Atheros AR9285 driver problem, connection problem

Hi
Downloaded the latest HP Assistant today. This utility scanned my probook and suggested several updates, including and update for my Qualcomm AR9285 wireless internet connection. After this update I lost my wireless connection. I had the same issue a few weeks ago, where I ended up reinstalling the probook to factory settings. The wireless network worked again after this prolonged operation!
I have tried several different drivers from fx atheros.cz but nothing seems to solve the problem. How can HP recommend and update that makes your laptop wireless fail - I'm puzzled! Router is a Cisco EPC3925.
Any suggestions to solve this would be appreciated.

This is the answer I sent as reply to the Case: 4650970052, which apparently had been closed down before I could make a response....
Thank you for your email.
I have solved the issue with the corrupt driver for Atheros AR9285 802. 11b/g/n WIFI Adapter which I downloaded and installed via the HPSA recommended updates.
I eventually had to reinstall the 4535s to it's factory settings and the WIFI connection is now working again. The only driver that seem to work is the original 9.2.0.412 dated 21-04-2011.
I have also removed the HPSA utility so it will not happen again! It's very time consuming to reinstall. Even if you only keep a very limited number of software utilities on the laptop. E.g. it took almost 18 hours just to do the Window 7 updates.
But thanx for trying to be helpful.
Best regards
Stephen Canham

Similar Messages

Atheros WLAN Driver Fixes Connection Issues With Many New Routers (Linksys, Netgear, D-Link, etc...)

Hi:
This post is for those that have the below listed Atheros adapters, and recently upgraded their routers (usually from a Wireless G to a Wireless N router from 2009 or newer), only to find they cannot connect to the internet anymore.
Atheros AR5006 802.11a/b/g WiFi Adapter
Atheros AR5007 802.11b/g WiFi Adapter
Atheros AR5009 802.11a/g/n WiFi Adapter
When using their old equipment, there were no problems.
Symptom: When upgrading to a new router, normally connection is made to the local network, but one cannot access the internet.
Symptom: Wireless connects if using WEP security or no security, but will not connect when using WPA2-Personal security.
For those who have the above Atheros wireless adapters, and are experiencing issues with connecting to the internet, there is a driver available that should remedy the situation.
It is good for Windows operating systems -- Windows XP through Windows 7 -- 32 or 64 bit.
It may work on Windows 8 too, but I haven't tested it on Windows 8.
Here is the link to the driver download page:
http://h20564.www2.hp.com/hpsc/swd/public/detail?sp4ts.oid=5060881&swItemId=ob_108905_1&swEnvOid=405...
Best Regards,
Paul

I created an HP account just to thank you for this link. I've spent 2 days online and talking to call centers trying to get this driver. I was finally going to just return my router to Best Buy. Thank you SO much!

I-net oranxo driver problem. cannot connect

Hi, im new to the j2ee programming communitty and i was trying to use the i-net type 4 driver to connect to an oracle database. The service name of the oracle database is orcl. i know that the host is the local host, and im pretty sure that the port number is 1521. i dont think i changed it. unfortunately i dont know how to change it. if you could tell me a way to change it once i have already installed it, i would appreciate it.
my code for this problem is
import java.sql.*;
public class testDB{
public static void main(String args[])
     new testDB();
testDB()
     try{
          Connection con = DriverManager.getConnection("jdbc:inetora:localhost:1521:orcl", "scott", "tiger" );
          new com.inet.ora.OraDriver();
          CallableStatement cstmt = con.prepareCall("{call procone(?,?,?)}");
          cstmt.setInt(1,6619211);
          cstmt.setString(2,"Java");
          cstmt.setInt(3,22);
          cstmt.execute();
          con.close();
          }catch(Exception x){
                    System.out.println("exception: "+x);
the error its giving me is the following
com.inet.ora.ORA3SQLException: [OraDriver] Connection Refused:Connect
Anyone know why theres a problem. im sorry i know its probably a dumb question but i cant figure this out.

re: Oracle database and listener:
Oracle does not do things in a simple way. I'll explain things using Oracle's terminology (which I didn't use earlier).
To Oracle, the collection of data-storage (files or devices) that actually has the data is the "database", without regard to any program code or running process.
To Oracle, the memory structures and process (or threads on some OSes) normally used to access a database is called an "instance". (In casual speech, most people call the "instance" the "database"; usually the distinction doesn't matter).
You can have a database without an instance (the program isn't running), an instance without a database (the database hasn't been created or you're using a special Oracle feature called ASM), or you can have multiple instances for one database (an Oracle RAC cluster).
You cannot connect directly to an Oracle instance via a TCP/IP connection (which is normally what a JDBC driver will use, although there are other ways). Instead, Oracle has another program, called the "listener" that brokers connection requests; your program talks to the listener on port 1521 and the listener arranges for your program and the database to connect. The database might actually be on another computer but almost never is, except with RAC clusters or failover configurations. So the listener has to be running for most JDBC programs to work.
SQL*Plus can connect to a database instance via TCP/IP, which requires the listener; however, SQL*Plus can also connect to a database instance that is on the same computer via inter-process communication, which does not require the listener. Stopping the listener process and connecting via SQL*Plus is a common way of putting a database into "maintenance mode", where only the database administrator can make changes to the DB.
The standard Oracle installation will install everything and set up the listener and have it autostart on boot and everything else needed. However, people sometimes disable things they think they don't need, so it's not unheard of for people to turn off the listener becaus they think they don't need it. Or sometimes there's an error and the listener fails to start...

HT4759 I had to change my apple password to fix hard drive problem in my iPhone and now I cannot connect date stored in iCloud as my password has changed. How do I plug in new password to iCloud to be able to retrieve data from my MacBook Pro to my I pho

If you change your apple password how do you notifly icloud to resync everything? Forgot my apple password, had to change it due to hard drive problem on my iphone 4 which had to be totally erased then rebouted and now works but cannot download from my computer/icloud due to password change. So how do I orchestrate the change of password to icloud/computer to allow all to sync together?

If you use Lion, boot into your recovery pressing Command and R buttons, press "Utilities" menu, open Terminal and write:
resetpassword
If you have Snow Leopard, boot into your install DVD pressing C button, click "Utilities" and press Password Reset

Hard drive problem...... Please Help

Hard drive problems
I am sure it is due to my error or mistake but I received a new Maxtor III touch as a replacement for my failed drive yesterday after connecting it I went to Maxtor one touch manager software that came with it and the drive did not appear in the window so then I opened disk utilities and copied my notebook hard drive over to the Maxtor ran permissions on each drive and then closed down my system ! today when I opened my Powerbook with the Maxtor on it gave me the grey screen 2x so I disconnected the Maxtor ran permissions again and everything was fine until i power up the Maxtor and Grey screen again! Help How do I fix this?????

Maxtor one touch III firewire 800 its connected to my Titanium G$ Powerbook I am beginning to think its just another drive failure

Satellite T230D PST4LA-00R008 Atheros AR9285 WiFi / BT driver issues

Hello,
I have replaced HDD in satellite T230D pst4la-00r008 due to HDD failer.
i have tried win 7 x86 sp1, win8 and 8.1 x64 and am currently setting up win 7 x64 sp1,
i have installed all drivers as recomended by toshiba and cant connect to wifi or install bluetooth.
adaptor is an atheros AR9285. (installed wifi (from toshiba, MS and atheros websites) followed by BT driver filter followed by monitor and then BT Stack).
wifi drivers install ok and wifi networks are available but cant connect no error message.
when installing bluetooth stack it asks me to plug in bluetooth device.
will post more info as i organise all errors/crashes from different OS driver combinations.
could some one please advise me what the default windows and driver are for the laptop in reagrds to WIFI as the sticker on the bottom has been rubbed away.
thank you in advance

Hi
I found the specification of the Atheros AR9285 chip and this miniPCI Wlan card does not support BT
http://www.qca.qualcomm.com/wp-content/uploads/2013/11/AR9285.pdf
_*AR9285 Specifications*_
Frequency Band: 2.4 GHz
Network Standard: 802.11b, 802.11g, 802.11n
Modulation Technology: OFDM with BPSK, QPSK, 16 QAM, 64 QAM; DBPSK, DQPSK, CCK
FEC Coding: 1/2, 2/3, 3/4, 5/6
Hardware Encryption: AES, TKIP, WEP
Quality of Service: 802.11e
Media Access Technique: CSMA/CA
Communications Interface: PCI Express
Peripheral Interface: GPIOs, LEDs
Supported Data Rates: 11b: 1 - 11 Mbps 11g: 6 - 54 Mbps 11n: 6.5 to 150 Mbps
Operating Voltage: 1.2V +/-5% 3.3V +/-10%
Package Dimensions: 8 mm x 8 mm
Package: 68-pin LPCC

Windows 7 - HP Laserjet 8500 print driver problem

I have tried everything imaginable to correct this HP 8500n print driver problem with no success, please help!
I cannot correct or get rid of a reoccurring “Incompatible Print Settings” error dialog box message that repeatedly states that “There are one or more conflicting settings. One of the settings is: Output Bin: Mailbox 1, Accessory Output Bin: Not Installed”. The radio button options are “Restore my previous settings or Keep this setting, and I will change it later”. This same dialog message repeats 13 times for all the other various conflicts each time you click on printer properties to change to 2 sided printing or any other printer settings. This printer does not have any of these features attached or set into it.
I am a volunteer that manages a number of computers on our small church LAN, 2 computers operating on MS XP-SP3, 2 on MS Windows 7 Home Premium and my 2 problem computers that came pre-installed with Vista Home Premium of which I have performed an HP OEM upgrade to Window 7.
I have isolated this print driver problem to the Vista operating system and even when computers are upgraded to Windows 7 does not correct this driver error. I have also tried every possible print driver variant of the HP 8500, HP8550, PCL, PS to include the Microsoft versus HP versions with no success. In each case I get this error yet neither of the XP computers or the computers that had Windows 7 as a original operating system have no problems with their print drivers for this printer.
Yes, I have repeatedly searched and upgraded the operating system and print drivers. In desperation I have even tried to find the correctly behaving Windows 7 print driver and transfer it to these Vista upgraded to Windows 7 machines. However I could not isolate the driver location.
The only thing I can conclude is that this errant HP print driver was resident within Vista and remains resident even after a HP OEM Windows 7 upgrade. Additionally, all of these computers are configured to access this printer via its static IP address on the network. The XP computers are 32 bit, all of the Vista upgraded to Win 7 and OEM Win 7 computers are 64 bit machines all with respective OS.
Can anyone please help me correct this problem?

Hi,
Unfortunately I can't see your uploaded image yet as it is awaiting approval from HP.
From what I can see you are correct that HP does supply drivers for this printer and that the drivers for your printer are already included with Windows 7. On the machines affected, try the procedure below to see if it helps at all
Next download revo uninstaller on the link below and install it.
http://www.revouninstaller.com/download-freeware-version.php
Disconnect the printer from the PC.
Run Revo and see if it finds any HP Printer Software installed. If it does, right click the software icon and select uninstall. During the process you may be asked to delete registry entries. If you are, just select all and click delete. Do the same for any left over files and folders. Once completed, reboot the PC.
Re-connect your printer to the PC and follow the guide below.
http://h20000.www2.hp.com/bizsupport/TechSupport/Document.jsp?&objectID=c02536257
If this helps you will need to repeat the process on each of the affected machines.
Best wishes,
DP-K
****Click the White thumb to say thanks****
****Please mark Accept As Solution if it solves your problem****
****I don't work for HP****
Microsoft MVP - Windows Experience

Update ODBC Access driver Problem??

I am trying to update fields in a tab pane.I already have add and delete functions working but on Trying upate I get a Microsoft Driver Exception Notice [Microsoft][ODBC Microsoft Driver].Why ??
Here some code:
final static String driver = "sun.jdbc.odbc.JdbcOdbcDriver";
final static String url = "jdbc:odbc:addBKTAFE";
final static String table2 = "Address";
String sql = ""; // Used to store sql statements
int pane_number = 0; // Used to indicate what screen needs to be processed
//--------------------Start updateRecord()-------------------------------------->>>
// Update personnel details.
void updateRecord() {
try {
// load MS Access driver
Class.forName(driver);
// Setup connection to DBMS
Connection conn = DriverManager.getConnection(url);
// Create statement
Statement stmt = conn.createStatement();
sql = "UPDATE"+
table2 +
"SET "+
"FirstName ='" + tfFirstName2.getText() + "'," +
"LastName ='" + tfLastName2.getText() + "'," +
"Address ='" + tfAddress2.getText() + "'," +
"City ='" + tfCity2.getText() + "'," +
"State ='" + tfState2.getText() + "'," +
"Postcode='" + tfPostcode2.getText() + "'," +
"Country ='" + tfCountry2.getText() + "'," +
"EmailAddress='" + tfEmailAddress2.getText() + "'," +
"HomePhone='" + tfHomeNumber2.getText() + "'," +
"FaxNumber ='" + tfFaxNumber2.getText() + "'," +
"WHERE person_id =" + cbPersonId2.getSelectedItem().toString();
stmt.executeUpdate(sql);
conn.close();
JOptionPane.showMessageDialog(null, recupdated,
information,
JOptionPane.INFORMATION_MESSAGE);
} catch (Exception ex) {
JOptionPane.showMessageDialog(null,
ex.getMessage() + ex.toString(),
genexception,
JOptionPane.INFORMATION_MESSAGE);
//--------------------End updateRecord()---------------------------------------->>>

I would suggest the following put in
System.out.println(sql);
right after the creation of the statement to look at it when it is complete.
It is hard to see any other errors the way it appears in the forum.
You can then copy it and try it exactly the way it is in assess and see if it
works there.
This may help find the problem.
You can put in the following statement to see the sql logging.
Note I have never tried it - it may show you the problem.
java.sql.DriverManager.setLogStream(java.lang.System.out);
Two other things - as I do not use access the comma is not
standard in SQL.
- what is in the fEmailAddress2 - is there any special
characters that may be causing a problem - try i
with blank field.
rykk

Lenovo Drivers Insufficient for update to 8.1 - Driver problem - H430

Lenovo Drivers Insufficient for update to 8.1 - Driver problem (USB?) - H430
my lenovo H430 is about 6 months old - worked okay with preinstalled Windows 8
After update to Windows 8.1 computer no longer seemed to work well at all, although I am unable to provide hard evidence, but clearly it was not working as smoothly as in the previous 8 version with lots of irritating little problems - including sound.
One thing that very clearly was not functioning as it had in 8 version was the USB disconnect icon. In 8 you only had to click on icon and the USB selection window would open immediately. Additionally all USB connections would be shown - back and front USB. Select the USB to be disconnected and it would be disconnected immediately (providing not in use). After update to 8.1 this was no longer the case.
In 8.1 disconnect icon no longer worked as it had done in 8. After clicking on icon there was now always a lengthy pause, followed by the sound of the computer working (whirring sound) and then after a while the USB selection window would finally open. Sometimes it was necessary to click on icon a few times to get any reaction at all. A small MP3 player I had charged up on my computer every morning (front USB) in windows 8, was always in USB list, and disconnected without problem in 8. In 8.1 it was no longer in list and only charged sporadically (would stop charging, but if I clicked on USB icon it would start charging again - although still not shown in USB list).
After about two weeks of 8.1 my screen suddenly - but only briefly - went black twice. I ran a sfc /scannow. problems were found but could not be resolved. I did a Dism /Online/Clean-Image/RestoreHealth this was reported as being successful. About two days later my computer went into blue screen BSOD - "critical-services-failure" - from which I was unable to get out of. The only option open was the Lenovo restore option. Computer was returned to factory state with los of all data.
back to Windows 8 the computer once again worked okay - no problems - and USB icon once again worked correctly (including with MP3 player).
About 2 weeks later after receiving MS messages to update to 8.1 I called Lenovo support and asked about update to drivers for 8.1.
the following list was given:
Chipset: Intel chipset Driver for Windows 8.1 (64-bit) Version : 9.4.0.1022
Video: CPP2 AMD DISCRETE VGA CARD DRIVER for Windows 8.1 (64-bit) Version: 13.152
Audio: Realtek Audio Driver for Windows 8.1 (64-bit) Version: 6.0.1.7030
LAN: Realtek Lan Driver for Windows 8.1 (64-bit) Version: 8.018.0621.2013
STORAGE: Intel RST Driver for Windows 8.1 (64-bit) - Desktop Version: 12.8.0.1016
I updated to 8.1 and then updated all the above drivers (no USB driver update was available).
The same problems as the last update to 8.1 and USB was as bad as it was in last 8.1
Some days later my computer went into blue screen BSOD once again - although this time did not stay stuck there, and quickly restarted - due to speed of restart I did not get time to read all the text and discover the cause of BSOD.
Computer is still running badly - particularly the USB icon disconnect.
Called Lenovo support but they have been no help!!!!!!!!!!!!!!
Lenovo are failing us with the 8.1 update and the DRIVERS FOR 8.1
BSOD
all i could find was this: (probably refers to after BSOD - the restarting part after BSOD???)
<Event xmlns="http://schemas.microsoft.com/win/2004/08/events/event">
- <System>
<Provider Name="Microsoft-Windows-Kernel-Power" Guid="{331C3B3A-2005-44C2-AC5E-77220C37D6B4}" />
<EventID>41</EventID>
<Version>3</Version>
<Level>1</Level>
<Task>63</Task>
<Opcode>0</Opcode>
<Keywords>0x8000000000000002</Keywords>
<TimeCreated SystemTime="2013-12-20T08:12:33.642341400Z" />
<EventRecordID>9644</EventRecordID>
<Correlation />
<Execution ProcessID="4" ThreadID="8" />
<Channel>System</Channel>
<Computer>myleno</Computer>
<Security UserID="S-1-5-18" />
</System>
- <EventData>
<Data Name="BugcheckCode">209</Data>
<Data Name="BugcheckParameter1">0xb8</Data>
<Data Name="BugcheckParameter2">0x2</Data>
<Data Name="BugcheckParameter3">0x0</Data>
<Data Name="BugcheckParameter4">0xfffff8000020170a</Data>
<Data Name="SleepInProgress">0</Data>
<Data Name="PowerButtonTimestamp">0</Data>
<Data Name="BootAppStatus">0</Data>
</EventData>
</Event>

I have now seen the suggestion by Tomaspoko and Brillow at http://forums.lenovo.com/t5/ThinkPad-Edge-S-series/Windows-8-1-update-S440-ThinkPad-black-screen-wit...
Despite the AMD driver giving an error during install at the last stage of the suggested fix, this has now yielded a working switchable graphics for my S540 for the first time with Windows 8.1. Catalyst Control Center also works for the first time, so thank you to both the above-mentioned posters for a solution that does work.
Hopefully in time AMD will release a non-broken updated AMD driver and CCC package.
Thanks again for a nice solution from this forum - the problem was driving me nuts!

I have lost my info for my ipod due to hard drive problem. Can I upload the info on my ipod to my computer. I don't want to lose what is on my ipod.

Lost ipod info on computer due to hard drive problem. Can I upload info on ipod back to my computer and how do i do it.

- Transfer iTunes purchases by:
iTunes Store: Transferring purchases from your iPhone, iPad, or iPod to a computer
- Transfer othe music by using a third-party program like one of those discussed here:
Best iPod to PC
- Create a backup of the iPod by connecting the iPod to the computer. Right click on the iPod under Devices in iTunes and select Back Up.
- Restore the iPod from thzt backup and sync a necessary.

Print driver problem with OS 10.4.6

I recently installed 10.4.6 and ever since have been unable to print via a network on a Lexmark Optra T614 (duplex). All was working fine until the upgrade to 10.4.6. I have downloaded a driver from Lexmark's website and successfully installed it to my system via the wizard - message was "you have successfully installed . . . ". However cannot find it to install through the Print Centre. I am running it through a router shared with a PC (Windows 2000). No problems at the Pc end. As I said prior to purchasing 10.4.6 all was working fine. I have tried to set up to print through the local network via the PC - without success. At one point (not sure what I did) actually got the Mac talking to the printer. The lights were activated and it made a few attempts but then cancelled out. I then tried something else and it didn't work, so now I am back to where I was when I started. Can you help with this one Greg? regards Ian

Hi Greg, Still no answer to my printing problem.
The Optra T driver is probably right.
I trashed the drivers and did a fresh download and reinsatlled. It is an Optra T driver.
Since you can't print using generic postscript, I don't think you
have a driver problem. If the printer supports LPD or
IPP, you probably need to enter a device queue name
in Printer Setup. (No queue name for HP Jetdirect
protocol) L1, P1, LPT1, and print are common queue names
I have set up so that Printer Name is 192.168.0.200. This automatically selected Lexmark Optra T. Also the queue name appeared as 192_168_0200-1. Host name was blank and Driver Version 10.4 and PPD File Version is 10.4.3.3.0. I tried to print the Print box showed Preparing . . then Processing Page 1 and dissapeared in the normal manner. I opened the Printer Monitor (in the dock) and it showed the job in the queue as it should and the Status showed: printing. The blue bar scrolls and the message Connected to 192.168.0.200 comes up. The printer shows no sign of receiving the file. I have done this numerous times. I have also keyed in the computer name in the location and still no go - just the same outcome. The computer name is ian-brownlees-computer.local.
Look in the printer manual or google for it.
Unfortunately I don't have a manual but have been trying to locate one.
Any further clues??

Thunderbolt to Firewire 800 external drive problems

I recently upgraded from a MacBook Pro 17" early 2011 to a MacBook Pro Retina 15" (early 2013). I have a Drobo and two Seagate 4TB external drives, all connected via Firewire 800. So, I added a Thunderbolt to Firewire 800 adapter and, it seemed, life was good.
I keep my large iTunes Movie and TV show collection on the Drobo. Since transitioning to the new MacBook, I have had a number of issue with watching movies on my Apple TV 3. Randomly, and periodically, the movie appears to be corrupted - the audio track skips/loops and the image is horrible macroblocked, as if the file is damaged. When I check the movies on the Drobo, opening it with Quicktime on the MBP, it plays just fine at the same spot it appeared damaged on the Apple TV 3.
A second symptom is this: I can no longer re-encode video with Handbrake with the source and target files on the Drobo - it gets some portion of the way through and it just stops, leaving the video partially encoded; again, at random locations/offsets into the video and not the same spot twice.
My initial thought is that connection to the Drobo is dropping out and coming back, on its own, but long enough to cause the above problems.
Is anyone else seeing this issue or something related when using the Thunderbolt to Firewire 800 adapter with large drives?
Thanks, in advance.

Update: I exchanged the Thunderbolt to Firewire adapter and the issue persists. I have a Drobo that I used with my previous system, a PowerMac G5, and never had any issues like this.
It does not matter what software I use. But at some point video playback will suddenly become garbled. If I start the video from the beginning, sometimes the garbled video will start sooner but never later. A restart temporarily resolves the issue. If I copy the file to the local hard drive the video will play back garbled. This is indeed a very strange issue. The issue behaves like a bandwidth bottleneck.
I was having this issue prior to upgrading to Mavericks.
Fred K
iMac (Late 2012), 3.4 GHz i7, GTX 680MX, Fusion Drive, 24 GB RAM, Drobo (Firewire via Thunderbolt)

Help! folder icon w/ exclamation point - hard drive problem?

I live in the philippines and the store which i called up said the only solution is to show the receipt and they will send it to singapore but i still have to buy a new one. it's like they're not giving me choices at all. i know my iPod is not yet "dead", why do i have to buy a new one? how can i have this repaired?! it hasn't been a year yet, but around 10 months already and i don't have the receipt anymore.
here's what happened...
for the past week my iPod has been skipping songs, going to the next ones but doesn't play at all. sometimes it even freezes. and i hear this whirring sound at the back.
so i decided to connect it to the computer and erase all my songs first coz i thought maybe the problem was with the files. but iTunes didn't recognize the device. so i decided to reset it (so that the songs and my factory settings will be erased) by pressing menu and select at the same time. then after i did this the "do not disconnect" message kept on showing up and eventually it just stayed there. so i tried resetting again. the apple logo shows up but after a while the folder icon with exclamation point shows up. then it would turn off.
I tried restoring it with updater but it says it could not mount the ipod. so this might be a hard drive problem already. how can i solve this?
please help!

Try calling their toll free number <probably charges apply when you're calling outside the US>, 1-800-827-0685.
Usually, they will send your machine to the nearest repair station. I think in SEAsia, repair stations are in Malaysia.
Your iPod comes with a universal warranty, so you could definitely have that repaired even without the receipt. <Im from the Philippines too. I what you mean...>
good luck!=D

Nokia N8 installing driver problem !! HELP ME !!!!

Hi guys, i recently bought a Nokia N8.
i've install Nokia Ovi Suit from folder that exist in my phone, it's completely install ovi suit and download Nokia N8's USB driver from internet and stores it in "C:\Program Files\Nokia\Connectivity Cable Driver".
when i connect the phone in Nokia Ovi Suit Mode via USB, windows can found it, but cannot install its drivers !!!
Windows says that: "Windows found driver software for your device but encountered an error while attempting to install it.
The service cannot be started, either because it is disabled or because it has no enabled devices associated with it." (i use Windows Vista 32-bit, see below attachment)
what can i do ??!!! plzzzzz help me i need too run Ovi Suit !!!
Attachments:
Nokia N8 USB Driver Problem.jpg ‏138 KB

I am having the exact same issue.
The Ovi store was installed first via the N8 built in software, then uninstalled and reinstalled using the latest Ovi version from Nokia's webinstaller download, but still no success with the Ovi connection.
The other file transfer modes work fine 'media transfer & 'mass storage' but the Ovi store is still unable to run due to Windows VISTA not being able to locate the drivers for the N8 software. (despite being installed!)
After accepting the prompt for Windows to locate the drivers... The same error as RayMond_021 screen shot appears.
"COMPUTER SAYS.... NO!"
Super frustrating! A brand new $800 phone and I can't even access the promised software (Ovi maps) that encouraged me to buy it!?
PLEASE HELP US!!!!!

Oracle JDBC driver problem for Oracle 8.1.6

i am a newbee to Java, i was trying JDBC programming thru Jbuilder 4.0. now the problem is whenever i am trying the DriverManager.getconnection(), I am getting an error "NO SUITABLE DRIVER". i have downloaded jodbc14.jar(oracle 9i JDBC driver) but so result. what can i do now? any other config issues or is it due to absence of a Oracle JDBC driver of Oracle 8.1.6.

i have set the classpath as mentioned. but no solution.
the error is like this::
java.lang.NoClassDefFoundError: java/sql/Savepoint
     at java.lang.ClassLoader.defineClass0(Native Method)
     at java.lang.ClassLoader.defineClass(ClassLoader.java:486)
     at java.security.SecureClassLoader.defineClass(SecureClassLoader.java:111)
     at java.net.URLClassLoader.defineClass(URLClassLoader.java:248)
     at java.net.URLClassLoader.access$100(URLClassLoader.java:56)
     at java.net.URLClassLoader$1.run(URLClassLoader.java:195)
     at java.security.AccessController.doPrivileged(Native Method)
     at java.net.URLClassLoader.findClass(URLClassLoader.java:188)
     at java.lang.ClassLoader.loadClass(ClassLoader.java:297)
     at sun.misc.Launcher$AppClassLoader.loadClass(Launcher.java:286)
     at java.lang.ClassLoader.loadClass(ClassLoader.java:253)
     at java.lang.ClassLoader.loadClassInternal(ClassLoader.java:313)
     at oracle.jdbc.driver.OracleDriver.getConnectionInstance(OracleDriver.java:521)
     at oracle.jdbc.driver.OracleDriver.connect(OracleDriver.java:325)
     at java.sql.DriverManager.getConnection(DriverManager.java:517)
     at java.sql.DriverManager.getConnection(DriverManager.java:177)
     at DbaseTest.DbaseForm.OpenConnection(DbaseForm.java:37)
     at DbaseTest.DbaseForm.jbInit(DbaseForm.java:73)
     at DbaseTest.DbaseForm.<init>(DbaseForm.java:26)
     at DbaseTest.Application1.<init>(Application1.java:11)
     at DbaseTest.Application1.main(Application1.java:40)
i have imported
import java.awt.*;
import java.awt.event.*;
import javax.swing.*;
import java.sql.*;
import oracle.jdbc.*;
import java.lang.*;
the driver is registered by:
DriverManager.registerDriver(new oracle.jdbc.driver.OracleDriver());

Atheros AR9285 driver problem, connection problem

Similar Messages

Maybe you are looking for