Ati catalyst 4.4 and up won't install

I can't install any Ati catalyst driver versions above 4.4, I have a Gecube Radeon 9800XTreme and a Gecube 9200Se and drivers up to and including catalyst 4.3 install fine with either card but any version above gives message "Setup was unable to find components that can be installed on your current hardware or software configuration. Please make sure you have the required hardware or software." Same goes for any of the modded drivers in those versions. All works fine in my other Asus Amd based computer. Any one else had these issues and maybe a solution.

If you are trying to install Control Panel you need to have Microsoft .net framework installed first.

Similar Messages

Does final cut 5 work on 10.7 lion as it was but i bought a new macbook air and it won't install now ?

does final cut 5 work on 10.7 lion as it was but i bought a new macbook air and it won't install now ?
i had it work on my second gen mba but now it wont work

Hi David
I meant to say 5.1 the problem I've got is it's saying it does support ppc software but I have got the intel version but for some reason won't install from disc but if I transfer from time-machine backup it works
But then it won't read my project it's so strange just don't get it

Help me I bought PSE 13 and it won't install on my new HP ENVY notebook.

Help me I bought PSE 13 and it won't install on my new HP ENVY notebook. Error 7.

cs5,cs5.5: https://helpx.adobe.com/creative-suite/kb/errors-exit-code-6-exit.html
lightroom: http://helpx.adobe.com/lightroom/kb/exit-code-7-displays-installing.html
photoshop elements 13: Installation errors | Exit Code: 6 and 7 suberrors
premiere elements: http://helpx.adobe.com/premiere-elements/kb/updated-installation-instructions-premiere-ele ments.html

I bought snow leopard and it won't install

I bought Snow Leopard and it won't install. It keeps saying, "You can't use this version of the application Install with this version of Mac OS X. You have Install Mac OS X 23.1.1."

Hi stedman, in theory, since the machine is a 2008, going from Lion to Snow Leopard should be possible, but requires the usual startup proceedure, boot holding the C key, then since ML is on the hard drive you must do an erase and install. You cannot do a reinstall. I say in theory because if all firmware updates have also been done following installation of Lion, there may be a firmware block now causing problems reading the SL disk.
That is the problem we all face trying to help diagnose these situations remotely...incomplete information.
So, for bistraung: how exactly are you trying to install SL? Are you trying to restart your computer with the SL disk in the optical drive and holding the C key? Or, are you trying to read the disk directly? You cannot do the latter.
Do you have a backup of the drive? If you do the SL install, you must erase the hard drive before installing SL which means you lose everything on the hard drive. So me sure you have a backup or you cannot get anything back.
Best approach would be get an external hard drive, format it Mac OS Extended (Journaled), GUID partition table, and then use Carbon Copy Cloner to make a bootable clone of the internal hard drive. I say CCC instead of SupperDuper since CCC does a better job of also cloning the Recovery Hard Drive, which will be important if you need to work on Lion at all.
With a bootable clone, you can boot to either SL on the internal drive or Lion on the external drive...gives you options.

Restored iPod, and it won't install the 5.0 update. What can i do?

I restored my ipod for the most recent update from 4.0 to 5.0 and it won't install the software, it just keeps freezing at exactly the same point each and every time.

At what stage does it freeze? What is showing in the status bar?
This may be applicable:
Hang during restore process: Following Troubleshooting security software will frequently resolve this error. This error can be caused by the default packet size being set incorrectly. There may be third-party software installed that modifies the default packet size in Windows by inserting a TcpWindowSize or MaxGlobalTcpWindowSize entry into the Registry. Contact the manufacturer of the software that installed the packet-size modification for assistance in adjusting this TcpWindowSize values. Typically the default packet size is modified by 3G cellular network card software, ISP communication software, or Internet speed download optimization software. There are legitimate reasons to change the TCP/IP packet size and not use the Windows default settings (for example, network traffic optimization, home/broadband optimization, enterprise app optimization such as database apps, Exchange, and more). Deleting the "TcpWindowSize" or "GlobalMaxTcpWindowSize" entries in Windows Registry could affect the system's performance with other apps or on their network connections. Deleting the customized TCP/IP settings may require the reinstallation of any third-party applications that had modified the TCP/IP settings from the Windows default settings.
There are two ways to resolve this:
You can follow this article by Microsoft: How to reset Internet Protocol (TCP/IP) , or follow the steps below to manually find and remove TcpWindowSize and MaxGlobalTcpWindowSize entries from the Registry.
For Windows XP, Windows Vista, Windows 7: Go to the C:\\Windows folder and launch regedit.
Go to Edit > Find.
Search for "TcpWindowSize" entries. There are typically multiple entries of TcpWindowSize/GlobalMaxTcpWindowSize spread throughout the entire Registry. If "TcpWindowSize" exists, one or more third-party applications have changed the user's default Windows settings for TCP/IP.
Go to File and select Export. This step will export a copy of the Registry that can be used as a backup of the original settings.
Delete the "TcpWindowSize" entry.
Search for the next "TcpWindowSize" entry and delete each one until the Registry no longer has any "TcpWindowSize" entries.
Close Regedit, restart the PC, and test.
If you are uncertain as to why these registry entries exist and the PC is a business computer, contact your network administrator and determine what values TCP/IP can be set in their Windows Registry setting so that the PC can update or restore an iOS device rather than deleting the "TcpWindowSize" entry.
If editing the registry does not resolve the issue, restoring on a different computer that did not install the communication software is the step most likely to resolve this issue.
From:
http://support.apple.com/kb/TS3694

Updated ipod touch to software version 51.1 and now won't install certain apps

updated ipod touch 4th gen with software version 5.1.1 and now won't install purchased apps family guy time warp and uncensored. Help please as now i can't use my purchased games.

What happens if you just restore to factory defaults/new iPod (not from backup)?
If you still have the problem that indicates a hardware problem an an appointment at the Genius Bar of an Apple store is in order.

I bought lightroom 6 upgrade and it won't install

I bought lightroom 6 upgrade and it won't install.
I download the file and run set up, I log into adobe and then it says it does not find a product
Ihave lightroom 5.71 installed at present.
I spent 24 hours waiting to install and then when I download it won't install!!!!
I am not happy.

I get this error if I try to download from link in my account. Using Chrome on Windows 7
413
Header Length too Large
https://store1.adobe.com/cfusion/store/html/index.cfm?event=displayDownloads&orderNumber=A D002894780UK

ATI Catalyst 9.2 and "Incompatible display adapter has been disabled."

Hi,
I have this issue... on 3 GPUs. Only one is working. 2 x 3870x2 in crossfire / Vista x64 SP1
I tried everything possible : uninstall all ATI software before, clean registry, delete files, temporary files, many uninstall and reboots, trying different settings in BIOS . Same issue.
This time I choose to install 9.2 drivers only (without Control Center), but the result is the same.
The problem appears since v8.11, but I was able to install at the end by cleaning / reinstalling many times.
v8.12, v9.1, v9.2 are impossible to install correctly on my system. I'm very disapointed.
I've been waiting about 6 month for 8.10 to have stable drivers...
Maybe installing ATI drivers should be proposed to Olympic Games category...
I asked to ATI if they have a tool to clean all previous drivers, and they suggested this link :
https://support.ati.com/ics/support/default.asp?deptID=894&task=knowledge&questionID=1447
Look at the utility cat-uninstaller.exe date : 10/08/2003 !!!
It's possible that the problem comes from old drivers, but I refuse to format / reinstall the system each time ATI release a new driver. I did that for 8.12 and I had the same issue.
For users who have this problem : OPEN A TICKET TO ATI CUSTOMER CARE !!!
http://support.ati.com/ics/support/default.asp?deptID=894&task=knowledge&questionID=31625
That's the olny way to solve this issue.
My system below :
AMD Phenom 9950 BE / Sunbeam Core-Contact Freezer / ASUS M3A32-MVP DELUXE-WIFI-AP (AMD 790FX/SB600 - BIOS v1406) / OCZ Reaper HPC Edition 8Go ( 4*2Go ) PC8500 1066MHz Cas 5-5-5-18 / Quad CrossfireX : dual MSI R3870X2-T2D1G-OC - ATI Catalyst 8.11 / RAID0 : 2x Samsung - Spinpoint F1 - 320 Go 7200 rpm SATA II 16 Mo cache / PSU : Thermaltake - TOUGHPOWER 1200W / VISTA x64 SP1

I did tests on my second system :
System 2 :
AMD Athlon X2 6400+ / ASUS M3A79-T Deluxe (AMD 790FX/SB750) / 8GB DDR2 800MHz Corsair Doninator / RAID0 2x Samsung 200 Go SATA II
CrossfireX : 2x MSI RX3870-T2D512E-OC (v120 + v803) / ATI Catalyst 9.1 / Cooler Master Real Power M620 (620W/efficiency >80%) / VISTA x64 SP1
On this system :
Catalyst 9.1 working and Crysis Warhead too
Catalyst 9.2 installation is OK, but :
- Crysis Warhead hang at 85% when a level is loaded
- Crysis v1.2.1 load correctly, but hang after 1 minute
- I noticed that when I lanch CPU-Z 0.3.2 I have on "Bus Interface"
-card 1 : PCI-E x16 2.0@ x16 2.0
-card 2 : PCI-E x16 2.0@ x16 (in catalyst 8.10, both are @2.0)
Uninstall 9.2 and visual c++ x64, reboot, install 9.1 => 2 x GPU disabled error 43 !!!
Going back to 8.10 : it's the last working stable revision from MSI.
For users who use MSI Live update, and drivers from MSI : what are the last ATI Catalyst revision drivers furbished by MSI ?
I would like to have feedback (vista x64, crossfirex).
Thanks

Leopard completely trashed my HDD and now won't install on my MBP

I only moved away from Windows in the summer and now I feel I'm no better off. I've just upgraded my new MBP (only a few months old) to Leopard and it failed. Not only did it fail with some Sibling Link error (which fsck_hfs -r and other internet search result recommendations failed to resolve) but it resulted in my having to completely reformat my drive!
I then let the install disk do a format of my drive and install and now I get this "The installer was unable to create the folder BaseSystem.pkg on the volume ...." or words to that effect. So now I have a new MBP that won't boot and won't install an operating system!
What is this? Apple's Vista?
Is there anything I can do to get this operating system to install???

do you have a software install disk that came w/ your computer. If so, load it up, go to disk utility, zero out your HD, and then reinstall the OS from that disk. Leopard absolutely, completely, totally, and irreversibly hosed my pbg4, so much so that not only would it not eject the fri@@@@ Leopard DVD, it wouldn't even cotton pickin' START UP, save for booting into Open Firmware.. I decided that before I trashed it, I'd try one more time to start it up, hold down the **** eject key, to see what happened. I waited 30 minutes to let myself cool off before using the **** thing as target practice and, well, what'd'ya know, it started up, ejected the Leo DVD, immediately following which I inserted the disc for 10.2.7, shut it down, started it up, it booted immediatley into the installer for that OS, I went to disk utility, zero'd out the HD, after which I went about installing 10.2.7. I'm now on my pbg4 w/ that system installed and it's working (so far) flawlessly. What an absolute crock of rat @@@@ Leopard is turning out to be. Oh, btw, on this pbg4 there were no haxies, no 10.4.10 widgets, nothing fancy, save perhaps for Nisus Express and Firefox. I have Leo on a separate HD on my g5 dual 1.8 which is exactly where it's going to stay until all those bright bulbs at Apple can figure out what the **** is going on.
Hope you have better fortune,
tony

Purchased XFI extreme audio PCIe for someone and it won't install on vista 32

The hardware isn't detected and thus cannot be installed. I had the same problem with my fatality titanium but at least there was a patch download for windows 7 so the card can be detected. No such patch exists for the extreme audio PCIe which means the card won't install under windows vista or windows 7.
Am I missing something or what? I have read other similar complaints about this particular XFI.

EUREKA!
Reading the bowls of the post just below, It said to make sure shockwave was enabled. It wasn't!! I enabaled it and tried my web sites and things worked fine.
Thanks to those that post helpful answers

IMac Clean install and now won't install Lion 10.7.5

My mid 2007 iMac was haveing trouble connecting to the internet via a browser and I took it into the Genius Bar and their only suggestion was to do a clean install and then see what happens. I wiped the computer and tried a clean install. It wouldn't install OS X 10.7 Lion (which this computer was previously running). I took it back into the Genius Bar and they had to install 10.6 Snow Leopard. And now it won't upgrade to Lion (that it used to run till it started having problems).
What's going on?
Now, 3 weeks later, on our other mid 2007 iMac is starting to have the same issues.
Is there something wrong with the OS? I go to network diagnostics and it says it is connecting to the internet just fine. But it won't connect via a browser or do software updates.
I go to Airport Utilities and it wants me to forget the AirPort Extreme. Exact thing happened on the other iMac and I couldn't ever recover (or discover) the Extreme.
Help !!!!!!!!

You mean 2011 or do you mean Mountain Lion? Lion came out in mid 2011 and ML in 2012. And yes, 7,1 is the model identifier. Here is something I found on running the current OS:
From this site:
http://www.everymac.com/systems/apple/imac/specs/imac-core-2-duo-2.0-20-inch-alu minum-specs.html
Did you try recovery?
Not sure if your machine would be able to qualify for the recovery disk assistant (since yours would need the assistant to create a recovery partition)
http://support.apple.com/kb/DL1433
If that works, you should try using the recovery option (hit Command + Option + R during restart) to connect to Apple's servers and reinstall Lion.

ITunes and Quicktime won't install on my computer

Hello,
I just downgraded to Window Vista SP2 from Windows 8.1 and now i cant install iTunes or QuickTime. Everything i tried wont work, i tried installing it both, serpate, older verisons of iTunes, following the support context on Apple, cleaning my computer.
Heres what the error stats:
QuickTime: Verify that the file exists and you can access it
iTunes: Errors occurred during installation your system has not been modified
I don't know what to do.

Hi there Aideed,
I would recommend taking a look at the troubleshooting steps found in the article below.
Issues installing iTunes or QuickTime for Windows
http://support.apple.com/kb/ht1926
-Griff W.

Just bought PSE 12 and it won't install help?

Just bought PSE 12 and it will not install on my Windows 7 computer. I keep getting errors. Been on hold for 36 minutes with Adobe chat and still waiting to talk to someone. Any help would be greatly appreciated!

You need to state exactly what error messages you are getting and if possible post screenshots of these errors.
G/L

[SOLVED] AMD/ATI Catalyst 11.4 and version issue

i installed catalyst 11.4 from aur pkgbuild...
also before i had catalyst 11.2 !
now when i check catalyst version from ATI control center i see 11.2
but with pacman -Qi catalyst command i have catalyst 11.4-1 !
which one is correct ? how can i have 11.4 version number in ATI control center ?
Last edited by roozbehonline (2011-04-29 08:55:26)

thanks dude
it fixed

Access Connections and Tools won't install properly

I have followed advice uninstalled the wireless driver, access connections, hotkey, power manager. . Reinstalled all ( latest versions) except access connection. Wireless connections work correctly and all hot keys function appropriately ( including Fn +F5 ). Then I let TVSU download Access connections. An icon is placed in the task tray. Clicking on it nothing happens. Also none of the hot keys work including the blue ThinkVantage key. Once I uninstall Access connection I am back in business with the wireless connection and the hot keys working. ( for all these installs I turned off the Microsoft virus scanner and the firewall).
Have similar problem with ThinkVantage tools in that I get the Icon in the task tray and then the program freezes. No problem in reinstalling PC doctor5
T60 series2007 Windows XP professional pack3.

Hi dulverton,
I find lenovo drivers and software rather eccentric; since they need to be installed in a particular order to work properly.
First uninstall your wireless driver and access connections, thereafter reboot your system. Then install wireless driver first, again reboot, subsequently install access connections, reboot again.
Further this is the order in which the following drivers must be installed for each of them to function desirably:-
1) Lenovo PM driver
2) Lenovo System Interface Driver
3) Hotkey driver
4) Wireless driver software [reboot]
5) Access Connections [reboot]
Hope it helps.
Maliha (I don't work for lenovo)
ThinkPads:- T400[Win 7], T60[Win 7], IBM 240[Win XP]
IdeaPad: U350
Apple:- Macbook Air [Snow Leopard]
Did someone help you today? Compliment them with a Kudos!
Was your question answered today? Mark it as an Accepted Solution!
Lenovo Deutsche Community Lenovo Comunidad en Español
Visit my YouTube Channel

Ati catalyst 4.4 and up won't install

Similar Messages

Maybe you are looking for