[Athlon64] sytem wont start after i change settings in bios

hi i have had this wierd problem with my system for a while know and the problem is this:
when i change agp apaterur size or change the ddr voltage in bios the system wont start so i have to nullifie the bios to make the system go up again.
the system works just fine otherwise.
it is really anoying and wierd so i would really appreciate if i could get some help with this one.
thx

Some cards won't work with some voltages or apatures no matter what you do. Basically just reset the Bios with the jumper and only do so when the machine is unplugged or you can damage it. Reset the Bios and set to a known working setup on the apature. Leave the voltage be unless you know what you are about as that can fry a vid card or damage other parts if it is set wrong.

Similar Messages

  • HELP !! Computer wont start after i change from 133 to 166 on my FSB

    Hi...
    I have a K7N2G. I changed the my fsb from 133 to 166. Afterward, I have not been able to start or boot my computer (my fans are on, but monitor is not geting any output).
    Thank you and greatly appreciated to anyone that can help me.
    Yoge

    Hahaha yoge i fell yr pain man cos i did the same thing 3 weeks ago!! I just got my computer back from the shop on Tuesday. What happened was i managed to kill some chip on the mother board and the chip had to be replaced.
    This is the story:
    Amd XP 2400+,
    MSI K7n2g-ilsr
    400watt coolermaster
    USING THE ONBOARD VGA!!!! (im a dumb F**K, i noe this now)
    dual channel 2*256mb sticks (transcend & Kingston value)
      I had just installed the latest bios so the kinston is
      supported.
    High performance settings
    FSB/DRAM Ratio 1:1
    The only values i had for the FSB were 100, 133 & 166Mhz so i put to 166, i pressed F10 to save and then black screen.
    The power was on, the monitor was on, but the hard drive shut down shuted down. So i took a look at the back to check the 4 LED's, 1,3,4 were RED and 2 was GREEN which meant the memory module was damaged, or so it said in the manual.
    Apparantly ur not supposed to overclock with the onboard VGA and it even says that in the manual (i must have skipped pass that, duh)
    So yoge your gonna have to take ur computer back to the shop to get it fixed sorry to say.
    I cost me $35 AUD + $55 for service charge but they oly charged me $35 for the sevice fee cos i am a regular customer.
    Also when i got back my computer this week, i opened up the case and do u guys know what i found, a GeForce4 440MX graphic card!!! They gave me a free graphic card!! Woohoo
    Well now my computer runs fine with no problems yet and my cpu runs at 25 degrees where as before it ran at 51 degrees.

  • Dbconsole wont start after password changes

    I have an oracle database on a test windows image that i haven't used for a while. the passwords for lots of accounts had expired, including MGMT_VIEW. I have reset the password on the account to MGMT_VIEW without realising that wasn't the original password for this account and also that you should not touch the password for this account (although what you are supposed to do with it, when Oracle is complaining that the password has expired, is another question). Now however, the dbconsole won't start up at all.
    the release of Oracle is 11.1.0.7
    1) Is there anything that can now be done to "fix" the dbconsole ?
    2) where are the logs for the dbconsole that would explain why it is failing to start ?
    I realise now (now everything has failed!) that MGMT_VIEW is a super important account and you should never touch its password (because it will break lots of things!) but it is done now and i need help to get my database working again.
    sorry for the stupid question but hope someone has some hints.
    thanks

    i solved the issue after another days work.
    i couldn't reconfigure the dbconsole because of the max reuse limit (i was trying to reuse the same password) set in the MONITORING_PROFILE profile. it was causing all sorts of problems when the emca tried to recreate the DBSNMP user object.
    after working through lots of KMs to manually drop the dbconsole / EM repository objects and figuring out this limit above, then i managed to reconfigure dbconsole and get it to run again.
    thanks for your help.

  • Intel imac wont start after changing permission

    intel imac wont start after i changed my hard drive permission to let me read and write, then i clicked apply to all enclosed files.i turned it off no problem. then it never started up again in os x. the grey screen with apple logo appears,then after a minute it restarts, and will keep doing that if i let it. i can start up in windows xp, but i dont know how to do anything in windows xp that will affect os x. i can use the hard drive in target mode, but i cant figure out how that can help me. i use a macbook to view target disk. ive spent hours looking through help and support. finally i do not have the os install disks. PLEASE HELP!

    My apologies for the inept instructions.
    Restart normally. Open Terminal in the Utilities folder. Paste the commands in the Terminal application to avoid typos:
    sudo su
    Press RETURN. Enter your admin password when prompted.  It will not be echoed to the screen. Press RETURN again. Now paste each of the following at the prompt and press RETURN after each.
    chown root:admin /Applications
    chmod 0775 /Applications
    chown root:admin /Library
    chmod 1775 /Library
    chown root:admin /System
    chmod 0775 /System
    chown root:admin /Users
    chmod 0775 /Users
    chmod -R -N /Applications
    chown -R :admin /Applications/*
    Again, my apologies.

  • 770-G45 wont start after ShutDown

    Recently installed MSI 770-G45, problem starts when i regulary shutdown comp. from WinXP or Win7 64-bit.Computer wont start after that, like ther is no power, fans dont spin, no bips, NOTHING. I got to unplug power cord and plugg it again into psu, after that it starts normaly.
    Strange thing is that computer starts normally when i manualy shutdown system(holding the power button on the case).There is no exception, starts perfectly evry time after manual shutdown, no need to unplugg powercord.
    Rest of my components> Phenom II X2 555BE, Kingston 2GB 1333mhz, Sapphire 5770, HDD WD 250gb,PSU Corsair TX 650w.
    Tried to change power cord, tried other PSU, other case (tought its maybe power button but no), changed mobo battery, installed several OS versions (XP, Win7) and still dont have solution.
    MS 7599 ver. 2.0
    Bios version 10.2
    MoBo is new bought it 3 days ago.
    PLEASE HELP!!!!!

    First: It is important to clear CMOS after a BIOS update. Unplug power cable before the clearing, as there can be no power in the system
    Second: Rebuild the system, but outside the case. Use only PSU, motherboard, processor, one stick of memory and graphics card. If it works better then, you may have a short, from a stand-off too many, or poorly isolated wire somewhere.
    But I second it sounds like a motherboard problem. You'd better contact the one who sold it to you.
    Oh, an oldie thing! You will need to install Windows again, with the new motherboard and all.

  • SSMS wont start after Installing SQLServer

    Hello,
     After SSMS wont start after updating VS2012. I have unistallled and installed a number of times but the error message I keep getting indicates that Visual Studio shell Isolated is missing. I have tried to install this directly from the set up dvd but
    no success.
    Also I noticed that VSShell is missing in the C:\Program Files (x86)\Microsoft SQL Server\120\Tools\Binn.
    I am assuming that this has something to do with it.
    Can someone please tell me how to fix this?
    Thank you.
    here is the error message received

    Hi,
    Try the below solution and see how it works.
    Note: Take a backup of the key before make any changes on the registry keys.
    http://support.microsoft.com/kb/322756
    Start regedit.exe
    Go to HKEY_CURRENT_USER\Software\Microsoft\SQL Server Management Studio
    Delete 12.0_Config
    Restart ssms.exe
    Here is the original thread:
    http://social.msdn.microsoft.com/Forums/sqlserver/en-US/aeff13b3-3960-4724-bb9a-7e585651d7f4/sql-server-2012-error
    Thanks.
    Tracy Cai
    TechNet Community Support

  • Safari wont start after i installed avi player any suggestions?

    safari wont start after i installed a avi player any suggestions?

    You may have installed the "VSearch" trojan. Remove it as follows.
    Malware is always changing to get around the defenses against it. These instructions are valid as of now, as far as I know. They won't necessarily be valid in the future. Anyone finding this comment a few days or more after it was posted should look for more recent discussions or start a new one.
    Back up all data before proceeding.
    Step 1
    From the Safari menu bar, select
              Safari ▹ Preferences... ▹ Extensions
    Uninstall any extensions you don't know you need, including any that have the word "Spigot," "Trovi," or "Conduit" in the description. If in doubt, uninstall all extensions. Do the equivalent for the Firefox and Chrome browsers, if you use either of those.
    Reset the home page and default search engine in all the browsers, if it was changed.
    Step 2
    Triple-click anywhere in the line below on this page to select it:
    /Library/LaunchAgents/com.vsearch.agent.plist
    Right-click or control-click the line and select
              Services ▹ Reveal in Finder (or just Reveal)
    from the contextual menu.* A folder should open with an item named "com.vsearch.agent.plist" selected. Drag the selected item to the Trash. You may be prompted for your administrator login password.
    Repeat with each of these lines:
    /Library/LaunchDaemons/com.vsearch.daemon.plist
    /Library/LaunchDaemons/com.vsearch.helper.plist
    Restart the computer and empty the Trash. Then delete the following items in the same way:
    /Library/Application Support/VSearch
    /System/Library/Frameworks/VSearch.framework
    ~/Library/Internet Plug-Ins/ConduitNPAPIPlugin.plugin
    Some of these items may be absent, in which case you'll get a message that the file can't be found. Skip that item and go on to the next one.
    The problem may have started when you downloaded and ran an application called "MPlayerX." That's the name of a legitimate free movie player, but the name is also used fraudulently to distribute VSearch. If there is an item with that name in the Applications folder, delete it, and if you wish, replace it with the genuine article from mplayerx.org.
    This trojan is often found on illegal websites that traffic in pirated content such as movies. If you, or anyone else who uses the computer, visit such sites and follow prompts to install software, you can expect more of the same, and worse, to follow.
    You may be wondering why you didn't get a warning from Gatekeeper about installing software from an unknown developer, as you should have. The reason is that the Internet criminal behind VSearch has a codesigning certificate issued by Apple, which causes Gatekeeper to give the installer a pass. Apple could revoke the certificate, but as of this writing has not done so, even though it's aware of the problem. This failure of oversight has compromised both Gatekeeper and the Developer ID program. You can't rely on Gatekeeper alone to protect you from harmful software.
    *If you don't see the contextual menu item, copy the selected text to the Clipboard by pressing the key combination  command-C. In the Finder, select
              Go ▹ Go to Folder...
    from the menu bar and paste into the box that opens by pressing command-V. You won't see what you pasted because a line break is included. Press return.

  • My System wont start after setting FSB to 200

    My System wont start after I'd set my FSB to 200,
    when the system starts, nothing comes up, and my Pc screen LED just blinks,
    I have tryed to reseting the Bios but it doesn't help, have also tryed with new RAM and new Graphiccard but it doesnt help.
    Please help me:-(
    Am I resetting the Bios wrong? I set the jumper to safe mode and 100mhz, then I use the jumper to clear the CMOS. And the restart at set the jumpers back
    3ghz AMD BARTON
    NVIDIA nforce2 k7bn2 Delta
    512 DDR RAM PCI3200
    300WATT

    Quote
    Originally posted by roobster
    set the multiplier lower , FSB(200) X multiplier (ex.10.5) = 2100 MHz , and your voltage raise it a bit too let say 1,700 ( default is 1.650 ) If this doesn't work at once , keep booting . My rig started up after 5 times . Strange but true .
    does not work if he has a 3000.
    they are multiplier locked.

  • Portege Z930-118 wont start after BIOS update

    my PORTG Z930-118 failover and wont start after i upgrading in middle of upgrade i remove power and press shutdown bottom after that i see the power and wireless but screen still black ?
    Any help please

    Hmmmm.... BIOS upgrade interruption has screwed up BIOS and thats the reason why your notebook doesn't start properly. BIOS is damaged now.
    In such case you need professional help by authorized Toshiba service provider.
    On this forum you can find many threads about similar problems. Some people have tried to fix this alone and if you are interested to read how one other forum user has fixed it check please this thread.
    Ayway, you can contact nearest Toshiba service, explain the situation and ask for help.

  • Satellite C850-19D wont start after UEFI to CSM change

    After wrongly change BIOS between UEFI to CMS, saving changes and leave, after reeboot the screen runs mad and dont let me access either BIOS or Windows.
    Sugestions?
    Thanks by the way

    I’m afraid there must be some BIOS or EPROM / motherboard issue.
    It looks like the POST (power on self test) cannot be passed properly.
    Not quite sure if the issue can be solved easily and from my point of few you would need to contact the authorized service provider for help…
    Therefore I recommend you to contact the ASP guys and to ask for assistance…

  • Iphone 5 wont start after standby

    My iphone 5 screen went with blck/wite vertical stripes. After one month going to flat battery and charging it restarted. Now every time goes to standby it wont start. Only by rebooting. Does anyone know how to fix it? Is it a iOS 7.0.6 sw problem? YOur help is very much appreciated as my phone is out of warranty for a month :-(

    Hello Duartesilva,
    It sounds like you are unable to turn the phone back on normally and must reset it to get back to your home screen. I recommend starting creating a backup of your device to iTunes with this article:
    iOS: How to back up and restore your content
    http://support.apple.com/kb/HT1766
    And restore it from your backup with this article:
    Use iTunes to restore your iOS device to factory settings
    http://support.apple.com/kb/ht1414
    If it is a software issue, these steps will resolve it.
    Thank you for using Apple Support Communities.
    Cheers,
    Sterling

  • ATV G2 wont start after restore

    Trying to restore ATV G2 using USB and iTUNES 11.0.4  After restore (which seems like it goes OK), ATV wont start up.  I get a slow blinking light, the apple screen, and then nothing.  Eventually light starts blinking fast.
    Is this a hardware issue?
    Have I restored the wong version of software/firmware to my ATV?

    Well, since I had a video signal, I assumed that the HDMI wasn't a problem.
    Network (WIFI- using a new Time Capsule Airport) worked with all other Apple devices in the house.
    Here's what I did to solve:
    Unplugged ATV2
    Waited 3 days (no particular reason- just no time to mess with it)
    Performed a restore again (power was not plugged in to ATV during restore)
    Reconnected.
    Now it works fine.
    Can't explain why.
    (I don't think anything changed over those 3 days)
    I guess if at first you don't restore, try, try again.
    Thanks

  • Safari wont start after Leopard software update

    After updating Leopard to 10.5.7, Safari wont start. I get an error message "Cant load Tastyapps AV plugin." or something to that effect.
    What gives? anyone know?

    I was using Videobox as a trial version (on the site you have the option of buying or trying for 30 days). After the 30 days it stopped working and I just moved it to the trash. I seems to have left something in Safari however that causes it to not want to start.
    Using Firefox i was able to go back to the Videobox site and download and install the trial version again. I was then given the option of installing the Safari plug in which i did. I then went to the Videobox menu and clicked on uninstall Safari plugin. and then i just moved videobox to the trash again using AppCleaner.
    So, you should be able to do the same thing. Just click on "download" instead of "buy" on the Videobox site. I'm sorry, I couldnt find the plugin files for manual deletion either.
    Maybe you should start a new thread and someone will know how to do that.
    Thanks!

  • Thinkcentre M57 dead after changing settings in BIOS

    Hello,
    I have am M57 tower that has been running great for many years but now all of a sudden after changing a few settings in BIOS (I did not upgrade the bios) all I can get the machine to do is power cycle over and over again with fans at full speed. I attempted the steps here http://forums.lenovo.com/t5/A-M-and-Edge-Series-ThinkCentre/M57-BIOS-Update-Failure/td-p/55840 but no luck. I did not change any hardware recently. I have also removed the descrete video card in it but there is no difference. When I attempt to recover the BIOS via a usb desette drive it beeps once then reads the disk for about 5 to 10 seconds with the fans at full speed. Any help would be appreshiated. I never knew you could brick a system by changing settings.

    Odd that you followed procedure and that still didn't do it. Change the coin battery on the motherboard, restart pressing F1. Once into the BIOs with a new battery installed, go to the last page and select Load Default Settings, and then select F10 to Save Changes and exit. If all this was caused by a weak battery, this should fix it.
    You can find coin batteries (CR2032) at Home Depot or even Walmart.

  • Touchsmart tm2 notebook wont start after standby

    I have a touchsmart tm2 that shot down after I started using it from stand by and now the notebook wont start, only the battery light is showing but it won´t do anything else

    Hi
    You have a couple of options as I see it please try these steps might help you to fix your issue.
    Resolving Problems with Sleep and Hibernate Mode
    Let us know how it goes!
    *Although I am an HP employee, I am speaking for myself and not for HP.
    ****Click the White Kudos star to say thanks****
    ****Please mark Accept As Solution if it solves your problem****
    Regards
    Manjunath
    Let us know how it goes!
    "I work for HP."
    ****Click the (purple thumbs up icon in the lower right corner of a post) to say thanks****
    ****Please mark Accept As Solution if it solves your problem****
    Regards
    Manjunath

Maybe you are looking for