Attempting to upgrade Switch IOS with Cisco Works 2.06

I am running RME version 4.05 and am trying to test pushing IOS images on a 3560 48port PS switch running 128mb ram and 16mb flash. When I run an analysis on Cisco works it states I only have 127mb of ram and 15 mb of flash. Is this a known bug in Cisco works. I am concerned if I upgrade with the current ram I have it will not work.

Which report are you running specifically? I have seen something like this before.

Similar Messages

  • Upgrading the IOS with bin file

    Hi Everyone,
    Need to confirm if ios has bin file only and no tar image then we can not use the archive command while using FTP to download the new ios.
    We can delete the old ios first and then upgrade the ios with copy ftp command right?
    Regards
    Mahesh

    I am asking about WS-C4503 with Supervisor II+TS.
    For chassis-based systems, all you need is copy the BIN file into the bootflash.
    Make sure you compare the MD5 hash value of the BIN file you got against the MD5 hash value found in the Cisco website.
    If it doesn't match, don't use it!
    Here's one way of checking:
    1.  Hover your curser above the filename and under the heading "MD5 Checksum" you get the value of "b6e127f2c74cfcae94e871376771e522" for the version you are going to use.
    2.  Copy the BIN file into your bootflash and run this command:  verify /md5 bootflash:cat4500-ipbasek9-mz.122-53.SG.bin b6e127f2c74cfcae94e871376771e522
    By the way, 12.2(53)SG?  You sure?  This version is classed as "Deferred" due to some bugs found.  

  • Hi . Did anyone get an error message when attempting to upgrade to iOS 7.0.2 version . I got software update failed.

    HPhasing problems upgrading to iOS 7.0.2 version

    Izatrini wrote:
    ...problems upgrading to iOS 7.0.2 version
    Then...
    Connect to iTunes on the computer you usually Sync with and “ Check for Updates “...
    See the Using iTunes Section Here...
    How to update your iPhone, iPad, or iPod touch
    Make sure you have the Latest Version of iTunes (v11) Installed on your computer
    iTunes free download from www.itunes.com/download

  • Problem with Cisco Works Assistant 1.0

    Good Morning
    I'm just installed the version LMS 3.0 on my server SunSolari 10 following all the instructions on the installation guide.
    At the end of the installation I connected the tool by Http and till now all was working fine.
    When I tried to configure the "Server Setup" by Cisco Works Assistant I got this message : " Reachable(CiscoWorks Assistant does not support the installed Common Services version.).
    Strange errors, because I have installed the LMS by Cisco DVD where the version of the applications should be the right one, infect I checked them found out that the Version of CM is 3.1 that is supported by CiscoWorks Assistant 1.0.
    Can you help me because I'm not able to find a solution
    Thanks so much in advance

    Try the solution in this thread first:
    http://forums.cisco.com/eforum/servlet/NetProf?page=netprof&forum=Network%20Infrastructure&topic=Network%20Management&topicID=.ee71a02&fromOutline=&CommCmd=MB%3Fcmd%3Ddisplay_location%26location%3D.2cbfbc4a

  • HT1414 I need help with my iPad mini. I have a white screen that continues to show a loading circle and says "Updating iCloud settings". It has been this way for several days (after attempting to upgrade to IOS 7) and I can not do anything with it. Please

    I

    As I open up Premier, it asks me for the sequence presets, which should I chose in this case? (DV 24p?, DV NTSC?, DVCPROHD?)
    Skip the step of creating a sequence, import your footage
    and create a matching sequence by doing this:
    I don't know why you don't have MPEG2 in your Encoder.
    This image is from CS5.
    Premiere Pro CS5-CS6 Reference
    (.pdf 12 MB download)
    http://helpx.adobe.com/pdf/premiere_pro_reference.pdf

  • Will an older version of the PageMaker 7 upgrade -- last used with XP -- work with Windows 7

    I haven't used PageMaker in 10 years, but now in retirement I am putting together a community newsletter with it. I get occasional errors and problems and am wondering if my version that was meant for XP will not work well with Windows 7, and whether the upgrade that is advertised on the Adobe Online site that I go to on the PageMaker help menu is an upgrade of the original upgrade and is compatible with the newer operating systems?
    Ed Pinto

    If you’re going to use old software use an old computer. Better yet, check out a new layout app.
    InDesign will be overkill for you but scribus is opensource and free. Serif Page Plus is less than $100.
    Far better than trying to get PM to work on a new machine.

  • I have ipad2. I am attempting to upgrade to iOS 5.1. Having a hard time.

    I need help to upgrade ipad2 to iOS 5.1.

    Can you give some details as to what sort of issues you are having? Just stating you have a problem doesn't make it easy to help you.

  • Upgrade 2950 ios with cna fails

    I'm trying to upgrade a 2950T from 12.1(14)EA1a to 1.12(22)EA10a.
    I dl'd c2950-i6q4l2-tar.121-22.EA10a.tar.
    In cna, went to Maintenance->Software Upgrade, selected the 2950, and pointed Upgrade Settings to the tar file.
    Click Upgrade
    It get to Reading the info file, and then
    Software upgrade failed.
    Any help appreciated.
    sean

    Actually CNA has its own embedded tftp server so you really should not have to use another tftp server. Even if space was the problem, CNA will explicitly give that error message and also provide a link to open a graphical flash management tool which will allow you to delete the unwanted files from the flash. If possible could you try that option also, I would like to know if there is any bug in CNA which forces you to use CLI and external TFTP server.

  • Cisco Works server install

    All,
    does anyone know the best practise install in respect to partitions, O/S, and what locations the log files should be placed? We recently upgraded from an old Cisco Works platform and now our full CW is broke
    So can anyone recommend any best practise scenarios?
    We have 4 x 146 gb disks that we could utilise.
    Thanks in advance,
    Tam.

    Is your environment Windows or Solaris? Did you upgrade your hardware platform only or also change from an earlier LMS version to the lastest (4.0)?
    Generally speaking, the installation guide has a good number of details. If you follow it carefully, your should have a successful installation. As with many products, when upgrading it is usually most successful to back up the data on the old system and do a clean install on the new, restoring the data after verifying a basic working system.

  • Attempted iPhone upgrade to ios4 and caput

    I attempted to upgrade to ios 4 for my iPhone 3G and now the screen displays an image of a USB plug with an arrow pointing to itunes. However, when plugged in, I get an message "We could not complete your itunes store request. An unknown error occurred (2096)" Now my phone is virtually useless. Ideas?

    Open iTunes. Turn the phone off (not in sleep mode). Push and hold the home button while connecting it to the computer with the usb cable. Release the home button when the iTunes icon appears on the phone. Then restore it.

  • Cisco Works LMS

    Can you monitor Mitel IP Tel on a Cisco router and switching environment? Customer has Mitel Voice but Cisco routers and switches. Will Cisco Works LMS provide functionality?

    See this page for a list of LMS white papers:
    http://www.cisco.com/en/US/products/sw/cscowork/ps2425/prod_white_papers_list.html
    You should fine some deployment guides for each of the various versions.  Those will help get you started.

  • IPhone 4, 16 GB. After upgrading to iOS 7, despite having 10 GB free, the phone says No storage available. Tried a soft reset, tried restore as well. Still not working. iCloud is switched off.

    My wife has an iPhone 4, 16 GB. After upgrading to iOS 7, despite having 10 GB free, the phone says No storage available. Tried a soft reset, tried restore as well. Still not working. iCloud is switched off.
    Please help.. This has become a pain.. and of course theres no way to go back to iOS 6.

    Make sure you have the Latest Version of iTunes (v11.1.5) Installed on your computer
    iTunes free download from www.itunes.com/download
    Then... Restore as New (not backup) and Re-Sync your Content.
    Restoring  >  http://support.apple.com/kb/HT1414
    SYNCING with iTunes >  http://support.apple.com/kb/HT1386

  • Cisco switch ios upgradation

    how can I upgrade cisco 2960s switch's ios.
    what commands will be used for it

    Hello Anupam, 
    1. You need to copy the IOS from CCO. 
    2. The same IOS needs to copied on to the flash. 
    #copy tftp : flash
    #tftp ip address <x.x.x.x> 
    3. I would suggest before upgrading the IOS. Please verify the MD5 checksum and confirm with CCO that it matches. This confirms that while copying the image didnt get corrupt. 
    #verify /md5 Flash:<IOSimage>.bin
    4. Once you see the IOS in flash. Please configure below. 
    boot-start-marker
    boot system flash <IOS image name>.bin
    boot-end-marker
    5. Save the confguration. 
    #wr
    6. reload the router. Post reload you can run " show version" to check if device has come up with new IOS. 
    HTH,
    Nikhil 

  • Iphone 4 since upgrade to ios 5.1.1 no longer works with made for itunes, iphone devices.

    Ever since I upgraded to IOS 5.1.1 my Iphone no longer works for playing music thorugh my Apline car unit, My Logic 3 clock radio, and a Next made for ipod device.
    I can sync through ITunes on the PC and can also play videos through the HDMI adapter.   My wifes iphone 4s and the kids  hand me down iphone 3s still play fine through these made for Itunes , Ipod , Iphone devices.
    I want to downgrade back to the prior IOS  I had before Apple encouraged me to install this bugged one.   How do I go about getting a legit non jailbroken prior IOS version installed on my Iphone?
    Is Apple aware of this issue , as I have seen blogs about this it is affecting other people?   Will this issue be resolved with ios 6?
    Can I get the beta ?
    Thanks,
    Douglas

    Agreed. Same thing here. Just bought a late model Alpine INE-S920Hd and it is all kinds of broken. I think this is happening because Apple shifted the music and video. Totally buggy. Bluetooth refuses to work properly, too. A2dp keeps stealing the audio from Pandora in the Alpine interface. The ipod controls dont work at all.

  • Hi Team, I wuold like to know if you have any app to make Firefox OS working with cisco Call Manager 10.5. Something like Cisco Jabber for Android or iOS.

    I'm interesting on buying a Firefox Smart Phone, but
    I would like to know if are any app to install on Firefox OS smart phone in order to work with cisco call manager 10.5.
    Something like Cisco Jabber for Android o iOS.
    Thanks,

    Hi Itech,
    If Cisco Jabber has a webapp, or mobile version of their website available, you should technically be able to access it through Firefox OS.
    You may also search Firefox Marketplace for an alternative solution:
    * [https://marketplace.firefox.com/]
    - Ralph

Maybe you are looking for