Attempting To Copy To Disk Failed. Not Enough Memory.

I am syncing my iPhone 8GB 3G with latest software to my iTunes. I keep getting the message, 'Attempting To Copy To Disk "Mackenzie's iPhone" Failed. There Is Not Enough Memory Available.' There is clearly enough room for all these song's. All help would be appreciated.
Thank's in advance,
Mackenzie.

i had a similar problem when my syn wasnt done properly before,
there isnt any real way to fix this apart from doing a restore through itunes,
once you done the restore you should be fine...

Similar Messages

Attempting to copy to disk failed.

I was using my iPod in cold weather the other night. The battery died and when it warmed back up the screen was in grayscale and it was in "disk mode". I have since restored it several times and am trying to sync it with iTunes. I keep getting an error message "Attempting to copy to disk failed. You do not have enough access privileges for this operation". The iPod was syncing just fine prior to the cold crash. I tried changing the permissions in my iTunes music library and xml file. Help?

First, reset the iPod
http://support.apple.com/kb/HT1320
and restart the Mac with the iPod connected; then try it again.
If that does not help, connect the iPod to the Mac. With iTunes not running, run Disk Utility. Does the iPod's hard drive appear in the Disk Utility sidebar? If so, select the iPod's DRIVE, not the volume indented under the drive, in the sidebar and go to the Erase tab. Set the format type to +Mac OS Extended (Journaled)+ and erase the iPod's drive.
If the erase completes successfully, quit Disk Utility and run iTunes. Immediately use the Restore button to install and initialize the iPod's software. You can then set it up and sync it as desired.

When synching my IPhone 3Gs I now get a sign "Attempting to copy to Disk failed. The required disk cannot be found." This is after synching a new Iphone 4s.. Help!!

When attempting to synch my IPhone 3Gs I now get a sign "Attempting to copy to Disk failed. The required disk cannot be found."
This is after synching a new Iphone 4s and having received some help from Apple Support who assisted with some setting
changes. Unfortunately this was over a protracted period of time and I cannot recall what was changed. Apparently my 3Gs is out of
its warranty and so they cannot help me unless I pay £25....
Can anyone help??
Johnm2429

Well, attempted again today and now my iTunes locks up whenever I select a song! Also, my Volume Mixer on my Windows 7 will not open. Just terrific. Where's my MacBook???????????????

Help with an Error "Attempting to copy to disk failed"

In the middle of udating my ipod, I receive an error message that states "Attempting to copy to disk failed. An unknown error occurred (-124)". I have tried the 5 R's and all I did was loose all the musice that was initially stored on the ipod....Does anyone have any idea how to fix this error....Any help would be appreciated.
HP Windows XP Ipod with click wheel

Thats not your exact model. Click the link below and roll down to "Method 3: Manually Locate Product Name and Number"
In that picture you see where it says "ze2001xx" right above the word warrenty, thats the model number I need
http://h10025.www1.hp.com/ewfrf/wc/genericDocument?docname=c00033108&product=180 73&lc=en&dest_page=product&cc=us

Reproducible error when loading many reports (Load report failed - Not enough memory for operation)

Environment:
Win 7 SP 1
Visual Studio Pro 2012 Update 4
Crystal Reports for Visual Studios Service Pack 10 (13.0.10.1385)
Report created in Crystal Reports XI Release 2 (11.5.8.826)
Targeting x86 .NET 4.0
Scenario:
We have a program that runs and creates a large number of reports before the process is ended. When running after many hours we'd get a Load report failed/Not enough memory of operation exception. I kept removing code and found i could reproduce just using the report.Load call. I simplified the report to a completely blank report to make sure it was nothing specific to a report I was loading. (Opened Crystal Reports XI Release 2, Save As, "Blank.rpt".). I then created, loaded, and disposed of this report in a loop. I was able to cause the same exception after 32,764 iterations on my machine. I also tried using .NET 3.5 same result. I added a counter to our main program and it also went through 32,764 report loads before the same exception was thrown. Main program uses 15 or so different reports with a variable number of subreports in each.
Sample Code to illustrate the problem:
I did this as a WinForms project since our main program is using winforms.
References added:
CrystalDecisions.CrystalReports.Engine
CrystalDecisions.ReportSource
CrystalDecisions.Shared
CrystalDecisions.Windows.Forms
using System;
using System.Windows.Forms;
using CrystalDecisions.CrystalReports.Engine;
namespace CrystalTest
    public partial class Form1 : Form
        public Form1()
            InitializeComponent();
            int i = 0;
            try
                while (true)
                    i++;
                    ReportDocument report = new ReportDocument();
                    report.Load("Blank.rpt");
                    report.Close();
                    report.Dispose();
            catch(Exception ex)
                MessageBox.Show(i.ToString() + ex.Message);
Exception:
CrystalDecisions.Shared.CrystalReportsException: Load report failed. ---> System.Runtime.InteropServices.COMException (0x80041004):
Not enough memory for operation.
   at CrystalDecisions.ReportAppServer.ClientDoc.ReportClientDocumentClass.Open(Object& DocumentPath, Int32 Options)
   at CrystalDecisions.ReportAppServer.ReportClientDocumentWrapper.Open(Object& DocumentPath, Int32 Options)
   at CrystalDecisions.ReportAppServer.ReportClientDocumentWrapper.EnsureDocumentIsOpened()
   --- End of inner exception stack trace ---
   at CrystalDecisions.ReportAppServer.ReportClientDocumentWrapper.EnsureDocumentIsOpened()
   at CrystalDecisions.CrystalReports.Engine.ReportDocument.Load(String filename, OpenReportMethod openMethod, Int16 parentJob)
   at CrystalDecisions.CrystalReports.Engine.ReportDocument.Load(String filename)
   at CrystalTest.Form1..ctor() in c:\Test Projects\CrystalTest\CrystalTest\Form1.cs:line 27

int = Int32. No it's not the "counter" that's causing the problem. The max size of an int32 is far far larger than 32764.
I am disposing and cleaning up the datasets in the main app. That is why I didn't include them in this test; they aren't relevant.
I'm unsure why this test program is completely irrelevant. It throws the same exception, at the same count, as the main program. It does it in substantially less lines of code than our main program. I spent days running long tests to figure out exactly what I needed to make the problem appear so I could post a clean and precise post on these forums. I then created the test program to illustrate that.
The "real" code as I said does stuff in sections and in a certain order.
For each report I need to export based on rows in a table
1. Creates a new Report Document
2. Loads the report document with the report
3. Creates a dataset of the data to display
4. Calls SetDataSource
5. Calls Report.ExportToDisk
6. Disposes DataSets
7. Closes/Disposes Reports
To help isolate the problem I first took out the export to disk part (Step 5). The problem still occurred. I then took out everything related to our data. (Step 3, Step 4, Step 6). The problem still occurred. And yes I commented out this code in our main real program. This left me with:
1. Creates a new Report Document
2. Loads the report document with the report
7. Closes/Disposes Reports
At this point i had to prove it was not dependent on the report. This makes sure it's not a database connection, or pulling too much data into the report. The most efficient test for this is a blank report.
So my order of operations becomes...
1. Creates a new Report Document
2. Loads the report document with a blank report
7. Closes/Disposes Reports
So you'll see this is exactly why I wrote this test the way that I did.
I've had a run where it error on iteration 32761. My last runs have errored on 32764. I have had many runs over many weeks that all error with the same exception.
There are no temp files left behind, With a test running you can see the temp files being added but they are immediately removed.

"Attempt to copy to disk failed"

I just got a 5G 30GB Photo to replace my 4G (battery fried). When I try to sync it get so far and hangs up. I then get an error in iTunes: "Attempt to copy to disk "name of iPod" failed. The disk could not be written to or read from." Is my iPod's hard drive already fried?
HP Pavilion Windows XP Using USB 2.0 to sync

I've got he exact same problem. I too, was just removing the offending song, but since the "failed to copy" started, I'm starting to get other errors as well. It now takes iTunes no less than 10 minutes just to recognize a CD and I've seen the same "failed to copy message" regarding my hard disk. I've followed the 5 R's and the ONLY result is that iTunes dumped all 20GB of my music.
Any help that doen't require reformatting my computer or dumping data is appeciated. I'd also rather not spend another $50 on a dock. I have repaired my priviledges. I am using USB 2.0. I have already tested (and exchanged) the iPod, I have updated my OS, iTunes, and now am debating on how much more I want to put up with this.

Building exe file fails (not enough memory) in LV 2011

Hello,
I have a project with about 900 VIs. I'm using Win7 32 Bit with 4 GB RAM (a 32 Bit OS can address about 3,3 GB) with LabVIEW 2011 SP1.
When trying to build an executable, I allways get the error "Not enough memory to complete the operation" (or something like that).
My RAM is full at this time.
Without building the exe file I can start the project without any problems and with only half RAM usage.
What can I do to generate the exe file with my system?
Are there any options I can set, that the application builder will not use so much memory?
Regards
Matthias

Hello
"how much memory do those 900+VIs take on disk????"
53 MB
"Ctrl+Run Button is a force compile for a single VI"
I used Ctrl + Shift + Run
I also tried the mass compilation tool itself and it doesn't change anything.
"If the source distribution also plows the memory, you want to split the distribution into several packages"
That sounds very coimplicated ...
Did I understand it correctly? I have to create several source distributions (option "directory" and not "llb"). And in my build specification for my exe file, I can chose these source distributions?
Do I need to prepare my VIs or can I directly create the source distribution with the option "remove block diagram"?
"I had that problem several times in a large project. I did a mass compile, saved all the VIs, then closed out of the project and LabVIEW. I opened up LabVIEW again and loaded only the main VI. I performed a build and it worked successfully."
I tried it and a still get the same error.
My customer need to get the update because it a critical one. And I can't build it.
An update to Win7 64 bit on my machine is also not a solution because all our customers use Win7 32 bit and the 64 bit executable won't run on a 32 bit operating system.
Regards
Matthias

Copying files ipad3 gives 'not enough memory'

Hey folks,
Very annoying and hard to find an answer to appearently. I am copying files to apps on my new Ipad 3 and I think I've run into some kind of limit. Itunes copies a few files and then throws an error message "File bla bla bla could not be copied because an error occurred. There is not enough memory available.", and then quits syncing.
At first I thought it was a limitation of the app, but now its happening with other apps too. The ipad has 64GB and more than 10GB available.
I've read about people having the same issue with very large photo albums, but I've not seen a solution.
Thanks in advance.

On you iPad, force close all the Apps in the multitask window.
Follow these steps to force an app to close:
From the Home screen, click the Home button twice.
Tap and hold on the app.
When it starts to jiggle, tap the to close it one by one until all cleared
Now do a Soft reset of your iPad:
Hold both Home and Sleep button for around 10secs until you see the Apple logo then release. After it returns to Home screen, connect to sync and see if this resolves the issue.

Error: attempting to copy to disk failed

This is my first experience with iPod and I read the directions. I imported songs to the computer OK. The iPod came and it connected to the computer fine. The system was loading songs on the iPod just fine. After song 68 I get this error messge: "attempting to copy to the disk "name" failed. The disk couild not be read from or written to." This sounds bad. I tried the 4 step reset. I have itunes v8 on the windows XP Pro machine. And, the Nano plays the 68 songs just fine. Every time I try to synch more songs (and I even tried manual) I get the error and everything comes to a hault. Suggestions, please. Thanks.

Here is information on *+[Disk could not be read from|http://support.apple.com/kb/HT1207]+* when syncing.

HELP! Attempt to copy to disk failed.

I have tried the 5 R's, but I still can not transfer music into my iPod. I have done all the updates, resets, etc, and nothing seems to work.
iTunes recognizes my iPod and will automatically start to transfer, but will give me the "Attemt to copy disk" message. I will also, at times, receive a Device Timeout message which says "Specified I/O oerartion on Device\Harddisk2\DR4 was not completed before the timeout period expired"
No music ends up being transferred, basically, I have nothing on my iPod because of this.
Anybody have any suggestions or able to provide assistance will be greatly appreciated, thanks!
AMD Athlon 64 Windows XP

I have tried to update my Ipod numerous times and it keeps coming up with
"Attempting to copy to the disk <iPod name> failed. The disk could not be read
from or written to."
I have wiped my ipod back to factory settings. If I try to re- download itunes,
will i loose all the music I have on it including my purchased music? If so is
there any other way I could update my Ipod with all the music I have on Itunes? If there is any other way that I can update my Ipod, I would like to Know!!
Thank you
Ipod 20GB Windows XP

Message-Attempting to copy to disk failed, could not be read or written to

I"m getting this when I try to sync my iphone. What happened?

Read through this support article:
http://support.apple.com/kb/HT1207

Attempting to copy to disk failed. An unknown error occurred (-69).

I get this error every time I try to sync my ipod touch. I have restored the ipod and have attempted to download songs but after 2.3G it gives me this error.
Any ideas?

Check the song that is trying to load after you have loaded the 2.3GB, it may be corrupted:
http://docs.info.apple.com/article.html?artnum=302684

Attempting to copy to the disk "OS" failed. There is not enough memory available

I am trying to synch my ipad 2 with a dell studio windows 7 PC. The synch failed with the following error message: attempting to copy to the disk "OS" failed. There is not enough memory available. Any suggestions/ Thanks

Take a look here and see if anything in this will work for you.
http://support.apple.com/kb/ht1207

Windows 8 issue - Attempting to copy to disk "X" Failed. You do not have enough access privileges for this operation

Let me give you a quick rundown of my setup
I have a fresh copy of windows 8 64bit with a slave drive installed to handle alll my media.
Im logged in as admin and salve drive has all permissions marked as "allowed"
The error messege that occures when i go to add a new song to the itunes library (which also makes a copy in the music folder on the slave)
The Error reads as follows "Attempting to copy to disk "X" Failed. You do not have enough access privileges for this operation"
I have tried a uninstall followed by reboot and a fresh install but that made no difference...... Please help me.
_Kevin

You are showing problems with permissions on the drive. You need to either run iTunes as an administrator, or check to make sure that you are logged in with administrative priviledges on the computer. Despite having done it before, something has changed your permissions on the computer, has nothing to do with the phone.

" Attempting to copy to disk "---- ipod" failed.The disk could not be.... ?

hello every one and happy holidays.
" Attempting to copy to disk "---- ipod" failed.The disk could not be read from or written to. "
I have this problem and I can find a solution
I had try every possible tip
including.
- reset many times
- restore
- diskwarrior
- disk utility
- erase disk
- erase disk Zero out data
- erase disk 7-Pass Erase
- iPod Updater 2005-03-23
- iPod Updater 2005-09-06
- iPod Updater 2005-09-23
- MacOSXUpdateCombo10.4.3
- iTunes6.0.1 reinstall
the ipod works just fine and operates properly
it just does NOT whant to sync with itunes
I know I'm not the only one with this issue
there are many post in regard of this problem
I believe that this is a software issue and not a hardware
please comment and give any tip for me and the other people with this problem
thank you
sam
dual 800 G4 Mac OS X (10.4.3)

I had the same problem. And to think I actually HESITATED at installing the update. Oh wait... this happened AFTER the update. Funny how often that happens, eh? But I digress...
Anyway, I had two errors- initially the iPod stated my music library was somewhere else, and did I want to sync to that library. When I said yes, it reverted then to the "attempting to copy to disk"error. Further, iTunes showed that my iPod on the iTunes was EMPTY. However, my actual iPod hadn't lost any data. Confused yet? So am I.
*Last ditch effort- I went back in, and updated all my permissions, did a permission repair and then a permission verify.
* Also did a disk verify on the iPod to make sure it wasn't sick.
*I also drug a new song into my library.
*Changed from the USB plugin to the firewire. (Although I did this earlier in the day, and hadn't seen a noticeble change)
* Opened the bottle of Sauvignon Blanc. (should have done that a few hours ago)
When my first pop up asked about did I want to sync to the mystery persons library, I said yes. (At the worst, I have all my music and could reimport all 30G of it, if necessary.) And immediately, the sync began, and began appropriately. However, it IS re-syncing every single song I had on the iPod to begin with.
I suspect something nasty happened in the iTunes update, ever since the intel thing happened, the updates have been a bit sketchy. I really like Apple products, but I've gone through 3 iPods due to software meltdowns, and it's a bit frustrating.
Good luck!
iMac G4 Mac OS X (10.3.9) iPod scroll wheel,
iMac G4 Mac OS X (10.3.9) 3rd generation I think...

Attempting To Copy To Disk Failed. Not Enough Memory.

Similar Messages

Maybe you are looking for