AT&T DSL & Cisco ASA 5505 Problems
Okay I have been working with a 5505 for two days and finally got it configured and working on an AT&T DSL Modem then when I took the 5505 to the clients office and connected/configured it to their AT&T DSL with their IPs the whole thing quite working. I noticed walk through the Tech discussions that there are lots of problems with AT&T DSL deployments and I also discovered that one working configuration was attached to a DSL in AT&Ts standard deployment as a DHCP router using dynamic IPs while the second is in bridge mode using static IPs.
So here's the question why won't the DSL Modem in bridge mode not work as a typical Internet connection like a Cable Modem? I have a Cisco Wireless VPN 4400 to it in bridge mode using static IPs and it works great and on the 4400 there are no special PPPoe settings that have to be set just standard IPs, DNSs, Gateways, Masks...
I see in the Cisco Tech Notes that it is recommended/mandatory to configure Vpdn groups and the Vlan2 to take into account the PPPoe configuration of the AT&T DSL Modem but if the DSL modem is already set in bridge mode and is handling the PPPoe authentication why does the 5505 have do it again this see,s redundant. Will try to use the example configuration additions above and post here with the results.
BTW the configuration with the DSL set as DHCP Router works without any special PPPoe configs.
Very puzzling this DSL configuration conundrum... Last point for businesses if you can use Cable or nonDSL ISP you should do so this AT&T stuff is for the birds... Angry Birds...
Thanks for the assistance in advance!!!
If static ip address:
vpdn group INTERNET request dialout pppoe
vpdn group INTERNET ppp authentication {chap|mschap|pap}
vpdn group INTERNET localname setroute
pppoe client vpdn group INTERNET
mtu outside 1492
Sent from Cisco Technical Support iPad App
Hi Ferdinand. I don't know what a Smartnet contract is. How do I know if we have one? This ASA basically hasn't been touched for 5 years. Almost the entire staff has rotated through this company since then and nobody knowns anything. I found the invoice for it this morning after accounts searched for it, but it appears to have been purchased from a non services retailer. I contacted them and while they confirm they sold it to us they know nothing about it. They don't offer service.
What are my options?
Similar Messages
-
Cisco ASA 5505 - problems getting support
My employer has an ASA 5505 device that has been here longer than any body working here. I've tried to get my hands on some updated software or support but to little avail. I've contacted Cisco support online and they keep telling me to contact my Cisco service sales representative. Now that would be fine if anybody could remember who they are. I suspect they are not even in business anymore.
Not particularly helpful at the end of the day.
I am very close to throwing in the towel with this Cisco. All I want to do is upgrade the firmware to address some known issues we are experiencing with our current firmware.
Any other avenues I am missing?Hi Ferdinand. I don't know what a Smartnet contract is. How do I know if we have one? This ASA basically hasn't been touched for 5 years. Almost the entire staff has rotated through this company since then and nobody knowns anything. I found the invoice for it this morning after accounts searched for it, but it appears to have been purchased from a non services retailer. I contacted them and while they confirm they sold it to us they know nothing about it. They don't offer service.
What are my options? -
Cisco ASA 5505 - problem with negotiating IP address from PPPoE
Hi all,
I have problem with negotiating IP address from PPPoE. There is following design: ISP providing vDSL ending on VDSL modem in bridge mode. Behind brigde modem is ASA 5505 terminting PPPoE on OUTSIDE. Everything works fine except negotiating IP address from PPPoE server.
I have configured ASA 5505 with (ASA Version 9.2(2)4) for PPPoE like this [1.]. But If i try to "show" IP address on OUTSIDE interface a get this [2.], ok strange but let's continue. If list "show vpdn pppinterface id 1" i get this [3.]. Seems that I got public IP addres what was right, but this IP address was not associated with interface OUTSIDE?
Well, if I set IP address manually like this [4.] and also set a default route everything works fine but what will happen when ISP change reservation for my IP address or default gateway.
I have tried different version of ASA OS like 8.4, 9.1 but without luck.
Can anybody help me. Thanks a lot.
Regards
Karel
[1.]
interface Vlan100
description >>VLAN pro pripojeni do internetu<<
nameif OUTSIDE
security-level 0
pppoe client vpdn group O2
ip address pppoe setroute
vpdn group O2 request dialout pppoe
vpdn group O2 localname O2
vpdn group O2 ppp authentication chap
vpdn username O2 password *****
interface Ethernet0/0
description >>uplink O2 vDSL<<
switchport access vlan 100
[2.]
ciscoasa(config-if)# show ip address vlan 100 pppoe
ciscoasa(config-if)# 0.0.0.0 255.255.255.255 on Interface: OUTSIDE
ciscoasa(config-if)# show interface vlan 100 detail
Interface Vlan2 "OUTSIDE", is up, line protocol is up
Hardware is EtherSVI, BW 100 Mbps, DLY 100 usec
Description: >>VLAN pro pripojeni do internetu<<
MAC address f44e.05d0.6c17, MTU 1492
IP address unassigned
Traffic Statistics for "OUTSIDE":
28 packets input, 1307 bytes
31 packets output, 721 bytes
0 packets dropped
1 minute input rate 0 pkts/sec, 3 bytes/sec
1 minute output rate 0 pkts/sec, 1 bytes/sec
1 minute drop rate, 0 pkts/sec
5 minute input rate 0 pkts/sec, 0 bytes/sec
5 minute output rate 0 pkts/sec, 0 bytes/sec
5 minute drop rate, 0 pkts/sec
Control Point Interface States:
Interface number is 15
Interface config status is active
Interface state is active
[3.]
ciscoasa(config-if)# show vpdn pppinterface id 1
PPP virtual interface id = 1
PPP authentication protocol is CHAP
Server ip address is 88.103.200.41
Our ip address is 85.71.188.158
Transmitted Pkts: 20, Received Pkts: 16, Error Pkts: 0
MPPE key strength is None
MPPE_Encrypt_Pkts: 0, MPPE_Encrypt_Bytes: 0
MPPE_Decrypt_Pkts: 0, MPPE_Decrypt_Bytes: 0
Rcvd_Out_Of_Seq_MPPE_Pkts: 0
ciscoasa(config-if)# show vpdn session state
%No active L2TP tunnels
%No active PPTP tunnels
PPPoE Session Information (Total tunnels=1 sessions=1)
SessID TunID Intf State Last Chg
22298 2 OUTSIDE SESSION_UP 561 secs
[4.]
interface Vlan100
description >>VLAN pro pripojeni do internetu<<
nameif OUTSIDE
security-level 0
pppoe client vpdn group O2
ip address 85.71.188.158 255.255.255.255 pppoe setroute
route OUTSIDE 0.0.0.0 0.0.0.0 88.103.200.41 1You're right that the ACL should not affect otherwise allowed communications to the interface address.
Try disabling the ip audit feature on your outside interface.
no ip audit interface OUTSIDE AP_OUTSIDE_INFO
no ip audit interface OUTSIDE AP_OUTSIDE_ATTACK -
Cisco ASA 5505 - problem with ssh, icmp on OUTSIDE interface
Hi all,
I have a very strange problem with OUTSIDE interface and remote ssh. Well, I have followed documentation and configure remote access for ssh like this [1.]. If I want to connect from internet to OUTSIDE interface [2.] get no response and in log I can see this message [3.]. I really do not understand why is ssh connection dropped by OUTSIDE access-list [4.]? If I understand documentation correctly there is no impact for remote mangement/access like icmp, ssh, http(s) by interface access-list. So, why?
When I try ssh connection form internal network to INSIDE interface everything works fine and I can log in to ASA. If I try allow ssh in OUTSIDE access-list still no success and a get this message [5.]? It is strange, isn't?
The same problem with icmp if I want to "ping" OUTSIDE interface from internet a get thish message in log [6.] and configuration for ICMP like this [7.].
Full ASA config is in attachment.
Can anybody help how to fix it and explain what is exactly wrong.Thanks.
Regards,
Karel
[1.]
ssh stricthostkeycheck
ssh 10.0.0.0 255.255.255.0 INSIDE
ssh 0.0.0.0 0.0.0.0 OUTSIDE
ssh timeout 60
ssh version 2
ssh key-exchange group dh-group1-sha1
ASA-FW01# show ssh
Timeout: 60 minutes
Version allowed: 2
10.0.0.0 255.255.255.0 INSIDE
0.0.0.0 0.0.0.0 OUTSIDE
[2.]
ASA-FW01# show nameif
Interface Name Security
Vlan10 INSIDE 100
Vlan20 EXT-VLAN20 0
Vlan30 EXT-WIFI-VLAN30 10
Vlan100 OUTSIDE 0
ASA-FW01# show ip
System IP Addresses:
Interface Name IP address Subnet mask Method
Vlan10 INSIDE 10.0.0.1 255.255.255.0 CONFIG
Vlan20 EXT-VLAN20 10.0.1.1 255.255.255.0 CONFIG
Vlan30 EXT-WIFI-VLAN30 10.0.2.1 255.255.255.0 CONFIG
Vlan100 OUTSIDE 85.71.188.158 255.255.255.255 CONFIG
Current IP Addresses:
Interface Name IP address Subnet mask Method
Vlan10 INSIDE 10.0.0.1 255.255.255.0 CONFIG
Vlan20 EXT-VLAN20 10.0.1.1 255.255.255.0 CONFIG
Vlan30 EXT-WIFI-VLAN30 10.0.2.1 255.255.255.0 CONFIG
Vlan100 OUTSIDE 85.71.188.158 255.255.255.255 CONFIG
ASA-FW01# show interface OUTSIDE detail
Interface Vlan100 "OUTSIDE", is up, line protocol is up
Hardware is EtherSVI, BW 100 Mbps, DLY 100 usec
Description: >>VLAN pro pripojeni do internetu<<
MAC address f44e.05d0.6c17, MTU 1480
IP address 85.71.188.158, subnet mask 255.255.255.255
Traffic Statistics for "OUTSIDE":
90008 packets input, 10328084 bytes
60609 packets output, 13240078 bytes
1213 packets dropped
1 minute input rate 15 pkts/sec, 994 bytes/sec
[3.]
Jan 13 2015 06:45:30 ASA-FW01 : %ASA-6-106100: access-list OUTSIDE denied tcp OUTSIDE/193.86.236.70(46085) -> OUTSIDE/85.71.188.158(22) hit-cnt 1 first hit [0xb74026ad, 0x0]
[4.]
access-list OUTSIDE remark =======================================================================================
access-list OUTSIDE extended permit icmp any any echo-reply
access-list OUTSIDE extended deny ip any any log
access-group OUTSIDE in interface OUTSIDE
[5.]
Jan 12 2015 23:00:46 ASA-FW01 : %ASA-2-106016: Deny IP spoof from (193.86.236.70) to 85.71.188.158 on interface OUTSIDE
[6.]
Jan 13 2015 06:51:16 ASA-FW01 : %ASA-4-400014: IDS:2004 ICMP echo request from 193.86.236.70 to 85.71.188.158 on interface OUTSIDE
[7.]
icmp unreachable rate-limit 1 burst-size 1
icmp permit 10.0.0.0 255.0.0.0 INSIDE
icmp permit 10.0.0.0 255.0.0.0 EXT-WIFI-VLAN30
icmp permit any OUTSIDEYou're right that the ACL should not affect otherwise allowed communications to the interface address.
Try disabling the ip audit feature on your outside interface.
no ip audit interface OUTSIDE AP_OUTSIDE_INFO
no ip audit interface OUTSIDE AP_OUTSIDE_ATTACK -
Firewall Cisco ASA 5505 new interface license problem
Hi
I have one ASA 5505 with a Base License
The problem is when i want to use a new named interface the system says "With current License maximum number of named interfaces allowed is 3. Name cannot be set for this interface"
And the question is if with this base license the interface cannot be used or only cannot be named?
here the output of my firewall:
Cisco Adaptive Security Appliance Software Version 8.2(5)
Device Manager Version 6.4(5)
Hardware: ASA5505, 512 MB RAM, CPU Geode 500 MHz
Internal ATA Compact Flash, 128MB
BIOS Flash Firmware Hub @ 0xffe00000, 1024KB
Encryption hardware device : Cisco ASA-5505 on-board accelerator (revision 0x0)
Boot microcode : CN1000-MC-BOOT-2.00
SSL/IKE microcode: CNLite-MC-SSLm-PLUS-2.03
IPSec microcode : CNlite-MC-IPSECm-MAIN-2.05
0: Int: Internal-Data0/0 : address is e02f.6de6.7843, irq 11
1: Ext: Ethernet0/0 : address is e02f.6de6.783b, irq 255
2: Ext: Ethernet0/1 : address is e02f.6de6.783c, irq 255
3: Ext: Ethernet0/2 : address is e02f.6de6.783d, irq 255
4: Ext: Ethernet0/3 : address is e02f.6de6.783e, irq 255
5: Ext: Ethernet0/4 : address is e02f.6de6.783f, irq 255
6: Ext: Ethernet0/5 : address is e02f.6de6.7840, irq 255
7: Ext: Ethernet0/6 : address is e02f.6de6.7841, irq 255
8: Ext: Ethernet0/7 : address is e02f.6de6.7842, irq 255
9: Int: Internal-Data0/1 : address is 0000.0003.0002, irq 255
10: Int: Not used : irq 255
11: Int: Not used : irq 255
Licensed features for this platform:
Maximum Physical Interfaces : 8
VLANs : 3, DMZ Restricted
Inside Hosts : Unlimited
Failover : Disabled
VPN-DES : Enabled
VPN-3DES-AES : Enabled
SSL VPN Peers : 2
Total VPN Peers : 10
Dual ISPs : Disabled
VLAN Trunk Ports : 0
Shared License : Disabled
AnyConnect for Mobile : Disabled
AnyConnect for Cisco VPN Phone : Disabled
AnyConnect Essentials : Disabled
Advanced Endpoint Assessment : Disabled
UC Phone Proxy Sessions : 2
Total UC Proxy Sessions : 2
Botnet Traffic Filter : DisabledHi,
The ASA5505 has with Base License the limitation of 3 Vlan interface of which 1 is also limited in access (shown by the above output mentioning DMZ Restricted)
For an interface on the ASA to operate it must have a name with the command "nameif"
If you already have 3 Vlan interfaces in use then with this license you wont be able to configure 4th Vlan interface without getting a license that supports more interfaces. I guess that would be the Security Plus license.
I know that this has come as a surprise to several users that have posted here on the forums. I too think that its a needles "feature" in the ASA to limit the use of the device in such a way.
- Jouni -
Hello, I have been trying to configure a VPN with Cisco Asa 5505 and Cisco VPN client 5.X for 3 weeks and I am not being able to accomplish it, so I decided to reset to factory defaults and start over again.
I used ASDM 6.4 VPN wizard to configure it (I selected exempt local network from NAT and enabled split tunneling, but I have tried other combinations as well).
Tunnel seems to be established properly since I do see an endpoint while using 'sh crypto isakmp sa' but 'sh crypto ipsec sa' shows no packets encrypted or decrypted, so VPN is not working as expected. I can't ping or rdp to internal LAN:
#pkts encaps: 0, #pkts encrypt: 0, #pkts digest: 0
#pkts decaps: 0, #pkts decrypt: 0, #pkts verify: 0
The running-config it created is:
ciscoasa# sh run
: Saved
ASA Version 8.4(2)
hostname ciscoasa
enable password XXXX encrypted
passwd XXXX encrypted
names
interface Ethernet0/0
switchport access vlan 2
interface Ethernet0/1
interface Ethernet0/2
interface Ethernet0/3
interface Ethernet0/4
interface Ethernet0/5
interface Ethernet0/6
interface Ethernet0/7
interface Vlan1
nameif inside
security-level 100
ip address 172.16.1.254 255.255.0.0
interface Vlan2
nameif outside
security-level 0
pppoe client vpdn group ADSL_Telefonica
ip address pppoe setroute
ftp mode passive
object network obj_any
subnet 0.0.0.0 0.0.0.0
object network NETWORK_OBJ_10.0.0.0_24
subnet 10.0.0.0 255.255.255.0
object network NETWORK_OBJ_172.16.0.0_16
subnet 172.16.0.0 255.255.0.0
access-list test_splitTunnelAcl standard permit 172.16.0.0 255.255.0.0
pager lines 24
logging asdm informational
mtu outside 1500
mtu inside 1500
ip local pool test 10.0.0.1-10.0.0.254 mask 255.255.255.0
icmp unreachable rate-limit 1 burst-size 1
no asdm history enable
arp timeout 14400
nat (inside,outside) source static NETWORK_OBJ_172.16.0.0_16 NETWORK_OBJ_172.16.0.0_16 destination static NETWORK_OBJ_10.0.0.0_24 NETWORK_OBJ_10.0.0.0_24 no-proxy-arp route-lookup
object network obj_any
nat (inside,outside) dynamic interface
timeout xlate 3:00:00
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
timeout floating-conn 0:00:00
dynamic-access-policy-record DfltAccessPolicy
aaa authentication ssh console LOCAL
http server enable
http 172.16.0.0 255.255.0.0 inside
no snmp-server location
no snmp-server contact
snmp-server enable traps snmp authentication linkup linkdown coldstart warmstart
crypto ipsec ikev1 transform-set ESP-3DES-SHA esp-3des esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-DES-SHA esp-des esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-DES-MD5 esp-des esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-3DES-MD5 esp-3des esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-AES-256-SHA esp-aes-256 esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-AES-128-SHA esp-aes esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-AES-128-MD5 esp-aes esp-md5-hmac
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set pfs group1
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set ikev1 transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA ESP-3DES-MD5 ESP-DES-SHA ESP-DES-MD5
crypto map outside_map 65535 ipsec-isakmp dynamic SYSTEM_DEFAULT_CRYPTO_MAP
crypto map outside_map interface outside
crypto ikev1 enable outside
crypto ikev1 policy 10
authentication pre-share
encryption 3des
hash sha
group 2
lifetime 86400
telnet 172.16.0.0 255.255.0.0 inside
telnet timeout 55
ssh 172.16.0.0 255.255.0.0 inside
ssh timeout 55
console timeout 0
vpdn group ADSL_Telefonica request dialout pppoe
vpdn group ADSL_Telefonica localname adslppp@telefonicanetpa
vpdn group ADSL_Telefonica ppp authentication pap
vpdn username adslppp@telefonicanetpa password *****
dhcpd auto_config outside
dhcpd address 172.16.2.2-172.16.2.129 inside
dhcpd enable inside
threat-detection basic-threat
threat-detection statistics access-list
no threat-detection statistics tcp-intercept
webvpn
group-policy test internal
group-policy test attributes
dns-server value 172.16.1.1
vpn-tunnel-protocol ikev1
split-tunnel-policy tunnelspecified
split-tunnel-network-list value test_splitTunnelAcl
username test password XXXXXX encrypted privilege 0
username test attributes
vpn-group-policy test
username ignacio password XXXXXXX encrypted
tunnel-group test type remote-access
tunnel-group test general-attributes
address-pool test
default-group-policy test
tunnel-group test ipsec-attributes
ikev1 pre-shared-key *****
class-map inspection_default
match default-inspection-traffic
policy-map type inspect dns preset_dns_map
parameters
message-length maximum client auto
message-length maximum 512
policy-map global_policy
class inspection_default
inspect dns preset_dns_map
inspect ftp
inspect h323 h225
inspect h323 ras
inspect rsh
inspect rtsp
inspect esmtp
inspect sqlnet
inspect skinny
inspect sunrpc
inspect xdmcp
inspect sip
inspect netbios
inspect tftp
inspect ip-options
inspect icmp
service-policy global_policy global
prompt hostname context
no call-home reporting anonymous
Cryptochecksum:c8935bd572dfd37e81c6aa9f9dc8207c
: end
Thank you very much for your helpYes, it was a VPN client problem. I was doing test with a WWAN card and it seems it is not compatible with windows 7.
• The VPN Client on Windows 7 does not support WWAN devices (also called wireless data cards).
I should have read Release Notes before. Thank you very much for your help and effort. -
Cisco ASA 5505 Reset-I Problem with TCP State Bypass
Hello,
I have a Cisco ASA 5505 that functions as my primary firewall and a Mitel 5000 controller behind it. I have two external phone users that have been connecting through the firewall with no issues for six months until about two weeks ago. I am now seeing the following log entry on the phone trying to connect to the Mitel Controller.
6
May 16 2014
14:52:52
302014
72.135.115.37
6915
192.168.20.2
6801
Teardown TCP connection 1203584 for outside:72.135.115.37/6915 to inside:192.168.20.2/6801 duration 0:00:00 bytes 0 TCP Reset-I
My phones are designed to work with the Mitel 5000 and Mitel 3300 phone controllers. The 5000 will only use port 6800 for call control, while the 3300 will use 6801 (Secured Minet), 6802 (Minet SSH), and if those fail, port 6800 (Minet Unsecured). When the phones initiate a connection, they try 6801 first. If 6801 is unavailable, the phone controller adds the RST flag to the ACK packet. When the phone sees the RST flag, it is supposed to reset and use the next port (6802). The same process happens again for port 6802, then the phone knows to try 6800. The problem is that the ASA sees the RST flag now and terminates the connection at the firewall. Therefore, the phones never see the RST flag, and continue to try the connection with port 6801.
I have tried to use the TCP State Bypass feature to correct the situation, but the log shows that the connection is still being terminated immediately by the firewall. I am a novice when it comes to configuring the ASA. Any help would be greatly appreciated, as the company that I bought the phone system from is out of troubleshooting options. I do not think that I have made any changes to the firewall around this time. I have packet captures and logs from my ASA and I have wireshark data on the inside of my network. I need to figure out how to configure the ASA so that it ignores the RST flag and sends the packet back to the source.
Any help would be greatly appreciated!Thanks Rizwan,
Still no luck. I can't even ping the otherside (office).. I am not sure if i'm running the debug rightway. Here are my results...
homeasa(config)# ping inside 10.10.5.254............. (Office CIsco ASA5505 IP on local side. I also tried pinging the server on other side (office) whic is @10.10.5.10 and got the same result)
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 10.10.5.254, timeout is 2 seconds:
Success rate is 0
homeasa(config)# debug crypto isakmp 7
homeasa(config)# debug crypto ipsec 7
homeasa(config)# sho crypto isakmp 7
^
ERROR: % Invalid input detected at '^' marker.
homeasa(config)# sho crypto isakmp
There are no isakmp sas
Global IKE Statistics
Active Tunnels: 0
Previous Tunnels: 0
In Octets: 0
In Packets: 0
In Drop Packets: 0
In Notifys: 0
In P2 Exchanges: 0
In P2 Exchange Invalids: 0
In P2 Exchange Rejects: 0
In P2 Sa Delete Requests: 0
Out Octets: 0
Out Packets: 0
Out Drop Packets: 0
Out Notifys: 0
Out P2 Exchanges: 0
Out P2 Exchange Invalids: 0
Out P2 Exchange Rejects: 0
Out P2 Sa Delete Requests: 0
Initiator Tunnels: 0
Initiator Fails: 0
Responder Fails: 0
System Capacity Fails: 0
Auth Fails: 0
Decrypt Fails: 0
Hash Valid Fails: 0
No Sa Fails: 0
Global IPSec over TCP Statistics
Embryonic connections: 0
Active connections: 0
Previous connections: 0
Inbound packets: 0
Inbound dropped packets: 0
Outbound packets: 0
Outbound dropped packets: 0
RST packets: 0
Recevied ACK heart-beat packets: 0
Bad headers: 0
Bad trailers: 0
Timer failures: 0
Checksum errors: 0
Internal errors: 0
hjnavasa(config)# sh crypto ipsec sa peer 96.xxx.xxx.118
There are no ipsec sas
homeasa(config)# -
Cisco ASA 5505 Password Problem
I recently ran into a telnet, console, and enable password issue that was unexpected and I am hoping someone can explain what happened.
I had two working Cisco ASA 5505's that were two end-points of a Site-to-Site VPN. I had used the ASDM file management tools to copy disk0 startup-config.cfg to a file named old-startup-config.cfg on disk0, on both ASA systems, and I wanted those two files to function as good working startup-config backups that I could return to, right there on the firewall, if I had to. I also used the ASDM file management tools to make configuration "zip" backups to my local computer. I am aware that the actual startup-config file is some type of hidden file.
I had made some changes to both Cisco ASA 5505s, but no password changes, and everything was working great and was reloading great. Then, I suddenly found that I needed to revert back to the old working configurations that I had backed up previously. I used the ASDM file management tools to copy old-startup-config.cfg back to startup-config.cfg on disk0 on both machines. I think I may have also issued the CLI command copy old-startup-config.cfg startup-config. I asked both systems to reload without writing the running-config's to memory.
When the systems reloaded, the console, telnet, and enable passwords were no longer recognized on the CLI and Web interface. The interfaces loaded normally, but the passwords didn't work and the cisco default passwords didn't work either. I had to go to each unit's physical location and perform a power cycle and console password recovery.
I am not sure why that happened. Is the startup-config.cfg file on disk0 an altered version of the actual startup-config configuration with missing or encrypted password credentials? I would have never guessed in a million years that my procedure would have knocked out the enable password.
Instead of copy startup-config.cfg old-startup-config.cfg, should I have issued the command copy startup-config old-startup-config.cfg to make a local backup of a working configuration?
I have one more semi-related question. If one uses ASDM file management to create a zip backup of a startup-config or running-config and then proceeds to restore a running-config, when does the restored running-config take effect?If password recovery is disabled then you are locked out hard. You have to sacrifice the config to "re-admin" the appliance. Sorry for the bad news but that's the way it is by design. If there was a "back door" it would hardly be a security appliance would it?
-
Cisco ASA 5505 Site to Site VPN Problem
Hi All,
We have a site to site VPN with a cisco asa 5505 on one end and a Checkpoint firewall on the other end.
We can establish the vpn tunnel and all users in the remote office are working great. However at a random point during the day or it may even be after 2 weeks of working, the tunnel between the sites automatically fails.
When I dial into the modem which is connected to the firewall I see the following messages in the logs:
Sep 14 2011 16:40:02: %ASA-3-713902: Group = *.*.*.*, IP = *.*.*.*, QM FSM error (P2 struct &0x42314d8, mess id 0xa18dcb12)!
Sep 14 2011 16:40:02: %ASA-1-713900: Group = *.*.*.*, IP = *.*.*.*, construct_ipsec_delete(): No SPI to identify Phase 2 SA!
Sep 14 2011 16:40:02: %ASA-3-713902: Group = *.*.*.*, IP = *.*.*.*, Removing peer from correlator table failed, no match!
Sep 14 2011 16:40:14: %ASA-3-713902: Group = *.*.*.*, IP = *.*.*.*, QM FSM error (P2 struct &0x426b988, mess id 0xf0160f94)!
Sep 14 2011 16:40:14: %ASA-1-713900: Group = *.*.*.*, IP = *.*.*.*, construct_ipsec_delete(): No SPI to identify Phase 2 SA!
Sep 14 2011 16:40:14: %ASA-3-713902: Group = *.*.*.*, IP = *.*.*.*, Removing peer from correlator table failed, no match!
Sep 14 2011 16:40:02: %ASA-3-713902: Group = *.*.*.*, IP = *.*.*.*, QM FSM error (P2 struct &0x42314d8, mess id 0xa18dcb12)!
Sep 14 2011 16:40:02: %ASA-1-713900: Group = *.*.*.*, IP = *.*.*.*, construct_ipsec_delete(): No SPI to identify Phase 2 SA!
Sep 14 2011 16:40:02: %ASA-3-713902: Group = *.*.*.*, IP = *.*.*.*, Removing peer from correlator table failed, no match!
Sep 14 2011 16:40:14: %ASA-3-713902: Group = *.*.*.*, IP = *.*.*.*, QM FSM error (P2 struct &0x426b988, mess id 0xf0160f94)!
Sep 14 2011 16:40:14: %ASA-1-713900: Group = *.*.*.*, IP = *.*.*.*, construct_ipsec_delete(): No SPI to identify Phase 2 SA!
Sep 14 2011 16:40:14: %ASA-3-713902: Group = *.*.*.*, IP = *.*.*.*, Removing peer from correlator table failed, no match!
There is nothing in the Checkpoint logs. To solve the issue I have to reload the firewall.
I have checked both firewalls for any mis-matched parameters and do not see any.
Any help is very much appreciated as it is very frustrating for myself and the users in the remote office.
Thanks!Also to note, PFS is enabled on both firewalls. Config on Cisco ASA firewall as follows:
hostname
domain-name
enable passwordpasswd names
interface Vlan701
nameif inside
security-level 100
ip address 10.65.0.69 255.255.255.252
interface Vlan999
nameif outside
security-level 0
ip address ****** 255.255.255.248
interface Ethernet0/0
description Link to Internet
switchport access vlan 999
interface Ethernet0/1
description
switchport access vlan 701
interface range Ethernet0/2 - 0/7
switchport access vlan 2
shutdown
ftp mode passive
dns server-group DefaultDNS
domain-name******
access-list 101 extended permit ip host ****** 172.25.0.0 255.255.0.0
access-list 101 extended permit ip 10.65.0.64 255.255.255.192 172.25.0.0 255.255.0.0
access-list 101 extended permit ip 10.65.0.64 255.255.255.192 172.28.0.0 255.255.0.0
access-list 101 extended permit ip 10.65.0.64 255.255.255.192 172.26.0.0 255.255.0.0
access-list 101 extended permit ip 10.65.0.64 255.255.255.192 172.16.0.0 255.248.0.0
access-list 101 extended permit ip 10.65.0.64 255.255.255.192 10.72.0.0 255.255.0.0
access-list 101 extended permit ip 10.65.0.64 255.255.255.224 10.68.2.0 255.255.255.0
access-list 101 extended permit ip 10.65.0.64 255.255.255.192 10.151.10.0 255.255.255.0
access-list 101 extended permit ip 10.65.0.64 255.255.255.192 host ******
access-list 101 extended permit ip 10.65.0.64 255.255.255.192 ******* 255.255.255.0
access-list nonat extended permit ip 10.65.0.64 255.255.255.192 172.25.0.0 255.255.0.0
access-list nonat extended permit ip 10.65.0.64 255.255.255.192 172.28.0.0 255.255.0.0
access-list nonat extended permit ip 10.65.0.64 255.255.255.192 172.26.0.0 255.255.0.0
access-list nonat extended permit ip 10.65.0.64 255.255.255.192 172.16.0.0 255.248.0.0
access-list nonat extended permit ip 10.65.0.64 255.255.255.192 10.72.0.0 255.255.0.0
access-list nonat extended permit ip 10.65.0.64 255.255.255.224 10.68.2.0 255.255.255.0
access-list nonat extended permit ip 10.65.0.64 255.255.255.192 10.151.10.0 255.255.255.0
access-list nonat extended permit ip 10.65.0.64 255.255.255.192 ******** 255.255.255.0
pager lines 24
logging enable
logging timestamp
logging buffered warnings
logging trap warnings
logging asdm informational
logging host outside *****
mtu inside 1500
mtu outside 1500
no failover
icmp unreachable rate-limit 1 burst-size 1
asdm history enable
arp timeout 14400
nat (inside) 0 access-list nonat
route inside ******
route outside 0.0.0.0 0.0.0.0 ********
timeout xlate 0:05:00
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
aaa-server TACACS+ protocol tacacs+
aaa-server RADIUS protocol radius
aaa authentication ssh console LOCAL
aaa authentication telnet console LOCAL
snmp-server location **:
snmp-server contact **
snmp-server community shortkey
snmp-server enable traps snmp authentication linkup linkdown coldstart
snmp-server enable traps syslog
crypto ipsec transform-set 3desmd5 esp-3des esp-md5-hmac
crypto map CASGMAP 50 match address 101
crypto map CASGMAP 50 set pfs group1
crypto map CASGMAP 50 set peer ********
crypto map CASGMAP 50 set transform-set 3desmd5
crypto map CASGMAP 50 set security-association lifetime seconds 3600
crypto map CASGMAP interface outside
crypto isakmp enable outside
crypto isakmp policy 20
authentication pre-share
encryption 3des
hash md5
group 2
lifetime 86400
telnet **** inside
telnet timeout 5
ssh **** inside
ssh **** outside
ssh timeout 5
console timeout 30
management-access inside
dhcpd ping_timeout 750
priority-queue outside
ntp server **
username ***
tunnel-group ******** type ipsec-l2l
tunnel-group ******** ipsec-attributes
pre-shared-key ***
class-map VoIP
match dscp ef
class-map inspection_default
match default-inspection-traffic
policy-map type inspect dns preset_dns_map
parameters
message-length maximum 512
policy-map General-purpose
class VoIP
priority
policy-map global_policy
class inspection_default
inspect dns preset_dns_map
inspect ftp
inspect h323 h225
inspect h323 ras
inspect netbios
inspect rsh
inspect rtsp
inspect skinny
inspect esmtp
inspect sqlnet
inspect sunrpc
inspect tftp
inspect sip
inspect xdmcp
inspect http
service-policy General-purpose interface outside
prompt hostname context -
CISCO ASA 5505 VPN problem in Windows 7
I am using CISCO ASA 5505. Client PC with Windows XP can use IE to make the VPN connection normally.
However, client PC with Windows 7 cannot use IE to make the VPN connection.
It just show the error of "Internet Explorer cannot display the webpage"
Would you please help?
Thank you very much!Hi Timothy,
Could you please try disabling UAC in Win 7. Also try to connect from a machine where you have admin privileges (in case you are trying connection from a restricted machine.
Also, add the site under trusted sites in IE. i.e if you are connecting to https://1.1.1.1 or https://vpn.abc.com then please add it under the trusted sites:
Let me know if this helps.
Thanks,
Vishnu Sharma -
Cisco ASA 5505 - 2 PPPoE connection
Hi,
Please I would be very pleased if someone could give me a hand in this matter.
I have a Cisco ASA 5505 9.0(2), 2 dial-up connection (ADSL) with fix IP from the same ISP. I have 2 Linksys router (each dial-up has a router) as well. Both Linksys are connected directly to ASA configured in bridge mode.
I set up one dial-up on interface called “outside” with PPPoE configuration which is, in fact, up and running. I’m able to get my fix public IP.
My problem come from when I try to set up the second dial-up on interface called “outside-other”. I configure properly all PPPoE parameters however I’m not able to get my second fix public IP. Somehow, it’s not able to establish a connection with the ISP. (PPPoE session has not been established yet)
This could be useful information: the PPPoE Username is the same in both dial-up connection (given by my ISP).
I hope someone can shed light on this issue.
Thanks in advance,
Apologies for my lack of awareness.
AntonioHi,
This is my schema:
connection A ( interface outside) --> DSL --> Router Linksys mode bridge --> Cisco ASA , up and running with IP fix.
connection B ( interface outside-other) --> DSL --> Router Linksys mode bridge --> Cisco ASA, down : Status PADR_SENT
I tried to use two different VPDN_groups for the two connections A and B. However, B is still not working. Just one of them is able to get IP from ISP, connection A.
When I set up the Linksys router (connection B) in PPPoE, the connection works and get an IP fix from ISP.
What I want to do is set up a VPN on connection B so I need to configure this second dial-up on Cisco ASA. I cannot use connection A due to security reasons.
Thanks -
Internet Connection Became Slow after Introduction of Cisco ASA 5505 to the Network
I configured a Cisco ASA 5505 (Version Cisco Adaptive Security Appliance Software Version 7.2(3)
Device Manager Version 5.2(3)
in transparent firewall mode and inserted after Cisco 1700 router. However, the internet connection became very slow and users are compaining that they cannot load any pages.
My setup looks like:
Internet --> Cisco 1700 --> Cisco ASA 5505 --> LAN
The license information is:
Licensed features for this platform:
Maximum Physical Interfaces : 8
VLANs : 3, DMZ Restricted
Inside Hosts : Unlimited
Failover : Disabled
VPN-DES : Enabled
VPN-3DES-AES : Enabled
VPN Peers : 10
WebVPN Peers : 2
Dual ISPs : Disabled
VLAN Trunk Ports : 0
This platform has a Base license.
The flash activation key is the SAME as the running key.
My running-config looks like:
ASA Version 7.2(3)
firewall transparent
hostname ciscoasa
domain-name default.domain.invalid
enable password 8Ry2YjIyt7RRXU24 encrypted
names
interface Vlan1
nameif inside
security-level 100
no shut
interface Vlan2
nameif outside
security-level 0
no shut
interface Ethernet0/0
switchport access vlan 2
no shut
interface Ethernet0/1
no shut
interface Ethernet0/2
no shut
interface Ethernet0/3
no shut
interface Ethernet0/4
no shut
interface Ethernet0/5
no shut
interface Ethernet0/6
no shut
interface Ethernet0/7
no shut
passwd 2KFQnbNIdI.2KYOU encrypted
regex urllist1 ".*\.([Ee][Xx][Ee]|[Cc][Oo][Mm]|[Bb][Aa][Tt]) HTTP/1.[01]"
regex urllist2 ".*\.([Pp][Ii][Ff]|[Vv][Bb][Ss]|[Ww][Ss][Hh]) HTTP/1.[01]"
regex urllist3 ".*\.([Dd][Oo][Cc]|[Xx][Ll][Ss]|[Pp][Pp][Tt]) HTTP/1.[01]"
regex urllist4 ".*\.([Zz][Ii][Pp]|[Tt][Aa][Rr]|[Tt][Gg][Zz]) HTTP/1.[01]"
regex domainlist1 "\.facebook\.com"
regex domainlist2 "\.diretube\.com"
regex domainlist3 "\.youtube\.com"
regex domainlist4 "\.vimeo\.com"
regex applicationheader "application/.*"
regex contenttype "Content-Type"
ftp mode passive
dns server-group DefaultDNS
domain-name default.domain.invalid
access-list outside_in extended permit ip any any
access-list inside_mpc extended permit tcp any any eq www
access-list inside_mpc extended permit tcp any any eq 8080
pager lines 24
mtu outside 1500
mtu inside 1500
ip address 192.168.1.254 255.255.255.0
icmp unreachable rate-limit 1 burst-size 1
no asdm history enable
arp timeout 14400
access-group outside_in in interface outside
route outside 0.0.0.0 0.0.0.0 192.168.1.1 1
timeout xlate 3:00:00
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout uauth 0:05:00 absolute
no snmp-server location
no snmp-server contact
snmp-server enable traps snmp authentication linkup linkdown coldstart
telnet timeout 5
ssh timeout 5
console timeout 0
class-map type regex match-any DomainBlockList
match regex domainlist1
match regex domainlist2
match regex domainlist3
match regex domainlist4
class-map type inspect http match-all BlockDomainsClass
match request header host regex class DomainBlockList
class-map type regex match-any URLBlockList
match regex urllist1
match regex urllist2
match regex urllist3
match regex urllist4
class-map inspection_default
match default-inspection-traffic
class-map type inspect http match-all AppHeaderClass
match response header regex contenttype regex applicationheader
class-map httptraffic
match access-list inside_mpc
class-map type inspect http match-all BlockURLsClass
match request uri regex class URLBlockList
policy-map type inspect dns preset_dns_map
parameters
message-length maximum 512
policy-map type inspect http http_inspection_policy
parameters
protocol-violation action drop-connection
class AppHeaderClass
drop-connection log
match request method connect
drop-connection log
class BlockDomainsClass
reset log
class BlockURLsClass
reset log
policy-map global_policy
class inspection_default
inspect dns preset_dns_map
inspect ftp
inspect h323 h225
inspect h323 ras
inspect netbios
inspect rsh
inspect rtsp
inspect skinny
inspect esmtp
inspect sqlnet
inspect sunrpc
inspect tftp
inspect sip
inspect xdmcp
policy-map inside-policy
class httptraffic
inspect http http_inspection_policy
service-policy global_policy global
service-policy inside-policy interface inside
prompt hostname context
Cryptochecksum:8ab1a53df6ae3c202aee236d6080edfd
: end
Could the slow internet connection be due to license limitations? Or is there something wrong with my configuration?
Please see the configuration and help.
ThanksI have re-configured the ASA 5505 yesterday and so far it's working fine. I am not sure if the problem will re-appear later on. Anyways here is my sh tech-support
ciscoasa# sh tech-support
Cisco Adaptive Security Appliance Software Version 7.2(3)
Device Manager Version 5.2(3)
Compiled on Wed 15-Aug-07 16:08 by builders
System image file is "disk0:/asa723-k8.bin"
Config file at boot was "startup-config"
ciscoasa up 14 hours 16 mins
Hardware: ASA5505, 256 MB RAM, CPU Geode 500 MHz
Internal ATA Compact Flash, 128MB
BIOS Flash M50FW080 @ 0xffe00000, 1024KB
Encryption hardware device : Cisco ASA-5505 on-board accelerator (revision 0x0)
Boot microcode : CNlite-MC-Boot-Cisco-1.2
SSL/IKE microcode: CNlite-MC-IPSEC-Admin-3.03
IPSec microcode : CNlite-MC-IPSECm-MAIN-2.04
0: Int: Internal-Data0/0 : address is 001f.9ee8.ffa2, irq 11
1: Ext: Ethernet0/0 : address is 001f.9ee8.ff9a, irq 255
2: Ext: Ethernet0/1 : address is 001f.9ee8.ff9b, irq 255
3: Ext: Ethernet0/2 : address is 001f.9ee8.ff9c, irq 255
4: Ext: Ethernet0/3 : address is 001f.9ee8.ff9d, irq 255
5: Ext: Ethernet0/4 : address is 001f.9ee8.ff9e, irq 255
6: Ext: Ethernet0/5 : address is 001f.9ee8.ff9f, irq 255
<--- More --->
7: Ext: Ethernet0/6 : address is 001f.9ee8.ffa0, irq 255
8: Ext: Ethernet0/7 : address is 001f.9ee8.ffa1, irq 255
9: Int: Internal-Data0/1 : address is 0000.0003.0002, irq 255
10: Int: Not used : irq 255
11: Int: Not used : irq 255
Licensed features for this platform:
Maximum Physical Interfaces : 8
VLANs : 3, DMZ Restricted
Inside Hosts : Unlimited
Failover : Disabled
VPN-DES : Enabled
VPN-3DES-AES : Enabled
VPN Peers : 10
WebVPN Peers : 2
Dual ISPs : Disabled
VLAN Trunk Ports : 0
This platform has a Base license.
Serial Number: JMX1211Z2N4
Running Activation Key: 0xaf0ed046 0xbcf18ebf 0x80b38508 0xba785cc0 0x05250493
Configuration register is 0x1
Configuration has not been modified since last system restart.
<--- More --->
------------------ show clock ------------------
18:32:58.254 UTC Tue Nov 26 2013
------------------ show memory ------------------
Free memory: 199837144 bytes (74%)
Used memory: 68598312 bytes (26%)
Total memory: 268435456 bytes (100%)
------------------ show conn count ------------------
1041 in use, 2469 most used
------------------ show xlate count ------------------
0 in use, 0 most used
------------------ show blocks ------------------
SIZE MAX LOW CNT
0 100 68 100
<--- More --->
4 300 299 299
80 100 92 100
256 100 94 100
1550 6174 6166 6174
2048 1124 551 612
------------------ show blocks queue history detail ------------------
History buffer memory usage: 2136 bytes (default)
------------------ show interface ------------------
Interface Internal-Data0/0 "", is up, line protocol is up
Hardware is y88acs06, BW 1000 Mbps
(Full-duplex), (1000 Mbps)
MAC address 001f.9ee8.ffa2, MTU not set
IP address unassigned
18491855 packets input, 11769262614 bytes, 0 no buffer
Received 213772 broadcasts, 0 runts, 0 giants
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
0 L2 decode drops, 0 demux drops
18185861 packets output, 11626494317 bytes, 0 underruns
0 output errors, 0 collisions, 0 interface resets
0 late collisions, 0 deferred
<--- More --->
0 input reset drops, 0 output reset drops
input queue (curr/max packets): hardware (0/0) software (0/0)
output queue (curr/max packets): hardware (0/55) software (0/0)
Control Point Interface States:
Interface number is unassigned
Interface Internal-Data0/1 "", is administratively down, line protocol is up
Hardware is 88E6095, BW 1000 Mbps
(Full-duplex), (1000 Mbps)
MAC address 0000.0003.0002, MTU not set
IP address unassigned
18184216 packets input, 11625360131 bytes, 0 no buffer
Received 206655 broadcasts, 0 runts, 0 giants
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
0 switch ingress policy drops
18490057 packets output, 11768078777 bytes, 0 underruns
0 output errors, 0 collisions, 0 interface resets
0 babbles, 0 late collisions, 0 deferred
0 lost carrier, 0 no carrier
0 switch egress policy drops
Control Point Interface States:
Interface number is unassigned
Interface Loopback0 "_internal_loopback", is up, line protocol is up
Hardware is VirtualMAC address 0000.0000.0000, MTU 1500
IP address 127.1.0.1, subnet mask 255.255.0.0
<--- More --->
Traffic Statistics for "_internal_loopback":
1 packets input, 28 bytes
1 packets output, 28 bytes
1 packets dropped
1 minute input rate 0 pkts/sec, 0 bytes/sec
1 minute output rate 0 pkts/sec, 0 bytes/sec
1 minute drop rate, 0 pkts/sec
5 minute input rate 0 pkts/sec, 0 bytes/sec
5 minute output rate 0 pkts/sec, 0 bytes/sec
5 minute drop rate, 0 pkts/sec
Control Point Interface States:
Interface number is 28
Interface config status is active
Interface state is active
Interface Vlan1 "inside", is up, line protocol is up
Hardware is EtherSVI
MAC address 001f.9ee8.ffa2, MTU 1500
IP address 192.168.1.254, subnet mask 255.255.255.0
Traffic Statistics for "inside":
7742275 packets input, 903584114 bytes
10645034 packets output, 10347291114 bytes
184883 packets dropped
1 minute input rate 320 pkts/sec, 35404 bytes/sec
1 minute output rate 325 pkts/sec, 313317 bytes/sec
<--- More --->
1 minute drop rate, 17 pkts/sec
5 minute input rate 399 pkts/sec, 59676 bytes/sec
5 minute output rate 483 pkts/sec, 503200 bytes/sec
5 minute drop rate, 9 pkts/sec
Control Point Interface States:
Interface number is 1
Interface config status is active
Interface state is active
Interface Vlan2 "outside", is up, line protocol is up
Hardware is EtherSVI
MAC address 001f.9ee8.ffa3, MTU 1500
IP address 192.168.1.254, subnet mask 255.255.255.0
Traffic Statistics for "outside":
10750090 packets input, 10432619059 bytes
7541331 packets output, 870613684 bytes
109911 packets dropped
1 minute input rate 328 pkts/sec, 313770 bytes/sec
1 minute output rate 301 pkts/sec, 32459 bytes/sec
1 minute drop rate, 2 pkts/sec
5 minute input rate 485 pkts/sec, 503789 bytes/sec
5 minute output rate 387 pkts/sec, 57681 bytes/sec
5 minute drop rate, 2 pkts/sec
Control Point Interface States:
Interface number is 2
<--- More --->
Interface config status is active
Interface state is active
Interface Ethernet0/0 "", is up, line protocol is up
Hardware is 88E6095, BW 100 Mbps
Auto-Duplex(Full-duplex), Auto-Speed(100 Mbps)
Available but not configured via nameif
MAC address 001f.9ee8.ff9a, MTU not set
IP address unassigned
10749794 packets input, 10630700889 bytes, 0 no buffer
Received 2506 broadcasts, 0 runts, 0 giants
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
0 L2 decode drops
3 switch ingress policy drops
7541070 packets output, 1028190148 bytes, 0 underruns
0 output errors, 0 collisions, 0 interface resets
0 babbles, 0 late collisions, 0 deferred
0 lost carrier, 0 no carrier
0 rate limit drops
0 switch egress policy drops
Control Point Interface States:
Interface number is unassigned
Interface Ethernet0/1 "", is up, line protocol is up
Hardware is 88E6095, BW 100 Mbps
Auto-Duplex(Full-duplex), Auto-Speed(100 Mbps)
<--- More --->
Available but not configured via nameif
MAC address 001f.9ee8.ff9b, MTU not set
IP address unassigned
7741977 packets input, 1064586806 bytes, 0 no buffer
Received 211282 broadcasts, 0 runts, 0 giants
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
0 L2 decode drops
0 switch ingress policy drops
10644663 packets output, 10543362751 bytes, 0 underruns
0 output errors, 0 collisions, 0 interface resets
0 babbles, 0 late collisions, 0 deferred
0 lost carrier, 0 no carrier
0 rate limit drops
0 switch egress policy drops
Control Point Interface States:
Interface number is unassigned
Interface Ethernet0/2 "", is down, line protocol is down
Hardware is 88E6095, BW 100 Mbps
Auto-Duplex, Auto-Speed
Available but not configured via nameif
MAC address 001f.9ee8.ff9c, MTU not set
IP address unassigned
0 packets input, 0 bytes, 0 no buffer
Received 0 broadcasts, 0 runts, 0 giants
<--- More --->
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
0 L2 decode drops
0 switch ingress policy drops
0 packets output, 0 bytes, 0 underruns
0 output errors, 0 collisions, 0 interface resets
0 babbles, 0 late collisions, 0 deferred
0 lost carrier, 0 no carrier
0 rate limit drops
0 switch egress policy drops
Control Point Interface States:
Interface number is unassigned
Interface Ethernet0/3 "", is down, line protocol is down
Hardware is 88E6095, BW 100 Mbps
Auto-Duplex, Auto-Speed
Available but not configured via nameif
MAC address 001f.9ee8.ff9d, MTU not set
IP address unassigned
0 packets input, 0 bytes, 0 no buffer
Received 0 broadcasts, 0 runts, 0 giants
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
0 L2 decode drops
0 switch ingress policy drops
0 packets output, 0 bytes, 0 underruns
0 output errors, 0 collisions, 0 interface resets
<--- More --->
0 babbles, 0 late collisions, 0 deferred
0 lost carrier, 0 no carrier
0 rate limit drops
0 switch egress policy drops
Control Point Interface States:
Interface number is unassigned
Interface Ethernet0/4 "", is down, line protocol is down
Hardware is 88E6095, BW 100 Mbps
Auto-Duplex, Auto-Speed
Available but not configured via nameif
MAC address 001f.9ee8.ff9e, MTU not set
IP address unassigned
0 packets input, 0 bytes, 0 no buffer
Received 0 broadcasts, 0 runts, 0 giants
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
0 L2 decode drops
0 switch ingress policy drops
0 packets output, 0 bytes, 0 underruns
0 output errors, 0 collisions, 0 interface resets
0 babbles, 0 late collisions, 0 deferred
0 lost carrier, 0 no carrier
0 rate limit drops
0 switch egress policy drops
Control Point Interface States:
<--- More --->
Interface number is unassigned
Interface Ethernet0/5 "", is down, line protocol is down
Hardware is 88E6095, BW 100 Mbps
Auto-Duplex, Auto-Speed
Available but not configured via nameif
MAC address 001f.9ee8.ff9f, MTU not set
IP address unassigned
0 packets input, 0 bytes, 0 no buffer
Received 0 broadcasts, 0 runts, 0 giants
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
0 L2 decode drops
0 switch ingress policy drops
0 packets output, 0 bytes, 0 underruns
0 output errors, 0 collisions, 0 interface resets
0 babbles, 0 late collisions, 0 deferred
0 lost carrier, 0 no carrier
0 rate limit drops
0 switch egress policy drops
Control Point Interface States:
Interface number is unassigned
Interface Ethernet0/6 "", is down, line protocol is down
Hardware is 88E6095, BW 100 Mbps
Auto-Duplex, Auto-Speed
Available but not configured via nameif
<--- More --->
MAC address 001f.9ee8.ffa0, MTU not set
IP address unassigned
0 packets input, 0 bytes, 0 no buffer
Received 0 broadcasts, 0 runts, 0 giants
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
0 L2 decode drops
0 switch ingress policy drops
0 packets output, 0 bytes, 0 underruns
0 output errors, 0 collisions, 0 interface resets
0 babbles, 0 late collisions, 0 deferred
0 lost carrier, 0 no carrier
0 rate limit drops
0 switch egress policy drops
Control Point Interface States:
Interface number is unassigned
Interface Ethernet0/7 "", is down, line protocol is down
Hardware is 88E6095, BW 100 Mbps
Auto-Duplex, Auto-Speed
Available but not configured via nameif
MAC address 001f.9ee8.ffa1, MTU not set
IP address unassigned
0 packets input, 0 bytes, 0 no buffer
Received 0 broadcasts, 0 runts, 0 giants
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
<--- More --->
0 L2 decode drops
0 switch ingress policy drops
0 packets output, 0 bytes, 0 underruns
0 output errors, 0 collisions, 0 interface resets
0 babbles, 0 late collisions, 0 deferred
0 lost carrier, 0 no carrier
0 rate limit drops
0 switch egress policy drops
Control Point Interface States:
Interface number is unassigned
------------------ show cpu usage ------------------
CPU utilization for 5 seconds = 12%; 1 minute: 11%; 5 minutes: 11%
------------------ show cpu hogging process ------------------
Process: Dispatch Unit, NUMHOG: 1, MAXHOG: 133, LASTHOG: 140
LASTHOG At: 04:45:59 UTC Nov 26 2013
PC: 8be0f7
Traceback: 8bed19 8bf553 302b87 3030a5 2fad69 7674bf 75ca16
c6251d c62a4c c62f6c 75c653 767820 797f64 769c85
<--- More --->
------------------ show process ------------------
PC SP STATE Runtime SBASE Stack Process
Mwe 00c9bb24 01bb8700 013e3250 0 01733fc8 15616/16384 emweb/cifs
Lwe 001072ac 0176f9c4 013e32d0 0 0176d9f0 8132/8192 block_diag
Mrd 00223a67 01783d5c 013e33b0 314854 0177be18 25752/32768 Dispatch Unit
Msi 00f82847 01b07b84 013e3250 229 01b05bc0 7984/8192 y88acs06 OneSec Thread
Mwe 0011b1a5 01b09cfc 013e3250 0 01b07d88 7864/8192 Reload Control Thread
Mwe 00120606 01b1260c 013e5258 0 01b10988 7256/8192 aaa
Mwe 001486aa 01b19404 013e5ae8 0 01b15450 16020/16384 CMGR Server Process
Mwe 0014c3c5 01b1b4d4 013e3250 0 01b19570 7968/8192 CMGR Timer Process
Lwe 002227a1 01b239b4 013ee360 0 01b219f0 7524/8192 dbgtrace
Mwe 004e1ba5 01b29c34 013e3250 157 01b27d50 6436/8192 eswilp_svi_init
Mwe 01064b1d 01b4a7f4 013e3250 0 01b48890 7848/8192 Chunk Manager
Msi 008b61b6 01b52d54 013e3250 230 01b50da0 7856/8192 PIX Garbage Collector
Lsi 00ecb6ac 01b54e94 013e3250 12 01b52ec0 7552/8192 route_process
Mwe 008a5ddc 01b5dc04 0133b430 0 01b5bc40 8116/8192 IP Address Assign
Mwe 00acb779 01b60604 01346e10 0 01b5e640 8116/8192 QoS Support Module
Mwe 0091eba9 01b6275c 0133c530 0 01b60798 8116/8192 Client Update Task
Lwe 01083c8e 01b656d4 013e3250 123088 01b63770 7840/8192 Checkheaps
Mwe 00acfd7d 01b6b824 013e3250 623 01b69ad0 3476/8192 Quack process
Mwe 00b2a260 01b6dad4 013e3250 22 01b6bbf0 7364/8192 Session Manager
Mwe 00c55efd 01b78564 031d0478 4 01b74a50 14768/16384 uauth
<--- More --->
Mwe 00be3c9e 01b7aaec 0135c010 0 01b78b28 7524/8192 Uauth_Proxy
Mwe 00c52759 01b80e0c 01361770 0 01b7ee88 7712/8192 SMTP
Mwe 00c3f7b9 01b82eec 01361710 0 01b80fa8 7412/8192 Logger
Mwe 00c3fd26 01b8502c 013e3250 0 01b830c8 7492/8192 Thread Logger
Mwe 00f62272 01b9596c 013ac520 0 01b939c8 7188/8192 vpnlb_thread
Msi 00b4097c 01c598c4 013e3250 190 01c578f0 8000/8192 emweb/cifs_timer
Msi 005bd338 017a909c 013e3250 25855 017a7108 7412/8192 arp_timer
Mwe 005c76bc 01b486e4 013fba50 20643 01b46770 7348/8192 arp_forward_thread
Mwe 00c5a919 023fa5fc 013619e0 0 023f8648 7968/8192 tcp_fast
Mwe 00c5a6e5 023fc624 013619e0 0 023fa670 7968/8192 tcp_slow
Mwe 00c754d1 0240d42c 013628a0 0 0240b478 8100/8192 udp_timer
Mwe 0019cb17 01b404a4 013e3250 0 01b3e530 7984/8192 CTCP Timer process
Mwe 00efe8b3 0308c15c 013e3250 0 0308a208 7952/8192 L2TP data daemon
Mwe 00efef23 0308e194 013e3250 0 0308c230 7968/8192 L2TP mgmt daemon
Mwe 00eea02b 030c62ac 013a5c10 43 030c2338 16244/16384 ppp_timer_thread
Msi 00f62d57 030c82f4 013e3250 264 030c6360 7924/8192 vpnlb_timer_thread
Mwe 001b96e6 01b7cbbc 01b1e9c8 1 01b7ac48 7728/8192 IPsec message handler
Msi 001c9bac 01b8d4dc 013e3250 2917 01b8b548 7648/8192 CTM message handler
Mwe 00af93b8 031465b4 013e3250 0 03144640 7984/8192 ICMP event handler
Mwe 00831003 0314a724 013e3250 387 031467b0 16100/16384 IP Background
Mwe 0021b267 031a83c4 013123c0 31 03188450 123488/131072 tmatch compile thread
Mwe 009f2405 03290044 013e3250 0 0328c0c0 16072/16384 Crypto PKI RECV
Mwe 009f305a 03294144 013e3250 0 032901e0 16040/16384 Crypto CA
Mwe 0064d4fd 01b3e24c 013e3250 8 01b3c2f8 7508/8192 ESW_MRVL switch interrupt service
<--- More --->
Msi 00646f5c 032c134c 013e3250 3059378 032bf448 7184/8192 esw_stats
Lsi 008cbb80 032dc704 013e3250 3 032da730 7908/8192 uauth_urlb clean
Lwe 008afee7 034a0914 013e3250 197 0349e9b0 6636/8192 pm_timer_thread
Mwe 0052f0bf 034a35ac 013e3250 0 034a1648 7968/8192 IKE Timekeeper
Mwe 00520f6b 034a8adc 0132e2b0 0 034a4e38 15448/16384 IKE Daemon
Mwe 00bf5c78 034ac7ac 01360680 0 034aa7f8 8100/8192 RADIUS Proxy Event Daemon
Mwe 00bc32de 034ae79c 034dcbe0 0 034ac918 7208/8192 RADIUS Proxy Listener
Mwe 00bf5e0f 034b099c 013e3250 0 034aea38 7968/8192 RADIUS Proxy Time Keeper
Mwe 005aac4c 034b3154 013fb980 0 034b1250 7492/8192 Integrity FW Task
M* 008550a5 0009fefc 013e33b0 3183 034e3b20 24896/32768 ci/console
Msi 008eb694 034ed9d4 013e3250 2370 034ebc40 6176/8192 update_cpu_usage
Msi 008e6415 034f7dac 013e3250 1096 034f5eb8 6124/8192 NIC status poll
Mwe 005b63e6 03517d1c 013fbd10 1963 03515d78 7636/8192 IP Thread
Mwe 005becbe 03519e4c 013fbcb0 3 03517e98 7384/8192 ARP Thread
Mwe 004c2b36 0351befc 013fbae0 0 03519fe8 7864/8192 icmp_thread
Mwe 00c7722e 0351e06c 013e3250 0 0351c108 7848/8192 udp_thread
Mwe 00c5d126 0352008c 013fbd00 0 0351e228 7688/8192 tcp_thread
Mwe 00bc32de 03a6982c 03a5ee18 0 03a679b8 7512/8192 EAPoUDP-sock
Mwe 00266c15 03a6b614 013e3250 0 03a699e0 7032/8192 EAPoUDP
Mwe 005a6728 01b27b94 013e3250 0 01b25c30 7968/8192 Integrity Fw Timer Thread
- - - - 47686621 - - scheduler
- - - - 51253819 - - total elapsed
------------------ show failover ------------------
<--- More --->
ERROR: Command requires failover license
------------------ show traffic ------------------
inside:
received (in 51429.740 secs):
7749585 packets905087345 bytes
67 pkts/sec17013 bytes/sec
transmitted (in 51429.740 secs):
10653162 packets10355908020 bytes
40 pkts/sec201026 bytes/sec
1 minute input rate 412 pkts/sec, 51803 bytes/sec
1 minute output rate 475 pkts/sec, 522952 bytes/sec
1 minute drop rate, 24 pkts/sec
5 minute input rate 399 pkts/sec, 59676 bytes/sec
5 minute output rate 483 pkts/sec, 503200 bytes/sec
5 minute drop rate, 9 pkts/sec
outside:
received (in 51430.240 secs):
10758403 packets10441440193 bytes
42 pkts/sec203021 bytes/sec
transmitted (in 51430.240 secs):
7548339 packets872053854 bytes
<--- More --->
63 pkts/sec16037 bytes/sec
1 minute input rate 479 pkts/sec, 523680 bytes/sec
1 minute output rate 387 pkts/sec, 46796 bytes/sec
1 minute drop rate, 3 pkts/sec
5 minute input rate 485 pkts/sec, 503789 bytes/sec
5 minute output rate 387 pkts/sec, 57681 bytes/sec
5 minute drop rate, 2 pkts/sec
_internal_loopback:
received (in 51430.740 secs):
1 packets28 bytes
0 pkts/sec0 bytes/sec
transmitted (in 51430.740 secs):
1 packets28 bytes
0 pkts/sec0 bytes/sec
1 minute input rate 0 pkts/sec, 0 bytes/sec
1 minute output rate 0 pkts/sec, 0 bytes/sec
1 minute drop rate, 0 pkts/sec
5 minute input rate 0 pkts/sec, 0 bytes/sec
5 minute output rate 0 pkts/sec, 0 bytes/sec
5 minute drop rate, 0 pkts/sec
Aggregated Traffic on Physical Interface
<--- More --->
Ethernet0/0:
received (in 51431.740 secs):
10758462 packets10640075825 bytes
42 pkts/sec206042 bytes/sec
transmitted (in 51431.740 secs):
7548383 packets1029818127 bytes
63 pkts/sec20023 bytes/sec
1 minute input rate 485 pkts/sec, 537048 bytes/sec
1 minute output rate 395 pkts/sec, 54546 bytes/sec
1 minute drop rate, 0 pkts/sec
5 minute input rate 485 pkts/sec, 511723 bytes/sec
5 minute output rate 387 pkts/sec, 65495 bytes/sec
5 minute drop rate, 0 pkts/sec
Ethernet0/1:
received (in 51433.570 secs):
7749780 packets1066328930 bytes
67 pkts/sec20064 bytes/sec
transmitted (in 51433.570 secs):
10653359 packets10552787020 bytes
40 pkts/sec205006 bytes/sec
1 minute input rate 419 pkts/sec, 59621 bytes/sec
1 minute output rate 480 pkts/sec, 533950 bytes/sec
1 minute drop rate, 0 pkts/sec
5 minute input rate 399 pkts/sec, 67618 bytes/sec
<--- More --->
5 minute output rate 482 pkts/sec, 511073 bytes/sec
5 minute drop rate, 0 pkts/sec
Ethernet0/2:
received (in 51434.730 secs):
0 packets0 bytes
0 pkts/sec0 bytes/sec
transmitted (in 51434.730 secs):
0 packets0 bytes
0 pkts/sec0 bytes/sec
1 minute input rate 0 pkts/sec, 0 bytes/sec
1 minute output rate 0 pkts/sec, 0 bytes/sec
1 minute drop rate, 0 pkts/sec
5 minute input rate 0 pkts/sec, 0 bytes/sec
5 minute output rate 0 pkts/sec, 0 bytes/sec
5 minute drop rate, 0 pkts/sec
Ethernet0/3:
received (in 51434.730 secs):
0 packets0 bytes
0 pkts/sec0 bytes/sec
transmitted (in 51434.730 secs):
0 packets0 bytes
0 pkts/sec0 bytes/sec
1 minute input rate 0 pkts/sec, 0 bytes/sec
1 minute output rate 0 pkts/sec, 0 bytes/sec
<--- More --->
1 minute drop rate, 0 pkts/sec
5 minute input rate 0 pkts/sec, 0 bytes/sec
5 minute output rate 0 pkts/sec, 0 bytes/sec
5 minute drop rate, 0 pkts/sec
Ethernet0/4:
received (in 51434.870 secs):
0 packets0 bytes
0 pkts/sec0 bytes/sec
transmitted (in 51434.870 secs):
0 packets0 bytes
0 pkts/sec0 bytes/sec
1 minute input rate 0 pkts/sec, 0 bytes/sec
1 minute output rate 0 pkts/sec, 0 bytes/sec
1 minute drop rate, 0 pkts/sec
5 minute input rate 0 pkts/sec, 0 bytes/sec
5 minute output rate 0 pkts/sec, 0 bytes/sec
5 minute drop rate, 0 pkts/sec
Ethernet0/5:
received (in 51434.870 secs):
0 packets0 bytes
0 pkts/sec0 bytes/sec
transmitted (in 51434.870 secs):
0 packets0 bytes
0 pkts/sec0 bytes/sec
<--- More --->
1 minute input rate 0 pkts/sec, 0 bytes/sec
1 minute output rate 0 pkts/sec, 0 bytes/sec
1 minute drop rate, 0 pkts/sec
5 minute input rate 0 pkts/sec, 0 bytes/sec
5 minute output rate 0 pkts/sec, 0 bytes/sec
5 minute drop rate, 0 pkts/sec
Ethernet0/6:
received (in 51435.010 secs):
0 packets0 bytes
0 pkts/sec0 bytes/sec
transmitted (in 51435.010 secs):
0 packets0 bytes
0 pkts/sec0 bytes/sec
1 minute input rate 0 pkts/sec, 0 bytes/sec
1 minute output rate 0 pkts/sec, 0 bytes/sec
1 minute drop rate, 0 pkts/sec
5 minute input rate 0 pkts/sec, 0 bytes/sec
5 minute output rate 0 pkts/sec, 0 bytes/sec
5 minute drop rate, 0 pkts/sec
Ethernet0/7:
received (in 51435.010 secs):
0 packets0 bytes
0 pkts/sec0 bytes/sec
transmitted (in 51435.010 secs):
<--- More --->
0 packets0 bytes
0 pkts/sec0 bytes/sec
1 minute input rate 0 pkts/sec, 0 bytes/sec
1 minute output rate 0 pkts/sec, 0 bytes/sec
1 minute drop rate, 0 pkts/sec
5 minute input rate 0 pkts/sec, 0 bytes/sec
5 minute output rate 0 pkts/sec, 0 bytes/sec
5 minute drop rate, 0 pkts/sec
Internal-Data0/0:
received (in 51435.510 secs):
18513901 packets11784250044 bytes
25 pkts/sec229023 bytes/sec
transmitted (in 51435.510 secs):
18207269 packets11641332179 bytes
19 pkts/sec226078 bytes/sec
1 minute input rate 891 pkts/sec, 595715 bytes/sec
1 minute output rate 863 pkts/sec, 588935 bytes/sec
1 minute drop rate, 0 pkts/sec
5 minute input rate 885 pkts/sec, 584035 bytes/sec
5 minute output rate 870 pkts/sec, 580393 bytes/sec
5 minute drop rate, 0 pkts/sec
Internal-Data0/1:
received (in 51436.010 secs):
18207323 packets11641364184 bytes
<--- More --->
19 pkts/sec226076 bytes/sec
transmitted (in 51436.010 secs):
18513954 packets11784281987 bytes
25 pkts/sec229022 bytes/sec
1 minute input rate 855 pkts/sec, 575808 bytes/sec
1 minute output rate 884 pkts/sec, 582339 bytes/sec
1 minute drop rate, 0 pkts/sec
5 minute input rate 869 pkts/sec, 578350 bytes/sec
5 minute output rate 883 pkts/sec, 581924 bytes/sec
5 minute drop rate, 0 pkts/sec
------------------ show perfmon ------------------
PERFMON STATS: Current Average
Xlates 0/s 0/s
Connections 17/s 6/s
TCP Conns 8/s 2/s
UDP Conns 7/s 2/s
URL Access 0/s 0/s
URL Server Req 0/s 0/s
TCP Fixup 0/s 0/s
TCP Intercept 0/s 0/s
HTTP Fixup 0/s 0/s
<--- More --->
FTP Fixup 0/s 0/s
AAA Authen 0/s 0/s
AAA Author 0/s 0/s
AAA Account 0/s 0/s
------------------ show counters ------------------
Protocol Counter Value Context
IP IN_PKTS 168960 Summary
IP OUT_PKTS 169304 Summary
IP TO_ARP 61 Summary
------------------ show history ------------------
------------------ show firewall ------------------
Firewall mode: Transparent
------------------ show running-config ------------------
<--- More --->
: Saved
ASA Version 7.2(3)
firewall transparent
hostname ciscoasa
enable password
names
interface Vlan1
nameif inside
security-level 100
interface Vlan2
nameif outside
security-level 0
interface Ethernet0/0
switchport access vlan 2
interface Ethernet0/1
interface Ethernet0/2
<--- More --->
interface Ethernet0/3
interface Ethernet0/4
interface Ethernet0/5
interface Ethernet0/6
interface Ethernet0/7
passwd
regex domain1 ".facebook\.com"
regex domain2 ".fb\.com"
regex domain3 ".youtube\.com"
ftp mode passive
access-list ACL_IN extended permit ip any any
pager lines 24
mtu inside 1500
mtu outside 1500
ip address 192.168.1.254 255.255.255.0
icmp unreachable rate-limit 1 burst-size 1
asdm image disk0:/asdm-523.bin
no asdm history enable
<--- More --->
arp timeout 14400
access-group ACL_IN in interface outside
timeout xlate 3:00:00
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout uauth 0:05:00 absolute
no snmp-server location
no snmp-server contact
snmp-server enable traps snmp authentication linkup linkdown coldstart
telnet timeout 5
ssh timeout 5
console timeout 0
class-map type regex match-any DomainBlockList
match regex domain1
match regex domain2
match regex domain3
class-map inspection_default
match default-inspection-traffic
policy-map type inspect dns preset_dns_map
parameters
<--- More --->
message-length maximum 512
match domain-name regex class DomainBlockList
drop-connection log
policy-map global_policy
class inspection_default
inspect dns preset_dns_map
inspect ftp
inspect h323 h225
inspect h323 ras
inspect rsh
inspect rtsp
inspect esmtp
inspect sqlnet
inspect skinny
inspect sunrpc
inspect xdmcp
inspect sip
inspect netbios
inspect tftp
service-policy global_policy global
prompt hostname context
Cryptochecksum:bb5115ea1d14ee42e7961ef0c9aaed86
: end
<--- More --->
------------------ show startup-config errors ------------------
INFO: No configuration errors
------------------ console logs ------------------
Message #1 : Message #2 : Message #3 : Message #4 : Message #5 : Message #6 : Message #7 : Message #8 : Message #9 : Message #10 : Message #11 : Message #12 : Message #13 : Message #14 :
Total SSMs found: 0
Message #15 :
Total NICs found: 10
Message #16 : 88E6095 rev 2 Gigabit Ethernet @ index 09Message #17 : MAC: 0000.0003.0002
Message #18 : 88E6095 rev 2 Ethernet @ index 08Message #19 : MAC: 001f.9ee8.ffa1
Message #20 : 88E6095 rev 2 Ethernet @ index 07Message #21 : MAC: 001f.9ee8.ffa0
Message #22 : 88E6095 rev 2 Ethernet @ index 06Message #23 : MAC: 001f.9ee8.ff9f
Message #24 : 88E6095 rev 2 Ethernet @ index 05Message #25 : MAC: 001f.9ee8.ff9e
Message #26 : 88E6095 rev 2 Ethernet @ index 04Message #27 : MAC: 001f.9ee8.ff9d
Message #28 : 88E6095 rev 2 Ethernet @ index 03Message #29 : MAC: 001f.9ee8.ff9c
Message #30 : 88E6095 rev 2 Ethernet @ index 02Message #31 : MAC: 001f.9ee8.ff9b
Message #32 : 88E6095 rev 2 Ethernet @ index 01Message #33 : MAC: 001f.9ee8.ff9a
Message #34 : y88acs06 rev16 Gigabit Ethernet @ index 00 MAC: 001f.9ee8.ffa2
Message #35 :
Licensed features for this platform:
Message #36 : Maximum Physical Interfaces : 8
<--- More --->
Message #37 : VLANs : 3, DMZ Restricted
Message #38 : Inside Hosts : Unlimited
Message #39 : Failover : Disabled
Message #40 : VPN-DES : Enabled
Message #41 : VPN-3DES-AES : Enabled
Message #42 : VPN Peers : 10
Message #43 : WebVPN Peers : 2
Message #44 : Dual ISPs : Disabled
Message #45 : VLAN Trunk Ports : 0
Message #46 :
This platform has a Base license.
Message #47 :
Message #48 : Encryption hardware device : Cisco ASA-5505 on-board accelerator (revision 0x0)
Message #49 : Boot microcode : CNlite-MC-Boot-Cisco-1.2
Message #50 : SSL/IKE microcode: CNlite-MC-IPSEC-Admin-3.03
Message #51 : IPSec microcode : CNlite-MC-IPSECm-MAIN-2.04
Message #52 : --------------------------------------------------------------------------
Message #53 : . .
Message #54 : | |
Message #55 : ||| |||
Message #56 : .|| ||. .|| ||.
Message #57 : .:||| | |||:..:||| | |||:.
Message #58 : C i s c o S y s t e m s
Message #59 : --------------------------------------------------------------------------
<--- More --->
Message #60 :
Cisco Adaptive Security Appliance Software Version 7.2(3)
Message #61 :
Message #62 : ****************************** Warning *******************************
Message #63 : This product contains cryptographic features and is
Message #64 : subject to United States and local country laws
Message #65 : governing, import, export, transfer, and use.
Message #66 : Delivery of Cisco cryptographic products does not
Message #67 : imply third-party authority to import, export,
Message #68 : distribute, or use encryption. Importers, exporters,
Message #69 : distributors and users are responsible for compliance
Message #70 : with U.S. and local country laws. By using this
Message #71 : product you agree to comply with applicable laws and
Message #72 : regulations. If you are unable to comply with U.S.
Message #73 : and local laws, return the enclosed items immediately.
Message #74 :
Message #75 : A summary of U.S. laws governing Cisco cryptographic
Message #76 : products may be found at:
Message #77 : http://www.cisco.com/wwl/export/crypto/tool/stqrg.html
Message #78 :
Message #79 : If you require further assistance please contact us by
Message #80 : sending email to [email protected].
Message #81 : ******************************* Warning *******************************
Message #82 :
<--- More --->
Message #83 : Copyright (c) 1996-2007 by Cisco Systems, Inc.
Message #84 : Restricted Rights Legend
Message #85 : Use, duplication, or disclosure by the Government is
Message #86 : subject to restrictions as set forth in subparagraph
Message #87 : (c) of the Commercial Computer Software - Restricted
Message #88 : Rights clause at FAR sec. 52.227-19 and subparagraph
Message #89 : (c) (1) (ii) of the Rights in Technical Data and Computer
Message #90 : Software clause at DFARS sec. 252.227-7013.
Message #91 : Cisco Systems, Inc.
Message #92 : 170 West Tasman Drive
Message #93 : San Jose, California 95134-1706
ciscoasa# -
Cisco ASA 5505 doesn't forware incoming connection to LAN
Hello everybody.
I just got a Cisco asa 5505 with the next OS and ASDM info
ASA 5505 OS 8.4(3) ASDM 6.47
I configured and enter all rules to allow incoming traffic to LAN but it's not working also, I have one host inside that is configured in a second IP and create the rule to allow traffic to it but it doesn't work too.
Problem 1
I have VNC running in port 5900 tcp and I want to connect from Internet using port 6001 and this has to forware the connection to the real VNC port. In the configuration I have a few host with the same configuration but I use different outside port to get it.
Problem 2.
I have a second IP with services: SMTP, HTTP, HTTPS and port 444 all TCP forwarding to a server in the LAN.
Facts:
SMTP.
Every time that I do telnet to the second IP looking for the SMTP port, the firewall doesn't let the incoming connection goes through and the LOGGING screen doesn't how that connection.
PORT 6001 (outside)
this port is configured to work with the IP in the outside internface and it was to send the incoming connection to a host inside to the real port 5900.
Can any one check my configuration if I'm missing anything? for sure I'm but I didn't find it. Bellow is the configuration, I masked the Public IPs just left the last number in the IP, also I left the LAN network to see better the configuration.
I will appreciate any help.
Thanks a lot..
CONFIGURATION.
: Saved
ASA Version 8.4(3)
hostname saturn1
domain-name mydominio.com
enable password SOMEPASS encrypted
passwd SOMEPASS encrypted
names
name 192.168.250.11 CAPITOLA-LAN
name 192.168.250.15 OBIi110-LAN
name 192.168.250.21 DRP1260-LAN
name 192.168.250.22 HPOJ8500-LAN
name 192.168.250.30 AP-W77-NG-LAN
name 192.168.250.97 AJ-DTOP-PC-LAN
name 192.168.250.96 SWEETHEART-PC-LAN
name 192.168.250.94 KIDS-PC-LAN
name XX.YY.ZZ.250 EXTERNALIP
name XX.YY.ZZ.251 EXTERNALIP2
name XX.YY.ZZ.1 GTWAY
dns-guard
interface Ethernet0/0
switchport access vlan 2
interface Ethernet0/1
interface Ethernet0/2
interface Ethernet0/3
interface Ethernet0/4
interface Ethernet0/5
interface Ethernet0/6
interface Ethernet0/7
interface Vlan1
nameif inside
security-level 100
ip address 192.168.250.2 255.255.255.0
interface Vlan2
nameif outside
security-level 0
ip address EXTERNALIP 255.255.255.0
boot system disk0:/asa843-k8.bin
ftp mode passive
dns server-group DefaultDNS
domain-name mydominio.com
object network CAPITOLA-LAN
host 192.168.250.11
object network EXTERNALIP
host XX.YY.ZZ.250
description Created during name migration
object network CAPITOLA-PUBLIC
host XX.YY.ZZ.251
object network capitola-int
host 192.168.250.11
object network capitola-int-vnc
host 192.168.250.11
object network aj-dtop-int-vnc
host 192.168.250.97
object network sweetheart-int-vnc
host 192.168.250.96
object network kids-int-vnc
host 192.168.250.94
object network VPNNetwork
subnet 10.10.20.0 255.255.255.0
object network InsideNetwork
subnet 192.168.250.0 255.255.255.0
object network obj_any
subnet 0.0.0.0 0.0.0.0
object network capitola-int-smtp
host 192.168.250.11
object-group service capitola-int-smtp-service tcp
port-object eq smtp
object-group service capitola-int-services tcp
port-object eq smtp
port-object eq https
port-object eq www
port-object eq 444
object-group service capitola-int-vnc-service tcp
port-object eq 6001
object-group service aj-dtop-int-vnc-service tcp
port-object eq 6002
object-group service sweetheart-int-vnc-service tcp
port-object eq 6003
object-group service kids-int-vnc-service tcp
port-object eq 6004
access-list incoming extended permit icmp any any
access-list incoming extended permit tcp any object capitola-int object-group capitola-int-services
access-list incoming extended permit tcp any object capitola-int-vnc object-group capitola-int-vnc-service
access-list incoming extended permit tcp any object aj-dtop-int-vnc object-group aj-dtop-int-vnc-service
access-list incoming extended permit tcp any object sweetheart-int-vnc object-group sweetheart-int-vnc-service
access-list incoming extended permit tcp any object kids-int-vnc object-group kids-int-vnc-service
access-list incoming extended permit tcp any object capitola-int-smtp object-group capitola-int-smtp-service
access-list split-tunnel standard permit 192.168.250.0 255.255.255.0
access-list inside_nat0_outbound extended permit ip any object VPNNetwork
pager lines 24
logging enable
logging asdm informational
mtu inside 1500
mtu outside 1500
ip local pool vpnpool 10.10.20.1-10.10.20.50 mask 255.255.255.0
icmp unreachable rate-limit 1 burst-size 1
asdm image disk0:/asdm-647.bin
no asdm history enable
arp timeout 14400
nat (inside,any) source static any any destination static VPNNetwork VPNNetwork no-proxy-arp
object network capitola-int
nat (any,any) static XX.YY.ZZ.251
object network capitola-int-vnc
nat (inside,outside) static interface service tcp 5900 6001
object network aj-dtop-int-vnc
nat (inside,outside) static interface service tcp 5900 6002
object network sweetheart-int-vnc
nat (inside,outside) static interface service tcp 5900 6003
object network kids-int-vnc
nat (inside,outside) static interface service tcp 5900 6004
object network obj_any
nat (inside,outside) dynamic interface
object network capitola-int-smtp
nat (any,outside) static interface service tcp smtp smtp
access-group incoming in interface outside
route outside 0.0.0.0 0.0.0.0 GTWAY 1
timeout xlate 3:00:00
timeout pat-xlate 0:00:30
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
timeout floating-conn 0:00:00
dynamic-access-policy-record DfltAccessPolicy
user-identity default-domain LOCAL
aaa authentication ssh console LOCAL
http server enable
http server idle-timeout 2
http server session-timeout 1
http 192.168.1.0 255.255.255.0 inside
http CAPITOLA-LAN 255.255.255.255 inside
http AJ-DTOP-PC-LAN 255.255.255.255 inside
no snmp-server location
no snmp-server contact
snmp-server enable traps snmp authentication linkup linkdown coldstart
telnet timeout 5
ssh CAPITOLA-LAN 255.255.255.255 inside
ssh AJ-DTOP-PC-LAN 255.255.255.255 inside
ssh timeout 15
console timeout 0
vpn-addr-assign local reuse-delay 2
dhcpd auto_config outside
threat-detection basic-threat
threat-detection statistics access-list
no threat-detection statistics tcp-intercept
webvpn
username admin password SOMEPASS encrypted privilege 15
class-map inspection_default
match default-inspection-traffic
policy-map type inspect dns preset_dns_map
parameters
message-length maximum 512
policy-map global_policy
class inspection_default
inspect dns preset_dns_map
inspect ftp
inspect h323 h225
inspect h323 ras
inspect rsh
inspect rtsp
inspect sqlnet
inspect skinny
inspect sunrpc
inspect xdmcp
inspect sip
inspect netbios
inspect tftp
inspect pptp
inspect ip-options
service-policy global_policy global
prompt hostname context
no call-home reporting anonymous
call-home
profile CiscoTAC-1
no active
destination address http https://tools.cisco.com/its/service/oddce/services/DDCEService
destination address email [email protected]
destination transport-method http
subscribe-to-alert-group diagnostic
subscribe-to-alert-group environment
subscribe-to-alert-group inventory periodic monthly
subscribe-to-alert-group configuration periodic monthly
subscribe-to-alert-group telemetry periodic daily
Cryptochecksum:036b82d3eb5cffc1c65a3b381246d043
: end
asdm image disk0:/asdm-647.bin
no asdm history enableJose, your fix to problem 1 allows all access from the outside, assuming you applied the extended list to the outside interface. Try to be more restrictive than an '...ip any any' rule for outside_in connections. For instance, this is what I have for incoming VOIP (access list and nat rules):
access list rule:
access-list outside_access_in extended permit udp any object server range 9000 9049 log errors
nat rule:
nat (inside,outside) source static server interface service voip-range voip-range
- 'server' is a network object *
- 'voip-range' is a service group range
I'd assume you can do something similar here in combination with my earlier comment:
access-list incoming extended permit tcp any any eq 5900
Can you explain your forwarding methodology a little more? I'm by no means an expert on forwarding, but the way I read what you're trying to do is that you have an inbound VNC request coming in on 5900 and you want the firewall to figure out which host the request should go to. Or is it vice-versa, the inbound VNC request can be on port 6001-6004 ? -
Cisco asa 5505 with Router 881w Configuration Help
Hello all,
I'm having trouble setting up a second vlan to route to the internet. I have a Cisco ASA 5505 connected to my ISP(OUTSIDE) and a Cisco 881w (INSIDE) router in the back of my firewall. My vlan 10 with the network 192.168.5.1 255.255.255.0 works with pat, however vlan 15 that is on my 881w router does not route to the internet at all. I can only ping from 192.168.15.15 network to 192.168.5.1 I would like some advice on how can I make this set up work. Attached with this discussion is a picture of my topology.
Thanks in advance.
here are the show runs:
Cisco ASA 5505 show run:
ASA Version 8.3(1)
names
interface Vlan1
no nameif
no security-level
no ip address
interface Vlan5
mac-address xxxx.xxxx.xxxx
nameif OUTSIDE
security-level 0
ip address dhcp setroute
interface Vlan10
nameif INSIDE
security-level 100
ip address 192.168.5.1 255.255.255.0
interface Ethernet0/0
switchport access vlan 5
interface Ethernet0/1
switchport access vlan 10
interface Ethernet0/2
interface Ethernet0/3
shutdown
interface Ethernet0/4
shutdown
interface Ethernet0/5
shutdown
interface Ethernet0/6
shutdown
interface Ethernet0/7
shutdown
ftp mode passive
clock timezone CST -6
clock summer-time CDT recurring
object network INTERNAL_LAN
subnet 192.168.5.0 255.255.255.0
object network PRIVATE_LAN_192
subnet 192.168.15.0 255.255.255.224
description PRIVATE_LAN_192
access-list INSIDE_access_in extended permit ip any any
access-list INSIDE_access_in extended deny ip any any
access-list OUTSIDE_access_in extended permit ip any any
access-list OUTSIDE_access_in extended deny ip any any
pager lines 24
logging enable
mtu OUTSIDE 1500
mtu INSIDE 1500
ip verify reverse-path interface OUTSIDE
ip verify reverse-path interface INSIDE
no failover
icmp unreachable rate-limit 1 burst-size 1
no asdm history enable
arp timeout 14400
object network INTERNAL_LAN
nat (INSIDE,OUTSIDE) dynamic interface
object network PRIVATE_LAN_192
nat (INSIDE,OUTSIDE) dynamic interface
access-group OUTSIDE_access_in in interface OUTSIDE
access-group INSIDE_access_in in interface INSIDE
route INSIDE 192.168.15.0 255.255.255.224 192.168.5.2 1
dynamic-access-policy-record DfltAccessPolicy
http server enable
dhcpd dns 8.8.8.8 75.75.76.76
dhcpd address 192.168.5.10-192.168.5.100 INSIDE
dhcpd enable INSIDE
Router 881w show run:
Current configuration : 4912 bytes
version 12.4
no ip source-route
ip dhcp excluded-address 192.168.15.1 192.168.15.10
ip dhcp pool PRIVATE_LAN
network 192.168.15.0 255.255.255.224
interface FastEthernet0
switchport trunk allowed vlan 1,15,1002-1005
switchport mode trunk
interface FastEthernet1
interface FastEthernet2
interface FastEthernet3
interface FastEthernet4
ip address 192.168.5.2 255.255.255.0
duplex auto
speed auto
interface wlan-ap0
description Service module interface to manage the embedded AP
no ip address
arp timeout 0
interface Wlan-GigabitEthernet0
description Internal switch interface connecting to the embedded AP
interface Vlan1
no ip address
interface Vlan15
ip address 192.168.15.1 255.255.255.224
no ip forward-protocol nd
ip route 0.0.0.0 0.0.0.0 FastEthernet4
no ip http server
ip http authentication local
ip http secure-serverThe cable modem does not have any configuration. I cant add any to it. Its a cisco dpc3008. From vlan 10 i have no problem to get to the internet with the above configuration. My problem is just vlan 15.
-
Cisco ASA 5505 Site to site VPN IPSEC tunnel to an Clavister Firewall
Hi,
I have weird problem with a Site to site VPN tunnel from a Cisco ASA 5505 to an Clavister Firewall.
When I restart the Cisco ASA 5505 the tunnel is up and down,up, down, down, and I get all strange messages when I see if the tunnel is up or down with the syntax: show crypto isakmp sa
After a while like 5-10 min the vpn site to site tunnel is up and here is the strange thing happening I have all accesslists and tunnel accesslists right I can only access one remote network (Main site Clavister Firewall) trought the vpn tunnel behind the Cisco ASA 5505, and I have 5 more remote networks that I want to access but only one remote network is working trought the vpn tunnel behind the Cisco ASA. I see that when I do this syntax in ASA: show crypto ipsec sa.
They had a Clavister Firewall before on that site before and now they have a Cisco ASA 5505 and all the rules on the main site thats have the big Clavister Firewall is intact so the problems are in the Cisco ASA 5505.
Here is some logs that ASDM give me about the tunnel issue, but like I said, the tunnel is up and only one remote network is reachable in that tunnel.....
3
Nov 21 2012
07:11:09
713902
Group = 195.149.180.254, IP = 195.149.169.254, Removing peer from correlator table failed, no match!
3
Nov 21 2012
07:11:09
713902
Group = 195.149.180.254, IP = 195.149.169.254, QM FSM error (P2 struct &0xc92462d0, mess id 0x1c6bf927)!
3
Nov 21 2012
07:11:09
713061
Group = 195.149.180.254, IP = 195.149.169.254, Rejecting IPSec tunnel: no matching crypto map entry for remote proxy 0.0.0.0/0.0.0.0/0/0 local proxy 0.0.0.0/0.0.0.0/0/0 on interface outside
5
Nov 21 2012
07:11:09
713119
Group = 195.149.180.254, IP = 195.149.169.254, PHASE 1 COMPLETED
Here is from the syntax: show crypto isakmp sa
Result of the command: "show crypto isakmp sa"
Active SA: 1
Rekey SA: 0 (A tunnel will report 1 Active and 1 Rekey SA during rekey)
Total IKE SA: 1
1 IKE Peer: 195.149.180.254
Type : L2L Role : responder
Rekey : no State : MM_ACTIVE
Result of the command: "show crypto ipsec sa"
interface: outside
Crypto map tag: CustomerCryptoMap, seq num: 10, local addr: 213.180.90.29
access-list arvika_garnisonen permit ip 172.22.65.0 255.255.255.0 192.168.123.0 255.255.255.0
local ident (addr/mask/prot/port): (172.22.65.0/255.255.255.0/0/0)
remote ident (addr/mask/prot/port): (192.168.123.0/255.255.255.0/0/0)
current_peer:195.149.180.254
#pkts encaps: 2188, #pkts encrypt: 2188, #pkts digest: 2188
#pkts decaps: 2082, #pkts decrypt: 2082, #pkts verify: 2082
#pkts compressed: 0, #pkts decompressed: 0
#pkts not compressed: 2188, #pkts comp failed: 0, #pkts decomp failed: 0
#pre-frag successes: 0, #pre-frag failures: 0, #fragments created: 0
#PMTUs sent: 0, #PMTUs rcvd: 0, #decapsulated frgs needing reassembly: 0
#send errors: 0, #recv errors: 0
local crypto endpt.: 213.180.67.29, remote crypto endpt.: 195.149.180.254
path mtu 1500, ipsec overhead 74, media mtu 1500
current outbound spi: E715B315
inbound esp sas:
spi: 0xFAC769EB (4207372779)
transform: esp-aes-256 esp-sha-hmac no compression
in use settings ={L2L, Tunnel, PFS Group 5, }
slot: 0, conn_id: 2879488, crypto-map: CustomerCryptoMap
sa timing: remaining key lifetime (kB/sec): (38738/2061)
IV size: 16 bytes
replay detection support: Y
Anti replay bitmap:
0xFFFFFFFF 0xFFFFFFFF
outbound esp sas:
spi: 0xE715B315 (3876958997)
transform: esp-aes-256 esp-sha-hmac no compression
in use settings ={L2L, Tunnel, PFS Group 5, }
slot: 0, conn_id: 2879488, crypto-map: CustomerCryptoMap
sa timing: remaining key lifetime (kB/sec): (38673/2061)
IV size: 16 bytes
replay detection support: Y
Anti replay bitmap:
0x00000000 0x00000001
And here are my Accesslists and vpn site to site config:
crypto isakmp enable outside
crypto isakmp policy 10
authentication pre-share
encryption aes-256
hash sha
group 5
lifetime 84600
crypto isakmp nat-traversal 40
crypto ipsec transform-set ESP-AES-256-SHA esp-aes-256 esp-sha-hmac
crypto ipsec security-association lifetime seconds 28800
crypto ipsec security-association lifetime kilobytes 4608000
crypto map CustomerCryptoMap 10 match address VPN_Tunnel
crypto map CustomerCryptoMap 10 set pfs group5
crypto map CustomerCryptoMap 10 set peer 195.149.180.254
crypto map CustomerCryptoMap 10 set transform-set ESP-AES-256-SHA
crypto map CustomerCryptoMap interface outside
access-list VPN_Tunnel extended permit ip 172.22.65.0 255.255.255.0 192.168.123.0 255.255.255.0 -------> This is the only remote network I can reach behind the Cisco ASA and the other remote networks dont work..
access-list VPN_Tunnel extended permit ip 172.22.65.0 255.255.255.0 host 10.1.34.5
access-list VPN_Tunnel extended permit ip 172.22.65.0 255.255.255.0 host 10.1.20.76
access-list VPN_Tunnel extended permit ip 172.22.65.0 255.255.255.0 host 62.88.129.221
access-list VPN_Tunnel extended permit ip 172.22.65.0 255.255.255.0 172.22.71.0 255.255.255.0
access-list nonat extended permit ip 172.22.65.0 255.255.255.0 192.168.123.0 255.255.255.0
access-list nonat extended permit ip 172.22.65.0 255.255.255.0 host 10.1.34.5
access-list nonat extended permit ip 172.22.65.0 255.255.255.0 host 10.1.20.76
access-list nonat extended permit ip 172.22.65.0 255.255.255.0 host 62.88.129.221
access-list nonat extended permit ip 172.22.65.0 255.255.255.0 172.22.71.0 255.255.255.0
nat (inside) 0 access-list nonat
All these remote networks are at the Main Site Clavister Firewall.
Best Regards
MichaelHi,
I'd start by getting the configuration of the remote site related to Local/Remote network configurations and go through them. Even though no changes have been made.
If they are mirror images of eachother already I'd say its probably some problem related to Cisco/Clavister setup
Seems especially wierd to me that one of the error messages includes 0.0.0.0 lines.
I have run into some problems with L2L VPN configurations when our Cisco device just doesnt want to work with the remote end device. In some cases we have confirmed that our networks defined for the L2L VPN are exactly the same and yet when checking debugs on the ASA side we can see the remote end device using totally wrong network masks for the VPN negotiaton and therefore it failed. That problem we corrected with changing the network masks a bit.
Maybe you could try to change the Encryption Domain configurations a bit and test it then.
You could also maybe take some debugs on the Phase2 and see if you get anymore hints as to what could be the problem when only one network is working for the L2L VPN.
- Jouni
Maybe you are looking for
-
Is it still snowing in minnesota
has cougar escaped its bondage does birch tree have spring leaves is pig snorting happily away we may never know tttastcb
-
Hello everybody, I have a Process chain which contains a bunch of Variants and ABAp Pgms and other process. Now when i transport from Dev. to QA all of the process and variants gets transported except one of ABAP Pgm. To be more clear out of 5 abap p
-
Passing values to JavaBean function using jsp scriplet
Hi, I have a JavaBean funtion that is SaveData(parameters) which save the values from HTML form. Now i want a code for pass the values from HTML form to SaveData() function using jsp scriptlet. I used the code <jsp:useBean id="JDBC" class="bean.JDBCB
-
Can't play video with Extreme from NAS. Help.
Hi! I have bought AirPort Extreme 2013 and now I can't play video on my Home Theater. (Can't play video. This video file is not supported). Before I had ASUS RT-N66U router and video were played fine. The most of them. I mean *.avi, *.mkv and other c
-
Tabbed panel disappears in my pages
I am building a tabbed panel menu bar in a template in Dreamweaver, and the tabs keep disappearing. My template file is fine, and they view online, but any page I build from this template seems to hide the tabs or the little 'eye' icon disappears. I