ATi Radeon HD2600 firmware update

I keep getting this as an update - I download, install and get the "installed successfully" message. Anyone else keep seeing this happen?

Check to make sure you have the iMac update 1.21(10.4) or 10.4.11 or iMac update 1.3(10.5) or 10.5.1 inatalled prior to running the graphics update.
http://www.apple.com/downloads/macosx/apple/firmware_hardware/imacgraphicsfirmwa reupdate10.html

Similar Messages

How to How to install ATI Radeon HD2600 driver on bootcamp 3.0 windows 7 partition w/black screen problem

Ok....so i've posted this question in a different way, and i gotten several "scratch the surface" answers from people just saying to install "Ati catalyst", or insert the os x dvd and run set up.exe, and update to boot camp 3.1 or 3.2...while these all seem like great suggestions, I am finding myself needing more specific direction or "hand holding" so to speak.....here is the MAIN problem...
The Background/history
I used boot camp (3.0, and i found updates for 3.1 for imac and for windows, but can't find for mac pro, AND they all are ".exe" files which run on windows..which as you'll see is the big part of my problem...So I recently updated my mac pro (with the ATI Radeon HD2600 graphic PCIe card with 10.6.7 from 10.5.8. I created a single partitioned drive to install windows 7 professional 64 bit. The download software function didn't work (Thanks, APPLE for that poor level of support) so have to select the option that i have already downloaded, or have other media with the drivers already on it....i restarted with the windows 7 disk in....
The installation of Windows 7 Pro 64-bit
So the installation of windows 7 seemed to go flawlessly, was able to use my existing 23" hd apple cinema display (so somehow it has drivers that work with the graphics card, or maybe the motherboard's on board video components) and i select english, and install now, custom, blah, blah, blah...installation causes a few reboots, then restarts ultimately back in os x since that is the default boot os i use on this desk top and have to do the "opt" button to select booting in windows....so when i try restarting in windows, now using the actual boot drive on which i am installing it, it ran through another reboot or two, but then after that, my display goes black.... in the communities, the solution sounds super simple... "go download the ATI catalyst for the black screen problem....windows 7 doesn't have device drivers that work with the ATI radeon hd2600...no problem, just go download and install...."
The problem, re-emphasized : I cannot even finish the install for windows, because of this driver problem....i cannot see anything....I have tried to reboot in safe mode, and that then seems to invoke whatever basic drivers that do work, likely through the motherboards onboard video vs the actual graphic card, and the screen works and says that it's wanting to complete the installation, so i'm thinking awesome this is gonna work....and then.. "windows installation was not completed and cannot be completed in SAFE MODE, need to restart, blah, blah, blah" pops up...and forces reboot...so Safe Mode allows me to see, but won't allow me to finish the install of windows 7...and without completing the install i can't run (ranther I DONT KNOW HOW TO) any of the various .exe files everyone is telling me are the solutions to my problem...like update 3.1 and 3.2 bootcamp...they're all .exe files? not sure why, because bootcamp runs in 10.6.7 i thought, but whatever...it needs running Windows to execute...then the ATI radeon hd2600 driver for windows 7 that i downloaded from the site has an installation program that is an .exe file, which needs windows to run... Does this make sense, why i can't just use these fixes, that seem to be the only fixes out there....so can someone school me step by step here (not just the highlights) of how to update bootcamp, and how to install the ati radeon driver without having been able to complete the windows 7 installation because the monitor goes and stays black????
This is so very frustrating for the record...and any substantial help "not just go download this..." would be immensely appreciated.
Some other things i've been told to try that i've tried and nothing seems to happen as i'm told it will....
---I've been told to install the osx dvd and run "setup.exe" - AGAIN...it's an exe file...and 2 - when i put in the os x file it just wants to re install 10.6...so need more help if this is even a real solution to understand how to make it work...
---I've been told to update boot camp to 3.1 and/or 3.2 from 3.0, using Apple Software Update....Well, my software update is saying everything is up to date and there is nothing new to download at all, and when i reverify the bootcamp version it is still only 3.0.2...and again downloading the updates from www.apple.com/support/ for 3.1 and 3.2...all of those are .exe files...need windows to run them...again, refer to the problem described in detail above...
---I've been referred to the black screen on imac early 2011 thread saying it should fix my problem...and reading it it SEEMED like the most promising resolution...it involves creating a boot flash drive for windows 7 and an xml file that sets the imac drivers to auto install during the windows installation..and it got me farther than anything else..but still ultimately ended up in the darned black screen...my assumption is that it's because it's for imac and not mac pro so not ati-radeon specific drivers....ok....that's enough..please...anyone who thinks they can help...your help is desperately needed...thanks so much in advance!

hey Hatter, thanks so much for getting back...so just to be super clear...is there no way to install the drivers using an exe file given my current state? no way to do it with command prompt or something? if can make work with existing card, i'd prefer it...now when you say it's 'toast' how do you mean? it works well with the os x partitions and always has...so i'm not sure i follow, just want to be clear...
Now to your point of starting with only the one drive installed...so i would put that bootcamp drive in bay 1 and disconnect the rest...i'm not totally sure what you're suggesting the effect should be of doing this? just that i'm just installing windows without the bootcamp deal...but if windows 7 doesn't support the ati radeon hd2600, it still will go black screen no? or you're saying it will run video through the motherboard if it's the only bootdrive, and will run all the way through the windows install without trying to switch over to the hd2600? (slrry flr these questions..just really want to make sure i understand what you're telling me..thanks so much for your patience and help by the way...it's very greatly appreciated...your support is priceless!
So now, assuming none of the above is possible...referring now to the ati 5770 that you referred to...you mention it works with 10.6 well, and that windows 7 supports it ...2 questions on that
1) Windows 7 supports" meaning, out of the box windows 7 supports it? or will i have to install drivers still through some update, because again, if that's how i have to do it, then won't work, cuz can't start windows to see anything to install any drivers or run any thing at all...so it would have to just work with initial installation.
2)hardware wise for my Mac Pro 3,1...intel dual quad core xeon, blah blah....will this card work? it's a PCIe and should fit on my board no prob, etc?

Mac Pro with ATI Radeon HD2600, can't get Vista Aero to work

Hi from Newbie
I have a Mac Pro with Vista bootcamp installed, ATI Radeon HD2600, 512 mb of video ram, and 8 gb's of RAM, but I can't get Vista Aero mode to work. The driver doesn't specify WDDM, could this be the problem? Can I find a compatible driver elsewhere?
Thanks in advance.

You need to install drivers from ATI directly.
http://ati.amd.com/support/driver.html
And when upgrading drivers, it helps to use Driver Sweeper and follow some recommended steps:
http://evga.com/forums/tm.asp?m=396474
(applies to any driver but written with Nvidia in mind)
Of course to get full benefit of RAM, and power of your system, you need 64-bit version.

Satellite P10-824: ATI Radeon 9700 driver update to newer version

I have the ATI mobility radeon 9700 display drivers version 6.14.10.6422 dated from 10.02.2004 running.
I'd like to update the display drivers to a newer version, but I don't find any newer versions.
At the ATI homepage I can download the Catalyst 7.9 drivers, but during install it says they are not compatible with my graphics adapter.
At the Toshiba homepage only even older drivers are available.
Can anyone help me?
thanks in advance
Torben

Hi
Take a look onto the *www.omegadrivers .net* site.
The ATI drivers from this site are a little bit modified and should run on the notebooks.
I use the GPU driver from this site and it works fine!!!
Check this!!!

ATI Radeon HD2600 with FCP HD

Hi,
Will this card enable me to edit HD video with FCP?
It's part a system I'm thinking about buying from someone, my first mac.
It's a 24" model. How easy is it to upgrade the video card, if that's needed?
Thanks,
Tim

It's a 24" model.
I take it you are talking about an iMac? You can't upgrade the video card on that model.
Most of FCP will run on it as it is, though Color will probably be dog slow.
Consider also that the iMac is limited to using USB and FireWire connections so you will be limited to working with DV, HDV and AVCHD video formats. There's no way to add a capture card.
You can find the system requirements for Final Cut Studio [here|http://www.apple.com/finalcutstudio/specs>

ATI Radeon HD 2600 firmware update and others

Hi all,
About a month ago my 1 month old 2.4 imac was replaced with the 2.66 on account of noise after the firmware update. I do have quite a few software updates now and I am a bit concerned about updating them. I am also very new to using a MAC.
1. ATI Radeon HD2600 which updates the firmware ( I have absolutely no problems with graphics)
should I leave well enough alone and NOT update.
2. Mac OSX update to 10.5.3 (I am not having any issues now running 10.5.2}
3. Airport Utility 5.3.2 and airport base station Agent (is this what is built into my computer?]
4 iTunes 7.6.2
5. Quicktime 7.5
6 Pro Application Update 2006-02 { I do not have any of the programs that this update mentions}
Has anyone updated any of these same updates and experienced problems. Have not seen posts concerning the Radeon Update
I have been reading some posts about the 10.5.3
Just wondering if I should leave well enough alone and not do any of these. Computer has been great so far.
Thanks in advance.
Message was edited by: iJancy

These are varied and different updates that you have listed all together; one is an update for the graphic hardware on your Mac, a few are updates to Mac OS X itself and lastly there are a couple which update individual applications/technologies on your Mac.
Do you have a clone backup of your Mac's current situation? If so, with the exception of the hardware update, implementing each update individually would allow you to evaluate the update and "roll back" to your clone if it was unsatisfactory.
Bare in mind that future updates to Mac OS X or the primary applications/technologies on your Mac may well require that these previous updates have been installed. There is the possibility that Software Update will not notify/alert you of an update available because the previous update has not been installed.
I have every update/upgrade applicable to my particular iMac model installed. I have no issues and have never had any issues.

ATI Raedon HD2600 or 2600 Pro?

Hello,
My 24", 2.4 ghz aluminum iMac, purchased in August 2007, has the ATI Radeon HD2600 graphics card with 265 mb of RAM. Is this different than the ATI Radeon HD2600 Pro card that requires the firmware update?
I downloaded & installed all the appropriate updates (10.4.11, 1.2.1) and when I downloaded the firmware update & tried to install it, the machine said it did not need it.
Are there 2 cards - the HD 2600 & the HD 2600 Pro? If so, when did the "Pro" card begin to be used? My machine is only 3 months old!
bub_star

Only some of the HD 2600 cards require the update, but their specifications are all the same. Your iMac has the same video card still shipping with the iMac.... technology hasn't left you behind just yet
It seems if the Video RAM on your iMac w/HD 2600 card is from a certain vendor, THEN you need the update.
http://docs.info.apple.com/article.html?artnum=307008

ATI Radeon 9200 and Mac OS X 10.5?

I just bought this card (ATI Radeon 9200 Mac Edition - 128MB), installed the available drivers (for Mac OS X 10.4, according to ati.com) and firmware update, but the graphics are horrible. In World of Warcraft, it's running at 5 FPS at lowest graphic-settings in the game. Even the Finder is having trouble.
Doesn't this card work under Mac OS X 10.5?
I tried to contact ATI, but I haven't heard from them yet. So I'd like to hear, if anyone have the same issues as me.

Hi-
The 9200 has a core clock speed of 250mhz. Since it resides in a PCI slot, there is no multiplier, and the results are less than spectacular (as you found out). The 9200 is really meant more for adding multiple monitors, rather than adding performance.
The FX 5200(?) that came in your G5 also has a core clock speed of 250mhz, but with the 8x AGP slot, it benefits from the multiplier of the AGP, and operates much faster (though the 5200 isn't really a performance card). More on AGP.
If you are really serious about your gaming, you will need the ATI Radeon X800XT. Here are some Benchmarks. More OEM Benchmarks.
You might want to consult with OWC as to the possibility of exchange of the 9200 for an X800..... The 9600 may also be a consideration, though it is only a mid range performer.

ATI Radeon 5770 for 2008 Mac Pro

I just bought this card for my 2008 mac pro. According to the Apple store's Q&A, this card should work fine with my computer. I am curious if this is just a simple swap, or if I need to attach any additional power cable to the mother board.
Also, is it possible to use this card and the ATI Radeon HD2600 simultaneously on my computer? I have a USB card and a black magic HDMI in/out card I use for video already installed. Just want to make sure I won't pull too much power and overheat.
Thanks!

I had basically the same problem with trying to run the Mac 5770 with a Mac/PC 3870 in my 2008 Octo 3.1 MP. I was hoping I could use the component output on the 3870 (using the 9 pin ATI adapter that has component, s-video and composite outputs) for my Sony CRT Pro monitor and using the DVI to run a large screen TV for Netflicks, etc, or another smaller digital monitor. Plus, I was keeping my fingers crossed that Apple's "Color" application wouldn't see the 3850 if I had the AV switcher turning the connections off when not in use while editing in FCP Studio (Color will usually not launch if it "sees" two graphics cards connected to monitors).
Apparently the 5770 firmware has a conflict with other ATI cards: 2600, 3850 and maybe even 4870. I thought they would have a better chance of working together being ATI, but apparently not. Another user posted that he was able to get a NVIDIA GT 120 working fine with the ATI 5770 after having the same issues with the ATI 2600, but whether Color will launch is another question. I suppose I can try some older cheaper NVIDIA's maybe even some with analog outputs that the 3870 had if I could find one? Any suggestions or success stories in running a second card with the 5770?
Finally, I removed the 3870 to see how the 5770 would work by itself: the screen start-up time went from several minutes to seconds. Both monitors are very snappy and working fine with one 23" CD in the DVI port and the other23" CD using the mini-display port adapter (just the single $29 one, not dual DVI $99 type).
I don't play games or do much 3D, so I hope it was worth the upgrade price, as the 3870 had a passive cooler, was rock solid in every aspect and ran Core apps fast, but it didn't have OpenCL, so I'm hoping to see some improvement across the board in my graphics, especially the Adobe CS5 Suite.

ATI Radeon X1900 model designation - a silly question

Hi all,
I guess I reserved a silly question for for my very first discussions post!
I have a Feb 2007 vintage 2.66 Mac Pro with the ATI X1900 graphics card. When I ran software update on this machine today, it ignored the ATI X1900 XT firmware update recently posted by Apple. Upon querying my card in system profiler, I see it listed as simply "ATY,RadeonX1900"–no XT at the end. Also, both the "ATY" and the lack of a space after the comma are not typos on my part-that's exactly how they appear in system profiler-weird. It listed the device ID as: 0x1002.
Is the "XT" a more recent model of the X1900 series? I queried my serial number on Apple's specification page, and it said I should have a X1900 XT, but I suspect Apple updates these on the fly.
I really want to keep my drivers and firmware up to date, but I certainly don't want try to install an incorrect firmware update-yikes. Should I trust software update or should I manually download this update from Apple's site and install it?

Thanks, guys! This is really helpful information.
I'll go back and read the posts concerning this update. Having gone through the G4 "leaf blower" fan noise ordeal, I don't want to make my blissfully quiet MacPro any louder (and neither do my office mates).
I work in 3-D modelling and architectural graphics, and I've stepped up to the big display/high end graphics card world at the same time as my applications (formZ, SketchUp, Lightwave, CS3) are rewriting their software for Intel Macs. A few minor, but annoying, issues persist, and I was naivley hoping a simple firmware update would be the silver bullet. Yeah, right.
Maybe I'm just "pre-registering" my anxiety over Leopard...
Oh well. Chin-up! And thank you all for the quick replies!

IMac ATI Radeon HD Graphics Firmware Update 1.0.1

http://www.apple.com/support/downloads/imacatiradeonhdgraphicsfirmwareupdate101. html
I have a 24inch imac with ATI Radeon HD 2600, ROM Revision: 113-B2250F-219.
Upon trying to install the update, it says my computer doesn't need it, even though it looks like my rom is older than the version in the update (113-B2250L-259).

according to ASP on my 20inch iMac Alum;
ATI Radeon HD 2400 XT:
Chipset Model: ATI,RadeonHD2400
Type: Display
Bus: PCIe
PCIe Lane Width: x16
VRAM (Total): 128 MB
Vendor: ATI (0x1002)
Device ID: 0x94c8
Revision ID: 0x0000
ROM Revision: 113-B2250A-207
EFI Driver Version: 01.00.207
And the installer does not continue at all but just say that I do not need the update...

How to tell if an ATI Radeon Pro Graphics card needs any updates?

I have upgraded the firmware on my G4 Gigabit and re-installed the combo update for OS 10.4.11, and am on an update rampage. I am wondering if I need to update driver/firmware for the video card in this computer. It is a ATI Radeon 9000 Pro. System Profiler lists its ROM Revision as 113-99703-127.
How to tell if this needs an updated driver? Also, the ATI site lists both a download for ATI Displays Panel, and Retail Update. If I need to update, which is it, or both?
I know nothing about graphics cards.
Thanks!
BC

Hi-
The ATI Displays panel is a handy tool. Install if you like, with no worry as to adverse effects.
Other than that, Tiger has all the drivers that you need. No firmware update is needed, either.
Should be no need for outside updates for the 9000.

Updating ATI Radeon HD 2600 XT with 256MB

Hello All,
I have a early 2008 Mac Pro Quad-Core 2.66 with ATI Radeon HD 2600 XT with 256MB dual DVI. I would like to update to a newer card and was wondering what is compatable with my machine. I have 12GB of ram and I do video editing and gaming on the off time. I've seen whats out there and I read that there is only a couple of modles that is compatable with my 32bit system. I am running dual monitors so I need a dual DVI setup.
Can someone suggest a decent card that's not going to bust the bank too much. Something that will run what I need to without having to fork over $1,000 for the latest and greatest. or maybe the lowest to the highest price point.
Thanks in advance.
Johnny 5

you would be much happier with Apple's ATI 5770 $250. You do not have a 32-bit system. You don't even have 32-bit EFI (firmware).
You can spend more for higher end cards.
12GB RAM - FBDIMMs have gotten cheaper and better if you are in the market 2x2GB $30
ATI Radeon 5770
http://store.apple.com/us/product/MC742ZM/A
http://www.amazon.com/Apple-ATI-Radeon-5770-MC742ZM/dp/B003Z6QH6M
http://www.bhphotovideo.com/c/product/726537-REG/Apple_MC742ZM_A_ATI_Radeon_HD_5 770.html

ATI Radeon 9800 Pro Firmware (APPLE OEM) Display Isse

This has probibley been covered somewhere else, but.
I have a G5 with the ATI Radeon 9800 Pro, (APPLE OEM) Came installed. Recentley I've been getting diistortion on my desktop, random squares, just wierd graphics issues.
I contacted Apple, did a reinstall (Archieve and Clean) of 10.4, did everything they said, then they gave up and sent me a new card. The new card seems to have the same problms, (A little less intensley, but its there)
Does anyone know any solutions to this, is there a firmware update for this card. I already updated to drivers from the ATI site to (4.5.7) but the aug2005-radeon-universal-rom-update says it does not work on Apple OEM Cards. Any Solutions? Please HELP.
G5, 2X2.0 Ghz, (Earily Modle, June 2003)
2 GB Ram, ATI 9800 Pro

are your problems like these?
http://homepage.mac.com/jperalesgarat/PhotoAlbum6.html
(the last image)

[HOW-TO] Ati Radeon & Kernel 2.6 - Updated

[HOW-TO] Ati Radeon & Kernel 2.6
Updated on new ati-drivers 4.3.0
[CONTENTS]
1.1 Requirements
2.0 Compiling Kernel
2.1 Configuring Bootloader [GRUB]
3.0 Building & Generating modules
3.1 Pacthing modules
3.2 Compiling modules
3.3 Adding modules boot runlevel
4.0 fglrxconfig
4.1 Xorg.conf NEW!!
[1.1] Requirements
(All Intel & AMD users)
1. Ati Radeon 9xxx (Mine 9600 Sapphyre pro)
2. Kernel 2.8.x (Current 2.8.1)
3. wget, rpmunpack, cpio
4. PKGBUILD [FILE]
5. ati-drivers.install [FILE]
6. fglrx-2.6-vmalloc-vmaddr.patch New!!!
Those are code for listed files:
PKGBUILD New!!!
pkgname=ati-drivers
pkgver=3.11.1
pkgrel=1
pkgdesc="Proprietary (binary) drivers for ATI Radeon Cards."
url="www.ati.com/support/driver.html"
depends=('xfree86')
install="$pkgname.install"
source=(http://www2.ati.com/drivers/linux/fglrx-4.3.0-$pkgver.i386.rpm)
#md5sums=('9f7802ee0bbdeb5172673027056e789d')
# build-time deps: rpmunpack, cpio, gzip
build() {
cd $startdir/pkg
rpmunpack < $startdir/src/fglrx-4.3.0-$pkgver.i386.rpm | gzip -d | cpio -idmuv
chmod 755 -R .
mv opt/kde3 opt/kde
mkdir -p opt/gnome/share
mv usr/share/gnome/apps/ opt/gnome/share
rm -rf usr/share/gnome
usr/share/applnklib/modules/fglrx/{fglrx*.o,fglrx_info.txt}
usr/X11R6/bin/LICENSE.{GPL,QPL}
usr/X11R6/bin/*.bz2
ati-drivers.install New!!!
post_install() {
cat << EOF
NOTE
To create an fglrx module for your system, do:
cd /lib/modules/fglrx/build_mod
./make.sh
cd ..
./make_install.sh
Make sure you have your full kernel tree at /usr/src/linux
Then initialize "fglrxconfig" to create an XF86Config
for your graphics card.
EOF
post_upgrade() {
/bin/true
pre_remove() {
/bin/true
op=$1
shift
$op $*
fglrx-2.6-vmalloc-vmaddr.patch New!!!
--- firegl_public.c 2004-03-17 17:00:29.000000000 -0500
+++ /lib/modules/fglrx/build_mod/firegl_public.c 2004-07-18 16:09:46.000000000 -0500
@@ -2010,8 +2010,8 @@
pMmPage = virt_to_page(kaddr);
#endif /* LINUX_VERSION_CODE < 0x020400 */
- atomic_inc(&(pMmPage->count)); /* inc usage count of page */
+// atomic_inc(&(pMmPage->_count)); /* inc usage count of page */
+ get_page(pMmPage);
#if LINUX_VERSION_CODE >= 0x020400
// __KE_DEBUG3("vm-address 0x%08lx => kernel-page-address 0x%pn",
// address, page_address(pMmPage));
[2.0] Compiling kernel
<*> MTRR
e poi
<M> /dev/agpgart (AGP Support)
< > ALI chipset support
< > ATI chipset support
< > AMD Irongate, 761, and 762 chipset support
< > AMD Opteron/Athlon64 on-CPU GART support
< > Intel 440LX/BX/GX, I8xx and E7x05 chipset support
< > Intel i865 chipset support
< > NVIDIA nForce/nForce2 chipset support
< > SiS chipset support
< > Serverworks LE/HE chipset support
<M> VIA chipset support
< > Transmeta Efficeon support
[*] Direct Rendering Manager (XFree86 4.1.0 and higher DRI support)
< > 3dfx Banshee/Voodoo3+
< > 3dlabs GMX 2000
< > ATI Rage 128
< > ATI Radeon
< > Matrox g200/g400
< > SiS video cards
make dep && make clean bzImage modules modules_install
[/code]
when finished,mount boot partition (if not already mounted)
[code]
mount /boot
[/code]
and copy kernel image to the boot directory, so the new kernel loads after computer restart. Pay attention to not overwrite existent kernels images in boot partition. For security issues rename it as ***_new.
[code]
cp arch/i386/boot/bzImage /boot/vmlinuz_new
[/code]
[2.1] Configuring Bootloader [GRUB]
Edit your boot-loader config file.
I currently use grub instead of lilo.
[code]
nano /boot/grub/menu.lst
[/code]
Add a new sub-menu (this is an example) Check on the forum how to set-up a bootloader).
[code]
# (0) Arch Linux
title Arch Linux [/boot/vmlinuz_new]
root (hd0,3)
kernel (hd0,1)/vmlinuz_new root=/dev/discs/disc0/part4 ro
[/code]
REBOOT
[3.0] Building ati-drivers
Make a directory under /var/abs/local called ati
[code]
mkdir /var/abs/loca/ati
[/code]
copy in it the two files PKGBUILD ati-drivers.install
[code]
cp /path/to/file/PKGBUILD /var/abs/local/ati
cp /path/to/file/ati-drivers.install /var/abs/local/ati
[/code]
start building package
[code]
makepkg -c
[/code]
if all goes well, this will be the output
[code]
[root@CippaLippa ati]# makepkg -c
==> Making package: ati-drivers
==> Checking Runtime Dependencies...
==> Checking Buildtime Dependencies...
==> Retrieving Sources...
==> .......
==> .......
==> Compressing man pages...
==> Stripping debugging symbols from libraries...
==> Stripping symbols from binaries...
==> Generating .PKGINFO file...
==> Copying install script...
==> Generating .FILELIST file...
==> Compressing package...
==> Cleaning up...
==> Finished making: ati-drivers (Tue Feb 10 15:11:13 CET 2004)
[root@CippaLippa ati]#
[/code]
It downloads necessary files and generates a file called ati-drivers-3.9.x.pkg.tar.gz
Install it using:
[code]
pacman -A ati-drivers-3.x.x.pkg.tar.gz
[/code]
This installation generates a folder in /lib/modules/fglrx
Change directory
[code]
cd /lib/modules/fglrx
[/code]
[3.1] Pacthing modules
To patch modules simply copy the two files .patch listed on top in this directory. Intel users must only install fglrx-2.6-vmalloc-vmaddr.patch, AMD users both.
[code]
cp /path/to/patch/fglrx-2.6-vmalloc-vmaddr.patch /lib/modules/fglrx
[/code]
change directory
[code]
cd build_mod
[/code]
to patch the file firegl_public.c
[code]
patch -b firegl_public.c ../fglrx-2.6-vmalloc-vmaddr.patch
[/code]
It's time to compile the modules
[code]
sh make.sh
[root@CippaLippa build_mod]# sh make.sh
ATI module generator V 2.0
==========================
initializing...
probing for VMA API version...
cleaning...
patching...
make[1]: Leaving directory `/usr/src/linux-2.6.x
build succeeded with return value 0
duplicating results into driver repository...
done.
==============================
You must change your working directory to /lib/modules/fglrx
and then call ./make_install.sh in order to install the built module.
==============================
[/code]
change directory as you see on screen
[code]
cd /lib/modules/fglrx
[/code]
and compile in
[code]
sh make_install.sh
[/code]
if will be no errors in output, module fglrx were perfectly compiled in /lib/modules/2.6.x/kernel/drivers/char/drm/ and named "fglrx.ko"
[3.2] Adding modules boot runlevel
open /etc/rc.conf
[code]
nano /etc/rc.conf
[/code]
go to line MODULES= and add
[code]
agpgart via-agp fglrx rtc <== make sure always in this order
[/code]
(if your motherboard is "VIA" equipped, else check what do you have: the same configured in kernel under /dev/agpgart (AGP Support)
[4.0] fglrxconfig
Ati-drivers comes with a modified xf86config, utility to generate XF86config files.
Run
[code]
fglrxconfig
[/code]
and a welcome screen appear
[code]
==============================================================================
ATI - FIRE GL - BE THE CREATOR
==============================================================================
This program will create the ATI "XF86Config-4" file
- based on your selections - for the below listed boardtypes...
- ATI Radeon 8500 / 9100
- ATI FireGL 8700 / 8800 / E1
- ATI FireGL T2
- ATI Radeon 9000
- ATI Radeon 9200
- ATI Radeon 9500
- ATI Radeon 9600
- ATI Radeon 9700
- ATI Radeon 9800
- ATI FireGL Z1 / X1 / X2
- ATI Mobility M9
- ATI Mobility FireGL 9000
- ATI Mobility M9PLUS
The "XF86Config-4" file usually resides in /etc/X11.
Press [Enter] to continue, press 'q'&[Enter] or [Ctrl]+'c' to abort.
[/code]
follow the on-screen steps leaving default settings. Configure only mouse, keyboard, screen frequencies and resolution. At least when prompt for:
[code]
External AGPGART module:
external agpgart module execute this on the commandline (as root):
/sbin/insmod agpgart
or alternatively configure your system to auto load the module.
Do you want to use the external AGP GART module (y/n)? [y]
[/code]
be sure to answer "YES".
[4.1] Xorg.cong New!!!
Xorg configuration file, resides in /etc/X11.
It is XF86config renamed and Will replace soon it, with the new video system based on Xorg.
This is my xorg.conf file:
[code]
Section "dri"
Mode 0666
EndSection
Section "Module"
Load "dbe" # Double buffer extension
SubSection "extmod"
Option "omit xfree86-dga" # don't initialise the DGA extension
EndSubSection
Load "type1"
Load "freetype"
Load "glx" # libglx.a
Load "dri" # libdri.a
EndSection
Section "Files"
RgbPath "/usr/X11R6/lib/X11/rgb"
FontPath "/usr/X11R6/lib/X11/fonts/local/"
FontPath "/usr/X11R6/lib/X11/fonts/misc/"
FontPath "/usr/X11R6/lib/X11/fonts/100dpi/:unscaled"
FontPath "/usr/X11R6/lib/X11/fonts/75dpi/:unscaled"
FontPath "/usr/X11R6/lib/X11/fonts/Type1/"
FontPath "/usr/X11R6/lib/X11/fonts/Speedo/"
FontPath "/usr/X11R6/lib/X11/fonts/100dpi/"
FontPath "/usr/X11R6/lib/X11/fonts/75dpi/"
ModulePath "/usr/X11R6/lib/modules"
EndSection
Section "InputDevice"
Identifier "Keyboard1"
Driver "Keyboard"
Option "AutoRepeat" "500 30"
Option "XkbRules" "xfree86"
Option "XkbModel" "pc105"
Option "XkbLayout" "it"
EndSection
Section "InputDevice"
Identifier "Mouse1"
Driver "mouse"
Option "Protocol" "ImPS/2"
Option "ZAxisMapping" "4 5"
Option "Device" "/dev/usbmouse"
EndSection
Section "Monitor"
Identifier "Monitor0"
HorizSync 31-96
VertRefresh 55-160
Option "DPMS"
EndSection
Section "Device"
Identifier "Standard VGA"
VendorName "Unknown"
BoardName "Unknown"
EndSection
Section "Device"
Identifier "ATI Graphics Adapter"
Driver "fglrx"
#Option "NoDDC"
Option "no_accel" "no"
Option "no_dri" "no"
Option "DesktopSetup" "0x00000000"
Option "MonitorLayout" "AUTO, AUTO"
Option "IgnoreEDID" "off"
Option "HSync2" "unspecified"
Option "VRefresh2" "unspecified"
Option "ScreenOverlap" "0"
Option "NoTV" "yes"
Option "TVStandard" "NTSC-M"
Option "TVHSizeAdj" "0"
Option "TVVSizeAdj" "0"
Option "TVHPosAdj" "0"
Option "TVVPosAdj" "0"
Option "TVHStartAdj" "0"
Option "TVColorAdj" "0"
Option "GammaCorrectionI" "0x00000000"
Option "GammaCorrectionII" "0x00000000"
Option "Capabilities" "0x00000000"
Option "VideoOverlay" "on"
Option "OpenGLOverlay" "off"
Option "CenterMode" "off"
Option "PseudoColorVisuals" "off"
Option "Stereo" "off"
Option "StereoSyncEnable" "1"
Option "FSAAScale" "1"
Option "FSAADisableGamma" "no"
Option "FSAACustomizeMSPos" "no"
Option "FSAAMSPosX0" "0.000000"
Option "FSAAMSPosY0" "0.000000"
Option "FSAAMSPosX1" "0.000000"
Option "FSAAMSPosY1" "0.000000"
Option "FSAAMSPosX2" "0.000000"
Option "FSAAMSPosY2" "0.000000"
Option "FSAAMSPosX3" "0.000000"
Option "FSAAMSPosY3" "0.000000"
Option "FSAAMSPosX4" "0.000000"
Option "FSAAMSPosY4" "0.000000"
Option "FSAAMSPosX5" "0.000000"
Option "FSAAMSPosY5" "0.000000"
Option "UseFastTLS" "0"
Option "BlockSignalsOnLock" "on"
Option "UseInternalAGPGART" "no"
Option "ForceGenericCPU" "no"
BusID "PCI:1:0:0" # vendor=1002, device=4150
Screen 0
EndSection
Section "Screen"
Identifier "Screen0"
Device "ATI Graphics Adapter"
Monitor "Monitor0"
DefaultDepth 24
#Option "backingstore"
Subsection "Display"
Depth 24
Modes "1280x1024" "1024x768" "800x600"
ViewPort 0 0 # initial origin if mode is smaller than desktop
EndSubsection
EndSection
Section "ServerLayout"
Identifier "Server Layout"
Screen "Screen0"
InputDevice "Mouse1" "CorePointer"
InputDevice "Keyboard1" "CoreKeyboard"
EndSection
[/code]
REBOOT
Start in X with kde, gnome or othet window manager.
If X does not start you maybe made something wrong, retry from the beginning. Else if it starts, check if DRI os working
[code]
fgl_glxgears
[/code]
if it is working, a rotating cube will appear in a new windows, and if it is so.....
ENJOY
**SORRY FOR MY ENGLISH **

Using kernel 2.6.2
I'm starting over again but now cannot get the PKGBUILD to complete. I had this problem this morning as well, but after editing the PKGBUILD file did eventually get it to complete. This is the output of makepkg -c using the PKGBUILD as posted:
[root@Arch2 ati]# makepkg -c
==> Making package: ati-drivers (Wed Feb 11 16:11:02 GMT 2004)
==> Checking Runtime Dependencies...
==> Checking Buildtime Dependencies...
==> Retrieving Sources...
==> Downloading fglrx-glc22-4.3.0-3.2.8.i586.rpm
--16:11:02-- http://www2.ati.com/drivers/linux/fglrx … 8.i586.rpm
=> `fglrx-glc22-4.3.0-3.2.8.i586.rpm'
Resolving www2.ati.com... 62.25.100.58, 62.25.100.32
Connecting to www2.ati.com[62.25.100.58]:80... connected.
HTTP request sent, awaiting response... 200 OK
Length: 4,365,039 [audio/x-pn-realaudio-plugin]
100%[====================================>] 4,365,039 55.23K/s ETA 00:00
16:12:27 (50.80 KB/s) - `fglrx-glc22-4.3.0-3.2.8.i586.rpm' saved [4365039/4365039]
==> Validating source files with MD5sums
fglrx-glc22-4.3.0-3.2.8.i586.rpm ... Passed
==> Extracting Sources...
==> Removing existing pkg/ directory...
==> Starting build()...
./lib/modules/fglrx/build_mod/2.6.x/Makefile
./lib/modules/fglrx/build_mod/agp.h
./lib/modules/fglrx/build_mod/agp3.c
./lib/modules/fglrx/build_mod/agp_backend.h
./lib/modules/fglrx/build_mod/agpgart.h
./lib/modules/fglrx/build_mod/agpgart_be.c
./lib/modules/fglrx/build_mod/firegl_public.c
./lib/modules/fglrx/build_mod/firegl_public.h
./lib/modules/fglrx/build_mod/i7505-agp.c
./lib/modules/fglrx/build_mod/libfglrx_ip.a.GCC2
./lib/modules/fglrx/build_mod/libfglrx_ip.a.GCC3
./lib/modules/fglrx/build_mod/make.sh
./lib/modules/fglrx/build_mod/nvidia-agp.c
./lib/modules/fglrx/fglrx.2.4.18-17.7.x.o
./lib/modules/fglrx/fglrx.2.4.18-17.8.0.o
./lib/modules/fglrx/fglrx.2.4.20-6-SMP.o
./lib/modules/fglrx/fglrx.2.4.20-6.o
./lib/modules/fglrx/fglrx.2.4.21-1.1931.2.349.2.2.ent-SMP.o
./lib/modules/fglrx/fglrx.2.4.21-1.1931.2.349.2.2.ent.o
./lib/modules/fglrx/fglrx.2.4.21-1.1931.2.349.2.2.entbigmem-SMP.o
./lib/modules/fglrx/fglrx_info.txt
./lib/modules/fglrx/make_install.sh
./opt/kde3/share/applnk/fireglcontrol_kde3.desktop
./usr/X11R6/bin/LICENSE.GPL
./usr/X11R6/bin/LICENSE.QPL
./usr/X11R6/bin/fgl_glxgears
./usr/X11R6/bin/fglrx_xgamma
./usr/X11R6/bin/fglrxconfig
./usr/X11R6/bin/fglrxinfo
./usr/X11R6/bin/fireglcontrol.qt2.gcc2.96.bz2
./usr/X11R6/bin/fireglcontrol.qt3.gcc3.2.bz2
./usr/X11R6/bin/fireglcontrol.qtstatic.gcc2.96.bz2
./usr/X11R6/include/X11/extensions/fglrx_gamma.h
./usr/X11R6/lib/libGL.so.1.2
./usr/X11R6/lib/libfglrx_gamma.a
./usr/X11R6/lib/libfglrx_gamma.so.1.0
./usr/X11R6/lib/modules/dri/fglrx_dri.so
./usr/X11R6/lib/modules/drivers/fglrx_drv.o
./usr/X11R6/lib/modules/linux/libfglrxdrm.a
./usr/include/GL/glxATI.h
./usr/share/applnk/fireglcontrol.kdelnk
./usr/share/gnome/apps/fireglcontrol.desktop
./usr/share/icons/ati.xpm
./usr/share/pixmaps/ati.xpm
./usr/src/ATI/fglrx_panel_sources.tgz
./usr/src/ATI/fglrx_sample_source.tgz
21763 blocks
/usr/bin/makepkg: line 23: usr/share/applnklib/modules/fglrx/fglrx*.o: No such file or directory
usr/X11R6/bin/LICENSE.GPL: line 2: syntax error near unexpected token `('
usr/X11R6/bin/LICENSE.GPL: line 2: ` The Qt GUI Toolkit is Copyright (C) 1994-2000 Trolltech AS.'
/usr/bin/makepkg: line 25: usr/X11R6/bin/fireglcontrol.qt2.gcc2.96.bz2: cannot execute binary file
==> ERROR: Build Failed. Aborting...
[root@Arch2 ati]#
I seem to be going backwards!

ATi Radeon HD2600 firmware update

Similar Messages

Maybe you are looking for