Ati tv wonder

I installed aa ATI tv wonder pro.When I run the pc check in multimedia center configuration I get an error that says that my sound card did not pass the test: the clock accuracy is less than .2%. I downloaded the latest drivers for my audigy eax soundblaster sound card but it did not solve the problem. I would appreciate if anyone could help me. Thank you!

don't bother, it's always that with the ATI stability test.

Similar Messages

ATI TV Wonder... not making device node?

I purchased an ATI TV Wonder card yesterday. I've been Googling and reading numerous tutorials and I just can't get it to work. There just isn't a device node for it in /dev... no /dev/video0, /dev/v4l/video0, not even a /dev/v4l!
So far, I've changed my /etc/modprobe.conf so that it includes:
alias char-major-89 i2c-dev
alias char-major-81 videodev
alias char-major-81-0 bttv
options bttv card=63 radio=0
options tuner debug=1
alias char-major-81-1 tvaudio
After rebooting, an lsmod showed that none of those were loaded, so I added them (bttv, tuner, tvaudio, i2c_core, and i2c_algo_bit) to /etc/rc.conf as well. Now they are loaded at boot, but there's still no device.
Then, I edited /etc/X11/xorg.conf to load v4l, but that doesn't help either. I also added:
REGISTER v4l/.* PERMISSIONS root.users 660
REGISTER video0 PERMISSIONS root.users 660
to /etc/devfsd.conf (and rebooted to restart devfs), but that didn't help, either.
What do I have to do to get the device to show up? It shows up in lspci (I think):
[kyle@zero ~]$ lspci
00:00.0 Host bridge: nVidia Corporation: Unknown device 01e0 (rev c1)
00:00.1 RAM memory: nVidia Corporation: Unknown device 01ea (rev c1)
00:00.2 RAM memory: nVidia Corporation: Unknown device 01ee (rev c1)
00:00.3 RAM memory: nVidia Corporation: Unknown device 01ed (rev c1)
00:00.4 RAM memory: nVidia Corporation: Unknown device 01ec (rev c1)
00:00.5 RAM memory: nVidia Corporation: Unknown device 01ef (rev c1)
00:01.0 ISA bridge: nVidia Corporation: Unknown device 0060 (rev a4)
00:01.1 SMBus: nVidia Corporation: Unknown device 0064 (rev a2)
00:02.0 USB Controller: nVidia Corporation: Unknown device 0067 (rev a4)
00:02.1 USB Controller: nVidia Corporation: Unknown device 0067 (rev a4)
00:02.2 USB Controller: nVidia Corporation: Unknown device 0068 (rev a4)
00:04.0 Ethernet controller: nVidia Corporation: Unknown device 0066 (rev a1)
00:06.0 Multimedia audio controller: nVidia Corporation nForce MultiMedia audio [Via VT82C686B] (rev a1)
00:08.0 PCI bridge: nVidia Corporation: Unknown device 006c (rev a3)
00:09.0 IDE interface: nVidia Corporation: Unknown device 0065 (rev a2)
00:1e.0 PCI bridge: nVidia Corporation: Unknown device 01e8 (rev c1)
01:07.0 Multimedia video controller: Conexant: Unknown device 8800 (rev 05)
01:0a.0 Ethernet controller: D-Link System Inc DL10050 Sundance Ethernet (rev 12)
02:00.0 VGA compatible controller: ATI Technologies Inc Radeon R250 If [Radeon 9000] (rev 01)
02:00.1 Display controller: ATI Technologies Inc Radeon R250 [Radeon 9000] (Secondary) (rev 01)
I know it's supported because it was working on Ubuntu (but after the dependency hell I went through trying to get kdetv to install I reinstalled Arch). I'm at a loss here... I have no idea what to do next. Anyone have any suggestions?

undeadpenguin wrote:
I purchased an ATI TV Wonder card yesterday. I've been Googling and reading numerous tutorials and I just can't get it to work. There just isn't a device node for it in /dev... no /dev/video0, /dev/v4l/video0, not even a /dev/v4l!
So far, I've changed my /etc/modprobe.conf so that it includes:
alias char-major-89 i2c-dev
alias char-major-81 videodev
alias char-major-81-0 bttv
options bttv card=63 radio=0
options tuner debug=1
alias char-major-81-1 tvaudio
I'm at a loss here... I have no idea what to do next. Anyone have any suggestions?
I've no idea whether this has anything to do with your problem but I noticed that in your /etc/modprobe.conf you've missed your tuner type.
you have:
options bttv card=63 radio=0
options tuner debug=1
I think you should have something like:
options bttv card=63 radio=0
options tuner=5 debug=1
(replace 5 with your tuner type code)
.murkus

Other remotes in an AirPort Express - ATI Remote Wonder?

I've just bought an AirPort Express, looks like a good little product, but just wondering about plugging my USB remote into it.
I've got an ATI Remote Wonder, which has a small USB receiver, and wondered if there is ever likely to be any support for using this with the AirPort, through the printer port? I know that there is the Apple remote available, but would prefer to use mine (radio frequency wireless rather than infrared).
Does anyone rate my chances of getting it to work / someone writing a software update to support it?
Cheers
David

Errr... that was about Client Mode, not connecting remotes to it.
As far as I can tell from a lot of time looking from Google, there isn't any support for it currently (neither official nor third party). I've tried to do the Feedback suggested to Apple, but there wasn't a category for AirPorts so no idea if they'll ever get it through the laptop Feedback link I used :o(
Alternatively, maybe if I tape the transmitter to my laptop it'll work too... just not quite as elegant a solution!
David

Ati tv wonder video capture card

Recently purchased ATI tv wonder hd 650 usb. The guy at the electronics store told me that it would probably work with mac. I looked online and found to my dismay that there is a separate model for mac. http://ati.amd.com/products/tvwonder650/usbmac/index.html
as opposed to the one i purchased.
http://ati.amd.com/products/tvwonder650/usb/index.html
My question for you knowledgeable people is this: what is stopping the pc version from working with my macbook?
the actual devices appear exactly the same, except one is black and one is white.
is it possible to get it working?
if not, can you recommend another external capture card?

The El Gate EyeTV products work quite well. The ATI product won't work without Mac software compatible with the card and the card would need Mac compatible firmware. I doubt there is any way to get the ATI product to work on your computer, but the best way to find out is to contact ATI's tech support.

ATI TV Wonder 650 And FME

Hi I'm using ATI TV Wonder 650 Capture Card..
When I use FME the only thing i get is two green screens on
both sides..,Is There a setting I'm have to have FME On..
Im Casting My Video Games To Justin.tv..
Thank You..

What type of input you are giving to the card? SVideo or
Coaxial? You need to select type of input from advance property
page of device(wrench icon adjacent to Video device drop down
list). If it is SVideo or TV Input. If it is TV input then you need
to select channel also on which you are getting the signal.

ATI Remote Wonder

Does anyone have an ATI Remote Wonder working after Leopard installation? Mine worked on my Intel iMac before Leopard, but not now.

Hi Nanobu,
One option would be to use the VISA Driver Development wizard to assign NI-VISA as the driver for the remote. This option requires you to have VERY detailed knowledge about the remote, and will not be trivial . One question though. Does the remote mimic keystrokes on your keyboard when you push a button? If it does, then you can use LabVIEW directly to capture the keystrokes and determine what button was pushed on the remote. This will probably be a more feasible solution. Hope this helps.
Regards,
Ebele O.
National Instruments

Ati TV Wonder Ve

is their and drivers or a way to use the windows drivers on my ATI TV Wonder VE. I bought it some time ago and when I switch over to mac I never got it to work. I heard of ways of using windows drivers on linux with wireless cards I wasn't sure if this would work for Mac as well.
-Mac OS X 10.2.8

I'm not using SP-1, so that's not the problem. I just downloaded the trial version of PowerVCR II, but basically the same thing happens as under MSIPVS Windrv - splash screen and then it stops dead.
In poking around in the Device Mgr, I do have one question maybe someone can answer. Under the entries for the MSI PVS Tuner, Crossbar, and Video Capture - under the Driver details, the following files are listed (in addition to the basic CX88 MSI drivers.
ks.sys
lyuv_32.dll
ksproxy.ax
kstvtune.ax
ksuser.dll
kswdmcap.ax
ksxbar.ax
msh263.drv
msyuv.dll
tsbyuv.dll
vfwwdm32.dll
The files are all version 5.1.2600.0 with the exception of msh263.drv which is version 4.4.3400
I tried looking up those files in the knowledge base at microsoft, and the only references I see to any of those files are under Windows 98, not XP. I'm starting to wonder that since I upgraded from Win98 to XP instead of doing a totally clean install, that these driver files came along for the ride and now are messing things up. (I know I'm probably grasping at straws). So if anyone of you who have a working @nywhere, I would appreciate it if you could take a look.
bobk

MSI Theater 550 PRO-E vrs ATI TV Wonder Elite

I would like to know which is a better product in terms of TV resolution on the Computer Monitor and recording: ATI TV Wonder Elite or MSI 550 Pro-E ? I understand MSI 550 Pro-E uses the same video chip which is used in ATI TV Wonder Elite. What about the TV tuner and its TV quality on the monitor and recording results ? Which is a better product ? Has anyone out there used both the products and compared them ? I am planning to get one of these but cannot make up my mind. Moreover, MSI tuner card is much cheaper when compared with ATI card :$40 less. I want to be sure that I am getting a good product or why bother to spend $40 more.

if they both use the same ATI Theater 550PRO chipset, then i imagine performance will be pretty much the same

ATI AIW vs ATI TV Wonder Pro

I have done searches for this before but never found anything. I used to have an All in wonder series video card but I did not like the price jump to get a newer card so I decided after much research to go with the TV Wonder Pro but there is one thing I cannot figure out to get enabled (if it is even possible!) With the AIW I could pause TV because it would always record whatever you were currently watching. With the seperate card it no longer does this feature. I used it all the time and I cannot figure out how to enable this feature.
Any help would be greatly appreciated.

Okay I installed the new mmc and catalyst drivers from ati with no luck for the "tivo" feature. (I guess I will need to call ati and hopefully get somewhere with them). But I have run into a problem. This could be a number of different things and I am slowly trying to figure it out.
Recently I had to do a repair on Windows XP on my machine. As most of you probably know when you do a repair you need to reinstall service packs. I decided to try SP2. About the same time I installed my soundblaster Audigy Card. Now when I watch TV the audio has a reverberating sound and the video will freeze after a couple of minutes, but the audio will still keep going. Most likely this is from SP2 but it could be related to my soundcard. Also when I do the PC Check it comes back saying that Directx is not installed (I have 9.0c installed from SP2) and that my capture drivers are not installed.
I have downloaded some more files from ATI and will try those tonight and if that doesn't work I will pull the sound card then as a last resort (before removing SP2) call ATI. The reason I don't want to pull SP2 is I haven't had any other problems with it. And I like the security features it incorperates into Internet Explorer.
Anyway I will post my findings when I get a chance.

ATI Remote Wonder (Eye TV)

OS 10.4.4 "killed" my remote control "Remote Wonder" from ATI which I got together with ElGato EyeTV. It was so usefull for me (lazy couch potato) to watch EyeTV recordings, my holiday videos, my photos and listen to iTunes from the couch. I have tried everything to get it going again, even installed a clean new OS 10.4.4 on an empty external FW drive, whatever I do - none of the drivers from ATI are installable - 10.4.4 does not "want them". My new G5 Quadra and I are very sad ...
Roland Muehlberger, Linz, Austria
G5 Quadra 2,5 GHz Mac OS X (10.4.4)

Hi Nanobu,
One option would be to use the VISA Driver Development wizard to assign NI-VISA as the driver for the remote. This option requires you to have VERY detailed knowledge about the remote, and will not be trivial . One question though. Does the remote mimic keystrokes on your keyboard when you push a button? If it does, then you can use LabVIEW directly to capture the keystrokes and determine what button was pushed on the remote. This will probably be a more feasible solution. Hope this helps.
Regards,
Ebele O.
National Instruments

ATI Remote Wonder LabVIEW drivers

Hello!
if someone has some drivers for The Remote Wonder that could be really helpfull for me.
Thanks

Hi Nanobu,
One option would be to use the VISA Driver Development wizard to assign NI-VISA as the driver for the remote. This option requires you to have VERY detailed knowledge about the remote, and will not be trivial . One question though. Does the remote mimic keystrokes on your keyboard when you push a button? If it does, then you can use LabVIEW directly to capture the keystrokes and determine what button was pushed on the remote. This will probably be a more feasible solution. Hope this helps.
Regards,
Ebele O.
National Instruments

ATI TV Wonder LE and MSi K7T Mobo - major problems

Has anyone got this combination to work properly or got any tips? My machine crashes all the time (hangs up) when I am using the ATI tuner card.
System spec:
MSi K7T mobo KT133 chipset
ATI 128 Rage pro 32MB graphics card
AMD Athlon 1.2 GHz (200 FSB)
384 MB SDRAM PC133
IBM 80G Deskstar 120GXP HDD

I doubt it's something that's too slow but rather a conflict of sorts.
I heared befor of problems with the ATI AIW but have no experiance with the cards myself so I don't have any specific suggestions regarding the card.

ATi Remote Wonder remapping

Anyone know how? The remote is detected and Arch accepts input from it, but the mapping is all off. Debian had things like the volume controls mapped correctly, but in Arch pretty much nothing except the cursor movement works properly. I'd love to get this thing mapped better if anyone knows how.

Hi Nanobu,
One option would be to use the VISA Driver Development wizard to assign NI-VISA as the driver for the remote. This option requires you to have VERY detailed knowledge about the remote, and will not be trivial . One question though. Does the remote mimic keystrokes on your keyboard when you push a button? If it does, then you can use LabVIEW directly to capture the keystrokes and determine what button was pushed on the remote. This will probably be a more feasible solution. Hope this helps.
Regards,
Ebele O.
National Instruments

ATI tvPortal green screen after 10.6.2 update

After updating my MacBook Pro to 10.6.2, when I run ATI tvPORTAL the TV display is green. I have an ATI TV Wonder 650 USB for Mac. It was working fine before (10.6.1). Anyone else having problems?

Same thing here. I already had OS X 10.6.2 and when I installed the original drivers for the TV tuner fm the CD that was included, I had good audio and marginal video. I ran the auto-update on the software and downloaded/installed the latest version of the ATI drivers. That resulted in the same problem everyone else has listed: green screen and audio on all channels. I too tried to back out the update and reinstall the original drivers and now have crappy video and no audio. Tried calling ATI and their help line refers you to a former component supplier who informed me they have no visibility on the Mac drivers for the new ATI tv tuners, and suggested I contact Apple.
It would be ideal if someone could come up with the fix on this issue.

ATI TV Tuner No Audio

I am using FME with my ATI TV Tuner. The tuner has an audio
out line which connects to your sound cards line in. However the
audio out on the TV tuner will only output audio when the TV tuner
is in use. Applications like Windows Media Encoder, etc work fine.
I get audio.
However with the flash player webcam code the audio for the
TV tuner never worked, and does not work for FME as well. I get
video fine, all works there but the audio is never kicked on. I'm
not sure if there is something in the capture API for devices to
trigger the audio that FME is not doing but Windows Media Encoder
does. I am selecting all the same options I do for the capture
devices for video & audio in other applications but FME just
doesn't kick the audio out on the TV tuner thus the line in on the
sound card never gets anything.
I am running the following:
Athlon 4000+ X2 Dual Core
3 GB RAM
ATI TV WONDER PRO Capture Card
Thanks and take care.

i noticed on my sb audigy 2zs it said you cold use aux in, cdin or digital in
it took it as not both..
try to see if you flipped cable over, one of my cd cables is not keyed it could be the problem..try to email ati tech support and if it works post here please.
what drivers are you using ati cat 4.3? mabey they changed something and it made aiw stop working, sometimes change is not for the better

Ati tv wonder

Similar Messages

Maybe you are looking for