ATA vs VG202 vs VIC3-2FXS-E/DID & Wireless

What is best solution moving forward?
Fax server probably two years out.
Background:
I have 34 locations
30 locations have 2 analog devices
4 Operations have 26, 14, 15, 10 analog devices
Currently we use ATA 188 and 186 and one VIC2-2FXS
We Have intermittent problems receiving faxes from Fax servers or other customers in general.

The VG20x are nice because you can use them as a full blown router (VPN, IGP, etc).
I think you'll have more cost per port using a VIC3 rather than VG204. Their capabilities will be equal, as opposed to when the ATAs were in use.
The ATAs are on their way out, and I think you'll find the VG20x to be an easier product to use and it will work better with faxes/modems. The ATAs don't have great fax/modem support where the VG20x will have T38 support and modem support.
For the locations with 15+ devices it may be worth looking into the VG224 as well, depending on usage.
-nick

Similar Messages

VIC3-2FXS/DID VS VIC3-2FXS-E/DID

hi all,
we'll upgrade our router from 2811 to 2911.
the current 2811 uses VIC2-2FXS but saw on cisco's website that we need a VIC3 instead.
i saw there's two versions of this card, the other has an 'E'.
what's the difference between the two? can i just get a VIC3-2FXS/DID?

Hi John,
The difference is explained in the following link
http://www.cisco.com/c/en/us/products/collateral/interfaces-modules/ip-communications-voice-fax-network-modules/product_data_sheet0900aecd801c595e.html
VIC3-2FXS-E/DID is designated as an "Off-Premise Extension Lite" product offering. This means that while the module addresses a subset of the off-premise extension applications, it should be noted that the module is not in full compliance for off-premise usage.
HTH
Manish

How to install 2-port vic3 2fxs/DID and 2-port vic2 fxo on cisco 2801 router

Hello
I'm looking for information on how to install 2 newly purchased cards and keep running into dead links. The cards I bought are for a CISCO-2801-CCME/K9 with PVDM2-8, FL-CCME-25, SP Services 128F/256D cisco router:
vic3 2fxs/DID and a vic2 2fxo.
I keep finding documents on how to install these cards but all links are dead and leading to nowhere.
http://www.cisco.com/en/US/docs/routers/access/interfaces/ic/hardware/installation/guide/2port_FXS_DID_VIC.html#wp1065062
The 2 documents i'm looking for are: how to install a 2-port vic2 fxo cards on cisco 2801 router and how to install 2-port vic3 2fxs/DID cards on the same 2801 cisco router.
NOTE: I've never installed these cards and am not sure if:
Does my ios support both of these cards?
and which slots do I install those in the router.
I have 4 slots like this:
slot 0: This slot only accepts VIC's ***This could be used for the vic3 2fxs/DID card correct?
slot 1: Nothing written here ****What can i install in this slot?
slot 2: This slot only accepts VIC's and WIC's ***If I buy a WIC and install here which other slot can i install my VIC2-2FXO card in ?
slot 3: Nothing written here ***What can i install in this slot?
Any chance someone can help me out with this.
Thanks very much

Ok
I was able to figure out what goes where and found out that the IOS i had c-2801-spservicesk9-mz.124-15.T10.bin with cme-full-4.1.0.2 tar didn't support the vic3 2fxs/DID card. I then found the one that works which is the c2801-spservicesk9-mz.124-22.YB5.bin.I am now able to see my new hardware interfaces. The question I have now is since the previous version ran with cme-full-4.1.0.2 tar i'm not sure if this needs to be changed since in the compatibility matrix i found this IOS c2801-spservicesk9-mz.124-22.YB5.bin to be compatible with cme-full-7.1.0.0 tar
Do i need to remove cme-full-4.1.0.2 tar and install the cme-full-7.1.0.0 tar?
If yes, i know how to install the cme-full-7.1.0.0 tar but how do i remove the other cme-full-4.1.0.2 tar file in order to be able to install the other version?
Thanks

Vic3-2FXS/DID fax problem

I have a network in Beijing China below,
(1) E1 Pri interface to PSTN
(2) Vic3-2FXS/DID to fax machine
all these modules installed on Cisco 2900, when I call my fax machine from PSTN, the fax machine answered, but fax can't start.
I want to know is there any special consideration about the fax configuration to be worked.
Thanks for your advice.
Robert
2011/2/18

Hey Robert.
Since you have PRI and the fxs port on the same card, in theory there is not a whole lot you need to do with regards to the fax or port configuration on the router if this is H323 or SIP. On our initial voip gateways even on port to port calls we would invoke fax relay, but on the ISR line with the internal tdm backplane, the dsp should be dropped from the call with minimal impairment of the connection through the gateway.
Now, this is true as long as you don't have "no local-bypass' configured under the voice-card. Default is that this is not configured but it you do, you should change it to local-bypass. "show voice dsp active" will show if the dsp is still in the loop on the call as well.
Definitely check the E1 controller ("show controller e1") for slips and errors. This will kill a fax if present.
Looking back at your previous post though, I would not expect you to be seeing G722 on the output of the show voice call summary when the call connects between the two ports.
Are you using MGCP?
When the call is active between the two ports, what is the output of "show call active voice brief" and "show call active fax brief"?
There are a few good resources for troubleshooting fax issues. An excellent source if the CiscoPress publication "Fax, Modem and Text for IP Telephony". If you would like some of the scaled down versions, I have posted a couple of links that would be useful.
Bryan
https://supportforums.cisco.com/community/netpro/collaboration-voice-video/ip-telephony/blog/2010/10/26/fax-configuration-and-troubleshooting-project
http://www.cisco.com/en/US/docs/ios/12_3/vvf_c/voice_troubleshooting/old/vts_fax.html

VIC3-2FXS/DID

Hi everybody,
We have a CCM version 4.x and we need to connect two fax extensions on a VIC3-2FXS/DID card.
The problem is that the faxs are 6 floors up the CCM. Between floors are connected by Optical fiber thought Cisco Switchs. We can configure these faxs on that card?
Thanks!!

VIC3-2FXS/DID
If you have copper pairs to connect, yes.<-- means that if we connect the faxs to a switch and the VIC3-2FXS/DID to the other switch with Ethernet cable it will work?
VIC3-2FXS/DID

2801 can not detect VIC3-2FXS card.

Hi,
I have the 2801 router with a VIC3-2FXS card that is not detecting, I see it with sh diag command like Unkown WAN card.
The IOS that I´m using is:
Cisco IOS Software, 2801 Software (C2801-SPSERVICESK9-M), Version 12.4(15)T7, RELEASE SOFTWARE (fc3)
System image file is "flash:c2801-spservicesk9-mz.124-15.T7.bin"
I checked the details and It can support it.
Do you have any idea what I can do ?.
Thank you, best regards.

Thank you by your support.
Do you know If I can use next IOS:
c2801-ipvoicek9-mz.124-24.T2.bin
Release Date: 22/Oct/2009
Size: 39192.34 KB (40132948 bytes)
Minimum Memory: DRAM:192 MB Flash:64 MB
Thank you, best regards.

Why the ringing voltage closely 0v for VIC3-2FXS/DID port?

Initially, I have tested every port of FXS module on ISR with an analog phone. There
was ringing tone and I was able to communicate to other as normal. The second
test involved measuring the ringing voltage on the same ports by using a pair cable and multimeter. The
'idle voltage' measured was around 44V and when there was an incoming call, the measured 'ringing
voltage' was close to 0V.
So why the ringing voltage is drop to 0V?
Please advice.

You cannot measure ringing voltage with a common multimeter. Read why:
http://www.sandman.com/ringvoltbul.html

Did Wireless Mighty Mouse come with an installation CD?

I love my wireless mighty mouse that I bought with my imac but I want to use it with my newly purchased macbook as well. The only problem is, I can't seem to locate the installation CD that I'm assuming came with it.
The mouse DID come with a CD, correct? Is there anywhere else I can look - drivers embedded in Tiger OSX?
I've called Apple a couple times (on hold as I "speak"). Anyway, they haven't been able to help me too much, I spent 45 minutes last night and I just had to hang up with them and I couldn't get any answers. I will pay for it but I think maybe they're trying to see if they have any available CD's (I would imagine they should have some extras lying around :)!)
Thanks for your help.
Message was edited by: K8TY

You don't need the CD that comes with the Mighty Mouse. All you need to do is go to software update on the Apple menu icon and update your software. If there is any software for the mouse that needs updating, it will update.

VIC3-4FXO/DID module not detect in 2801 Router.

Hi Team,
I have Cisco 2801 router with 2 DSP 16 Channel, 128 MB DRAM and 128 MB flash. I am using IOS c2801-spservicesk9-mz.124-3i but the VIC3-4FXO/DID module is not detected. I tried to upgrade the IOS to 15.0 and 15.1 but the router is not boot up due to insufficient memory. In that IOS the FXO card is detected. I checked the data sheet of both router and FXO card it support 12.4T IOS but when I upload the IOS and try to boot same problem I have faced (router not boot due to insufficient memory). Kindly help me find out the appropriate IOS to resolve the issue.
Thanks in advance.
Regards,
Manas Ranjan

VIC3-4FXO card is not supported in 2801 according to table4
Table 4. Software and Memory Requirements for Voice/Fax Network Modules and Voice Interface Cards
Product
Cisco 2800 Series
Cisco 3800 Series
Cisco 2900 and 3900 Series
NM-HD-1V
NM-HD-2V
NM-HD-2VE
• Cisco IOS Software
• Release 12.3(8)T4
• "IP Voice" images
• Cisco IOS Software
• Release 12.3(11)T
• "IP Voice" images
• Cisco IOS Software Release 15.0(1)M
• "UC Technology" images
VIC2-2FXO
VIC2-4FXO
VIC2-2BRI-NT/TE
• Cisco IOS Software
• Release 12.3(8)T4
• "IP Voice" images
• Cisco IOS Software
• Release 12.3(11)T
• "IP Voice" images
• Cisco IOS Software Release 15.0(1)M
• "UC Technology" images
VWIC2-xMFT-xx
• Cisco IOS Software
• Release 12.3(14)T
• "IP Voice" images
• Cisco IOS Software
• Release 12.3(14)T
• "IP Voice" images
• Cisco IOS Software Release 15.0(1)M
• "UC Technology" images
VIC3-2E/M
• Cisco IOS Software
• Release 12.4(15)XW or 12.4(20)T
• "IP Voice" images
• Cisco IOS Software
• Release 12.4(15)XW or 12.4(20)T
• "IP Voice" images
• Cisco IOS Software Release 15.0(1)M
• "UC Technology" images
VIC3-2FXS/DID
VIC3-2FXS-E/DID
VIC3-4FXS/DID
• Cisco IOS Software
• Release 12.4(15)XZ or 12.4(20)T
• "IP Voice" images
• Cisco IOS Software
• Release 12.4(15)XZ or 12.4(20)T
• "IP Voice" images
• Cisco IOS Software Release 15.0(1)M
• "UC Technology" images

Analog Lines to E1 DID/DOD configuration need for CCME

Dear,
I have one of our remote site have the following configuration:
* 2 X CCME running on C3845.
* 1 X CUE installed on one of the C3845
* Around 70 IPT (7910, 7941 & 7941) registres in the CCME.
* 8 * analog lines connected to FXO ports that provide land lind connectivity for the site.
* 4 * FXS ports to provide FAX.
and becasue of unstability issue with the out/ingoing call we requested 4 X voice E1 DID/DOD. and want to know what is the required configuration to consider in migrating my remote site.
regards

Hello, thanks for your responses helped me very much.
I have the commands and errors completes:
When I enter the command:
ds0-group 0 timeslots 1-15,17-25 type r2-digital r2-compelled ani into the controller e1, I receive this error:
% Not enough DSP resources available to configure ds0-group 0 on controller E1 0/0/0
% The remaining dsp resources are enough for 20 time slots.
% For current codec complexity, 1 extra dsp(s) are required to create this voiceport.
This the inventory in the router:
GW-VOSS(config-controller)#do sh inv
NAME: "2821 chassis", DESCR: "2821 chassis" PID: CISCO2821         , VID: V05 , SN: FTX1336AHFS
NAME: "VWIC2-1MFT-T1/E1 - 1-Port RJ-48 Multiflex Trunk - T1/E1 on Slot 0 SubSlot 0", DESCR: "VWIC2-1MFT-T1/E1 - 1-Port RJ-48 Multiflex Trunk - T1/E1" PID: VWIC2-1MFT-T1/E1 , VID: V01 , SN: FOC133129NF
NAME: "2nd generation two port FXO voice interface daughtercard on Slot 0 SubSlot 1", DESCR: "2nd generation two port FXO voice interface daughtercard"PID: VIC2-2FXO         , VID: V02 , SN: FOC13332NDZ
NAME: "3rd generation two port FXS DID voice interface daughtercard on Slot 0 SubSlot 2", DESCR: "3rd generation two port FXS DID voice interface daughtercard" PID: VIC3-2FXS/DID     , VID: V01 , SN: FOC132526S0
NAME: "PVDMII DSP SIMM with four DSPs on Slot 0 SubSlot 4", DESCR: "PVDMII DSP S IMM with four DSPs" PID: PVDM2-64          , VID: V01 , SN: FOC13341ZE1.
I have the transcoding:
dspfarm profile 1 transcode
codec g711ulaw
codec g711alaw
codec g729ar8
codec g729abr8
codec g729r8
codec g729br8
maximum sessions 15
associate application SCCP
I have CUCM 7.0, Contac Center 6.0, SIP trunk, 1 E1.
I need another PVDM card? The router can be have two PVDM card? Which PVDM card you recommend ?
Regards

G3 Modem and ATA Controller Card

I am upgrading a B&W G3 350 MHz Yosemite running Tiger for some friends. They use dial-up (pooh) and the B&W did not ship with an internal modem. I found an Apple OEM on welovemacs.com for $60 ($10 more than the Apple USB). I am not sure which route to go (internal or USB). I am in a timed situation, so I am also considering a PCI modem. Any suggestions on the PCI modem (brand and model)? I know Tiger will not support some PCI modems.
Also, the G3 will not support larger HDDs. It currently has a 40 Gig drive in it. I tried installing an 80 Gig, but the ATA controller chip (Rev 1 logic board) did not recognize it. Any suggestions on a PCI based ATA controller card (brand and model)? Also, do these ATA controller cards usually ship with the power and data cables, or do I need to buy them separately? If so, any suggestions on which ones to buy and where?
I would appreciate any help as quickly as possible.
Thanks,
Thomas

Grant,
"Only when you start to use them do you begin to notice more than a casual amount of crashes, lock-ups, and eventually, data corruption. An 80 GB hard drive should be recognized immediately if it is correctly cabled and the straps are set correctly. Both 80 GB and 40 GB drives may be encountering corruption problems on the built-in controller."
The 40 GB drive has been in this machine for at least 4 years. It was originally my machine given me by a Mac Genius buddy. I used it for over a year before I bought my G4. I then loaned the B&W to my cousin who used it for over 2 years before HE bought a G4 and returned the G3 to me.
When I installed the 80 Gig drive (which already had 10.3 installed), the machine would not boot from it. I booted from the Tiger install DVD and tried to install Tiger. The installation got all the way to the end, then the installation seemed to stop. I left the machine sit for about an hour, then heard the boot tone of the machine re-starting. It never booted, though. I got the gray Apple screen and could actually hear the "Welcome to Tiger" music coming from the speaker, but the gray Apple screen never went away.
I tried re-jumpering the drive, thinking I had gotten the jumper opposite of what it should be, but that didn't do any good either. I tried putting the drive in my Granite Digital external Firewire HDD casing, but the drive would never mount on my G4. So, I re-re-jumpered the drive back to the way I originally had it jumpered. It mounted on my G4 just fine at that point. So, I then installed Tiger via the external Firewire casing using my G4 tower. Tiger installed successfully, and I put the HDD back into the G3, but it STILL would not boot. It would never get past the gray Apple screen, or the machine would kernel panic if it did.
So finally, in desparation, I put the old 40 Gig that was in the machine when my cousin shipped it back to me, back into the G3 and it booted from it just fine. I later did a clean install of Tiger, and the machine still boots fine.
So, as you can see, it really seems that the ATA controller chip does not like the 80 Gig drive.
"Why not broaden your options with an external modem?"
I may indeed decide to go with the Apple external USB, but was told by a Specialist at the Apple Store that the new Apple USB modem might not work with the G3. My friend, whose parents I am setting the G3 up for, owns a MacBook Pro, so he can use the Apple USB if it does not work with the G3 and when and if his parents get broadband.
I still would like to know if a PCI based modem will work with the the G3. I found a post on this board late last night (after I posted this thread) where a user had a question similar to mine. He/she was trying to swap a PCI modem between a PC and a B&W. Whoever responded to the post stated that the B&W will not support ANY PCI based modems. It will only support the OEM Apple modem that plugs into the logic board near the USB and Firewire ports or an external USB modem (similar to, but not specifially the Apple USB modem).
Thanks,
Thomas

Failing HD's or is problem the main ATA bus

OK i'll try to give all the facts and keep this post as short as possable
I have G4 sawtooth? dual 1 gig with 3 hard drives, the 80 gig seagate that came with the G4 connected to the main ATA bus and about a year ago i added a 120 gig Maxtor as slave along with another Maxtor drive 80 gig i added as slave to the CD/DVD drive. Up to a couple of weeks ago no problems.
I leave my computer on at all times.
Both drives connected to main ata bus both drives running Tiger10.4.7
and the third OS 9.2.2
the problem started if i needed to restart for any reason, upon booting back up 1 or the other did not show up, checked all the connections, even using a new ata cable.... no change, just a restart would cause one or the other not to appear never to the the 3rd drive.
The problem keep happining more freqently, getting to the point that both drives would not appear, so it only booted off the OS 9 drive.
Ran disk utility on both drives
Checking the slave drive with 4 partitions never indicated any problems,
A few weeks ago the Master drive{Seagate) gave me 2 errors, "could not unmount drive" same thing using Techtool, i could not verify permmisions, "no valid packages found"
The drive still operated fine.
Now yesterday both drives would not show up and would only boot off the OS 9 drive.
Spent most of the night trying anything i could think of
One last thing struck me, I coneccted the OS 9 drive as master and pluged it into the main ata bus, you guessed it that drive did not boot,
after that i connected the other two drives to ata bus that the CD?DVD drive was connected to and upon starting up both drives are up and running fine so far (still got the same error messesages off the same drive as before).
So what am i dealing with here, i think there is a problem with the main ata bus.
So as of now im up and running with only 2 drives,
the third drive and the CD?DVD pluged into the main bus do not show up.
Well i think i covered everything, now anybody got any ideas on what's happining with the main ata bus, can't take it out to fix it, my only source of income is disability so paying someone is out of the question!
What to do?
Thanks for reading this now i await to hear from you.
sknoxx
Sawtooth G4 desktop duel 1gig Mac OS X (10.4.7)

is this what i need
I need a ide pci controler card with an ata133 interface
can i keep the drives i have internal
i m going to buy another HD 250 gig, now that will have to be external
right?
will the sawtooth model give me all 250 gigs
will the drive transfer data quicker than the iniernal drives
how many drives can be connected
i already have a pci usb card so i don't want usb or firewire
does it have to be mac only or will a pc card work as well
im in Hawaii so i would rather buy it here to avoid shipping costs
is this what i need?
this is at compusa for $40
Overview for
StarTech.com Dual Channel Serial ATA PCI Controller Card
(Based on manufacturer's information)Make the jump to Serial ATA performance with a two-port Serial ATA controller card from StarTech.com. The PCISATA provides your system with two independent Serial ATA ports for connecting internal Serial ATA devices like hard drives, CD-ROMs, CD-RWs and DVD drives.
Cutting-edge Serial ATA connectivity at the fraction of the cost of a new motherboard, the PCISATA2 is compatible with both Windows® and Linux® operating system environments and is backed by our lifetime warranty and FREE lifetime tech support.
Features
Compliant with PCI Specification V2.2
Compliant with Serial ATA Specification V1.0
High-speed data transfer rates of up to 150 MBytes/sec
Two independent Serial ATA channels support one Serial ATA device on each channel
Controller Type: SATA
Slot Type: PCI
Port Connectors:
2 x SATA Female
are any of rhese what i need?
EIDE ULTRA ATA-133/100 PRO CONTROLLER FOR MAC
Price Range: $55.87-79.99
Manufacturer: SIIG Inc. Part number: SCMP4A12
Information on EIDE ULTRA ATA-133/100 PRO CONTROLLER FOR MAC
Full specs
User opinions
Manufacturer info
Compare with most popular
Full specs
General
Device Type
Plug-in card
Type:Interface Type
PCI
Localization
English:N/a
Expansion / Connectivity
Expansion Slot(s) Total
1 PCI
Port(s) Total (Free) / Connector Type:Port(s) Total (Free) / Connector Type Port(s) Total (Free) / Connector Type
2 2 for PC connection Storage ATA-133 40 pin IDC Male 2 Internal Installed
Expansion Bay(s) Total
None
Expansion / Port(s) Required
Slot(s) Required
1 PCI
Port(s) / Connector(s) Required
None
Bay(s) Required
None
Software / System Requirements
Operating system
Apple MacOS X, Apple MacOS 8.6, Apple MacOS 9.x
Storage Controller
Storage Controller Supported Device Type:Supported Device Type
CD drive, Hard drive
Storage Controller:RAID Level
N/A
Data Transfer Rate
133 MBps
Storage Controller:Controller Interface Type
ATA-133
Max Storage Devices Qty
4
Controller Interface Type:Channel Qty
2
Miscellaneous
Package type
Retail
Warranty
Service / Support Details
Limited warranty Parts and labor 5 years Bring-in
Power
Power device type
None
sknoxx
Message was edited by: Steve Knox

Voice card not appaering in configuration?

we have inserted pvdm3 module in to the 2901 router
but its LED status is showing Amber continuolsly.
I would like configure the VIC3-2FXS/DID card but I am not able to see the card in running configuration but I could see the card in sh diag.
Can any ony help?
Its sh diag command giving the following output.
/#sh diag
Slot 0:
        C2901 Mother board 2GE, integrated VPN and 4W Port adapter, 4 ports
        Port adapter is analyzed
        Port adapter insertion time 00:58:11 ago
        EEPROM contents at hardware discovery:
        PCB Serial Number        : FOC16310CSA
        Hardware Revision        : 1.0
        Part Number              : 73-11834-09
        Top Assy. Part Number    : 800-30795-05
        Board Revision           : A0
        Deviation Number         : 0
        Fab Version              : 03
        Product (FRU) Number     : CISCO2901/K9
        Version Identifier       : V05
        CLEI Code                : CMMHB10ARA
        Processor type           : C1
        Chassis Serial Number    : FGL16312126
        Chassis MAC Address      : 6073.5c26.7440
        MAC Address block size   : 72
        Manufacturing Test Data : 00 00 00 00 00 00 00 00
        EEPROM format version 4
        EEPROM contents (hex):
          0x00: 04 FF C1 8B 46 4F 43 31 36 33 31 30 43 53 41 40
          0x10: 06 17 41 01 00 82 49 2E 3A 09 C0 46 03 20 00 78
          0x20: 4B 05 42 41 30 88 00 00 00 00 02 03 CB 8C 43 49
          0x30: 53 43 4F 32 39 30 31 2F 4B 39 89 56 30 35 20 D9
          0x40: 04 40 C1 CB C2 C6 8A 43 4D 4D 48 42 31 30 41 52
          0x50: 41 09 C1 C2 8B 46 47 4C 31 36 33 31 32 31 32 36
          0x60: C3 06 60 73 5C 26 74 40 43 00 48 C4 08 00 00 00
          0x70: 00 00 00 00 00 F3 00 65 40 01 25 41 00 87 42 00
          0x80: 00 F8 00 28 03 E8 1C 89 07 D0 20 21 0B B8 20 93
          0x90: 0F A0 21 2F 13 88 21 83 17 70 21 A8 1B 58 21 B0
          0xA0: 1F 40 21 AB 23 28 21 79 27 10 21 78 41 01 1D 42
          0xB0: 00 00 F8 00 28 03 E8 1C 20 07 D0 1F 40 0B B8 20
          0xC0: 6C 0F A0 21 34 13 88 21 34 17 70 21 98 1B 58 21
          0xD0: 98 1F 40 21 98 23 28 21 34 27 10 21 34 FF FF FF
          0xE0: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
          0xF0: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
        PVDM Slot 1:
        16-channel (G.711) Voice/Fax PVDM3 DSP DIMM PVDM daughter card
        Hardware Revision        : 1.0
        Part Number              : 73-11576-03
        Board Revision           : C0
        Deviation Number         : 0
        Fab Version              : 03
        PCB Serial Number        : FOC162257KD
        RMA Test History         : 00
        RMA Number               : 0-0-0-0
        RMA History              : 00
        Processor type           : 00
        Product (FRU) Number     : PVDM3-16
        Version Identifier       : V01
        EEPROM format version 4
        EEPROM contents (hex):
          0x00: 04 FF 40 05 D8 41 01 00 82 49 2D 38 03 42 43 30
          0x10: 88 00 00 00 00 02 03 C1 8B 46 4F 43 31 36 32 32
          0x20: 35 37 4B 44 03 00 81 00 00 00 00 04 00 09 00 CB
          0x30: 8F 50 56 44 4D 33 2D 31 36 20 20 20 20 20 20 20
          0x40: 89 56 30 31 20 D9 02 40 C1 FF FF FF FF FF FF FF
          0x50: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
          0x60: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
          0x70: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
        WIC Slot 0:
        3rd generation - FXS DID Voice daughter card (2 port)
        Hardware Revision        : 1.0
        Top Assy. Part Number    : 800-30501-02
        Board Revision           : A0
        Deviation Number         : 0
        Fab Version              : 07
        PCB Serial Number        : FOC1350420M
        RMA Test History         : 00
        RMA Number               : 0-0-0-0
        RMA History              : 00
        Product (FRU) Number     : VIC3-2FXS/DID
        Version Identifier       : V02
        CLEI Code                : IP9IAB3CAB
        Longitudinal Calibration : 01 10 10 4F 8D 10 10 8F
                                   9F
        EEPROM format version 4
        EEPROM contents (hex):
          0x00: 04 FF 40 06 21 41 01 00 C0 46 03 20 00 77 25 02
          0x10: 42 41 30 88 00 00 00 00 02 07 C1 8B 46 4F 43 31
          0x20: 33 35 30 34 32 30 4D 03 00 81 00 00 00 00 04 00
          0x30: CB 8D 56 49 43 33 2D 32 46 58 53 2F 44 49 44 89
          0x40: 56 30 32 20 D9 02 40 C1 C6 8A 49 50 39 49 41 42
          0x50: 33 43 41 42 D3 09 01 10 10 4F 8D 10 10 8F 9F FF
          0x60: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
          0x70: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
Embedded Service Engine 0/0 :
Total platform memory : 524288K bytes
Total 2nd core memory : 0K bytes
Start of physical address for 2nd core : 0x80000000
Virtual address start of 2nd core memory : 0x0 - 0x0
2nd core configured disabled
L2 cache ways for 2nd core : 0
Its sh running-conf command giving the following output.
/#sh running-config
Building configuration...
Current configuration : 1228 bytes
! Last configuration change at 06:29:29 UTC Fri Feb 7 2014
version 15.1
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
hostname /
boot-start-marker
boot-end-marker
enable secret 4 tnhtc92DXBhelxjYk8LWJrPV36S2i4ntXrpb4RFmfqY
no aaa new-model
no ipv6 cef
ip source-route
ip cef
multilink bundle-name authenticated
crypto pki token default removal timeout 0
license udi pid CISCO2901/K9 sn FGL16312126
hw-module pvdm 0/1
username cisco
interface Embedded-Service-Engine0/0
no ip address
no ip route-cache
shutdown
interface GigabitEthernet0/0
ip address 172.169.2.152 255.255.255.0
duplex auto
speed auto
interface GigabitEthernet0/1
no ip address
duplex auto
speed auto
ip forward-protocol nd
no ip http server
no ip http secure-server
control-plane
line con 0
line aux 0
line 2
no activation-character
no exec
transport preferred none
transport input all
transport output pad telnet rlogin lapb-ta mop udptn v120 ssh
stopbits 1
line vty 0 4
password cisco
login
transport input all
line vty 5 15
password cisco
login
transport input all
scheduler allocate 20000 1000
end
and sh flash giving me the following output.
/#sh flash
-#- --length-- -----date/time------ path
1     74503236 Jul 30 2012 20:08:54 +00:00 c2900-universalk9-mz.SPA.151-4.M4.bin
2         2903 Jul 30 2012 20:21:54 +00:00 cpconfig-29xx.cfg
3      3000320 Jul 30 2012 20:22:10 +00:00 cpexpress.tar
4         1038 Jul 30 2012 20:22:18 +00:00 home.shtml
5       122880 Jul 30 2012 20:22:26 +00:00 home.tar
6      1697952 Jul 30 2012 20:22:40 +00:00 securedesktop-ios-3.1.1.45-k9.pkg
7       415956 Jul 30 2012 20:22:54 +00:00 sslclient-win-1.1.4.176.pkg

Thank you Gergely Szabo,
Sh Inv output and sh version output is as follows.
/#sh inv
NAME: "CISCO2901/K9 chassis", DESCR: "CISCO2901/K9 chassis"
PID: CISCO2901/K9      , VID: V05 , SN: FGL16312126
NAME: "3rd generation two port FXS DID voice interface daughtercard on Slot 0 SubSlot 0", DESCR: "3rd generation two port FXS DID voice interface daughterca"
PID: VIC3-2FXS/DID     , VID: V02 , SN: FOC1350420M
NAME: "PVDM3 DSP DIMM with 16 Channels on Slot 0 SubSlot 5", DESCR: "PVDM3 DSP DIMM with 16 Channels"
PID: PVDM3-16          , VID: V01 , SN: FOC162257KD
NAME: "C1941/C2901 AC Power Supply", DESCR: "C1941/C2901 AC Power Supply"
PID: PWR-1941-2901-AC , VID:    , SN:
/#show version
Cisco IOS Software, C2900 Software (C2900-UNIVERSALK9-M), Version 15.1(4)M4, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2012 by Cisco Systems, Inc.
Compiled Tue 20-Mar-12 18:57 by prod_rel_team
ROM: System Bootstrap, Version 15.0(1r)M15, RELEASE SOFTWARE (fc1)
/ uptime is 3 hours, 22 minutes
System returned to ROM by power-on
System restarted at 08:40:55 UTC Mon Feb 10 2014
System image file is "flash0:c2900-universalk9-mz.SPA.151-4.M4.bin"
Last reload type: Normal Reload
This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.
A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html
If you require further assistance please contact us by sending email to
[email protected].
Cisco CISCO2901/K9 (revision 1.0) with 483328K/40960K bytes of memory.
Processor board ID FGL16312126
2 Gigabit Ethernet interfaces
1 terminal line
2 Voice FXS interfaces
DRAM configuration is 64 bits wide with parity enabled.
255K bytes of non-volatile configuration memory.
250880K bytes of ATA System CompactFlash 0 (Read/Write)
License Info:
License UDI:
Device#   PID                   SN
*0        CISCO2901/K9          FGL16312126
Technology Package License Information for Module:'c2900'
Technology    Technology-package           Technology-package
              Current       Type           Next reboot
ipbase        ipbasek9      Permanent      ipbasek9
security      None          None           None
uc            None          None           None
data          None          None           None
Configuration register is 0x2012

Cisco FXS Port - RJ11 to RJ45

Hi,
I have a VIC3-2FXS/DID in Switerzland and my customer has asked for it to be connected to a fax machine through Strucuted cabling and they would like to know what type of cables they required.
They want RJ11 (FXS Port) to RJ45 (Patch Panel) then RJ45 (Patch Panel) to RJ11(Fax Machine).
Could someone explain the pins out of the cables, as it is going to be two RJ11 to RJ45 cables do they need to rollover?
Thanks for any help.

All cabling on Cisco voice cards is straight through from the port to the device. RJ11 has 2 pins, for tip and ring. That's blue and white/blue. RJ45 has 8 pins, but if you want to stick with the 568B wiring standard on the RJ45 jacks,you would use this.
Blue: RJ11(pin1)----RJ45(pin 4)--------(pin4)RJ45-----(pin 1)RJ11
White/Blue: RJ11(pin2)----RJ45(pin 5)--------(pin 5)RJ45-----(pin 2)RJ11
If you actually have RJ14 jacks (4 pins), its pins 2 and 3 (the middle pins) which are used. If it is RJ25, it's still the middle pins, which would be 3 and 4.

Central recording server using MTP at remote

I am getting ready to implement a voice recording solution. We will be using auto recording / RTP forking. We will have centralized recording servers and wish to transcode the G.711 recording streams to G.729 using MTP on the remote site voice gateways. I am trying to calculate the required DSPs for this solution. I can see our current MTP max sessions when I configure the MTP, but I don't know if this equates to a 1 for 1 for recording sessions. There will be two recording streams in the same direction, remote to HQ this includes the agent and customer streams. Does anyone know how many MTP sessions are used per recording session?
I would assume it would be 1 MTP session per normal bi-directional call, but not sure with both streams going in the same direction for the recording sessions.
Thanks,
Mark

I have g711ulaw and g729r8 configured. There is a mix of 2811 and 2911 voice routers. This is a typical config.
Show inventory:
NAME: "CISCO2911/K9 chassis", DESCR: "CISCO2911/K9 chassis"
PID: CISCO2911/K9      , VID: V02 , SN: FTX1533AN65
NAME: "VWIC2-1MFT-T1/E1 - 1-Port RJ-48 Multiflex Trunk - T1/E1 on Slot 0 SubSlot 0", DESCR: "VWIC2-1MFT-T1/E1 - 1-Port RJ-48 Multiflex Trunk - T1/E1"
PID: VWIC2-1MFT-T1/E1 , VID: V01 , SN: FOC15240VK1
NAME: "3rd generation two port FXS DID voice interface daughtercard on Slot 0 SubSlot 1", DESCR: "3rd generation two port FXS DID voice interface daughtercard"
PID: VIC3-2FXS/DID     , VID: V03 , SN: FOC15273DM3
NAME: "3rd generation two port EM voice interface daughtercard on Slot 0 SubSlot 2", DESCR: "3rd generation two port EM voice interface daughtercard"
PID: VIC3-2E/M         , VID: V02 , SN: FOC15297W3H
NAME: "PVDM3 DSP DIMM with 64 Channels on Slot 0 SubSlot 4", DESCR: "PVDM3 DSP DIMM with 64 Channels"
PID: PVDM3-64          , VID: V01 , SN: FOC153013MW
NAME: "C2911 AC Power Supply", DESCR: "C2911 AC Power Supply"
PID: PWR-2911-AC       , VID: V03 , SN: DCA1522R1GX
Thanks,
Mark

ATA vs VG202 vs VIC3-2FXS-E/DID & Wireless

Similar Messages

Maybe you are looking for