
I looked at the GL itself and in the control section, the tax category has a * meaning all tax types are allowed. It's also configured to post w/o a tax code present.
I'm at a loss, is my setup missing something or completely incorrect?

After kicking this around for a few days I'm still lost as to the issue
The new error I get is "Condition type MWST tax code O1 does not exist".
"When calculating tax, the system tried to determine the
condition amount and the condition number from tables A003
and A053 using the specified condition type and tax code.
However, no values were found there."
I discovered this SoldTo had a jurisdiction code and as soon as I removed it, I got past the earlier error and run into this one now. It appears it defaults to the jur. code for our main office if one isn't assigned to the sold to. I looked at these tables and these are the condition tables behind the MWST access sequence for tax condition types.
Here is my scenario again, please help me confirm I am approaching it the right way.
Need to collect 19% VAT when shipping from US plant to Germany.
I am using condition type MWST on the pricing procedure and this has an entry in VK13 to apply the 19% tax based on source/destination country. This seems to be working, it pulls it in ok onto the order in the tax field. I am using tax code O1 in the VK13 entry. I assume this is used in conjunction with the TAXUSJ procedure and will be used to calculate the right tax amounts.
I assume that since the source country is US, the tax calculation procedure TAXUSJ is where I need to do any config. I added a MWAS condition type which points to AccKey MWS. However, in FTXP I cannot enter in any percentage here. The field is greyed out. Within VK12, the only options I have for tax codes are from TAXUSJ.
I'm assuming that when trying to post to accounting this is where it's getting stuck since it can't find an entry in the condition tables behind this.
Can someone who's more of an expert on this please confirm my approach is correct. How can I get this tax in the TAXUSJ procedure?

Basic setup for Cisco RV325 router

I am having problem with the basic setup of RV325 router.
Example:
STEP 1 Connect a PC to a numbered LAN port on the device. If the PC is configured to
become a DHCP client, an IP address in the 192.168.1.x range is assigned to the
PC.
Which LAN port does it meant?
I tried the router connection on different LAN ports to a PC but the browser would not launch anything at 192.168.1.1.
Can anyone help?
Thank you.

Hello,
It sounds like you are trying to access the web interface of your router so you can configure it. First of all, I'll go over the ports of the router with you.
The last port of each row (on the right side) of the device is for the WAN (Wide Area Network) that's designated for where you connect to your ISP (Internet Service Provider). Most likely, you will connect your modem to one of those ports. Any ports to the left of those are your LAN ports (Local) where you can connect your PC.
Once you connect to one of those ports, your PC should get an IP address. If you are unable to get to the web interface of the router, you will want to confirm your IP address and default gateway (which is the IP address of the router).
This can be done in Windows by:
Select Start > Run. Type command or CMD into the dialog box, then click OK.
In the resulting command line window, type ipconfig.
C:\>ipconfig
You will see something similar to this resulting output:
Ethernet adapter Local Area Connection:
Connection-specific DNS Suffix . :
Description . . . . . . . . . . . : 3Com EtherLink 10/100 PCI For Complete PC Management NIC (3C905C-TX)
Physical Address. . . . . . . . . : 00-01-03-AB-0E-6P
DHCP Enabled. . . . . . . . . . . : Yes
Autoconfiguration Enabled . . . . : Yes
IP Address. . . . . . . . . . . . : 192.168.1.10
Subnet Mask . . . . . . . . . . . : 255.255.255.0
Default Gateway . . . . . . . . . : 192.168.1.1
This will give you 3 key pieces of information you will want to verify. First, you want to see that your network adapter is set to DHCP. It should say yes next to it. Second, your IP address needs start with 192.168.1.x
In this example, it is 192.168.1.10, which is fine.
Lastly, your default gateway should be preset to 192.168.1.1. If it is not, write that number down and try to access that IP address in your browser.
Note: If your browser is just coming up blank, you may want to try a different browser.
Hopefully you'll be able to get into your router at this point. If not, please provide the output of your IP config statement so we can further troubleshoot your issue.

Custom Installer with Inno Setup (reduce size of Run-Time and VISA RT)

Hi,
we are using Inno Setup to install our Application. Up to now i include the full LabView 2009 SP1 Run-Time and the full VISA-RT
(that are 302 MB). I have also made an installer using the internal tools of LV and the setup is only 163 MB. The LV removes
some parts of the RunTime libraries.
We are using only these parts:
p0 MetaUninstaller\
p1 VC2005MSMs\
p10 NI-RPC\
p11 XercesDelayLoad27\
p12 NI-ORB\
p13 NI-DIM\
p14 NI_TraceEngine\
p15 NI-PAL\
p16 NI_Logos_XT\
p17 TDMS\
p18 MDFSupport\
p19 MKL_900\
p2 VC2008MSMs\
p20 NI_Logos\
p21 RT\
p3 NI_Certificates\
p4 NI-VISA_Runtime\
p5 LabVIEW_RT_NBFIFO_90\
p6 Service_Locator\
p7 LabVIEW_Web_Server_RTE_90\
p8 LabVIEW_WebServices_RTE_90\
p9 mDNS_Responder\
1. Is it allows to do that also using Inno Setup? I mean, am I allowd to do that? The license from
NI etc. are all included. I want to save disc space...
2. Is that wise? If not, why?
Thanks

Hello sjunge,
basically there should be no problem installing the software with Inno Setup as long as you do not violate the License Agreements.
But keep in mind that there could be dependencies between the installers you install and those you don't and you may run into trouble with the software later on
Kind regards
Carsten

Is clustering possible with this setup.

Is it possible to use
Windows Server 2012 Data Center
2 SuperMicro AS-2022G-URF4+ R with
RAID CARD SUPERMICRO|AOC-USAS2-L8i and SAS drives for a failover cluster for Hyper-V
At this moment using mirrored drives for operating system and 4 drives free for the cluster itself if possible with two slots open.

Is it possible to create shared storage with this setup that will work with the cluster or do I need a SAN.
At least now you need to deploy a third-party software doing something similar to the picture below:
So basically you'll take a bunch of a locally attached disks and "mirror" them with a software
component. If you're already having all-SAS setup (something you really do) you can deploy
what's called "Clustered RAID Controllers" config replacing SAS HBAs you use now. See:
LSI Syncro
http://www.lsi.com/products/shared-das/pages/default.aspx
8i does not need SAS JBODs to create a fault tolerant config and 8e needs external enclosures.
P.S. I would not deploy any "magic hardware" as it's a vendor lock-in. You can change software vendor
easily but I'm not aware of anybody doing similar things to what LSI does.
StarWind VSAN [Virtual SAN] clusters Hyper-V without SAS, Fibre Channel, SMB 3.0 or iSCSI, uses Ethernet to mirror internally mounted SATA disks between hosts.

Basic Setup Web Page Error

When I type in the IP address of the router in the address bar, the page comes up with errors and none of the tabs at the top of the page are showing, meaning I can't click on "Wireless". My router and adapter are showing a connection, but it tells me there is no internet connection found. Which is why I need to access the Basic Setup page. I've tried turning off my pop-up blocker, but no use. If someone could help me I would be grateful!

>reset
>reconfigure
>what happened?
>same thing?
>upgrade firmware using TFTP file (download this one from FTP website)
>reset
>reconfigure
I do know everything, just not all at once. It's a virtual memory problem.

Linksys WRT54G V8 Basic Setup page problems

I have been trying to change my password and all the settings on my WRT54G V8 router today because I forgot the password, and I can't seem to navigate the Basic Setup page. I can log in (most of the time) after resetting the router, but whenever I try to click on a different tab (like "Wireless", or "Security") it comes up with the page saying "This Page Cannot Be Displayed." I'd like to be able to put a password on it (which I have successfully done before on this router) because I live in a college dorm and would like to keep my internet from being bogged down by other people using it.
Any help would be greatly appreciated.

Tatonka,
I assume you downloaded the WRT54G setup software disk into your PC initially. Reset the router (hold in the reset button for 30 seconds), hard wire your PC to the router, and access the Linksys icon on your desktop. Just follow the prompts after that. I had to do exactly this at my daughter's home last evening. Bob

Only Basic Setup Tab

My linksys router WRT54GS has defaulted its router name to a generic name. As i follow the instructions to access the set up screen (through 192.168.1.1), I only have a limited number of tabs on the SETUP screen (Basic Setup, MAC Address and Advanced Routing) - none of which provides access to the router name or SSID. What am I missing? Thanks!

Reset and power cycle the router. Usually that problem occurs if there’s a problem with the router’s current firmware or with the browser that you are using. As such, upgrade the router’s firmware if there is a newer firmware available then try to use another browsers or better yet try to use another computer.

WRT160Nv2 - Basic setup page not usable

Hello,
I've been using a WRT160Nv2 for almost 1 year now and it works fine.
Since today, I can't access to the configuration page under (192.168.1.1). Actually the page is displayed, but the menu and all the labels are missing. So I can't do any configuration. Firmware version seems to be v2.0.02 (appears on the top-right of the basic setup page).
I already reconfigured the router with the installation setup. Didn't help.
I tried to updated the firmware with tftp.exe but get an error 'Server could not be accessed' and the i have to restart the computer to see the router again.
Can anyone help ?
Regards,
CHReg

Hard reset the router by pressing the reset button for 30 seconds and release. Wait 30 seconds and power cycle the router. Now connect via wired computer to 198.162.1.1 username blank password admin and reconfigure the router from scratch.

Cannot store basic setups on Camileo S10 and P30

Hello, first post for me. I had a Camileo S10 and changed it with a Camileo P30, and on both camera I cannot save some basic setups. I have to set them every time a use the camera. For example,if I activate the stabiliser in 720P, than a shoot a video, than a close the camera, than 5 min later I have to ashoot another video, I always have to go to settings and re-setup stabiliser on, as this setting do not remain stored while the 720p setup stay stored. Same for photo shooting, where light conditions and so on have to be setup every time. This is very annoying, and I cannot ask my son to do not move for a picture, if every time I open the camera I have to redo the setups... Do I do something wrong here? Is there a way to save the setups, like in most of the normal camera and camcorder?
Many thanks,
lillo

Hello Mores,
batteries and full load done and ok...
Yes, I know the stabiliser can be set only with 720p, but here I refer also to normal basic camera settings, like light, expositions and so on. They have to be set every time you open the camera. Imagine you are in a party one evening and every picture you take, youhave to reset the camera from scratch, exposure, night setup, tungsten filament light... these settings are not "remembered" by the camera... On the contrary date and time are properly stored. I really hope this will be solved in a firmware updates...
Thanks,
Lillo

At a loss with phone line and broadband

Hi,
First of all, sorry for cross posting this, but as you might gather I'm currently stuck between a rock and a hard place.
http://community.bt.com/t5/Phones/At-a-loss-with-phone-line/td-p/54639
I'm not going to repeat everything in that post, just to say when all equipment is unplugged and you get crackles and white noise through the phone, it can not be equipment, no matter how intermittent. Am I correct?
The main reason for cross posting is around the annoying BRAS IP profile. It seems that for 30mins of static, I get stuck on a 130k profile for 3days. I could cope with the occasional outage or slow down, but 3days is half a week and when you have the recent bad weather, you get 1day of decent profile before the next spat! As a result of this, I would like to see if anyone else in the community has been through similar?
I will point out that I have been working in IT for 13years, so I like to pretend that I know something about things, but I must say that BT is one of the only companies that I deal with and dealt with that seem insistent on blaming the customer for everything.
Connection information
Line state Connected
Connection time 0 days, 1:44:21
Downstream 2,048 Kbps
Upstream 448 Kbps
ADSL settings
VPI/VCI 0/38
Type PPPoA
Modulation ITU-T G.992.1
Latency type Interleaved
Noise margin (Down/Up) 9.6 dB / 19.0 dB
Line attenuation (Down/Up) 53.0 dB / 29.5 dB
Output power (Down/Up) 17.8 dBm / 12.1 dBm
Loss of Framing (Local) 0
Loss of Signal (Local) 0
Loss of Power (Local) 0
FEC Errors (Down/Up) 5261636 / 45
CRC Errors (Down/Up) 0 / 2147480000
HEC Errors (Down/Up) nil / 28
Error Seconds (Local) 134
Solved!
Go to Solution.

No I'm suggesting the mod team is preferable to calling India ....
What they do with you is down to them .... and you.
Allbeit I doubt you'll see a profile reset, but even better you may see a lasting resolution, hopefully.

Web Service Call with Basic Authentication does not work

If I try to use Basic Authentication in my Web Service Client with the automatically created methods
setUsername(inUserName)
setPassword(inPassword)
setAddress(inAddress)
the application does not make a call. Did I forget something?
Is it possible to use "Test Method" with Basic Authentication?
Thank you.

Thank you for your answer.
But: I already read this article. And it doesn't help me.
I use the following code:
            getMyServiceClient1().setUsername(inUserName);
            getMyServiceClient1().setPassword(inPassword);With this code I always get a java.lang.NullPointerException.
The methods setUsername and setPassword are definded as follows:
public void setUsername(String inUserName) {
        myStub._setProperty(Stub.USERNAME_PROPERTY, inUserName);
public void setPassword(String inPassword) {
        myStub._setProperty(Stub.PASSWORD_PROPERTY, inPassword);
}But if I look at the methods which are generated automatically by Sun Java Studio Creator I cannot find _setProperty.
I also found this thread in your forum:
http://swforum.sun.com/jive/thread.jspa?forumID=123&threadID=54773

At a loss with basic setup

Similar Messages

Maybe you are looking for