Audigy 2 ZS and using PC Case por

Every PC case I see has Audio ports along with the usb ports. But how can I get my Audigy 2 ZS to work with them? Is there anyway it could be done? I am talking about the mic and head phone ports.

Seems like Creative should have this kind of information available in a spec sheet somewhere.
Not really. Only reason those connectors are there in the first place is because of Dell.
Anyway,
?http://audigy2zshowto.blogspot.com/
or if you don't want to make your own,
http://www.x-tap.com/
Have also seen the cables on ebay occasionally.
Message Edited by stormy3 on 05-28-2008 0:06 PM

Similar Messages

Audigy 2 ZS and normal front case/panel ac97 connecti

Hello,
I've always been curious if the Audigy 2 ZS (model SB0350) which I have has the capability of using standard case connections for front case connectors such as audio/mic inputs/outputs. For example, most standard cases have plugs in the front for a headset/mic, and the cables for these usually plug into the motherboard using the onboard soundcard.
I've noticed on the Audigy 2 ZS card that I have that is has many alternate connections for things such as the creative front panel, firewire, joystick ad many other alternate cd/aux inputs.
There is also a white connector which has the reference "J" on the top left hand corner of the card containing a total of 0 pins. Apparantly this is just a standard analogue audio input/output which is exactly what I was looking for. People have had success using this connector to do the job that I was always curious about.
My question is, is there a connector/cable available from Creative to plug into this socket. I've looked all over the net and had no luck finding one. Why would it be placed on the card if it was never planned to be used for anything? Some people have come up with a pinout for it and what each pin does.. anonymously but where did they get this information from?
Any help would be appreciated on the availability of a cable for this socket, what was its intended use etc. Hopefully someone clear up this question mark in my head
Regards,
Mark

Seems like Creative should have this kind of information available in a spec sheet somewhere.
Not really. Only reason those connectors are there in the first place is because of Dell.
Anyway,
?http://audigy2zshowto.blogspot.com/
or if you don't want to make your own,
http://www.x-tap.com/
Have also seen the cables on ebay occasionally.
Message Edited by stormy3 on 05-28-2008 0:06 PM

When to use the Adapters and in which case

Hi Experts,
I am little worried and searched the sdn, but i am not getting the proper answer for my question.
My Question is when to use which adapter and at what stage?
1. File --> when to use it and in which case
2. IDOC
3. RFC
4. SOAP
5. XI
6. HTTP
And also where to use BPM and Proxies, when should we go for them.
Please help me out. I Beg the answer from experts.
Regards,
Raj

Hi,
If an incoming or outgoing message is a file(.txt,.csv etc), we use a file adapter
If the outgoing message is an IDOC, we need an IDOC adapter.same for RFC also.
SOAP for incoming/outgoing webservices
XI while using proxy scenarios
HTTP- while you an HTTP request.
BPM and Proxies is a vast topic.
For Proxies http://help.sap.com/saphelp_nw04/helpdata/en/5d/112d20f6ce6c46ba66afb98d278fbd/frameset.htm
and for BPM http://help.sap.com/saphelp_nw04/helpdata/en/5d/112d20f6ce6c46ba66afb98d278fbd/frameset.htm
this will be useful.
Regards,
Tiny

Can we assign 2 IPs for a SCCM 2012 primary site server and use 1 IP for communicating with its 2 DPs and 2nd one for communicating with its upper hierarchy CAS which is in a different .Domain

Hi,
Can we assign 2 IPs for a SCCM 2012 primary site server and use 1 Ip for communicating with its 2 DPs and 2nd one for communicating with its upper hierarchy CAS . ?
Scenario: We are building 1 SCCM 2012 primary site and 2 DPs in one domain . In future this will attach to a CAS server which is in different domain. Can we assign 2 IPs in Primary site server , one IP will use to communicate with its 2 DPs and second
IP for communicating with the CAS server which is in a different domain.?
Details:
1)Server : Windows 2012 R2 Std , VM environment .2) SCCM : SCCM 2012 R2 .3)SQL: SQL 2012 Std
Thanks
Rajesh Vasudevan

First, it's not possible. You cannot attach a primary site to an existing CAS.
Primary sites in 2012 are *not* the same as primary sites in 2007 and a CAS is 2012 is completely different from a central primary site in 2007.
CASes cannot manage clients. Also, primary sites are *not* used for delegation in 2012. As Torsten points out, multiple primary sites are used for scale-out (in terms of client count) only. Placing primary sites for different organizational units provides
no functional differences but does add complexity, latency, and additional failure points.
Thus, as the others have pointed out, your premise for doing this is completely incorrect. What are your actual business goals?
As for the IP Addressing, that depends upon your networking infrastructure. There is no way to configure ConfigMgr to use different interfaces for different types of traffic. You could potentially manipulate the routing tables in Windows but that's asking
for trouble IMO.
Jason | http://blog.configmgrftw.com | @jasonsandys

If I buy a lifeproof nuud case for my iphone 5 can I also buy a screen protector such as an amzer and use it aswell I have had a lot of screens break from little falls out of my pocket

If I buy a lifeproof nuud case for my iphone 5 can I also buy a screen protector such as an amzer and use it aswell I have had a lot of screens break from little falls out of my pocket

The Lifeproof case will provide reasonable protection from accidents and liquid intrusion. Screen protectors themselves provide essentially no protection, other than from minor scratches.
You can use the ones Lifeproof included, or less expensive ones. The cheapest ones you can find on the market are adequate. More expensive ones don't do anything better. Some can damage the glass, which won't be covered under AppleCare.
It's practically impossible to apply any of them without trapping a piece of dust.
None are really required.

Address and Use Case

Hi expert,
Normally when we creating a permanent address (time cons 1), the old record delimited and new record will start to 31.12.9999, this is the desire result. How ever when using ess, and using edit (or new), the old record get deleted and new record with today start date is inserted. I have tried all possible use case but still it doen't mimic the back end. What i want is permanent address can not be deleted, can only be edited from today and the old record delimited as today (so we still can see the old one just in case the employee try to do something funny). Can some one help me with this, we are using ecc6.0 and NW 7.0 with no EHP? Thanks

Hello Salim,
You should maintain the usecase A1 for permanent address and the Time constraint should be 1.
There should be no problem after that. The record should be delimited then.
Best Regards,
Deepak..

Audigy 2 ZS and inspire T7700 no 7.1 with mov

Hello. Maybe you can help me:
I was trying to watch Episode one (with Dolby sourround EX) with power DVD 6 an Windvd 6 plat but i'm having problems with my 8 channel output because when i start the THX optimizer, the sound that is supoused to be heard on my side speakers, comes from the rear speakers and the sound from channels 6 & 7 (Rear center) its also coming from those speakers. This Failure also happens with the Windvd Channel test: side speakers doesn't work and in power DVD 6, CLMEI II technology does not work with side speakers. The only way to get sound from my side speakers is with CMMS.
The tests for the THX console for audigy 2 complete succesfully altough it keeps me saying that my side speaker and sub aren't wired correctly (polarization test). The channel and noise testing goes ok besides that.
This problem is exclusi've to DVD watching beacause with EAX HD 3.0 or 4.0 games, i'm not having any problem.
is Dolby digital EX in episode really works with 7. configurations (region 4)?
How do i need to configure this players to work with the installed decoders?
Are my speaker set defecti've?
Can i buy some kind of monster cable to imrpove my sound?
It's that all right that the sound from 5. tracks (DD or DTS) is played from the front and rear speaker and not in the side ones?
Note:
The supoused wiring problems repeats itself even if i change the connector of the the side speakers with the rear ones (that are soppoused to work fine). That means (i think) this problem isn't caused by the speakers wiring (i think i made it ok) could it be that the 7. cable is deffecti've?
What to do? Please Help me
Creative Staff: where i can go to check this on Mexico city? is there any sopport center where i can go and get some help?
My config:
Audigy 2 ZS and Creative inspire 7. T7700

My guess is that your PowerDVD and WinDVD versions don't have ES support and you're using the programs to decode. This might be the case if you are configuring the programs for multiple speakers. If you are, try configuring them for SPDIF output, then make sure the soundcard is configured to decode AC3/DTS (it probably is). Does that help?
-Dave
[email protected]

Sound Blaster Audigy 2 ZS and Logitech 5.1 Surround So

Hello everyone, this is my first post on these forums, so I thought I'd just start out by saying hello.
I also have a bit of a problem. For the past several months I've had a Sound Blaster Audigy 2 ZS and a set of Logitech X-530 5. Surround Sound speakers hooked up to my computer. For a these past few months, only two of my speakers have been functionable.
I know they're not broken, because I can plug in separate cables into a certain plug and either my two front speakers will work, my two rear speakers will work, or my center speaker will work. And yes I do have the most recent drivers for my card. :P
If anyone would be able to help me with this problem, I would really appreciate it. Thanks!
By the way, here's a picture of the X-530 Speakers I'm using, just in case anybody needs to see them for reference:
http://img53.imageshack.us/img53/2758/b0002wpscg0ss500sclzzzsr.jpgMessage Edited by Triko on 02-26-200706:20 PM

Turn on CMSS if you have not done so.
Jason

Audigy 2 ZS and Windows 7 RTM drivers

Hey
I was wondering about Audigy 2 ZS drivers for Windows 7 RTM. Any information on them? I want to get the card fully (or as close to fully) working on Windows 7 but the most important part is that it supports (my)?7. speakers.

Creative's latest should do fine (v2.8.00), but be aware that there's a problem with playing MP3s in Windows Media Player while in 5. mode (prolly applies to 7. mode aswell) - I can only confirm this is the case in the Win7 R though, may work fine in other versions of Windows.
Or use Dan K's, but with his, despite re-enabling CMSS2 and Stereo Surround for the various speaker configs, his packs screws up CMSS/CMSS2 when in headphones mode (which personally is the only time I use CMSS - love me some virtualized 5.).
I'd go with Creatives if you game and use headphones mode much.

Audigy 2 ZS and ASIO 24/96

I have seen several posts about how to use ASIO 24/96 driver for Audigy 2 ZS but they are pretty old now and the problem I have experienced is just a few years old.
I used the driver on my old XP 32 bit computer for critical recordings for highest possible quality though it was only possible in Wavelab for single track recording/playback. Running multitrack was too heavy for my computer. I then had a long break from music making and started again a year ago. I couldn?t get that driver work again but didn?t bother much as I didn?t have to record any external audio yet.
Last weekend I upgraded my computer to a quadcore cpu with 6 gig RAM and Windows 7 Pro 64 bit. I can now use ASIO 24/96 and it runs smooth and free from glitches - but it only works for playback. Whatever input I choose all I get is silence. The other two ASIO drivers works though but they cannot record in 24 bit/96 kHz. In worst case I could have used the WDM drivers only for the recording part but those does not work at all at any rate - I get so much dropouts that the recordings are full of "holes".
Has the drivers been changed during the years so actually can't record when using ASIO 24/96 driver? If it wasn?t for the fact that it didn?t work on my XP?system either I would have thought it was a Windows 7 issue.

Gorilla wrote:
For some reason I have an error message in ADIC Pro 5.
I have an Audigy Platimum Pro and I changed the audio devie type in the Preferences to SB Audigy 2 ZS ASIO 24/96 (FF40), but when I try to record and check the little monitor bar, I can see the levels, but I hear no sound. If I uncheck it, I see no levels, but I hear sound. I cannot record because of this sicne when I hear the sound nothing is getting recorder. I doublechecket everything but I cannot solve the problem. Please help me if you can
Thanks
Peter
Hmmm.. What the error message says?
Which input source you have selected to record from?
Have you selected the output port(s)?
Are project samplerate and bit-depth set to 24/96?
Does this issue occur when ASIO res is set to 16-bit/48 kHZ?
Is tehere a setting for monitoring on ACID audio/global properties (other than the ON/OFF found on every track)?
jutapa

Audigy 2 zs and logitec z

Hi there,
I can't seem to figure out which digital cable to use to connect audigy 2 zs and my speaker system (logitec z680). the speaker system has a option of digital coaxial and optical output but the sound card doesn't have coaxial or optical ports (why wouldn't this sound card have coaxial port when most entertainment media has it's?).
My speakers work (for most part) with analog cables, but i want to enjoy the actual digital experience thats meant to be with these speakers and this card but it appears that i can't. Can you plz tell me what to do because with analog cables, either my center speaker doesn't work or if that works, other speakers don't work. Can you tell me which digital cable should i use? because for some reason, not many people know which digital cable you have mentioned in ur user manual.
I am really fed up because i just spent over $500 in total and i can't enjoy all the quality of this speaker system and the soundcard that makes up the price.
thank you

Hi there
If you are looking to use the coax then you need the converter (mini plug to female RCA). I'd be amazed if Creative couldn't sell you one. I got one as part of my GD580 pack. I think it is a special mini-plug though specific for this job.
Word of warning on the coax digital if you do hook it up - no good for gaming. You need the analogues for the best gaming sound (EAX doesn't come through digital SPDIF - only stereo through the SPDIF believe it or not). The coax digital should do you for DVDs and similar DD5./AC3 encoded material but only if you set the SPDIF to passthrough and allow an external decoder to take care of converting to the 6 discrete signals.
The question is therefore which has the best decoder - the Audigy or the z680? I don't know the answer to that but knowing the agony I've just been through with my GD580, I'd recommend sticking with the analogues. I'm upgrading my system to do exactly that. If you were going to a decent Home Theatre decoder/amp with the digital signal then that may be one case where the digi out from the card would be of use.
Hope that hel
ps.

Audigy 2 ZS and internal Firewire P

I purchased an Audigy 2 ZS and love it already, but am wondering something. The platinum version has a dri've bay panel with a firewire port that connect to the 394 plug on the Audigy 2 card.
My computer case has a Firewire port on the front of it and was thinking about hooking it up to the card. I have the following connection wires in my case:
TPA+.....matches Pin on card
TPA-......matches Pin 2 on card
Ground..matches Pin 3 on card
Ground..matches Pin 4 on card
TPB+....matches Pin 5 on card
TPB-.....matches Pin 6 on card
I also have VP and VG wires. I'm assuming these are voltage, but not sure. If so they would match with Pins 7 and 8 on the card, but I'm not sure which goes to which.
According to the card Pin 9 is not used.
I also don't have a PHY_GND wire which matches with Pin 0 on the card.
Has anyone gotten this to work with something along the same lines?
Anyone have any suggestions?
Thanks Michael

hi
i to have a problem with firewalls.in this case zonealarm.when i try to burn a cd with it on it fails.i turned it off and it finished the cd to the end.i made 2 cds that night.im using li've 24 bit.i plan to also get a router.any ideas how i can fix the firewall to work when im burning cds?tanks.
??????????coonsanders

Get cell value in Planning Data form and using it in a business rule

Hi Everybody,
if i set the data type of an Account Member as text, is there a way to get the value inserted by the user in a dataform, turning it as dimensional member and using it in a business rule?
So, if the user insert the value "USA" in a cell, can i use any functions to tell essbase that "USA" is a dimensional member and then using it in a business rule, for example in a cross-dimension like Period1->FY12->USA?
I tried to use the function @Member and it doesn't work, but i'm wondering if there is a way that can let me get the value inserted and use it just like a dimensional member. What are the ways that can let user input value that can be used in a business rule? I think one is by using SmartList, is there any other ways? Maybe using variables?? As an alternative i tried to use Prompt Variable but there are too many members on which the rule must run.
Please help me, i wanna know if i can or not let the user input the member on which the rule must run...
Thank all guys
Bye
Maurizio

Thanks EW for your answer,
YesI could use SmartList even if i think it's very tough to handle. My experience on using SmartList in caclc script is not so good. I try to enter in details of my requirement:
I have 500 account members.
For each one, I have to calculate the monthly budget by sharing the amount among the months. The user wants to calculate it on the basis of the actual flow(over the months) of an unspecified account of the prior year. The unspecified account must be inserted in a data form.
So, i could use a Smart List but it colud be of 500 elements and then i should make a rule with as many IF as how many are the accounts. Or im wrong? The only way to use smart list dynamically in a business rule is by referring its values in a IF condition. Or i'm wrong.
I tried to use execution variable ma it seems don't work. In this case the user must pay attention to write the account correctly, otherwise as you say the rule doesn't work.
The value in PD0A020 is "PD0A000" (that is a dimensional member). The value in PD0A000 is "hello". In PD0A040 the rule returns "PD0A000" and not "hello" as i would. The function @Member appears to be not able to catch the dimensional member by the value in PD0A000.
{Example}="test"->"Input"->"Scenario_test"->"FY12"->"PD0A020";
Fix("test1","Input","Scenario_test","FY12")
"PD0A040"=@Member({Example});
endfix
So, my doubt is: is it possible for Essbase/Planning to use the value inserted in a data form and to turn it in a dimensional member? What are the practicable ways to let the user input/choose the member on which makes the rule run?
Thank you Ew, thank you guys
Maurizio

Creating a bootable Lion install disc/disk and using it

Hi all,
Below is a copy of a method ds store posted for creating a bootable Lion install disc. Some questions:
1. Is this a polished final version of the process, or are there other steps which could/should be added?
2. Are there any disadvantages to going this route instead of installing directly onto a Mac?
3. After creating a Lion install disc/disk via this method and using this saved dmg to install Lion on a Mac, will it set up the Mac exactly the same way it would by downloading/installing directly from the Apple Store (sounds like a "duh" question, but nothing would surprise me with Lion)?
4. Exact size of this dmg (in case I want to use a flash drive instead)?
I have been avoiding Lion, hoping it would shape up. I'm still not satisfied and will not run it on my main machines. (Of course ymmv; I'm not looking to be talked into or out of using Lion.) However, I am ******* (hmmm, I guess l-u-s-t-i-n-g is a bad word!) over a new Mac Mini, which will have Lion installed, with no chance of running SL on it due to the new hardware revision. Thus, I'm either going to have to make peace with Lion or forget about a new Mini. I guess I'll have to give Lion a try, but I still don't want to actually run it on any of my machines; thus, I want to run it from an external drive, playing with it as I have time/desire, leading to more questions.
5. Using the install disc/disk created above, will it set up Lion on a DVD, flash drive, or external HD exactly as it would on a Mac (Recovery Disk, etc.)?
6. How much space is needed on a destination disc/disk to install Lion?
7. Is it possible to boot from a different volume, mount this dmg, and install Lion from it?
8. Any advantages/disadvantages doing it this way (#7) as opposed to booting from the Lion install disc/disk created above?
9. Another method I'm thinking of using is to (after cloning my SL installation) actually install Lion on my MBP over my current SL installation (shudders violently ), clone it to an external HD, then erase/zero the MBP's HD and clone my SL install back to my MBP. Has anyone done this? Again, I'm concerned that Lion will do something goofy and leave some kind of footprint behind, like maybe messing with firmware; cloning my SL installation back to my internal HD would not reverse a firmware change.
10. Any constructive suggestions on anything related to any of these steps is welcome!
Yes, I've searched and read a number of responses, but I'm hoping much of the "discovery" phase is over, and there are some "solid"/refined answers by now. My bottom line is to be able to play with Lion without having to depend on it.
Thanks!
Backup Lion Bootable 10.7 Disk
Purchase and download Lion from the Mac App Store on any Lion compatible Mac running Snow Leopard.
Right click on “Mac OS X     Lion”     installer and choose the option to     “Show Package Contents.”
Inside the Contents folder     that     appears you will find a SharedSupport     folder and inside the     SharedSupport folder     you will find the “InstallESD.dmg.” This is         the Lion boot disc image we have all been waiting for.
Copy “InstallESD.dmg” to         another folder like the Desktop.
Launch Disk Utility and click     the     burn button.
Select the copied “InstallESD.dmg” as the image to     burn,     insert a standard sized 4.7 GB DVD,     and wait for your new Lion Boot     Disc to come     out toasty hot.
With this disc you can boot any Lion compatible Mac, andinstall10.7 just like you installed previous version of Mac OS X. Youcan even use Disk Utility's Restore function to image your Lion bootdisc image onto a external drive suitable for performing a cleaninstall on a optical-drive-less MacBook Air, or Mac mini server.

tjk wrote:
5. Using the install disc/disk created above, will it set up Lion on a DVD, flash drive, or external HD exactly as it would on a Mac (Recovery Disk, etc.)?
DVD: no, flash drive: if it's large enough, external hard drive: yes
6. How much space is needed on a destination disc/disk to install Lion?
Whatever Apple minimum requirements are.
7. Is it possible to boot from a different volume, mount this dmg, and install Lion from it?
possibly, never tried it, it is a dmg so it's a volume all to itself, except it can't install to the same media it's on and can only install to something formatted with GUID and a OS X extended format, like a flash drive or hard drive large enough.
DVD's can't be formatted with a GUID EFI partiton
8. Any advantages/disadvantages doing it this way (#7) as opposed to booting from the Lion install disc/disk created above?
Speed limitation of the media and bus your using, USB 1 is a slower than a hard drive with 7,200 RPM on a Firewire 800 port
9. Another method I'm thinking of using is to (after cloning my SL installation) actually install Lion on my MBP over my current SL installation (shudders violently ), clone it to an external HD, then erase/zero the MBP's HD and clone my SL install back to my MBP.
The problems come from installing Lion over a existing Snow Leopard setup that isn't quite pristine enough for Lions quirkyness, has tweaks or other software installed that breaks 10.7, requiring you to fix it.
You can try it, you've got the 10.6 clone to option boot off of and restore from.
Cloning back and forth is a performance enhancer, not a problem solver.
Ideally it's best to clone 10.6, disconnect, zero and install 10.6, same user name, then up to 10.6.8, then to 10.7, then install programs from fresh sources/copies and then files returned last from backup off the clone (no migration assistant or it brings trouble back)
This will ensure the best possible performance possible with the least trouble as everything is wiped and installed fresh. Only problem being your files it there is something wrong with them, which is easy to remedy to the cause as it's the only thing not pristine.
Once you've got a pristine system, then clone that twice, once for a immediate update other for falling back a week, two weeks or even a month back.
Has anyone done this? Again, I'm concerned that Lion will do something goofy and leave some kind of footprint behind, like maybe messing with firmware; cloning my SL installation back to my internal HD would not reverse a firmware change.
Firmware is hardware specific not OS specific, of course it's possible a old version of a OS won't work with newer firmware, like 10.5 for instance perhaps because Apple has dropped all work on PPC code.
10.6 and 10.7 are just fine with most all present firmware, however there will be a time where a new firmware update could disallow 10.6, likely when iOS X 10.8 Bobcat arrives.
10. Any constructive suggestions on anything related to any of these steps is welcome!
Yes, I've searched and read a number of responses, but I'm hoping much of the "discovery" phase is over, and there are some "solid"/refined answers by now. My bottom line is to be able to play with Lion without having to depend on it.
Cloning only clones the Lion OS X Partition, not the Lion Recovery Partition.
A comptuer that is Lion capable will boot off a media with no Lion Recovery Partition.
You need to create a Lion Disk Assistant USB which copies your Lion Recovery Partition.
It's in my post.
https://discussions.apple.com/message/16276201#16276201

How do I use the CASE statement in the where clause?

Hello Everyone,
I have 2 queries that do what I need to do but I am trying to learn how to use the CASE statement.
I have tried to combine these 2 into one query using a case statement but don't get the results I need.
Could use some help on how to use the case syntax to get the results needed.
thanks a lot
select segment_name,
product_type,
count (distinct account_id)
FROM NL_ACCT
where
ind = 'N'
and
EM_ind = 'N'
and product_type in ('TAX','PAY')
and acct_open_dt between (cast('2006-01-17' as date)) and (cast('2006-01-17' as date) + 60)
GROUP BY 1,2
order by product_type
select segment_name,
product_type,
count (distinct account_id)
FROM NL_ACCT
where
ind = 'N'
and
EM_ind = 'N'
and product_type not in ('TAX','PAY')
and acct_open_dt between (cast('2006-01-17' as date)) and (cast('2006-01-17' as date) + 30)
group by 1,2
order by product_type

Something like:
SELECT segment_name, product_type,
       SUM(CASE WHEN account_id IN ('TAX','PAY') and
                     acct_open_dt BETWEEN TO_DATE('2006-01-17', 'yyyy-mm-dd') and
                           TO_DATE('2006-01-17', 'yyyy-mm-dd') + 60 THEN 1
                ELSE 0 END) tax_pay,
       SUM(CASE WHEN account_id NOT IN ('TAX','PAY') and
                     acct_open_dt BETWEEN TO_DATE('2006-01-17', 'yyyy-mm-dd') and
                           TO_DATE('2006-01-17', 'yyyy-mm-dd') + 30 THEN 1
                ELSE 0 END) not_tax_pay
FROM NL_ACCT
WHERE ind = 'N' and
      em_ind = 'N' and
      acct_open_dt BETWEEN TO_DATE('2006-01-17', 'yyyy-mm-dd') and
                           TO_DATE('2006-01-17', 'yyyy-mm-dd') + 60
GROUP BY segment_name, product_type
ORDER BY product_typeNote: You cannor GROUP BY 1,2, you need to explicitly name the columns to group by.
HTH
John

Audigy 2 ZS and using PC Case por

Similar Messages

Maybe you are looking for