ATI Cedar PRO [Radeon HD 5450/6350] GPU acceleration disabled

Question

Hi,
my graphics card is a
01:00.0 VGA compatible controller: Advanced Micro Devices [AMD] nee ATI Cedar PRO [Radeon HD 5450/6350]
i've installed xf86-video-ati, ati-dri, mesa and linux-firmware.
if i have a radeon entry in my mkinitcpio.conf or a entry in my /etc/modules-load.d/modules.conf, i get acceleration not enabled:
[ 15.348683] radeon 0000:01:00.0: disabling GPU acceleration
any ideas anyone?
thanks for your help
mongohorst

Answer 1

cat /etc/mkinitcpio.conf
# vim:set ft=sh
# MODULES
# The following modules are loaded before any boot hooks are
# run. Advanced users may wish to specify all system modules
# in this array. For instance:
# MODULES="piix ide_disk reiserfs"
MODULES=""
# BINARIES
# This setting includes any additional binaries a given user may
# wish into the CPIO image. This is run last, so it may be used to
# override the actual binaries included by a given hook
# BINARIES are dependency parsed, so you may safely ignore libraries
BINARIES=""
# FILES
# This setting is similar to BINARIES above, however, files are added
# as-is and are not parsed in any way. This is useful for config files.
# Some users may wish to include modprobe.conf for custom module options
# like so:
# FILES="/etc/modprobe.d/modprobe.conf"
FILES=""
# HOOKS
# This is the most important setting in this file. The HOOKS control the
# modules and scripts added to the image, and what happens at boot time.
# Order is important, and it is recommended that you do not change the
# order in which HOOKS are added. Run 'mkinitcpio -H <hook name>' for
# help on a given hook.
# 'base' is _required_ unless you know precisely what you are doing.
# 'udev' is _required_ in order to automatically load modules
# 'filesystems' is _required_ unless you specify your fs modules in MODULES
# Examples:
## This setup specifies all modules in the MODULES setting above.
## No raid, lvm2, or encrypted root is needed.
# HOOKS="base"
## This setup will autodetect all modules for your system and should
## work as a sane default
# HOOKS="base udev autodetect pata scsi sata filesystems"
## This is identical to the above, except the old ide subsystem is
## used for IDE devices instead of the new pata subsystem.
# HOOKS="base udev autodetect ide scsi sata filesystems"
## This setup will generate a 'full' image which supports most systems.
## No autodetection is done.
# HOOKS="base udev pata scsi sata usb filesystems"
## This setup assembles a pata mdadm array with an encrypted root FS.
## Note: See 'mkinitcpio -H mdadm' for more information on raid devices.
# HOOKS="base udev pata mdadm encrypt filesystems"
## This setup loads an lvm2 volume group on a usb device.
# HOOKS="base udev usb lvm2 filesystems"
## NOTE: If you have /usr on a separate partition, you MUST include the
# usr, fsck and shutdown hooks.
HOOKS="base udev autodetect pata scsi sata encrypt filesystems usbinput fsck"
# COMPRESSION
# Use this to compress the initramfs image. By default, gzip compression
# is used. Use 'cat' to create an uncompressed image.
#COMPRESSION="gzip"
#COMPRESSION="bzip2"
#COMPRESSION="lzma"
#COMPRESSION="xz"
#COMPRESSION="lzop"
# COMPRESSION_OPTIONS
# Additional options for the compressor
#COMPRESSION_OPTIONS=""
cat /etc/modules-load.d/modules.conf
radeon