ATA 186 Conf calls

I'm trying to set up an ATA 186 so that we can integrate it with our Polycom VCS. The ATA is set up as an SCCP device, and works fine as an analog line. What I need to do though, is set it up to use the BellCore mid-call service, as this seems to be the most "standard" way of initiating a conf call. Thus far I'm having no luck with the params to use to do this. Has anyone done this, and could you share any insite?
Thanks,
Alan

The ATA is limited to do 3 party conference call. ATA can support conference call. Please look at section 6.6 of EDCS-148811 for detail instructions.

Similar Messages

  • Proble to connect Cisco ATA 186

    After I purchased Cisco ATA 186, I connected to Cisco Call Manager 3.3.4, and it worked. I don't know the version of firmware at that time.
    Recently, I used my ATA 186 to test PC to Phone call. It is H323 gatekeeper. So, I upgraded the latest H323 3.01 firmware to my ATA 186. At this point, Cisco Call Manager did not get involved.
    Today, I used this H323, 3.01 version of SCCP, SIP and MGCP tried to reconnect to the call manager, and it failed. It is like ATA 186 and call manager does not know each other.
    How do I fix it ? Should I use the default firmware that came with the device ? Can you tell me what is the default firmware ?
    Product ID is ATA186-I1-A.

    the document below provides information about configuring Cisco CallManager to interoperate with the Cisco Analog Telephone Adapter (ATA) 186 using Skinny Client Control Protocol (SCCP) also known as "Skinny".
    http://www.cisco.com/en/US/products/hw/gatecont/ps514/products_configuration_example09186a00800a892f.shtml

  • !!cisco ATA 186, back to back.SOS

    hi there, just enlighten me on cisco ATA 186 back to back config, my network is like:
    phone---ATA----Switch---ATA---Phone,wnat to know the sample config, if this not possible, fine ,then let me know what shud i configure to get a dial tone,as im getting a busy tone than a dial tone, or lastly what shud i do to reset the ATAs to factory default settings,
    cheers
    shukky

    If your ATA is running skinny right now then I think it is not possible (because no callmanager in the picture).
    But if you load your ATA with a SIP image then in the SIP proxy filed, you can specify the IP address of the other SIP ATA and then you should be able to call from one ATA to another.
    I haven't tried that with the ATA, but done with the 7940 phones and it worked.
    To get the dial-tone, you must configure a number for the ATA first. (UID)
    To reset the ATA for factory defaults
    http://lists.digium.com/pipermail/asterisk-users/2003-August/017474.html
    Hope this would help.
    Thanks

  • ATA 186 Reproducing DTMF tones from RFC2833 events

    I am trying to get my ATA 186 (running version SCCP 3.x under CCM 5.04a) to reproduce received rtp-events. This is supporting a third-party IVR system that is connected via analog ports.
    The IOS gateway that is sending the events is configured for dtmf-relay rtp-nte, and I can see the RTP events being received at the ATA. However, all I hear at the ATA is nothing or clicks.
    I have the audiomode setting on the ATA set to 0x00150015 as is recommended in the ATA administrators guide.
    Does anyone have DTMF working through the ATA?

    Hi Kevin,
    have you debugged the ATA with prserv.exe?
    I had some issues in the past with a PESQ tester, and setting the audiomode to 0x00120012 helped for me.
    hth
    Sascha
    ....this is the output from prserv on a good call
    |->CallState[0]=4 L=1 R=4016c6c FG=0 r=0,0
    FG NewState[0]=4, L=1, R=4016c6c
    |->CallInfo[0]
    |->SetRingerMode[0]:3
    <-|StOffHk[0]
    |->SetRingerMode[0]:1
    |->CallState[0]=1 L=1 R=4016c6c FG=0 r=4016c6c,0
    |->SetRingerMode[0]:1
    [0]StopTone
    |->CallState[0]=5 L=1 R=4016c6c FG=0 r=4016c6c,0
    |->CallInfo[0]
    [0]StopTone
    |->OpenRxChn[0]
    [0]StopTone
    <-|OpenRxChnAck[0]
    Save Media[0]
    |->StartMediaTx[0]:pt=0 ps=20 ss=0 ip=a63801f:19422
    [0]MPT mode 0
    [2]MPT mode 0
    Enable LEC adapt [0]=1
    [0]Enable encoder 0
    [0]DPKT 1st: 3680 3520, pt 0
    15948:00;2,0,0,0,
    [0]DTMF 1 , insum:323505
    [0]StopTone
    [0]DTMF 2 , insum:285988
    [0]DTMF 3 , insum:289227
    [0]DTMF 4 , insum:287021
    [0]DTMF 5 , insum:284108
    [0]DTMF 6 , insum:286979
    [0]DTMF 7 , insum:284993
    [0]DTMF 8 , insum:302792
    [0]DTMF 9 , insum:293475
    [0]DTMF 0 , insum:293768
    [0]DTMF * , insum:279360
    [0]DTMF # , insum:301230
    <-|EndCall[0]
    <-|SK[0]:9, L=1, FGR=4016c6c
    [0]StopTone
    ->CloseRxChn[0]
    |->StopMediaTx[0]
    |->CallState[0]=2 L=1 R=4016c6c FG=0 r=4016c6c,0
    IDLE[0]
    |->SetRingerMode[0]:1
    15948:30;2,0,0,0,

  • ATA 186

    hi, i have a problem with ATA 186
    when I light on the ATA it work very well after a certain moment the calls doesn't pass anymore Im forced to reboot every time when this problem happend
    thanks

    IS this CCM? If so please report to IP telephony forum where there are many fellows that can help.
    If it is CCME I would start looking at the status of the ephone, and try to ping the ATA when it freezes.

  • ATA 186 Issue to send faxes

    Hi,
    I have an issue with ATA 186 to send faxes. I have tried many things, but the fax sending  is unsuccessful. I am not a VoIP expert, so it is pretty hard to me to identify the difference between some commands. This is the topology of the network:
    Fax Machine --- ATA ---- CCM ---- VoIPGW --- E1(PSTN)
    I have the following values in ATA:
    AudioMode: 0x00120012
    ConnectMode: 0x00008400
    This is the dial-peer configured to that Fax:
    dial-peer voice 1010 voip
    call-block translation-profile incoming 110
    call-block disconnect-cause incoming call-reject
    preference 1
    destination-pattern 1044
    voice-class h323 1
    session target ipv4:10.15.190.4
    dtmf-relay cisco-rtp h245-signal h245-alphanumeric
    codec g711ulaw
    fax rate disable
    fax protocol pass-through g711ulaw
    no vad
    Aditionaly I had the following lines in VoIPGW:
    ccm-manager fax protocol cisco
    mgcp
    mgcp fax t38 ecm
    Recently I changed to:
    no ccm-manager fax protocol cisco
    mgcp
    mgcp fax t38 inhibit
    Not sure if I missing something, in the other hand I would like to know which is the different between  fax protocol pass-through g711ulaw and modem passthrough nse codec g711ulaw
    Thanks for your comments....

    Hello,
    There is one relly important detail on this matter, is the fax machine a super G3 fax machine? this is because as you mention there are some limitation for the ATAs to work with fax machines and modems, this is because the device was not designed for this purpose.}
    In the follow link you could find some information about the ATA configuration for faxing:
    http://www.cisco.com/en/US/partner/products/hw/gatecont/ps514/products_qanda_item09186a00800946e1.shtml
    Another important detail is check if your gateway supports the type of faxing that you are trying to do
    http://www.cisco.com/en/US/partner/tech/tk652/tk777/technologies_tech_note09186a0080159cf3.shtml
    Finally this are the configuration steps for you voice gaway:
    http://www.cisco.com/en/US/partner/docs/ios/12_3/vvf_c/cisco_ios_fax_services_over_ip_application_guide/pt.html
    HTH
    <-------------------->
    Walter    Solano
    CCNA Voice
    UCCX Specialis

  • ATA-186 can be registered with CUCM v10.5

    Hello guys ;
                          Please confirm me that ATA-186 can work with CUCM v10.5 ? .
    Regards;
    Shib

    Loaded the latest firmware into CM, then manually on ATA firmware using this process as CM didn't change it:
    http://www.cisco.com/c/en/us/td/docs/voice_ip_comm/cata/186_188/3_0/english/administration/guide/sccp/sccp3_0/sccpaapc.html#wp1011450
    I followed this link from another post regarding ASA not registering for an older issue.
    http://www.cisco.com/en/US/docs/voice_ip_comm/cata/186_188/3_0/english/administration/guide/sccp/sccpaape.html#wpxref59054
    Follow the part that mentions setting the SID0 & SID1 to "." no quotes.  I did this and my ATA registered to CM.  Screen caps attached.
    I have a Cisco ATA 186 running on 10.5.1 and it shows to be registered.  I can make calls on it.  Not sure how it will do for faxes.  HTH Please rate.

  • Remote-Party-ID with ATA 186

    The remote-party-id field in my invite message to an ATA 186 does not appear to be tranlating properly to caller-id. Does the ATA support Remote-Party-ID? If so, do I have to modify any settings? Currently, the from address is showing up in the caller-id screen of a phone connected to the ATA.
    Thanks,
    Stephen

    Hello,
    Can You please forward the URL which tells the configuration part to be taken place
    Regards
    pavan.M

  • Ata 186 second port problem

    Hello
    There are a atas186 who was registered to a CUCM version 6.1,the call manager was migrated to version 8.6 but now the second por when a call is answered immediately when give a fast busy tone, the first port works perfect, and i have changed many parameters and did a factory reset without success.
    S/W Version 3.02.04(090202A)
    App Load ID ATA030204SCCP090202A
    Thanks.

    Your ata´s place calls  across the wan?
    If yes, the the ata 186, only support one port in g729 codec the port 0, the second port works only in g711 codec so try to configure a region to place calls only in g711 codec across the wan and problem solve
    i hope it helps...

  • ATA 186 - HP FAX Accessory 300

    We have an ATA 186 which we want to connect to our MFD. When we connect the device to the MFD and ring the port the MFD will not answer the call. If we connect to a VG224 the MFD detects ring ok and answers the call. If we plug a POT into the ATA the phone rings ok so we know there is an issue between the ring voltage of the ATA 40v and what the HP MDF is expecting. The MFD is a Q7519A but I can't find any info on the ring voltage required. Any Suggestions?

    This is my suggestion:
    - check if the telephony cable has only 1 couple of wire (tip and ring only); in the past I had some problems with cable with 4 wire (2 couple); the ATA had a strange behavior;
    - try to connect an analog telephone to the ATA186 and verify if it works;
    - if the problem persists probably the ATA has an hardware fault;
    - try with a different ATA;
    Best Regards.

  • ATA 186 and Cisco CallManager

    I am trying to setup a cisco ATA 186 for a fax line with Cisco Call Manager 6.1.xxxx)  I have a telephone hooked up to the Cisco ATA 186 and I see it register with the CCM.  I have a telphone connected to port one and I get a dial tone, I can call into the phone from an outside line but it seems I cant dial to an outside number all I get is silence. 
    Could someone point me into a direction on troubleshooting this issue?
    Thanks!

    Verify software versions first.
    http://www.cisco.com/en/US/docs/voice_ip_comm/cucm/compat/ccmcompmatr.html#wp50035
    After that, you would really need to look at traces to find out why the audio isn't getting connected.  Do phones on the same subnet have audio when you call in?  Does this only happen on outside calls?  If it only happens on outside calls, get a sniffer to see if you see the RTP traffic coming to and from the devices.
    -Steven

  • 1751-V & ATA-186 Incompatibility

    Hi There,
    I have a VoIP network, of two Cisco 1750-4V, two Cisco 1751-V multiservice routers and two ATA-186 voice gateways.
    The communication between any 1750-4V and ATA-186 devices is flawless in both directions. However, when we try to make a call from 1751-V (FXO or FXS port) to the ATA-186, it's impossible. The communication from any ATA-186 to any 1750-4V, the other ATA-186, and any 1751-V (FXO or FXS port) is flawless.
    I don't know if a newer version of ATA-186 flash ROM (actually there is 2.07 version) will solve this problem?
    I will appreciate any comments.
    Regards,
    Igor Sotelo.

    Thank you for the information.
    We don't use a gatekeeper, and I have the following configuration on both 1751-V (the configuration is the same on the 1750-4V's):
    dial-peer voice 5000 voip
    .destination-pattern 500.
    .session target ipv4:x.y.z.w
    where x.y.z.w is a external valid IP address.
    On the ATA-186 we have configured:
    static IP: x.y.z.w
    static net mask: 255.255.255.240
    UID0: 5000
    UID1: 5001
    and static route: x.y.z.w1
    I can ping the devices from the 1751-V without problems, and also call the 1751-V from the ATA. However, I can't call the ATA from the 1751-V.
    Do you have idea, of what can be wrong?
    Regards,
    Igor Sotelo.

  • Issue on Cisco ATA 186 used for Fax

    Hello everyone;
    I have a cisco ATA 186 connected to an analog Fax on one side, and the other side is connected to the network containing a CUCM 8.6.
    The problem is that when i try to send a fax throught it , half of the paper is transmitted or an usual occupation tone comes; while vocal communications are performed normaly.
    Any idea of what could be the problem.
    NB: the fax emission is between two distant sites relied by optical fiber.
    Regards. 

    Hello Frank;
    Thank for the reply.
    Here below more informations about the issue:
    - It does work sometimes, but it did never worked properly.
    - the problem is there for both sending and receiving.
    - for the PSTN transport, i have no idea.   
    - I tried to change the ATA by another, still the same problem.
    - ATAs work properly for voice communication.
    - when i call this fax number internally the signal comes along.
    - the problem is when faxing internally, it isn't used for external faxing.
    - the call flow for internal faxing is like this:
    Analog fax (in site A) > ATA (in site A) > access switch (in site A) > core switch (in site A) > cucm (in site A) > Core switch (in site A) > router (in site A) > optical fiber > router (in site B) > core switch (in site B) > cucm (in site B) > core switch (in site B) > voice gateway 248 (in site B) > Analog fax (in site B).
    the problem occures when sending internal fax between these two sites A and B, when calling site B from site A, the ringing tone comes aloso the fax signal, but when i try the send the paper the stange tone come along and only half of it pass and it get to the site B as a blank paper or a half blank paper.
    for any more explanation, don't hesitate to ask me.
    thanks again for your time.
    Regards.

  • ATA 186 status

    Hi,
    How is it possible to check the status of ATA 186?
    Is it registered with a SIP server?
    Is there an active conversation?
    Which phone port is in use?
    What codec is being used?
    What is the current packet rate/bandwidth consumption for a call?
    How to check for possible system issues/errors?
    Does ATA 186 have a command line interface?
    Thanks.
    Alex

    Hi
    Cisco ATA 186 has an IVR which can be accessed through your phone.
    http://www.cisco.com/en/US/products/hw/gatecont/ps514/products_configuration_example09186a00800c3a50.shtml
    Once the IP address is set through IVR, the device can be accessed through "http:///dev"
    Pls rate the helpful posts.
    Regards
    JD

  • Troubleshooting an ATA 186

    How can I tell what digits are being passed from a phone plugged into an ATA 186?
    We have an ATA 186 with a credit card machine plugged into it that is failing to place calls. When I monitor the call with a butt set I hear dial tone, then 1 digit being dialed and then an error from callmanager basically telling me to check the number. The call never gets past that first digit. If I use a butt set to place a call everything works fine. I'm concerned the digit being passed is not the access code of 8, and I want to verify that. I have also included the 9001.log from the prsrev.exe I just don't know how to read it.

    Hi,
    It look to me like the ATA isn't configured properly in CCM?
    There's a lot of messages in the log stating "RegRej[1]:Error: DB Config", which I think means the device isn't registering properly.
    Have you checked the ports are configured properly?
    Here's a troubleshooting guide which may also help:
    http://www.cisco.com/en/US/products/hw/gatecont/ps514/products_configuration_example09186a0080094adf.shtml
    Please rate if useful...

Maybe you are looking for

  • Adobe After effects better on pc or mac?

    adobe after effects run better on a mac or pc?

  • E72 I can not open office documents from my email ...

    I have the phone for two months and already I have two problems. For two weeks I can not open office documents from my email and I can not connect the phone via Bluetooth to my computer.

  • Unable to delete anything on page/form

    Hi, I seem to be having a problem with deleting objects from my form in application developer mode and in multi row deletes in form mode. I am able to add and amend objects such as buttons to the form etc but when I try and delete, nothing happens. I

  • Need to run 2 versions of FF, diferent privacy settings

    I have FF12 and it is set up the way I want it to so I feel that my anonymity is protected. Problem is now I am starting to do research and I need to have different privacy settings. Is there a way to run 2 versions of FF AND have different privacy s

  • Apple TV cable hookup

    Is there cable adapters available that would let you hook up an Apple TV to an older TV with RCA hookups (yellow for video, red and white for audio)?