Audigy 2 ZS and internal Firewire P

I purchased an Audigy 2 ZS and love it already, but am wondering something. The platinum version has a dri've bay panel with a firewire port that connect to the 394 plug on the Audigy 2 card.
My computer case has a Firewire port on the front of it and was thinking about hooking it up to the card. I have the following connection wires in my case:
TPA+.....matches Pin on card
TPA-......matches Pin 2 on card
Ground..matches Pin 3 on card
Ground..matches Pin 4 on card
TPB+....matches Pin 5 on card
TPB-.....matches Pin 6 on card
I also have VP and VG wires. I'm assuming these are voltage, but not sure. If so they would match with Pins 7 and 8 on the card, but I'm not sure which goes to which.
According to the card Pin 9 is not used.
I also don't have a PHY_GND wire which matches with Pin 0 on the card.
Has anyone gotten this to work with something along the same lines?
Anyone have any suggestions?
Thanks Michael

hi
i to have a problem with firewalls.in this case zonealarm.when i try to burn a cd with it on it fails.i turned it off and it finished the cd to the end.i made 2 cds that night.im using li've 24 bit.i plan to also get a router.any ideas how i can fix the firewall to work when im burning cds?tanks.
??????????coonsanders

Similar Messages

Audigy 2 ZX Platinum card - internal firewire ca

Does anyone know where I might purchase an internal firewire cable for the Audigy 2 ZX Platinum card? It is a simple 0 pin female to 0 pin female cable. But not so simple to find!?Any help would be greatly appreciated!

Hello.
I am having a similar problem:
When I first installed the card output to speakers worked fine but the Li'veDri've ins and outs did not appear in the mixer, and they of course didn't work either. Also, the remote control application didn't detect the Li'veDri've as the source of the IR.
After fiddling with the drivers (including doing the AutoUpdate), I shutdown the computer and removed the ribbon, power and firewire cables from the Li'veDri've, unseated my sound card as well as removing the IDE ribbon from it, and booted to Windows. I shutdown the computer again, and reinstalled the sound card and dri've.
The inputs were added to the mixer and Line In 2 and the Auxiliary 2 work, but the headphone out still does not work at all, and, while the Li'veDri've is detected by the remote application, the remote control still does not work. Regarding that, does anyone else's battery rattle in the remote control, especially when placed on a table?
I have checked the pins for the ribbon cable on both ends as well as making sure that the cable is firmly seated. I don't know where to go from here but to Creative's warranty services which take a minimum of 2 weeks to complete.
I also have all of the Creative Apps prevented from loading on startup, do they affect the functionality of the dri've?
Thanks for any insight,
JayMessage Edited by jayatcreative on 0-2-2005 06:46 AM

Internal Firewire P

Hello !
I'm using a SB Audigy 2 ZS. Can I enable the onboard Firewire Controller on the Card to use the internal Firewire Connecter ? I don't have the Front Panel... but I would like to use the Firewire Controller with my Case Firewire Port.

The pin positions are all the same as those on my mainboard controller. So I don't think that could be the problem. You did no change to any configuration options ? Just installed the card, plugged in the connector and it worked ?
The card uses the back Firewire port as default... so why should it use the internal controller just because I plug in a connector... that's the problem I think. But in your case it seems to recognise it.
Well... perhaps I try it again... hope it will work then.
Thanks for your answer so far... if you have any other clues... don't be shy to tell !Message Edited by tomcatoggo on 03-02-20062:05 PM

10.4.7 update and external firewire problems with HD corrupion

Dear all,
Advised by Jpfresno I started this new topic about Tiger 10.4.7 update.
I will repeat my post and what was happening 2 weeks ago:
“In 5 years 10.4.7 update was a tragedy for my Powerbook Ti 667. When I update from 10.4.6 to 10.4.7 my 300 GB firewire drive gets corrupted, after repairing it with DiskWarrior and after connecting it to my PowerBook my computer freezes and I must shut it down via powerbutton. Safari also crashes after the update.
I just erase my Hard Drive and after that install 10.4 and update with combo to 10.4.7. But I had the same problems: finder freezes with connected firewire devices and also safari when browsing. I spend a week trying to solve the problem but no luck.
Yesterday and with no firewire devices, 10.4.7 freeze and I have big trouble in order to started my powerbook!!! Even when i insert the 10.4 install DVD it did not detected my HD. Finally I get it to work and install 10.4 and combo update to 10.4.6 and everything works. My external firewire drive and safari. I already diagnose my HD with disk utility, TechTool and directories with Diskwarrior and everything is ok.
I clone my 10.4.6 to firewire, boot from it and everything is working. I let my external drive connected and finder does not freeze.
My conclusion is that the problem is 10.4.7 update. It only give me problems and I was getting crazy with it. 10.4.6 is working good and I do not advice anyone to update to 10.4.7.”
Last week after reinstalling 10.4.6 I started to have HD problems with my Powerbook 667. I did a surface scan with TechTool I it reported bad sector. Then I done a zero disk format but after a second surface scan TechTool also reported bad sector. Then I take the decision to replace my internal HD. I bought a Samsung 40GB Hard Drive and installed it on my PowerBook. Then I have done a clean installation of 10.4.6 with all applications that I need and clone it to my hard drive with Intego Personal Backup software. Everything works on 10.4.6. and external firewire drive.
After that everything is ok. But I decided to test if my problem derivates from 10.4.7 update or from previous HD corruption. Then I install 10.4.7 update on my Internal Hard Drive. Everything is working good but after connecting my external Hard Drive the finder started to freeze!!!!!!!!!. After that I tried cloning HD to external firewire with Intego personal Backup. Everything was working good but when it was finishing the backup process started to give errors!! I started panic. I interrupted the backup process but after and after restart I found something strange with 10.4.7. The system started up, I login but I could not started any application!!!??? All my application died!
Then I have done one more clean installation of tiger and 10.4.6 update.
My conclusions are that the 10.4.7 update causes all the problems that I have on my PowerBook, because I used the same methods and same software/hardware on 10.4.6 and did no have any problem.
This last two weeks were very difficult to me. I tough that these problems do not happen with Apple computers but I was wrong!!! It is very hard to me to deal with it. I always said to my friends that I never had problems with Apple computers. I accept that a hard drive died because the use of it but I can not accept that a system update cause me 2 weeks of hard problems and make me loose precious work information! I always love apple computers and Apple OS but now I am disappointed
If anyone can explain what happen or have a solution for those problems?
Thanks for the comprehension and collaboration.
Best Regards
Mac OS X (10.4.6)

Hi, alsvieira.
There are some things you did not check in all of your troubleshooting:
1. Run the Apple Hardware Test (AHT) that came the affected computer. See my "Apple Hardware Test" FAQ for comprehensive advice on using the AHT in troubleshooting.
2. re: FireWire troubleshooting: Here is some general troubleshooting advice that may help if problems return with your FireWire drive:1. Review the AppleCare Knowledge Base document "What to do if your computer won't recognize a FireWire device".
2. If this problem occurred after installing a recent Mac OS X Update, and you are also unable to mount CDs, DVDs, or disk images perform the steps in this Mac OS X Hints article. This worked under Panther and may also work in certain situations under Tiger.
3. Power-on the FireWire drive before starting up (booting) your Mac.
4. Reset PRAM and NVRAM.
5. Resett the power-management chip in your Mac.
6. Try a different FireWire port. James Wiebe, CEO of WiebeTech, has published FireWire Port Failures in Host Computers and Peripheral Devices, a white paper providing backgroud information and technical analysis concerning the causes of failure for FireWire ports. This may provide additional diagnostic information.
7. Micromat TechTool Pro version 4 can test the FireWire bus in your computer: this tests the bus — not the ports — but if the problem is on the FireWire bus on the logic board, it should reveal it.
8. Check with the manufacturer of your FireWire drive or enclosure to see if any firware updates are available for such.
9. Hopefully, the partition map on the FireWire drive is not damaged. This can happen if the FireWire drive was not Ejected before being disconnected or powered off. If it still refuses to mount, you may need to employ data recovery tools or services: see my "Data Recovery" FAQ.Note that some of the information above is from the "FireWire Problems" chapter of my book, Troubleshooting Mac® OS X.
Dr. Smoke
Author: Troubleshooting Mac® OS X
Note: The information provided in the link(s) above is freely available. However, because I own The X Lab™, a commercial Web site to which some of these links point, the Apple Discussions Terms of Use require I include the following disclosure statement with this post:
I may receive some form of compensation, financial or otherwise, from my recommendation or link.

Trying to optimize eSATA and internal disk configurations

I'm trying to optimize the HD setup on my dual 2.5GHz G5 with 4.5GB RAM
major considerations.
- massive itunes library (260GB), and big iphoto lib (25GB) as well
- lots of video editing in Final Cut with large capture files and many video exports
- regular podcasting and other media creation with all my music and photos
- need for regular COMPLETE backups
- speed
Here's the current setup. I have six disks as part of the system
1. internal 160GB disk (maps simply to a MACHD volume)
2. internal 250GB disk (maps simply to a COMMONS volume for Democracy player files, torrent downloads etc)
then on my 4-port eSATA controller card
4x 500GB SATA drives from Western Digital for a total of 2TB eSATA disk space
they are in 2 eSATA enclosures from FirmTek
I'm managing the disks with SoftRAID
Before I get into the problem, how would YOU use this incredible amount of disk space, considering the goals I have? (video, media storage, backup).
Now, The problem
I've been disappointed with the speed of my system and suspect its my HD configuration. I have enough RAM right!?
I've got some raid stripes going on
2 of the 500GB disks (disk2 and disk3) support two "active" volumes
a) a striped ATLAS volume of 800GB (holds itunes, documents, iphoto, basically all media files)
b) a striped VIDEO SCRATCH volumn of 200GB (for working files in FCP, imovie, etc)
the other 2 of the 500GB disks (disk0 and disk1) support two "clone" volumes
a) a mirror MACHDCLONE volume on both disk0 and disk1 (to protect the system drive. I run Super Duper 3x per week)
b) a striped ATLAS_CLONE volume to backup the active ATLAS volume
the COMMONS volume is not backed up in any way. figure i can live without my Democracy files and torrents, etc.
My ideas:
based on my performance observations, my setup above is just wrong, and I don't know where to turn for the best advice. Google is very poor at dealing with such complexity in search results. There are some video advice sites, but they only cover part of my problems. I have a few theories of how I should be using these drives
1. use the eSATA drives strictly for performance benefits, not for backup. consider a USB2.0 drive for backups and use Mozy for offsite backup
2. simplify the disk allocation. No single disk should support more than one volume
3. the video scratch SHOULD be striped in order to benefit from speed. and should be on its own physical disk(s) separate from ANY other function
So I'm thinking
a) stripe two of the eSATAs into a single 1 TB array for my media or ATLAS volume
- this solves me running out of space on the volume (getting closer with the iTunes video downloads every day)
- it's also just physically easier to deal with. I can SEE what drives make up ATLAS alone
- will be easier for me to eventually replace the G5 with an MBP running its own eSATA pc card with easy access to the same ATLAS volume
this still leaves two 500GB eSATA disks around
b1) I could extend the ATLAS volume to an array including a 3rd eSATA disk for a 1.5TB volume. this would allow me to bring COMMONS files onto ATLAS
b2) the remaining 500GB eSATA disk can be video scratch
OR
c1) dedicate 1 500GB disk to VIDEO SCRATCH
and
c2) partition the other 500GB disk as a clone of both COMMONS and the internal System drive
see how CONFUSING THIS IS ?
there are too many permutations of things.
I know I like keeping the system drive simple and internal. Ideally, the second internal disk would mirror this volume, but they do not match in size or brand
part of me wants to stripe all FOUR eSATA drives into a blazing 2TB masterpiece, but it seems like a bad idea to put VIDEO SCRATCH on the same array as ATLAS
Other questions:
should the itunes library get it's own disk altogether? is striping of benefit here?
are there some sites that explain HD management well?
PowerMac G5 2.5GHz 4.5GB RAM Mac OS X (10.4.9) also own a blacbook

Thanks so much for that awesome feedback.
A few points.
I have the dual processor G5, not the quad core. Purchased in Jan 2005.
My RAM pageouts are fine (didn't know what that was until you mentioned it)
Love the idea of moving COMMONS "outside the box"
I used to have my system volume boot from an external RAID, but didn't notice a big improvement, and it meant my G5 would ONLY boot if the eSATAs were powered up. I just didn't like that feel. I want the tower to work in a self-contained fashion, even if I don't have access to all media. I want access to the OS and apps.
I'm unlikely to buy more SATA controllers and enclosers or too many new disks. I'm on a serious budget and want to work with as much of what I have as possible. That said, i just checked out the Drobo and am drooling. I'll wait to see how well it performs for data access (and video) and not just storage.
It sounds dreamy to stripe all four of the eSATAs into a 1.8TB storage megaplex. I imagine they would scream in an ATLAS_BADASS volume, but then I've got nothing left for VIDEO SCRATCH used to capture and render.
The VIDEO_SCRATCH doesn't need to be large, and I think that's where I'm having a conflict. My eSATA drives are way too big to use even ONE as a video scratch, much less striping two of those bad boys just for that purpose
Purchasing a 10K drive for video scratch (or system volume) is not really in the cards yet.
So here's where I sit now:
1. My Media Storage
++ the 4 eSATA drives (2.0TB raw)
I go with the badass steroid injected ATLAS volume striped across all four.
this is my media array and holds all the contents of ATLAS and COMMONS (iTunes, iPhoto, Documents, FCP training videos, ripped DVDs, the works)
2. My System Volume
++ the 250GB internal SATA
move COMMONS out
migrate system volume to this disk
better storage-to-free space ratio
3. My Scratch Disk
a) use the now-spare 160GB internal Maxtor (probably weak and slow)
b) get an external FW800 RAID disk from OWC
http://eshop.macsales.com/shop/firewire/hard-drives/EliteAL/StripedRAID
I'd go with the 160GB or 320GB
4. Backup Plan - level 1 - local
++ use my spare external Maxtor 250GB FW drive
clone the system volume regularly
++ get an external FW drive (like the 1TB My Book Premium II from WD)
clone ATLAS_BADASS regularly
the WD is just $400
i know it's capacity is lower than my super striped RAID, but i don't know of any cheap way to clone ATLAS_BADASS to a 1.5TB drive
5. Backup Plan - level 2 - remote
pay for a Mozy storage account which has unlimited capacity
upload system and ATLAS_BADASS every few weeks
any new thoughts? and thanks again!

Audigy 2 ZS and Xbox

I realise that questions have been asked before but I couldn't find the correct information.
I have an Audigy 2 ZS on its own, just the card no dri've bays or anything like that. I have connected the optical audio cable from my xbox to the digital in but I get no sound on any of the settings selected from the xbox. In the audio console all i get is "unknown or invalid signal"
Is it actually possible for my card to decode the signal from my xbox? If not what do I need to buy / install to make it work.
Thank you!
Rich

kenai36,
I'm a little confused about what you are trying to do. Are you trying to connect to the spdif jack on the Audigy 2 ZS circuit board? Otherwise, the backpanel of the Audigy 2 ZS has a digital-out and a firewire jack. Neither of these handle optical I/O. You could add a Platinum dri've which has an optical spdif connection.

Simultaneously downloading with the 400 and 800 FireWire on the Mac Pro

During a Mac Pro training Web Cast the speaker related that one could download with both the 400 and 800 FireWire simultaneously, however the speaker never explained how to do that.
How would you go about downloading simultaneously?

The external hard drives have their own power.....turns out that the 400 and 800 firewire busses are the same.....What Apple did was an 800 firewire buss and has 1 port located on the rear of the tower and 2 400 ports (one one the front and one on the back). The 2 400 ports are equal to the 1 800 port, so when you use one 400 port and 1 800 port the 800 port becomes another 400 port. In other words.....I only have 1, 800 buss and not an 800 buss and 2 400 busses....pretty tacky if you ask me......also, I learned that the Canon DV cameras (ZR70MC) is a real hog when it comes to firewire, so, when I have my external hard drives plugged into the 800 buss and the Canon plugged into the 400 buss, it's on overload and their is no buss protocal for who uses what. Which means if the external drives are using the buss the Canon is out of luck......The solution is to install a separate firewire card and plug either the Canon or the drives into it thus freeing up the internal 800 buss for other uses.
The workaround is for me to unplug the power to the external hard drives, plug in the Canon, capture all of my material onto the internal drive, once I've captured all of my files, remove the Canon from the buss, powerup and re-mount the external drives, then, move all of my captured files over to my work space which is located on one of the external drives......what a pain in the butt......but that's the way it works.....

Soundblaster Audigy 2 ZS SC w/FireWire Multimedia Au

I just reformatted my XPS Gen 5 and apparently the Audio Driver I need for the aforementioned card is no longer supplied by Dell.
This specific Audio driver isn't listed for download by Dell and isn't available for download on CreativeLabs anymore. Here's the details:
SP 0358
Dell said for me to contact CreativeLabs since they no longer have the driver.
Where can I get it's
Thank you.

Maggard wrote:
I just reformatted my XPS Gen 5 and apparently the Audio Driver I need for the aforementioned card is no longer supplied by Dell.
This specific Audio driver isn't listed for download by Dell and isn't available for download on CreativeLabs anymore. Here's the details:
Soundblaster Audigy 2 ZS SC w/FireWire Multimedia Audio
SP 0358
Dell said for me to contact CreativeLabs since they no longer have the driver.
Where can I get it's
Thank you.
As it's an OEM product you have there, you probably need to modify the installer meant for original CT products. I have posted some instructions long ago so if you search here by using "ctcomp.exe" as a searching criteria you might find that thread. You also need drivers from older installer since CT made some changes to the installer so that the old ctcomp won't work with the latest driver installation. IIRC, there were a fix-up for this too available but I'm not sure where it was introduced ... was it @ DHF (link given below)?
You can download the CD as an ISO image from BadBoys site (http://badboy.filefront.com/).
IIRC, there were some other instructions for this @ Driver Heaven Forums and also you might already heard of YouPAX driver mod ... which can be found @ Driver Heaven too.
jutapa

MAC G5 2004 are the 400 and 800 firewire busses interconnected?

When I plug in a DV camera to the 400 firewire buss and go to system profile/firewire, the DV camera doesn't show up.....but, when I turn the firewire hard drives off (pull their power) thus disconnecting them from the 800 firewire buss, the DV camera shows up....
If I have my firewire external drives connected to the 800 firewire port, and the DV camera connected to the 400 firewire port sometimes (not often) the the dv camera works, most of the time it doesn't..... help!
The only way I can get the dv camera to work is to disconnect the firewire hard drives from the computer then all is good in the land of "MAC).....

The external hard drives have their own power.....turns out that the 400 and 800 firewire busses are the same.....What Apple did was an 800 firewire buss and has 1 port located on the rear of the tower and 2 400 ports (one one the front and one on the back). The 2 400 ports are equal to the 1 800 port, so when you use one 400 port and 1 800 port the 800 port becomes another 400 port. In other words.....I only have 1, 800 buss and not an 800 buss and 2 400 busses....pretty tacky if you ask me......also, I learned that the Canon DV cameras (ZR70MC) is a real hog when it comes to firewire, so, when I have my external hard drives plugged into the 800 buss and the Canon plugged into the 400 buss, it's on overload and their is no buss protocal for who uses what. Which means if the external drives are using the buss the Canon is out of luck......The solution is to install a separate firewire card and plug either the Canon or the drives into it thus freeing up the internal 800 buss for other uses.
The workaround is for me to unplug the power to the external hard drives, plug in the Canon, capture all of my material onto the internal drive, once I've captured all of my files, remove the Canon from the buss, powerup and re-mount the external drives, then, move all of my captured files over to my work space which is located on one of the external drives......what a pain in the butt......but that's the way it works.....

Anyone using Login Pro and PowerCore Firewire

I have a G5 dual 2 gig with 4 gigs or RAM, 2 x 160 LaCie HD, RME Firewire 800 and PowerCore Firewire. I have been having issues with PowerCore losing connection, plug-ins load and are disabled, and total system lockups.
For testing, I removed all audio IO drives and used internal audio, remove all midi drives and I am still having the same issues. Anyone using Login Pro and ProwerCore Firewire successfully?

I am on the same machine as you. Most of my problems (similar to what you report) have been due to the driver/software of the Powercore. Luckily for you, TC doesn't have phone support, so you can be spared the immediate relief you don't want and wait the 48 hours for a general email response that says you get to wait another 48 hours until someone gets back to you.
That said, Powercore FW works fine for me. It sounds like you are using a lot of FW devices, which might also contribute to your problem. I've found that you can actually overtax the FW ports on G5's to the point where they stop working properly, causing random connection loss.
Does the powercore connect through any other device?
Trying unplugging your LaCie's and see if that helps.

MSI K8T Neo-FIS2R Trying to add card for internal firewire header

Tiresmoke and anyone else who can help.
Maybe you remember me I have the above board and couldnt get it to recognize my Sata drive. Well I got an RMI and sent it in for repairs. Apparently there was something wrong with it because it works like a champ now.
Now I have a new problem with it.
My new case has a front firewire plug that is wired with an internal header type plug. This MB doesnt have a header for it. I also need any extra USB internal header for my floppy card reader, the 2 that are on the MB are being used by the "D" bracket and my front USB jacks, so I bought a card from New Egg that had both. The card is a "PCI Multimedia combo card" #15-107-112 from Link-Depot.com. I cant get this card installed. Instructions say it should find the drivers on my XP Pro disk with service pack 2. When I boot windows finds new hardware but cannot find the proper drivers. IVe tried leading it to the XP disk but know luck.
The manual says I need to install three types of drivers before the combo card will function properly.
1. 1394 Bus Controller driver
2. ALiPCI to USB Open Host Controller driver
3. ALiPCI to USB Enhanced Host Controller driver
It says the card is compliant to IEEE 1394 Open HCI specs.
Before the card was installed Device Mgr. said there was a VIA OHCI Compliant IEEE 11394 Host controller installed(There were no Yellow or red symbols on it)
Under Universal Serial Bus Controllers there are several lines:
Standard Enhanced PCI to USB Host Controller
6 USB Root Hubs
4 VIA revision 5 or later USB Universal Host Controllers
VIA USB Enhanced Controller
So now I wondering if somehow these devices from the Motherboard are causing confusion with installing the card.
Can anyone help me out here?
Thanks !!

Thanx for the reply. I figured I could drop the D bracket but that still doesnt get me the internal firewire header. This card has a std firewire jack like on the back ot the computer so I had to buy a converter cable to go from the header pin plug to the std firewire plug. Heres the link to the card I bought.
http://link-depot.com/PCI-COMBO.html
Why cant I get this card to install is still my problem.

Excise Invoice number and Internal Number

Hello Friends
I have some queries ,I will be thankful to you if you could guide me, in understanding themu2026
1) When we see the document in J1IEX ,in excise invoice tab, we see two fields :Excise invoice number and Internal Number.
For Internal number we define the range in object J_1INTNUM, but how do we define range for Excise invoice number
2) Where do we maintain the relation between GRPO (Excise Transaction type) with the Excise Invoice number
3) When do we require updating of register ,is it done on daily bases, and how can we see the entries of RG23A part 1.
4) We have excise invoice number range of posted ,in process and cancel documents which is assigned to GRPO transaction type, while running J1I7 though we select last option part 1 posted and part 2 not posted, still the system shows the cancelled documents, How can I avoid the cancel documents
Thanks
Siddharth

1) When we see the document in J1IEX ,in excise invoice tab, we see two fields :Excise invoice number and Internal Number.
For Internal number we define the range in object J_1INTNUM, but how do we define range for Excise invoice number
-->> Ex inv nbr will be entered based on the vendor ex invoice .. this is external nbr assignment
2) Where do we maintain the relation between GRPO (Excise Transaction type) with the Excise Invoice number
--->> there is no relation between grpo vs. ex inv nbr
3) When do we require updating of register ,is it done on daily bases, and how can we see the entries of RG23A part 1.
>> u can see in J1I7 or thru table J_1IPART1
4) We have excise invoice number range of posted ,in process and cancel documents which is assigned to GRPO transaction type, while running J1I7 though we select last option part 1 posted and part 2 not posted, still the system shows the cancelled documents, How can I avoid the cancel documents
>> wait for others answers..

What is the diffrence between External postings and Internal postings in CO

Dear all,
Can brief me anyone about the Externa postings and Internal postings in CO,
I suspected all postings from outside or interface postings is External postings and all FI postings is internal postings, Is it true or not still i am suspecting, anyone pls clarify the doubt.
Thanks
Raghu
Moderator: This forum is not dedicated for basic questions. Please, read SAP material before posting

Hi,
All postings which are originated from other than CO module ( i.e from interface, FI etc ), are called External postings in CO.
Whereas internal postings means posting which happen within CO module, example Assessment, Distribution etc within a company code.
Njoy
Siva

External and internal mikes are not automatically switching over either recording or on voice calls

My laptop model name is HP Pavilion dv4-1100ea which is shipped with Vista Home premium 32 bits and has got service pack 1.
Restored the laptop to factory setting since then I am having the following problems; I had the same problem when my laptop was brand new and whenever I reset the laptop to factory setting I get the following problems:
1. External and internal mikes are not automatically switching over either in middle of the recording using sound recorder or while the call in progress on voice calls (skype):
   Using the sound recorder if I start recording the sound with external mike and in-between recording if I switchover from external mike to inbuilt mike and later on when I play back I can only hear the sound up till where I used the external mike during recording, after the switchover to inbuilt mike I cant hear any sound.
   But if I start the recording with inbuilt mike and in between recording if I plug in the external mike and later on when I play back I can only hear the sound up till where I used the inbuilt mike during recording , after the switchover to external mike I cant hear any sound.
   So in brief both my external and internal mikes are working fine, only problem is that if I start recording (using sound recorder) or voice call with one specific mike, I have to continue with it till the end. I can’t switchover to another mike in between the conversation (voice call) or recording, if I do so, I have to select the mike manually in chat software but while recording I cant even select manually because in laptop, it takes the mike whichever is in current use as default mike in recording tab(sound window). The green tick automatically (in recording device tab) switches over according to the use of mike. Though the green tick in the recording tab is switching over automatically according to use of mikes, its not picking up the sound after switch over during recording.
2. And also when I click on recording device tab in sound window and plug in external mike, though the green tick automatically switchovers from internal to external mike, while I speak both internal and external mikes volume meter respond to the sound inputs by rising and falling but if I take out external mike, green tick goes to internal mike and when I speak only internal mike volume meter respond to sound rising up and down not the external mike.
To resolve the issue I have tried following steps with no luck:
1.I have checked the mikes(internal and external) properties, the both mike shows to be enabled in general tab, in level tab the volume is set to 100 and in advanced tab , all options are selected.
2. In device manager I have got only one audio driver named as “IDT High definition Audio CODEC”. I have uninstalled the audio driver and reinstalled it using scan for hardware option
3. Uninstalled the audio driver in device manager and reinstalled the audio driver using recovery manager > advanced option> hardware driver re-installation.
3. I have updated the BIOS(Insyde F.65, 12/02/2010).
4. I tried to update the audio driver using below link but things went more worse so I did system restore (not factory setting though).
http://h10025.www1.hp.com/ewfrf/wc/softwareDownloadIndex?softwareitem=ob-67051-1&lc=en&dlc=en&cc=us&...

Sounds like you need to upgrade to the iPhone 5s
The 5s has Touch ID
You can unlock your phone with your finger instead of typing in a key code
No swiping to unlock either, just touch the home button
You can enrol multiple fingers as well
Here is a video of it in action
http://www.apple.com/iphone-5s/videos/#video-touch
Or wait and see what iPhone 6 has to offer
That being said, as desiel vdub posted if the phone is up to your face, the proximity sensor should turn the screen off
And when you lower the phone turn it back on again
Not sure about the phone locking when your on a call doesn't sound right

PO and internal order

Hello i have a question concerning PO and Internal Orders.
I have created some Internal Orders and i have made a PO for assets with this internal order (internalorder1)
Now i have authorised a user with another internal order number.(internalorder2)
Can i somehow prevent a user to release POs for internal orders according to the authorised internal order.(internalorder2)
Maybe the authorization object k_order the field co_action???

If you use TCode SU24 to look at the authorization object checking for the object K_ORDER you will see that this object is not checked for TCodes ME21, ME21N, ME22, ME22N, ME23, or ME23N. This is probably why you can still use any internal order whether you have it in your profile or not. You might be able to add the authorization object to these to the MM_E Materials Management: Purchasing class. I think you can use TCode SU21 to maintain these objects, but you need to check with your Basis/Security personnel.
As a test you can use SU24 to look at object M_BEST_EKO Purchasing Organization in Purchase Order. You will find that it is checked in pretty much every PO creation or change TCode (ME21, ME21N, ME22, ME22N, ME23, ME23N, ME24, ME25, ME26, ME27, ME28, ME29N).
Regards
Edited by: Paul Shrewsbury on May 11, 2009 2:32 PM

Audigy 2 ZS and internal Firewire P

Similar Messages

Maybe you are looking for