Attn: ANYONE with ZEN MX

)?For anyone who can convert video files into .cmv, is it possible for you to convert a few videos for me? If you are okay with that, please reply!
If not, can you help me with advice?
Video is IMPOSSIBLE.
2) I wanted to put in some movies which were in .avi format, and Creative Centrale kept saying, "Convert unsuccessful, video codec required for conversion is not installed." I have no idea what that means, but I've read what other people have done and converted my videos into .avi again using Badak.
I open the video in Creative Centrale, drag it to the "Zen" icon, and it says "transferring..." and then stops two seconds later because the conversion is STILL unsuccessful.
2) Later I managed to put in some movies once I converted it into .mov format, but a week afterward, when I wanted to add in more videos, .mov didn't work anymore. It says "Quicktime 7 or above is required," but I do have Quicktime 7. And if I try to convert it too many times, something pops up that says, "Audio Video Converter isn't responding, has been closed," and then I can't even start conversion at all. (Something about RNC doesn't work, and it shows the file as having 0 bytes)
Can someone help me figure out what's wrong?

No help available it seems - certainly not from Creative :angry:

Similar Messages

Trouble with ZEN MX

Trouble with ZEN MXWHi,
I have some issues with my zen mx,? primarily sometimes when I listen to a playlist containing many tracks or "all tracks", my player sometimes shuts of and then have to scan the disk pefore working.
Secondly there are small pauses during playback, maybe every third track or more, I'm only talking about something like a thenth of a second but it's still very annoying. This also occurs when I have many tracks in my playlist.
Thirdly I'm not able to access the recovery mode, I've tried following the instructions from the sticky-thread in the forums (Turn on player and hold in the reset butto). However when I do, the screen goes black and no recovery mode appears ever if I hold down the button for a long time.
Anyone knows how th fix theses issues?
thanks,
/Kvick

Kvick,
Please follow these steps to access the recovery mode. If this is not working for you, please feel free to contact Customer Support for further assistance.

Problem with ZEN Style M300

When I trying to found bluetooth audio devices with ZEN Style M300,? the player get to freeze after a little bit time that is searching devices, and so I have to push the reset button for using again the player. :mansurprised:Anyone have the same problem?

I have a similar problem. It recognized and paired with a Sony Ericsson MW600 Hi-Fi Bluetooth Stereo Headset once. I lost connection, could no longer connect, and tried to re-pair it. Now it recognizes the the headset's name (MW600), but when you try to pair with it stays on a "Please wait..." message. It will stay that way forever until I press the back (left) arrow. Then the message says "Remote Device not responding" and pairing fails. This MW600 headset pairs with other devices (cell phone, PC) just fine, though, so it's not malfunctioning.
I suspect this might be a Bluetooth version compatibility issue? I say that because when I connect to a Jawbone Era (pretty new device, probably latest Bluetooth spec), everything goes fine.
Also, if I clear all devices, then try to pair to just the Sony Ericsson MW600, I can get the M300 in a state where it hangs and will not respond to anything. I then have to press the reset button using a paperclip to start over.

Please help with Zen Cart

I have a running website already done in Dreamweaver and a
shopping cart with Zen cart. So far I have the two linked so buyer
can go from the website to zen shopping cart. But my issue is how
do I intigrate the two so they can flow smoothly?
For example, right now, the buyer would go to the web and
find something they would like to order, they click on the order
button, it takes them to the product page in zen shopping cart.
Since we are doing wholesale and would like to capture all traffice
plus like to give returning customers an easy way to start
ordering, we had set it up so the buyer would only see pricing and
quanity discount if they log in. Once they log in, the problem
come. It takes them to the main home zen shopping page. That means
they have to search for what they wanted to order again.
Anyone knows how to solve the problem? PLEASE HELP!!!
I hope I made myself clear.

I wrote a small store for my wife
http://www.direct2usales.com
using PayPal
Following the instructions at PayPal, each "add to cart" link
on the store consists of many lines of code which are passed to the
PayPal shopping cart... including Product Description and Price
Does your Zen cart include such a function? (with example
code you can modify for each of your store items?)

Problems with Zen Vision M Series Media Explorer using 32-bit Vista Home Prem

I'm currently experiences problems with Zen Vision M Series Media Explorer using 32-bit Vista Home Premium. When i'm trying?to burn CD's onto my Zen after?I burn the first one then click to burn another it freezes. Is there any patches i should be downloading to solve this problem??Can anyone help? Please!!!!!!!!
?Message Edited by studandydon on 07-29-20070:38 AM

I have the same problem. It all started yesterday when I was installing the cd drivers in my new computer. I have searched numerous forums and some people had to return the product. Please admins help on this issue as I understand it is very serious.

List of problems I'm having with Zen (2/4/8/16/32GB) after firmware update (12/

Anyone else having these problems? Just out of curiousity.
1. Jumpy main menu. When scrolling through, the menu will lag, and then jump.
2. Bad playback in standard WMVs. Unless the video is encoded with DivX or maybe XviD (untested), the sound is crackly and the video is a bit jumpy.
3. Song timer is skippy.
4. "Error playing song" message after changing play mode (rare)Message Edited by BetaWolf on 2-3-200706:0 PM

Worked with Zen 4GB (all firmware versions up to ZEN_PCFW_L22__20_02:
Kingston 2GB microSD with SD Adaptor
Kingston 4GB SDHC Class 6
Sandisk 4GB SDHC Extreme III

ZISD sector a moving target with ZEN 7?

I participated in a thread on ENGL's forums concernign their ActiveX
control for reading the ZISD data from within Windows using VBScript. I
asked them if it was OK to use the v1.0 of their ActiveX control with
ZEN 6.5 and ZEN 7.0 (it only listed ZEN 3.x-4.0).
Heath said they plan on releasing a ZEN 6.5/7.0 compatible version in
January 2006, which is good.
I asked him why they needed to release a new version, and he said
something along the lines of with ZEN 7, the ZISD isn't always located
at Sector 6 like it was in older versions of ZEN Imaging. Here is what
he said:
"The current release of ZisdCtrl supports ZISD @ sector 6, with ZENworks
7 ZISD may not necessarily be written at sector 6."
Does anyone have any info on this kind of thing? I am interested in
knowin gwhat some of these changes are and why they were made.
I cannot find anything on Novell's site.

The info from Heath is correct, it ZISD isn't alway's at sector 6
The reason why is because als GRUB likes to use the first few sectors on the
disk, and as such imaging had some problems with Linux Machines using GRUB.
Ron
"Jeremy Mlazovsky" <[email protected]> wrote in message
news:t%gsf.1846$[email protected]..
>I participated in a thread on ENGL's forums concernign their ActiveX
>control for reading the ZISD data from within Windows using VBScript. I
>asked them if it was OK to use the v1.0 of their ActiveX control with ZEN
>6.5 and ZEN 7.0 (it only listed ZEN 3.x-4.0).
>
> Heath said they plan on releasing a ZEN 6.5/7.0 compatible version in
> January 2006, which is good.
>
> I asked him why they needed to release a new version, and he said
> something along the lines of with ZEN 7, the ZISD isn't always located at
> Sector 6 like it was in older versions of ZEN Imaging. Here is what he
> said:
>
> "The current release of ZisdCtrl supports ZISD @ sector 6, with ZENworks 7
> ZISD may not necessarily be written at sector 6."
>
> Does anyone have any info on this kind of thing? I am interested in
> knowin gwhat some of these changes are and why they were made.
>
> I cannot find anything on Novell's site.

Itunes 10.6.3 - Just update to the new Itunes and the album artwork is not sticking anymore... I upload the artwork and when I change songs and go back the art is gone. Anyone with similar issue ?

Itunes 10.6.3 - Just update to the new Itunes and the album artwork is not sticking anymore... I upload the artwork and when I change songs and go back the art is gone. Anyone with similar issue ?

I have this issue. Album artwork was totally fine before. After this update, it is all messed up and even got messed up when transferred to my iphone.
iTunes doesn't have the artwork anymore, but then iPhone has it but shows wrong artwork with wrong albums.
Please fix!

Random Problems with Zen Micro? Try a diff. USB cable

I know people have mentioned this in other posts, but I thought I would reiterate it here. Many people seem to be complaining that their player is not recognized, or only sometimes recognized, or recognized by Windows (as a USB device) but not by their Creative software, or songs won't transfer, etc. Well, I had some similar problems which ALL went away when I started using a different USB cable - the one that shipped with the Micro just doesn't seem to work consistently.
So, if you are having problems with your player that you can't seem to solve any other way, you may want to try a different USB cable. It worked for me.
Hope this helps - I am (now) loving my new Micro!

I tried a different USB cable also, I thought that it would help, but I still got the same problems. I can almost guarantee that although you think you may have solved your issues, they WILL come back.
I've also been experiencing the "Player Not Connected" problem with my Zen Micro.
I've also had the problem where the Zen Micro just freezes in the "Docked" screen even after it has been disconnected from the PC
I've noticed that these are common problems with Zen Micros with the new firmware (.0.03)
My old Zen Micro with the old, original firmware did NOT have this connectivity problem
Creative should investigate these issues associated with this new firmware, or maybe even making the old firmware available for download to see if this really is the source of all these problems.

How to increase your battery health - anyone with similar experiences?

this is my very own self made instruction of "how to increase your battery health"
it is the procedure how i have done it serverall times on my powerbook g4 12".
my stats: 374 cycles, health 86% (3790 of 4400mAh)
age of my mac: 57month (battery bit newer)
**if you to try this: it is on your own risk!**
**this may not be suitable for mac newbies**
**be sure to read this twice before you do it once!**
you will need:
-a pocket lamp or comparable light (to see anything on your sreen when it is dark --> light from the back through apple logo)
-coconutbattery (coconut-flavour.com/coconutbattery) or comparable programm to track your battery information in realtime
-activity monitor
-cool enviroment (to ensure your fans don't have to work that much)
-some time and patience
the intructions:
step1: load your mac until the orange light turns green
step2: disconnect the power adapter
step3: use your mac until 15-25% battery life (track this information in your menu bar)
step4: slow down your activities. the order of the following actions depend on your usage of your mac:
__close programms that use lots of cpu/gpu to ensure the fans slow down to 0rpm (!!)
__turn off everything that needs battery power: airport / bluetooth / speakers / etc.
__eject dvd or cd
__close all programms with important data
__eject idisk / .dmg files in your finder (this is not only a matter of data security)
__dissonnected from peripherals such as ethernet / internet / mouse / keyboard
__use lower brightness level
__open activity monitor to ensure that your hard drive activity is very low, may be you need to close more active programms, close activity monitor when hard drive activity is very low
__open system preferences >> energy saver preferences >> choose longest battery life
when your are ready with those actions go on and ensure you are able to connect to power adapter with your mac quickly (be able to charge - don't do it yet!)
step5: be patient. now it should take some time until your battery level goes down to 3-5%
now there should be no programm running.
do not open any programm now!
do not have a look at your dashboard!
now your mac should be really quiet:
-no fans (0rpm!)
-nearly no hard drive activity!!
-->> if this not the case break go on with step 11&12, try again in a week or two
-->> if you are ready go on with step6
step6: open coconutbattery und use the lowest brightness level
play with your trackpad to ensure your screensaver won't start. waste time until you are at 1-2% battery life.
step7: take your lamp and spot through the transperent apple logo, position your coconut battery window somehow that you can see the current battery charge und the maxium battery charge in the spot of your lamp through the apple logo.
step8: go from the lowest brightness level to the level under the lowest brightness level (a dark screen)
step9: watch your current battery charge carefully und keep on playing with your trackpad to ensure your screensaver won't start.
step10: there is kind of battery buffer made of approximately 1% (once when my "current battery charge" was 3624mAh and this kind of buffer was at 36mAh)
to empty this kind of battery buffer takes much longer as you might expect!
when your current battery charge turns under this kind of battery buffer, your maximum battery charge should change. hopefully it is higher or stays the same. when it is lower now: i'm sorry - i have warned you. may be you have to go through this 'how to' more carefully!?
step11: plug in your power adapter before the battery is cero!
step12: load until the orange light turns green
step13: if it was helpful do not repeat it more than once a week, better once a month
-->webcal://www.apple.com/batteries/images/notebook_icalreminder.ics
(via: http://www.apple.com/batteries/notebooks.html)
anyone with similar experiences about increasing battery health!?
(yes, i'm sorry for my poor english, i've tried my best)

Me too! My battery lasts for 10 minutes. It is awful and I am on my 4th power adapter since they keep breaking too.
From coconut battery: Maximum battery charge 310mah, original 4400, age of mac 45 months, 140 cycles.
From system profile:
Battery Installed: Yes
First low level warning: No
Full Charge Capacity (mAh): 310
Remaining Capacity (mAh): 213
Amperage (mA): -1205
Voltage (mV): 11557
Cycle Count: 140
I went to an apple authorized retailer and they said nothing I can do if it is out of warranty.. is this true?

'Genius' related question for anyone with over 1.2TB of music?

Anyone out there with a iTunes library with over 1.2TB of music?
Reason I ask, is that I've not been able to solve a problem in updating Genuis - I'm getting the error - 'Genius results can't be updated right now. There is not enough memory available ~ Please try again later.' or the 'unknown 4002 error'. The steps I've taken to try and correct sometime back can be found in https://discussions.apple.com/message/12584815#12584815 and also shown here in sequence below.
I keep thinking this will be fixed with the next version iTunes but so far with the latest, things still the same. So looking to see if anyone with a similar size library is having similar problems and it just a limitation of the program or it's something specific on my end that I can fix.
Appreciate...
Up to this weekend I've had not issues with Genius. Worked beautifully and updated last Sunday as I have been doing every week since Apple added Genius. Yesterday I added a few albums and went to update and now getting the error of 'Genius results can't be updated right now. There is not enough memory available ~ Please try again later.' Now my library is well over >200,000 songs and only added 6 albums this time. Music sits on a external 2TB drive ~100GB free and my MacBook Pro has over 60GB open. Running latest Mac OSX and latest iTunes. Nothing new installed or changed since last Genius update.
To the points raised in this thread.
1. I've been updated weekly with a Library with over 200K songs till now with no problem. Majority is what I've ripped from my albums & CDs.
2. Deleted the albums recently added since last successful update - same result.
3. Connected directly to the network bypassing router as suggested here - same result.
4. Reinstalled iTunes program - same result.
5. Repaired permissions - same result.
Problem remains. Welcome any additional thoughts.
Question for anyone with a music library
https://discussions.apple.com/message/12584815#12584815
Ok, tried all the suggestions here yet the problem remains.
In addition what I posted above -
1) Dumped the cookies in user/library/cookies folder
2) Deleted the apple cookies found under Safari Preferences "Show Cookies"
3) Repaired disk permissions
4) Deleted iTunes Library Genius.itdb file
5) Reinstalled iTunes (with the new 10.1 version)
6) Restarted computer
7) Rebuilt iTunes Library folder http://support.apple.com/kb/ht1451
8) Deleted all iTunes dead tracks
http://dougscripts.com/itunes/scripts/ss.php?sp=removedeadsuper
9) Increased internet access speed
10) Removed all open "[" and '}' brackets from songs, albums & artists
10) Rebuilt my entire library from scratch!
Is there anyone out there with over 200K songs that can update their Genius? One thing I noted is the genuis.itdb file is just over 2GB. I'm wondering if there is a maximum size on this based on the error I'm getting. Any thought or know info on this?
Ok, think I may have found something here with this. I backed out all the music added prior to this problem occurring and ran the Genius update. All worked fine. I then started adding the music back little by little (running the update each time) until the problem returned. When the problem came back I ruled out the specific music added by backing that bit out, verified all was ok and added a different batch back in.
Bottom-line it appears that when my library exceeds exactly 1.208TB the problem appears. Interestingly enough it does not appear to be related to the number of songs, the size of the genius.itdb file (in fact when it was working the file was at 2.25GB - larger than what I reported before). It specifically seems to be related to the size of the overall library - when I have it for example at 1.2079 all is ok, 1.2081 it fails with this error.
I did try moving the library and related files to the external drive but same result. abavetta, I think your suggestion of this script may be a workaround for now - although from what I read, is this not the same that you can do anyway with iTunes by holding the alt/option key open start up? In fact I do have two libraries now - one with the 2TB drive which I use at home and another for 2x500GB disks I carry with me when i travel. I just reported the same back to Apple but doubt if any immediate solution will come for this. Too bad as one of the great things about having such a large library is the mixes you can generate via Genius. Anyway, such is life and will just live with this for now. I also just found this program called Tangerine! http://www.potionfactory.com/tangerine/ which creates playlists like Genius - although through a different technique I might also take a look at.

Just to let all know that may be having a similar problem, what I found by accident to fix this problem.
Reset all my Home Folder permissions using the resetpassword method from the startup utility in Lion. Then turned off/on to reset Genius and cleaned out the cache folder for good measure. Finally after more than a year without, have Genius up and running again.

IMPORTANT GUIDE FOR ANYONE WITH AN HP DEVICE NOT WORKING AFTER SNOW LEOPARD

To anyone with an HP printer/scanner device,
After being frustrated with my HP Photosmart C4580 not being able to scan for over an hour (scouring the forums, HP's website etc), I've come to realize my problem. Note that this has only been tested on a device that is plugged in DIRECTLY to your mac. I have not tried this over the network and do not plan to since my house is not set up for that.
Anyone who is having any issues with their device, UNINSTALL the HP software. The software is simply incompatible with SL and will mess up your devices! HP even says so on their website (see link below)!
http://h10025.www1.hp.com/ewfrf/wc/document?docname=c01846935&cc=us&lc=en&dlc=en &product=1153481
This is easily done by going to your applications folder > Hewlett Packard > HP Uninstaller. After using the uninstaller to uninstall HP's apps from your computer unplug your scanner from your computer and power supply. Now to make sure there are NO printers registered with your computer that could possibly mess up the fresh driver install, go to System Preferences > Print & Fax. Right click anywhere in the left pane (where any printers you have/had installed will be located) and click "Reset Printing System". This will wipe out any traces of a printer so you can start a-new.
Now, restart your computer. After it is restarted, plug your printer into the power source, then when it is fully booted up you may plug it into your USB slot. Then, go to System Preferences > Print & Fax. Click on the "+" (which will give you the interface to add your printer), select your printer (which you should note will say "USB Multifunction" instead of "USB" which is what showed up with the HP software still installed), and click "add". Your mac will do the rest (installing the drivers and such) and you should be able to print & scan as usual.
Note that you will need to scan using Preview, Image Capture, or your Printer Queue due to the changes with Snow Leopard (see the HP link above to learn how to use these). Your device should now properly show up when you use these applications to try and scan now.
-Mike S

@lakewood - there is nothing specifically in Software Update if you upgrade from Leopard to Snow Leopard. For me anyway..seems like thats the case for everyone though.
@ruger - so it won't even let you hit the '+'? For me, I had to hit the '+' to get it to install which in turn automatically downloaded the proper software/drivers for my device. if i were you, i'd see if i could get that to happen and hit '+' to install it. also - make sure you don't have any of the HP software on your computer also (use the uninstaller provided!)..that was really what did the trick for my machine. HP has come out and specifically said to not use the device manager, but that didn't quite do it for me. i had to uninstall everything that came on that CD (its all located in applications > Hewlett-Packard and, like i said, can be uninstalled easily using the provided uninstaller).
if all else fails, what i've also heard helps is just to reinstall snow leopard. that'll make sure everything is fresh. i'd delete all your printers like i outlined in my first post first THEN reinstalling it if you wish to go that route. however, it really does sound like the driver is messed up if its pausing and works fine with time capsule. idk how old the printer is, but sometimes with older models, the support blows. i apologize if none of this helps whatever the reason for your troubles may be, though.
Good luck,
-Mike S
PS: printers are always terrible to upgrade on everyone's end. consumers, operating systems, and manufacturers. it stinks that nothing can be generic and run similarly anymore =/

Has anyone with Windows successfully set up "Accounts" disk file sharing?

I bought an Airport Extreme basestation (the one with Wifi-N and gigabit ethernet)a few days ago and set it up on the network.
So far the wifi part has been nice - the range and speed (and stability) are a lot better than the Belkin draft-N wifi I had been using.
I've also been able to share a few FAT-32 USB disks (Iomega brand) using the "with device password" option and it seems to work nicely in this mode.
But what I really want to do is setup access by the "with a disk password" and via "accounts" - but after several hours of troubleshooting and checking on the Internet, I get the impression that neither work.
For example, when I am sharing the disks in Device mode, I can connect to the IP from windows explorer and access using any user name and the device password. This works great.
When I set it to "Disk" mode - it doesn't work at all - no matter what user name and password are used. I tried using both the disk and device password. I get a windows error "... is not accessible. You might not have permission to use this network resource..." which is consistent with the user and password authentication failure. I have the same experience when setting the disk sharing for "Account" mode.
Repeated rebooting of the Airport Extreme and Laptop did not help at all. I also tried after killing the Airport utility/assistant that sits in the task bar as it seems useless. The results are the same with the utility activated or not.
A few more details:
I have the Airport Extreme in 'bridge' mode - the IP is generated by a broadband router connected to a cable modem. I updated the firmware from the 7.2.1 that came installed to the latest (7.3.2).
I read on the Internet a number of posts from both Mac and Windows users reporting bugs in the security software on the airport for filesharing. So my question is - has anyone with a Windows (XP, vista, etc) gotten the file sharing to work with anything other than Device mode? Eg. Disk mode, Account mode, etc?
I know several people that use these devices, but nobody is using in this mode. I talked 2 friends to try setting up users and they couldn't get it to work either. But it's not a big deal to them since they don't use that feature.
If anyone is using it like this, I'd like to know how you set it up. If you had this problem and what you did to fix it. Thanks!

I suspect I may never know why, but now, inexplicably, everything is working.
Out of curiosity, I tried to connect via an older win2000 machine that we use for a file server and it worked!
After we rebooted the other XP machines, they started working too.
I'm sure the fix was anything but connecting a win2000 machine, but I'm just happy it works now!

I have a Matrox DVI docking Station, it slows my mac, anyone with the same problem

I bought a matrox DS1/DVI thunderbolt docking station.
It slowed my mac.
Anyone with the same problem?
I' m thinking on buyong the Belkin docking station, but I don't want to have the same problems as with the matrox one, any comments on this?
I apreciate your responce

Disable all Firewalls & Anti-Virus software...try again.

Problems With Zen Touch Turn

After just recently purchasing a Zen Touch in December 2005, I already have problems with it.
I have never dropped it or hit it. I plugged it in to re-charge one day after using it and when it was done charging I turned it on, used it for 5 minutes then set it down. The next morning I went to turn it on to use it, and it wouldn't turn on. The blue light at the side on the power button was on, but the screen just wouldn't show up. Now the blue light won't turn off. I have read about these problems with Zen Micro freezing up and read about Zen Touch freezing up back in 2004 when it was released. I have phoned the number but couldn't seem to get through. Should I consider taking it in? Or is there an easier way?

Have you tried resetting it's Connect to the mains adapter and press the tiny recessed button on the side of the player. Don't use anything sharp to press it, a bent paper clip is best.

Attn: ANYONE with ZEN MX

Similar Messages

Maybe you are looking for