[Athlon64] K8t Neo FIS2R V1

Hi. Trying to set up a K8T Neo FIS2R V1.0 with an AMD Sempron 2800+. When I hit the power button it powers up for 1 second then dies. The green light on the tower flashes and manual says CPU overheat. Checked cpu is seated ok, checked RAM ok. If I unplug the 4 pin power connector the cpu fan then runs ok but nothing else works. Tried different video card, diffrerent RAM, different PSU. I have cleared the bios as stated but problem still exits. Could I have a faulty board? Thanks

You should use at least bios version 2.0, which if i remember correctly is the first one with support for semprons. I recommend 2.1, 2.2 causes some problems with agp aperture size on 256mb.
I don't see any other possibility than getting a "normal" amd 64 processor and then update your bios (of course it would be unnecessary to install the sempron then, because normal 64's generally perform better).

Similar Messages

[Athlon64] K8T Neo-FIS2R RAM Question

Hi All
At the moment I have 512mb of Corsair 3200 RAM (2x 256) in a MSI K8T Neo-FIS2R, and I was wondering if it would be ok to put another 1gig of non Corsair in with out it going nuts at me.
Thanks for any help.

Many thanks for the help.

[Athlon64] MSI K8T Neo FIS2R BIOS Update when? CnQ no workie!

The MSI K8T Neo FIS2R (MS-6702) hasn't had a BIOS update since 3-4-2005!
I put a Sempron 64 3000+ in my motherboard, and was very disappointed that it is recognized as an "AMD Unknown Processor". Sure, it works, but one of the reasons I bought it is in the hopes of getting AMD Cool n Quiet to work. However, apparently the AMD driver can't recognize the CPU due to the old BIOS on the motherboard.
Every other MSI skt 754 board supports Sempron E6 revision already. Why not the K8T Neo FIS2R? Where have all the MSI BIOS programmers gone? I have been waiting 2-months for a BIOS update to support the E6 Semprons. I have asked and begged MSI Tech Support. I am tempted to switch to ASUS or some other company that is actually timely with BIOS updates. Only reason I haven't yet, is this board is everything I want EXCEPT for Cool n Quiet not working. It's starting to look like there is no BIOS update in sight, so I am very disappointed.
Anyone here work for MSI can confirm there are no plans for a BIOS update? Because I don't want to wait around for something that's not going to happen.

Sorry, I didn't mean to imply I thought the mods here are MSI staff... I was just kind of hoping there's MSI staff lurking here, seeing what people think of their products or seeing what people complain about.
No, pretty much C 'n Q is the only reason I'm disappointed, but it was something I was really set on getting to work since this is a server that's up 24/7, but isn't utilized but maybe 4hrs out of a given day. I could reduce frequency and voltage, but unlike C 'n Q, it won't automatically increase speed and voltage based on demand - which is something I want since although it's a server, I also use it as a regular PC as well.
I've even tried the 2.33 beta BIOS with no change, and even found a 5.52 BIOS in their BIOS testing directory. I guess that BIOS was for a different kind of 6702, although I had pulled out the peripheral modules with AMI's MMTOOL and they looked the same as the existing BIOS, but that BIOS killed my motherboard so it couldn't have been for a regular 6702. I had to desolder the BIOS chip with a heat gun, reprogram the old BIOS back on it with an EPROM programmer, and solder in a socket. I guess that shows my dedication to get C 'n Q working!

K8T Neo-FIS2R / Kingston KVR400X64C25/256

As a first time poster my apolgies if this has been covered elsewhere - I have read most of the posts on this forum but found no specific reference. Please just point me in the right direction if i am wrong!
I bought the Kingston KVR400X64C25/256 modules because:
a) they were listed by MSI on the list of tested Ram
b) they were on Kingston's list for the K8T NEO &
c) they were in stock. However...
If installed in DIMM 2 & 3 (as per MSI tested RAM pdf) the system crashes on trying to load Windows. DIMM 1 & 2 'works' if that allows for 8 or 9 restarts/day. I tried 1 & 3 to see if that improved the situation, but if anything it was worse. I have tried increasing the RAM voltage to 2.6 but there is no discernable difference. Upping the TRCD to 4 makes little or no difference.
Memtest86+ initially found no errors (16 hrs/93 passes) but when left running for a week came up with 10 errors (8 in test 6, 2 in test 4). MemTest (http://hcidesign.com/memtest/) gives me an average of 10 errors for 300% pass.
I'm now trying running the memory at 2.7v (within Kingston's ±.25v range).
In the meantime, has anyone run this memory without any problem - i.e. is it a simple case of faulty memory? Equally, has anyone had similar problems and found a solution?
thanks
MSI K8T Neo-FIS2R
AMI rev 1.2
AMD Athlon64 3000+ AMD heatsink/fan (working temp around 32°C)
2 x Kingston KVR400X64C25/256 (DIMM 1, DIMM 2)
NVidia GeForce3 driver v53.03
Antec TruePower 430W +3.3V 28A, +5V 36A, +12V 20A. Max load 410W
IDE1 ST340016A (master) ST320014A (slave)
IDE2 MSI DVD-ROM D16 (MS-8216)
Soundblaster Live 5.1 platinum
Windows XP Pro Version 2002 service Pack 1

Quote
Originally posted by Bas
Hi,
Sorry to say, but as soon as you get errors in memtest, no matter after how many hours, you need to try other memory.
As your memory seems to be unstable....errors in memtest are a NO-NO
hmmm! What if memtest, Prime95 etc. detect no problem over lengthy periods when sticks are individually tested in DIMM1 - as well as the system not crashing once - , but boot failures/memory dumps etc. abound when same sticks are individually placed at 2 or 3? Is this still a memory issue?
For what it's worth I have found Kingston's technical support more than helpful.
MSI K8T Neo-FIS2R
AMI rev 1.2
AMD Athlon64 3000+ AMD heatsink/fan (working temp around 40/42°C)
2 x Kingston KVR400X64C25/256 (DIMM 1, DIMM 2)
NVidia GeForce3 driver v53.03
Antec TruePower 430W +3.3V 28A, +5V 36A, +12V 20A. Max load 410W
IDE1 ST340016A (master) ST320014A (slave)
IDE2 MSI DVD-ROM D16 (MS-8216)
Soundblaster Live 5.1 platinum
Windows XP Pro Version 2002 service Pack 1

K8T Neo-FIS2R/FSR no POST

I have a K8T Neo-FIS2R/FSR (MS-6702) which is, along with all my other components (I'll list them later), over a year old. It has been running just fine until the other day. I have not modified any hardware or BIOS-settings recently.
The day before yesterday my speakers put out a high-pitched shriek and the screen turned black. I then turned off the computer (it seemed to still be running, fans spinning). As I switched it on it let forth 8 beeps followed by a paus, and then 8 beeps again, over and over. I switched the graphics card for another one, no difference.
I then left it turned off for a few minutes. Then I booted it up again, and voila, it worked fine. Then after a few minutes it died the same way, and when I rebooted it it started beeping again.
Switching graphics card doesn't help. I powered it on without a graphics card plugged in. Then it made 8 beeps, and then silence. The cycle was not repeated, as it was when the card was in.
I then used another motherboard, another CPU and other RAM, same graphicscard and harddrive, and it boots into Windows just fine and seems to be quite stable for the day I've tried it.
I then switch back to the K8T-motherboard with it's CPU and RAM (still same graphicscard and harddrive as the other one), and it boots fine. After almost an hour it dies again. On boot, beeps. Wait a few minutes, boots again, then dies. Beeps next time. Etc.
The 8 beeps apparently mean there is a problem with the video card. I have tested two video cards that both work fine on another motherboard, no difference.
Because it dies after a while when it has rested, I suspect some sort of overheating issue. I put a bigass fan blowing at the motherboard and video card but that didn't seem to do anything. The fan on the video card is clean.
I have hooked up the D-Bracket 2 that accompanied the motherboard. It has some lights flashing depending on what is going on, and it halts on "Early Chipset Initialization", which is phase 2 of 16 (1st being "System Power ON"). When I press the power button, the LEDs on my memory sticks flash for a few seconds (showing activity), and the D-Bracket lights up. Then the memory-LEDs go to rest (inactivity), and the D-Bracket halts. Fans keep spinning but there is no life. No beeps.
After leaving the computer off for the night, I cleared the CMOS. The computer booted and ran fine for a couple of hours, then it suddenly made a noise in the speakers, and the monitor went black. Fans still spinning. The little light at the monitor indicating that it is turned on was flashing, as it does when the computer is off and the monitor is on.
This is the hardware in my system at the moment. I have removed plenty of stuff to rule out other components but even with just this it won't work. No mouse, keyboard or other drives attached, just this.
CPU: Athlon64 3200+
Memory: Corsair TWINX1024-3200XLPRO DDR
Power: Thermaltake Purepower Butterfly 480W W0020
Output: +5V (35A), +3.3V (28A), +12V (17A), -5V (0.3A), -12V (0.8A)
Graphics: Gainward GeForce 6800Ultra 256MB GDDR3 AGP8X, "Ultra/2600 Golden S",
Motherboard: K8T Neo-FIS2R/FSR (MS-6702)
Harddrive: Seagate Barracuda IV ATA 7200 RPM
Monitor: Samsung SyncMaster 957p
Any ideas, suggestions or questions? I am stumped.

Quote
I have removed plenty of stuff to rule out other components but even with just this it won't work.
Quote
Graphics: Gainward GeForce 6800Ultra 256MB GDDR3 AGP8X, "Ultra/2600 Golden S",
Quote
+12V (17A),
If your graphics card is like mine (see sig) with two power connections at the back you may have stressed the PSU over the last year to it's final end. Borrow or buy another PSU with at least 24 amp on the 12v supply. Your current PSU with only 17 12v amps was bound to fail. Especially since you state you had other hardware at one time. CPU Graphics card, case fanes and drives are all calling on the 12v rail to power them and your PSU just might not have it any more to do the job and the highest draw is at startup.
Try another PSU.

K8T Neo FIS2R Won't Recognize HDDs

Here’s my situation. I am not new to building computers, but new to the AMD Athlon64, MSI boards, and SATA drives.
I purchased the K8T Neo-FIS2R (601-6702-010) main board. A single 512 MB DDR memory stick is installed. The only card installed is the ATI Radeon 7500 ALL-in-Wonder video card. I cannot get the system to recognize hard drives. I have made many changes in BIOS, but have been unsuccessful.
At first, my intention was simply to take my almost new Maxtor Diamond Max Plus 9 120 GB ATA HDD and install it with the K8T Neo motherboard. The disk has been previously formatted with Windows XP Home, and has various other programs installed. It was working fine in my older system. I put this drive (properly connected to the IDE1 on mainboard), and the K8T Neo would not recognize the drive at all. In fact, all I received were messages that SATA Raid devices were missing (apparently the Promise controller complaining). Trying to deactivate the SATA controller via bios did nothing.
Next, I decided to purchase a Seagate 160 GB Barracuda SATA HDD (ST3160023AS-RK), thinking maybe then the system would at least recognize an SATA HDD. (of course a lot of this shows my naivete’ with newer SATA standards/componets/MBoards) Initially it was recognized, and I was able to use Seagate’s software to partition the drive and format it. However, after rebooting and attempting to install Windows XP, the drive was no longer recognized by the system. On the POST screen, the VIA controller does list it as master device 1 in the SATA.
Okay, here’s what I want: I want to install the Barracuda 160 GB HDD SATA as my boot drive, and take my slightly older Maxtor HDD and make it a secondary (or slave) drive. This means a mix of SATA and ATA drives. Since MSI’s documentation both in manual and the website provides no help (that I can find) on this issue, I need suggestions on what to do. The only explanation in K8T Neo manual is to create an SATA Raid array. I do not want to do this. I simply want the SATA as boot drive, the ATA as secondary (or slave) drive, and for both of them to peacefully coexist! How do I make the mainboard recognize this?

Quote
Originally posted by saat0014
Are you getting the error when you insert the disk and it looks for the drivers on the disk? Or are you getting it at the Windows installation screen. Maybe you should try using the promise drivers and hook up your drives to the promise controller. Here's how to get the Seagate drives to work on the promise controller. Promise Scroll down to where I posted and you'll find hopefully all you need. If you need help, just ask
The error is coming at the Windows installation screen. The drivers already (seemingly) load.
I have tried installing the Promise drivers, although not as you posted in the linked thread. I only have the one SATA drive... do I still need to configure it as RAID?
I'll try this today. In all my years of building computers, I've never had as many problems as I have with this system. This is so frustrating.

Msi k8t neo fis2r odd post issues

well, i went over to a friends house, pulled out his ram..put in in my computer..it posted and boot to windows..perfectly..
so then i go into the bios and up the voltage..so that i can put my old ram back in..it stopped responding when i updated the bios becuase it set the voltage back down to default..so..
i put my ram back in once the voltage is set to 2.75 v and it booted a few times perfectly..i unhooked everything and came home..well
now i try to boot the pc and once again it will not boot? is it possible that the cmos got cleared when i unplugged the pc???
i know my ram isnt bad..i ran it on a friends system while playing games for hours..this motherboard is driving me insane..someone really dropped the ball when they made these..so many issues with having to fool around with voltages etc..cant even get the damn system to post if the voltage isnt up and even then sometimes it seems to not want to ..its crazy..
i know none of my components are NOT broken because ive stresssed them all fully in other peoples computers..
if anyone has any clue as to how i can get this thing to post to get back in the bios plz reply..im at wits end
my system specs are
athlon 64 3000+
512mb mushkin special 2-2-2 ram (i will change the timings to the recommended slightly delayed timings but i have to actually get into the bios to make this possible)
msi k8t neo fis2r bios 1.4

Southmike is sooooooooo right on that one. I see a lot of folks running stuff on other computers with + results and then nothing on the Athlon64 - equipped systems. Well, I think it's O.K. to a certain point, at least to find out if an item is not defunct. But, most of the problems are RAM and PSU related. After that, I believe the BIOS is the biggest issue. And I think some of our forum readers don't actually understand the settings they mess with. I for one, do not fully understand a few of them myself! That is why it's important to make changes in BIOS one at a time.....if you are not as experienced as a lot of folks here at the forum are.

MSI K8T Neo FIS2R- Corsair Twinx XMS4000

Two weeks ago I have bought one MSI K8T Neo FIS2R with an AMD Athlon64 3200+.So far I used the computer with one DIMM of 256MB DDR PC2100 memory. This morning I have installed in the motherboard a pair of CORSAIR TWINX XMS4000 which comprises of two DIMMs of 512MB DDR 500MHz memory.
The computer did never worked again. As soon as I have turned it on, although the whole system got power the screen was blank and the motherboard did not boot. Moreover, the D-Led system of the motherboard has all its leds red which according to the manual means that the processor is probably damaged.I have never overclocked my system and before install the memory it worked perfect. I have disconnected the whole computer but the problem still exists. Can you advise me what I have to do to fix it? What is the cause of the problem? Is there any way so that I can fix it?

Quote
Originally posted by karinio
Two weeks ago I have bought one MSI K8T Neo FIS2R with an AMD Athlon64 3200+.So far I used the computer with one DIMM of 256MB DDR PC2100 memory. This morning I have installed in the motherboard a pair of CORSAIR TWINX XMS4000 which comprises of two DIMMs of 512MB DDR 500MHz memory.
The computer did never worked again. As soon as I have turned it on, although the whole system got power the screen was blank and the motherboard did not boot. Moreover, the D-Led system of the motherboard has all its leds red which according to the manual means that the processor is probably damaged.I have never overclocked my system and before install the memory it worked perfect. I have disconnected the whole computer but the problem still exists. Can you advise me what I have to do to fix it? What is the cause of the problem? Is there any way so that I can fix it?
Hi dude i had identical problem, bought i extra stick 512 400 ddr and the system wont start. Make sure your motheoard support the made of ram. In my case Asus did not support corsaire. Also it could be the slots which are damage.
bye

Booting "issues" with K8T Neo-FIS2R

Well hello everyone. First of all I want to say that my English isn't completely error-free and my problem might seem awkward because of my ways of expression.
I also want to say that i've read alot of threads and searched the forum for my problem.
For a couple of days ago I got all my parts for building my 64bit-system and I build her up. To my suprise it booted, with almost no errors. Although I could install Windows XP and use it completely, everytime I boot it (under the booting sequence) it says "Bios is not installed", although I can enter bios simply (like everyone else) just pushing the DEL-button.
But this isn't the only problem. When I enter PC Health Status it says that the cpu is running at whooping 62-65 degrees. When i have my hand around the cpu-cooler it doesn't even feel warm so I think it has something to do with my BIOS-version that i am running now (Yes, I've read that in much more threads)
Also I have problems using the Cool'n'Quiet technology. I have it supported in the BIOS and activated it although it will not work (maybe it has something to do with the bios?) With this i mean that i will not go underclocked (It's allways 2.2 GHz)
My final problem is that it sometimes takes the system 2 minutes to boot sometimes, it happend after i flashed the bios to 1.7 from 1.0
Under these circumstances I've used 1.0 AND 1.7 BIOS-versions.
I've never overclocked the computer either.
What could be wrong?
I'm using 3200+ 2.2GHz Athlon 64 cpu.
K8T Neo-FIS2R
Radeon 9800pro
Seagate 7200.7 200GB drive.
380W Antec PSU.

Quote
Originally posted by $post[username]
I've tested notebook, minial power savings and battery. C'n'q still doesn't seem to work. Yes i've enabled it in bios. I downloaded the AMD Athlon™ 64 Processor Driver for Windows XP, Version (zip) 1.1.0.14 -
Yesterday my CnQ began to work fine. I've done the same as you:
1- Enable CnQ Bios option
2- Install the AMD athlon64 driver for XP
3- Set "minimal power savings" at windows xp energy options
I have installed the CoreCenter 1.6.8.0 (is the last version) utility, and I've set enable the CnQ in this application. You'll can see that the CPU velocity change "on demmand" and the CPU fan too.
Of course, I've the last VIA 4in1 drivers, 1.7 Bios ver. etc
My temp & MHz values are:
~40ºC ~ 800 MHz idle
~50ºC ~ 2000 MHz playing or that kind of stuff
Note that the PC case is open, because the PC is under my table and there is no good ventilation.

K8T Neo-FIS2R - won't post.

Hello friends,
specs:
K8T Neo-FIS2R
Athlon64 3200 (retail with fan)
two 512mb stick Corsair
1 36 gig SATA Raptor WD hdd
1 80 gig SATA WD hdd
Antec 430 w "TruePower" PSU
ATI 9600 pro
Sony optical drives.
Mitsumi 3.5"
buncha Antec fans.
So I got my new baby all put together and took a deep breath and started it up.
All the fans came on, hdds making hdd type noises, CPU fan a-spinning.
Nothing happens. Doesn't post. No video at all. The MSI usb/diagnostics dongle has all 4 LEDs shining, and supposedly that means the CPU is damged or not seated right.
Poop.
So I take it down, pull of the heatsink and look at the CPU. Looks good. Just to be sure I take it out, look for dust or damage or any abnormalities. Nothing. No physical defects on the CPU pins or the socket. Alright. I carefully put the CPU back, put the heatsink back on (Am I the only one who loves how the heatsink attaches? Bravo AMD!) and.....the same thing happens. I sigh loudly and commence with the near hysterical swearing. Girlfriend announces she HATES it when I build a new PC.
Tried all sorts of other premutations, one stick of ram, unplugging all periphs in different combos, pressing the power button while petting a monkey and eating fire. You name it, I've done it. Does anyone else abuse couch pillows?
You gotta let it out man.
I've probably inserted a few hundred CPUs into ZIF sockets over the years, so I'm 100% certain I didn't muss it up.
So before I RMA these little sweethearts (both the mb and cpu, because how can one tell if it's the socket or cpu?) has anyone else been down this road and want to give me the magic cure? Or maybe just a hug?
Much Thanks to you. Have a good weekend.

Hello Friends,
The Hynix dimms in several arrangements, no go.
I also, uh, borrowed some infineon from work. Tried in several configs, no go.
Samsung no go.
Enter: Despair.
As I sat and stared at the machine in sort of a "I just spent a lot of money and what do I have?" sort of way, mine eyes did fall upon the gleaming brand new Antec "TruePower" psu.
Mind you, I had a perfectly acceptable 450 watt. No problems at all with it. It was generic and cost 30 dollars. But in the quest for stability, nay, in the quest for the very computer bliss we all aspire to, I laid out my coinage for the Antec fancy schmancy model. I thought, "Time to go with a real name, a real psu." .
And here's where the story ends. I swapped out the psu, thinking at this point I was sort grasping at straws, and wham bam thank you ma'am, here I am sitting by my gleaming tiny god, my humming MSI K8T, all is forgiven.
Thanks for the help all. The corsairs all seem to to do their job. Antec apparently does not test their rather expensive "TruePower" psu.
Ironically, the brand of the no namish psu appears to be "Works", emblazoned proudly on it's side.
So if you think ram is ruining your life, stick a piece of crap psu in that rig and see.
There's only one thing left to say.
w00t!

K8T Neo-FIS2R Disable Overclocking Completely!

ok so this is really startin to pee me off
ive got the latest BIOS for my K8T Neo-FIS2R (2.22 i think it is) and it seems to have no way to turn off the Dynamic Overclocking Technology (DOT) crap.
I have disabled cool n quiet, spread specturm and dynamic overclocking yet when my computer loads i have core centre loaded at startup, when i fire off a heavy app (something java'ish usually does the trick) the processor speed whacks itself up to anywhere from 3000-8000mhz and then drops back down to the lovely 2200mhz which it should be running at (its and Athlon64 3400+ chip) problem being i dont want it to do this - i want a stable system and this is causing me major headaches as there are short periods where it seems to almost freeze as the processor is changing from one speed to another
anyone any ideas on how to totally disable DOT before i ditch it and go back to a P4
thanks
ste

Check your BIOS revision with live update or watch the screen on boot up. Are you really using 2.22 or 2.18? If you are, try a BIOS version that isn't beta. Beta versions all end with a digit in the hundredths place, you should go for 2.0 as the jury is still out on 2.1 and 2.2. Get it here I'm currently stable at 1.9. Also, I'm still using Corecenter v1.6.0.0. I found that all of the newer ones (as of 6 months ago) caused a hiccup on speed changes and actually caused a little performance hit. If you want the old version of Corecenter I have, PM me and I'll email it to you if you can't find it elsewhere.

K8T Neo-FIS2R V1.0, CPU Speed Problem

Hi, I got a Athlon64 3500+ (NewCastle) and K8T Neo-FIS2R V1.0 MotherBoard
Just downgrade my bios from 9.2 to 3.3 since the 9.2 bios does not show the correct +3v voltage in the core center and the website is recommending that old version of Athlon should use 3.xx bios.
But the problem occurs, the core center now shows the cpu speed is 1xx rpm and keep sending alarm. I use other software to check the fan speed and it is 2xxx rpm. The temp of the cpu is between 33 to 43 'C.The temp of the case stays at 42 'C. The voltage of the CPU is 1.52-1.53V. One time, somehow the temp of the cpu went up to 50'C but the fan is not turning faster to cool down the CPU. No matter what models (Cool&Quiet or User) I choose in the core center, it just did not go faster. Finally, I have set full speed of the fan in the core center to increase the speed of the fan.
My PSU is Enermax 450W, and I used 5V for my three case fans since they are really noise.
Any problems with my system or computer, or any recommemdation?
Sorry for my English, but I am doing my best.

Everest just has no readings that work for us. They never supported our board. None of the software gets a correct read on our 3.3v so no there is no answer. I have tried them all as have others. If reading the 3.3v is that important to you use a meter.
I have yet to ever trust Core Center. It lies. Keep in mind just how many MSI products it is used in. So far it has yet to be that accurate in any Via Based MSI product. Search the forum here for it. No one seems overjoyed with CC.

Onboard 5.1 sound noisy - K8T Neo FIS2R

Hi guys, i'm new here.
Well, i got a K8T Neo FIS2R and the 5.1 sound is noisy. I've tried many different drivers, replaced my 5.1 speakers for new ones and it doesn't work properly at all. I've been using a 2.1 system and it works just fine. Has anyone seen this problem? any advice?
Thanks in advance
Kein

LOL OK you can save us time by replying to that end the next time. Thanks.
I know it may seem trivial but I can't count how many times a suggestion was assumed to have been tried and it turned out to be the fix in the end. So if we seem grouchy about getting a reply remember that we aren't the only one's that waste time chasing stuff when no one let's us know what they have tested.
OK back to your problem. There are no magic buttons to push. If you have tried other speakers and drivers then it is likely something on the MB that is causing the problem. It could be a power line somewhere close to a chip or connection, it could be a bad ground. If you have a Sound card handy you could also check it to see if the problem goes away. Otherwise you may have to RMA it.

PSU for K8T Neo-FIS2R

What model of PSU has its cooling fans which can be controlled from PWFAN1 and PWFAN2 on the K8T Neo-FIS2R motherboard?
Kaz

Sorry but there is no real specific one out there that I have ever seen. Most of the Bios options you see have been available since forever with Via Chipsetted boards. However DOT is specific to MSI which is Dynamic Overclocking technolodies. DOT can automatically overclock your voard depending one what your doing. I recommend staying away from it as it can cause as many issues as anything in your rig. And then there is Cool and Quiet which is an AMD 64 Bit CPU specific option to downclock the multipliers for the CPU during Idle Times to save energy and keep the CPU cool. Again it is not really needed.
The rest of the stuff you can use google to find individually or by searching for Award Bios's or Via Chipset Bios settings.
These are way to much for any one person to post a complete guide to here as all the info is readily available elsewhere.

Should I flash the bios? K8T NEO FIS2R

Ok... I have a K8T NEO FIS2R mobo. A couple of friends of mine have been telling me to flash the bios to the most current version... Then some other people have been telling me that it is too risky and I should hold off untill something goes wrong that I know a bios flash can fix...
I'm just wondering what is the concencious here... should I flash it, or should I stay with the current version I have now(the one that came with the mobo) I Like to have my computer as up to date as possible, but all the reports of bad flashes have me a little worried. This is a procedure that I have never done before, and I dont want to mess it up.
If I should flash, Any insight, tips, tricks, special instructions, etc... would be greatly appriciated.
Thanks!
Magnum

Thanks guys for the quick responces... I'm used to not getting a responce from forums for 12-24hrs and here it is less than 24hrs later and I have 10 responces.
I'm not at my computer in question right now, but I am almost positive that my bios is ver1.0. Same one that came with my mobo.
At this point I am leaning towards flashing... If basically the only way to mess it up is to have my power fail, then I dont think I will have a problem. I'll just borrow an UPS from work here to be on the safe side.
hypothetically if i follow the instructions to a tee(windows flash/live update) are there any other ways it can mess it up? I just want to get a hold on all the places where I could mess it up.
Will live update take me all the way through the procedure, or do I need a separate set of instructions to read off of during the flash?
Also what gear will I need... floppy disk? anything else?
Sorry about all the questions, just want to make sure I do this right the first time!
Thanks!
Magnum

[Athlon64] K8t Neo FIS2R V1

Similar Messages

Maybe you are looking for