[Athlon64] K8T Neo-FIS2R RAM Question

Hi All
At the moment I have 512mb of Corsair 3200 RAM (2x 256) in a MSI K8T Neo-FIS2R, and I was wondering if it would be ok to put another 1gig of non Corsair in with out it going nuts at me.
Thanks for any help.

Many thanks for the help.

Similar Messages

MSI K8T NEO-FIS2R: RAM problems

I have the motherboard K8T NEO-FIS2R with AMIBIOS 2VMS V2.0 010505.
I tried these DDR-RAM:
DDR-RAM 512MB PC400 CL3 Kingston KVR400X64C3A/512
DDR-RAM 512MB PC400 CL3 Samsung
but the motherboard recognizes only 256 MB for both. The RAM are good: I tried them in an other pc!
Now I have installed an A-DATA ram 256 MB and the motherboard recognizes 256 MB!
Do you think that my motherboard is defective?
Thank you in advance.
P.S. I'm sorry for my bad english.

No the memory controller is onboard the CPU so in any case the MB is not defective. However the CPU revision may hold you back on some RAM especially if you mix make and model RAM on the same channel. A socket 754 CPU only has one channel so all RAM must be matched to work properly.
If those Sticks can only be seen as a wrong value when used by themselves it is likely that either they have errors or the timings in Bios are improperly set to azllow them to work. In this case you can normally find out what is going on by running memtest86. If you get errors on test 5 or 7 then you have timgs timed improperly and any other errors would show bad RAM.
Another case is not having enough power for everything to work properly together. Usually this happens when you don't have enough 12v amps for these newer rigs.
Post complete specs and test results and maybe we can help you further.

[Athlon64] K8t Neo FIS2R V1

Hi. Trying to set up a K8T Neo FIS2R V1.0 with an AMD Sempron 2800+. When I hit the power button it powers up for 1 second then dies. The green light on the tower flashes and manual says CPU overheat. Checked cpu is seated ok, checked RAM ok. If I unplug the 4 pin power connector the cpu fan then runs ok but nothing else works. Tried different video card, diffrerent RAM, different PSU. I have cleared the bios as stated but problem still exits. Could I have a faulty board? Thanks

You should use at least bios version 2.0, which if i remember correctly is the first one with support for semprons. I recommend 2.1, 2.2 causes some problems with agp aperture size on 256mb.
I don't see any other possibility than getting a "normal" amd 64 processor and then update your bios (of course it would be unnecessary to install the sempron then, because normal 64's generally perform better).

MSI K8t Neo FIS2R RAID Question

I've just put together my new system. If it weren't for this forum, I might not have succeeded. Thanks for all the info out there.
Currently, I'm running raid 0, using (2) raptor 74's. The next thing I want to do is mirror. I bought a 160 gig maxtor ata drive for this purpose. But, after seeing the table in the MSI raid manual, it looks like I have to use (2) drives the same size as the raptor 74's inorder to use the raid 0+1 configuration. Any help on this would be apreciated.
MSI K8t Neo FIS2R
Athlon 64 3200
Kingston (2) 512mg Hyper X DDR500
Western Digital 74 gig Raptors (2) raid 0
Nvidia Geforce Ti 4200 128mg graphics
shydragon

but mirror raid wont save you from oc crash's , virus, bad installs, acidently, deleteing or any useful recovery..it only protects from hd failure to mechanical or electrical malfunction.
you are far better off imagine the drives or mking backups, and using the drives as storage for that, you will come out ahead.
but if you still want raid 1, you can
partition the drives?
use the smaller ones for system restore , and internet cache, mp3's . for example
for rich performance freaks buy 2 more satas and raid them on the other chip
just a few ideas

K8t Neo-fis2r - not booting!!!

Hello Motherboard gurus! Any help would be appreciated...
Here are my system specs:
AMD Athlon 64 3000+
Motherboard /AMD Socket 754 CPU’/ "K8T NEO-FIS2R"
RAM - Kingston 184 Pin 512MB DDR PC-3200 X2
Hard Drive – 120GB – Maxtor 120GB 6Y120PO
TEAC 1.44MB 3.5 Black Floppy Disk Drive
ThermalTake Silent PurPower 360WATX Power Supply
Lite-on DVDR – Model LDW/811S/851s BLK
ATI AIW RADEON 9600 Video Card, 128MB DDR, 128-bit, CATV/Video Out/Video In, 8X AGP, Model "ALL-IN-WONDER 9600"
Everything was working just fine until I switched out my CPU fan for a super quiet Zalman fan. I hit the power and nothing, but the fan spins up just fine. No video. The LED's on the back cycle through a couple of settings and sit at all green except for the upper left at red. I am at a loss ...perhaps the video card? I tried replacing the original fan and got the same result
Thanks in advance for any help,
JD

Your power is weak for sure. However you may also be seeing a fan that runs to slow for the motherboard to read. If the speed drops below what the MB expects it will cause issues as it thinks the CPU fan is dead and may not want to operate at all. Check that by reinstalling your old fan. Also on the power issue what is the 12v rail amps on that PSU?

K8T Neo-FIS2R - 3200+ - Mushkin Level 1 RAM: Optimal Memory Settings

Just got a K8T Neo-FIS2R with a AMD Athlon 64 3200+ with 1g (512MB X
2) Mushkin Level 1 PC3500 RAM as recommended by Anandtech on his High
End System roundup:
www.anandtech.com/guides/showdoc.html?i=2041
I am having a HUGE problems with memory settings in the BIOS.
On AUTO, the memory is only autodected at DDR200, which I found odd.
I them took memory setting in my old hands and things don't seem much
better:
I made these changes:
MEMCLOCK: DDR400
BANK INTERVEAVING: AUTO
BURST LENGTH: 8 BEAT
CL: 2
TRCD: 3
TRAS: 5
TRP: 2
This was unstable at first and bumped the DDR Voltage to 2.7, moved
the sticks to DIMM1 and DIMM3 (instead of DIMM2), and it seems stable,
but not very fast. according to Sandra Scores
Any recommendations for Memory Settings? Why would the MB not
autodecte DDR400 RAM? I am not looking to overlock...just maximize
the CPU and memory I have.
Maybe I just need to get new memory. What is the best memory for this motherboard?
Thanks,
Steve

I'm running the same mem (see my sig). Since its PC3500 I attempted to tighten the settings to those you had listed (2,3,2,5). It was not Prime95 torture test stable at even the stock 200 MHz FSB using these settings. Upping the voltage to 2.7 did not increase the stability in my system at these settings. The memory ran perfectly at AUTO settings, but was clocked at 2.5,3,3,8 I believe.
Keep in mind that level 1 is advertised at 2,3,3. My system is 100% stable at 2.7V for me up to 210 MHz FSB at these settings (I haven't tried any faster). My TRAS is set to 6.
Hope this helps a fellow Mushkin user

MOVED: K8T Neo-FIS2R SATA and Linux Question

This topic has been moved to Operating Systems.
K8T Neo-FIS2R SATA and Linux Question

Quote
Originally posted by chasmon
Hi all,
I have just setup up a brand new system but am having probelms getting it working. I want to install XP on a single Maxtor 160Gb drive.
I have my HD on Promise Ser1 and all SATA stuff in BIOS enabled. When I get to the screen I press F6 and then when promted I insert the floppy with the promise drivers on. I then get this message:
"File txtsetup.oem caused an unexpected error (4096) at line 1742 in d:\xpclient\base\boot\setup\oemdisk.c"
I can't get past this screen I have tried:
1.Drivers from the CD supplied.
2.Drivers from the MSI website.
Please help me this lot cost lots of hard earned I'm pretty gutted at the moment. I have also tried the Via chipset with no joy.
System:
Antec 380W PSU and Sonata Case
LG DVDROM 8163B
NEC DVDR/RW 2500B
Panasonic Floppy
Neo FIS2R mobo
Maxtor Diamondmax Plus 9 160Gb SATA150
Benq RF K/B & Mouse
Don't spam man! I posted something to this same question in another thread.. from you no less! Make a new thread! lol
Hijacking = bad!
Ian

K8T Neo-FIS2R Hard drive configuration questions

Im looking to buy this board in maybe a month or less (K8T Neo-FIS2R), and was wondering about configuring hard drives
I will get the version which has the promise controller on board, fo SATA RAID
The Plan is to get two Wetern Digital Raptor drives and put them in RAID 0 together.
however i will still have my DVD Writer, removeable hard drive bay (takes one IDE) and my current 80GB Seagate drive.
if i use the SATA RAID, do i have to use IDE3 for all the other devices, or can i just plug them into the IDE1 and IDE2 slots?
Also you are able to select SATA to boot from in bios correct? i have never done raid so have no idea how it works . and do you have to load RAID drivers or something before setting up windows?

anyone?

[Athlon64] MSI K8T Neo FIS2R BIOS Update when? CnQ no workie!

The MSI K8T Neo FIS2R (MS-6702) hasn't had a BIOS update since 3-4-2005!
I put a Sempron 64 3000+ in my motherboard, and was very disappointed that it is recognized as an "AMD Unknown Processor". Sure, it works, but one of the reasons I bought it is in the hopes of getting AMD Cool n Quiet to work. However, apparently the AMD driver can't recognize the CPU due to the old BIOS on the motherboard.
Every other MSI skt 754 board supports Sempron E6 revision already. Why not the K8T Neo FIS2R? Where have all the MSI BIOS programmers gone? I have been waiting 2-months for a BIOS update to support the E6 Semprons. I have asked and begged MSI Tech Support. I am tempted to switch to ASUS or some other company that is actually timely with BIOS updates. Only reason I haven't yet, is this board is everything I want EXCEPT for Cool n Quiet not working. It's starting to look like there is no BIOS update in sight, so I am very disappointed.
Anyone here work for MSI can confirm there are no plans for a BIOS update? Because I don't want to wait around for something that's not going to happen.

Sorry, I didn't mean to imply I thought the mods here are MSI staff... I was just kind of hoping there's MSI staff lurking here, seeing what people think of their products or seeing what people complain about.
No, pretty much C 'n Q is the only reason I'm disappointed, but it was something I was really set on getting to work since this is a server that's up 24/7, but isn't utilized but maybe 4hrs out of a given day. I could reduce frequency and voltage, but unlike C 'n Q, it won't automatically increase speed and voltage based on demand - which is something I want since although it's a server, I also use it as a regular PC as well.
I've even tried the 2.33 beta BIOS with no change, and even found a 5.52 BIOS in their BIOS testing directory. I guess that BIOS was for a different kind of 6702, although I had pulled out the peripheral modules with AMI's MMTOOL and they looked the same as the existing BIOS, but that BIOS killed my motherboard so it couldn't have been for a regular 6702. I had to desolder the BIOS chip with a heat gun, reprogram the old BIOS back on it with an EPROM programmer, and solder in a socket. I guess that shows my dedication to get C 'n Q working!

K8T Neo-FIS2R/FSR no POST

I have a K8T Neo-FIS2R/FSR (MS-6702) which is, along with all my other components (I'll list them later), over a year old. It has been running just fine until the other day. I have not modified any hardware or BIOS-settings recently.
The day before yesterday my speakers put out a high-pitched shriek and the screen turned black. I then turned off the computer (it seemed to still be running, fans spinning). As I switched it on it let forth 8 beeps followed by a paus, and then 8 beeps again, over and over. I switched the graphics card for another one, no difference.
I then left it turned off for a few minutes. Then I booted it up again, and voila, it worked fine. Then after a few minutes it died the same way, and when I rebooted it it started beeping again.
Switching graphics card doesn't help. I powered it on without a graphics card plugged in. Then it made 8 beeps, and then silence. The cycle was not repeated, as it was when the card was in.
I then used another motherboard, another CPU and other RAM, same graphicscard and harddrive, and it boots into Windows just fine and seems to be quite stable for the day I've tried it.
I then switch back to the K8T-motherboard with it's CPU and RAM (still same graphicscard and harddrive as the other one), and it boots fine. After almost an hour it dies again. On boot, beeps. Wait a few minutes, boots again, then dies. Beeps next time. Etc.
The 8 beeps apparently mean there is a problem with the video card. I have tested two video cards that both work fine on another motherboard, no difference.
Because it dies after a while when it has rested, I suspect some sort of overheating issue. I put a bigass fan blowing at the motherboard and video card but that didn't seem to do anything. The fan on the video card is clean.
I have hooked up the D-Bracket 2 that accompanied the motherboard. It has some lights flashing depending on what is going on, and it halts on "Early Chipset Initialization", which is phase 2 of 16 (1st being "System Power ON"). When I press the power button, the LEDs on my memory sticks flash for a few seconds (showing activity), and the D-Bracket lights up. Then the memory-LEDs go to rest (inactivity), and the D-Bracket halts. Fans keep spinning but there is no life. No beeps.
After leaving the computer off for the night, I cleared the CMOS. The computer booted and ran fine for a couple of hours, then it suddenly made a noise in the speakers, and the monitor went black. Fans still spinning. The little light at the monitor indicating that it is turned on was flashing, as it does when the computer is off and the monitor is on.
This is the hardware in my system at the moment. I have removed plenty of stuff to rule out other components but even with just this it won't work. No mouse, keyboard or other drives attached, just this.
CPU: Athlon64 3200+
Memory: Corsair TWINX1024-3200XLPRO DDR
Power: Thermaltake Purepower Butterfly 480W W0020
Output: +5V (35A), +3.3V (28A), +12V (17A), -5V (0.3A), -12V (0.8A)
Graphics: Gainward GeForce 6800Ultra 256MB GDDR3 AGP8X, "Ultra/2600 Golden S",
Motherboard: K8T Neo-FIS2R/FSR (MS-6702)
Harddrive: Seagate Barracuda IV ATA 7200 RPM
Monitor: Samsung SyncMaster 957p
Any ideas, suggestions or questions? I am stumped.

Quote
I have removed plenty of stuff to rule out other components but even with just this it won't work.
Quote
Graphics: Gainward GeForce 6800Ultra 256MB GDDR3 AGP8X, "Ultra/2600 Golden S",
Quote
+12V (17A),
If your graphics card is like mine (see sig) with two power connections at the back you may have stressed the PSU over the last year to it's final end. Borrow or buy another PSU with at least 24 amp on the 12v supply. Your current PSU with only 17 12v amps was bound to fail. Especially since you state you had other hardware at one time. CPU Graphics card, case fanes and drives are all calling on the 12v rail to power them and your PSU just might not have it any more to do the job and the highest draw is at startup.
Try another PSU.

K8T Neo-FIS2R / Kingston KVR400X64C25/256

As a first time poster my apolgies if this has been covered elsewhere - I have read most of the posts on this forum but found no specific reference. Please just point me in the right direction if i am wrong!
I bought the Kingston KVR400X64C25/256 modules because:
a) they were listed by MSI on the list of tested Ram
b) they were on Kingston's list for the K8T NEO &
c) they were in stock. However...
If installed in DIMM 2 & 3 (as per MSI tested RAM pdf) the system crashes on trying to load Windows. DIMM 1 & 2 'works' if that allows for 8 or 9 restarts/day. I tried 1 & 3 to see if that improved the situation, but if anything it was worse. I have tried increasing the RAM voltage to 2.6 but there is no discernable difference. Upping the TRCD to 4 makes little or no difference.
Memtest86+ initially found no errors (16 hrs/93 passes) but when left running for a week came up with 10 errors (8 in test 6, 2 in test 4). MemTest (http://hcidesign.com/memtest/) gives me an average of 10 errors for 300% pass.
I'm now trying running the memory at 2.7v (within Kingston's ±.25v range).
In the meantime, has anyone run this memory without any problem - i.e. is it a simple case of faulty memory? Equally, has anyone had similar problems and found a solution?
thanks
MSI K8T Neo-FIS2R
AMI rev 1.2
AMD Athlon64 3000+ AMD heatsink/fan (working temp around 32°C)
2 x Kingston KVR400X64C25/256 (DIMM 1, DIMM 2)
NVidia GeForce3 driver v53.03
Antec TruePower 430W +3.3V 28A, +5V 36A, +12V 20A. Max load 410W
IDE1 ST340016A (master) ST320014A (slave)
IDE2 MSI DVD-ROM D16 (MS-8216)
Soundblaster Live 5.1 platinum
Windows XP Pro Version 2002 service Pack 1

Quote
Originally posted by Bas
Hi,
Sorry to say, but as soon as you get errors in memtest, no matter after how many hours, you need to try other memory.
As your memory seems to be unstable....errors in memtest are a NO-NO
hmmm! What if memtest, Prime95 etc. detect no problem over lengthy periods when sticks are individually tested in DIMM1 - as well as the system not crashing once - , but boot failures/memory dumps etc. abound when same sticks are individually placed at 2 or 3? Is this still a memory issue?
For what it's worth I have found Kingston's technical support more than helpful.
MSI K8T Neo-FIS2R
AMI rev 1.2
AMD Athlon64 3000+ AMD heatsink/fan (working temp around 40/42°C)
2 x Kingston KVR400X64C25/256 (DIMM 1, DIMM 2)
NVidia GeForce3 driver v53.03
Antec TruePower 430W +3.3V 28A, +5V 36A, +12V 20A. Max load 410W
IDE1 ST340016A (master) ST320014A (slave)
IDE2 MSI DVD-ROM D16 (MS-8216)
Soundblaster Live 5.1 platinum
Windows XP Pro Version 2002 service Pack 1

Msi k8t neo fis2r odd post issues

well, i went over to a friends house, pulled out his ram..put in in my computer..it posted and boot to windows..perfectly..
so then i go into the bios and up the voltage..so that i can put my old ram back in..it stopped responding when i updated the bios becuase it set the voltage back down to default..so..
i put my ram back in once the voltage is set to 2.75 v and it booted a few times perfectly..i unhooked everything and came home..well
now i try to boot the pc and once again it will not boot? is it possible that the cmos got cleared when i unplugged the pc???
i know my ram isnt bad..i ran it on a friends system while playing games for hours..this motherboard is driving me insane..someone really dropped the ball when they made these..so many issues with having to fool around with voltages etc..cant even get the damn system to post if the voltage isnt up and even then sometimes it seems to not want to ..its crazy..
i know none of my components are NOT broken because ive stresssed them all fully in other peoples computers..
if anyone has any clue as to how i can get this thing to post to get back in the bios plz reply..im at wits end
my system specs are
athlon 64 3000+
512mb mushkin special 2-2-2 ram (i will change the timings to the recommended slightly delayed timings but i have to actually get into the bios to make this possible)
msi k8t neo fis2r bios 1.4

Southmike is sooooooooo right on that one. I see a lot of folks running stuff on other computers with + results and then nothing on the Athlon64 - equipped systems. Well, I think it's O.K. to a certain point, at least to find out if an item is not defunct. But, most of the problems are RAM and PSU related. After that, I believe the BIOS is the biggest issue. And I think some of our forum readers don't actually understand the settings they mess with. I for one, do not fully understand a few of them myself! That is why it's important to make changes in BIOS one at a time.....if you are not as experienced as a lot of folks here at the forum are.

MSI K8T Neo FIS2R- Corsair Twinx XMS4000

Two weeks ago I have bought one MSI K8T Neo FIS2R with an AMD Athlon64 3200+.So far I used the computer with one DIMM of 256MB DDR PC2100 memory. This morning I have installed in the motherboard a pair of CORSAIR TWINX XMS4000 which comprises of two DIMMs of 512MB DDR 500MHz memory.
The computer did never worked again. As soon as I have turned it on, although the whole system got power the screen was blank and the motherboard did not boot. Moreover, the D-Led system of the motherboard has all its leds red which according to the manual means that the processor is probably damaged.I have never overclocked my system and before install the memory it worked perfect. I have disconnected the whole computer but the problem still exists. Can you advise me what I have to do to fix it? What is the cause of the problem? Is there any way so that I can fix it?

Quote
Originally posted by karinio
Two weeks ago I have bought one MSI K8T Neo FIS2R with an AMD Athlon64 3200+.So far I used the computer with one DIMM of 256MB DDR PC2100 memory. This morning I have installed in the motherboard a pair of CORSAIR TWINX XMS4000 which comprises of two DIMMs of 512MB DDR 500MHz memory.
The computer did never worked again. As soon as I have turned it on, although the whole system got power the screen was blank and the motherboard did not boot. Moreover, the D-Led system of the motherboard has all its leds red which according to the manual means that the processor is probably damaged.I have never overclocked my system and before install the memory it worked perfect. I have disconnected the whole computer but the problem still exists. Can you advise me what I have to do to fix it? What is the cause of the problem? Is there any way so that I can fix it?
Hi dude i had identical problem, bought i extra stick 512 400 ddr and the system wont start. Make sure your motheoard support the made of ram. In my case Asus did not support corsaire. Also it could be the slots which are damage.
bye

New K8T Neo FIS2R won't post

I have looked at all the other threads in this forum, but can't find the solution.
Specs:
New K8T Neo FIS2R
New A64 3000+
New Mushkin 3500 Level One (Cas 2) 2x512MB
New Antec 550 (24A on the 12V)
ATI Radeon 9800 Pro
When I give it power, all the fans come on, the 4 LEDs on the bracket stay lit up, and then don't change, but I get no video or any other indications (such as beeps). The 4-Pin power connector, is securely connected in the proper location. The standard ATX connector is also secure. I'd link to a picture to prove it, but my camera is charging right now.
Currently I have only power wires, power switch, system speaker, video card, and 1 stick of RAM in the first slot. I have tried it without the video card, without RAM, with RAM in different slots, just about any combination I can think of. I have even cleared the CMOS a few times. Nothing changes, I always get stuck with the 4 LEDs. I don't have anything connected to the USB headers either (that was mentioned in another post).
I know some people have mentioned that the Antec 550's 24A on the 12V isn't great, but it should be more than enough amps, the way my system is setup right now.

Hi
It does not sound like a major prob, it sounds like a PSU or memory problem, anyway of checking MOBO with another PSU with at least 20A on the 12v. Also check the memory sticky at top of the posts and see if your OK memory wise, another possibility is that one of the mounting screws is tracking from the board - try removing screws and see if it boots, also check none of the cables are touching the case or MOBO.
MOBO and CPU seem fairly resilent, so faulty parts are not to likely, although one never knows. Another thought the Jbat1 Cmos jumper is on pins 1 & 2, 1 is marked on board, and you could try clearing CMOS. a corrupted bios could also cause this.
Best of luck, lets know how you go
Jocko
PS. looking at the stickys at top, Bas has put one there about a compitition by MSI, one of the questions is about Radeons needing extra power( has an April 1st entry date!!), it is worth checking, does your Radeon have its own supply, you could always remove it and see if it boots.
Cheers

K8T Neo-FIS2R - won't post.

Hello friends,
specs:
K8T Neo-FIS2R
Athlon64 3200 (retail with fan)
two 512mb stick Corsair
1 36 gig SATA Raptor WD hdd
1 80 gig SATA WD hdd
Antec 430 w "TruePower" PSU
ATI 9600 pro
Sony optical drives.
Mitsumi 3.5"
buncha Antec fans.
So I got my new baby all put together and took a deep breath and started it up.
All the fans came on, hdds making hdd type noises, CPU fan a-spinning.
Nothing happens. Doesn't post. No video at all. The MSI usb/diagnostics dongle has all 4 LEDs shining, and supposedly that means the CPU is damged or not seated right.
Poop.
So I take it down, pull of the heatsink and look at the CPU. Looks good. Just to be sure I take it out, look for dust or damage or any abnormalities. Nothing. No physical defects on the CPU pins or the socket. Alright. I carefully put the CPU back, put the heatsink back on (Am I the only one who loves how the heatsink attaches? Bravo AMD!) and.....the same thing happens. I sigh loudly and commence with the near hysterical swearing. Girlfriend announces she HATES it when I build a new PC.
Tried all sorts of other premutations, one stick of ram, unplugging all periphs in different combos, pressing the power button while petting a monkey and eating fire. You name it, I've done it. Does anyone else abuse couch pillows?
You gotta let it out man.
I've probably inserted a few hundred CPUs into ZIF sockets over the years, so I'm 100% certain I didn't muss it up.
So before I RMA these little sweethearts (both the mb and cpu, because how can one tell if it's the socket or cpu?) has anyone else been down this road and want to give me the magic cure? Or maybe just a hug?
Much Thanks to you. Have a good weekend.

Hello Friends,
The Hynix dimms in several arrangements, no go.
I also, uh, borrowed some infineon from work. Tried in several configs, no go.
Samsung no go.
Enter: Despair.
As I sat and stared at the machine in sort of a "I just spent a lot of money and what do I have?" sort of way, mine eyes did fall upon the gleaming brand new Antec "TruePower" psu.
Mind you, I had a perfectly acceptable 450 watt. No problems at all with it. It was generic and cost 30 dollars. But in the quest for stability, nay, in the quest for the very computer bliss we all aspire to, I laid out my coinage for the Antec fancy schmancy model. I thought, "Time to go with a real name, a real psu." .
And here's where the story ends. I swapped out the psu, thinking at this point I was sort grasping at straws, and wham bam thank you ma'am, here I am sitting by my gleaming tiny god, my humming MSI K8T, all is forgiven.
Thanks for the help all. The corsairs all seem to to do their job. Antec apparently does not test their rather expensive "TruePower" psu.
Ironically, the brand of the no namish psu appears to be "Works", emblazoned proudly on it's side.
So if you think ram is ruining your life, stick a piece of crap psu in that rig and see.
There's only one thing left to say.
w00t!

[Athlon64] K8T Neo-FIS2R RAM Question

Similar Messages

Maybe you are looking for