Audigy 2 ZS/Lost sound Output Rear speakers 5.1(line out

I seem to have no output on lineout #2. Can switch speaker plugs to line or 3 and then get sound from rear speakers.
I believe i might have something wrong with card,It's set for 5.,only frt.lft & rt center,sub seem to work.Any Ideas out there?
Thanks in advance! Windows XP SP-2
P4-2.4OC'd to 3.4// 4-20 gig HDD's Raid 0//Rocket raid 640 pci card//2 Gigs PC4000///audigy 2 ZS//MSI 865 Neo-2 Platinum//
NEC 3500 DVD & TDK 880 GDVD Burners//Gainward golden Sample FX5700 UltraMessage Edited by Biggunn on 05-25-2005 :3 PM

OK , Perhaps i didnt Say this at first But, My speakers,souncard,etc. all Were working fine previously. Just This Past week or so i have lost sound to my rear speakers. The speakers i am using are logitech Z-5500's. As i stated earlier, i can switch speaker connections at soundcard and get sound from the rear speakers. I have tried these speakers on another computer(audigy LS card) and they work on that one without any problems. I have tried the speaker settings console where it shows you a diagram of 5. layout and sound coming from each speaker as it goes around the diagram,it is showing sound symbol for rear speakers but, no sound out of speakers in rear. The creative diagnostics has been run and everything passes in it and shows no problems.

Similar Messages

  • Soft sound from rear speakers while playing mov

    Hi,?Gaming and music is done via all speakers (i'm using analogue connection) just fine, but when i play a movie (using powerdvd 6?deluxe) i get faint sounds from the rear speakers. I had contact with creative's help desk in my country and we ran thru all system settings (e.g. thnx console). Everything was configured correctly., tho still a weak sound from rear speakers. They could not help me further ?I'm using a x-fi fatality soundcard with a logitech z-5400 speakerset.
    When running a movie it shows a logo near the system tray : dolby digital. I am hoping one of u has a solution to this problem. Greetz,?Nask

    In most of the cases, movies with mutichannel soundtrack do not use constantly every speakers. I think your case is normal and that's only your DVD's mix (as many DVD) that concentrates more on the front. try some of the sample there: http://www.digital-digest.com/dvd/do...s/trailers.phpIf the first one sound at the same level for each speakers then it's alright.

  • No Sound on Rear Speakers

    I have a new Lenovo H420and I am unable to get sound from the 2nd set of rear speakers when using a media player.
    The OS  is Windows 7 Home 64 bit and I have put in all new drivers for the Realtek HD Audio. When I run the Lenovo HD Audio Manager the system shows stereo or quadrophonic or 5.1 speakers. Stereo is fine and plays back on the front speakers. And when set to 4 speakers, the Audio Manager playback tests successfully on all 4 speakers. It does this also for the Windows speaker configuration.
    But running Windows media player or VLC player will only play sounds on the front channel. I am unable to find any information from Lenovo, Realtek or Microsoft about this problem, but I can find lots of other people with a similar issue.
    Any suggestions for a solution?
    Solved!
    Go to Solution.

    This problem with no sound on rear speakers has taken up far more time than I ever expected. I have un-installed and re-installed drivers and assorted  audio applications in an an attempt to resolve it. Internet research found many other people with the same frustrating problem with Realtek Audio and Windows 7. There seemed to be no one who had found a good answer.
    HERE IS THE SOLUTION!
    > Run the Realtek Audio Manager (aka Lenovo HD auido Manager)  found in the control panel programs.
    > Click Advanced button on right panel
    > Set  Speaker Configuration to Quadraphonic
    > Click the Test button or click on the individual speakers. You should hear sound from all the speakers except for the center channel and subwoofer. This proves there is a signal for the front and rear speakers. The problem is that when running applications there is no sound on the rear speakers.
    > Click Sound Effects tab, change the Environment  from <none> to Room.   There should now be an audio signal for the rear speakers!
    Why this is not explained anywhere on Realtek help or anywhere else on the internet is a mystery. But at least this is an easy if baffling fix. I believe that the Realtek Audio codex wants to process all sound through some kind of effects and delay engine. There doesn't seem to be any Fade control for Front and Rear. There is a Loudness Equalization that I also clicked that does some voluime adjustment but not much. The Rear speakers will not play for many of the odd  Environments, I found Room, Auditorium, and Concert Hall to be acceptable. Perhaps others like Sewer Pipe may be suitable for games. Most are just silly noise effects.
    The equalizer has some useful qualities and can adjust the bass/treble audio to suit music. The Live was the best for my speakers which are Logitech. The sub-woofer may need some adjustment depending on the carpets or tile in the room.
    Hope this helps someone to resolve this wierd audio problem.

  • Why no sound from rear speakers (Xfi X

    Vista 32bit, CMSS enabled, why no sound from rear speakers with music? XP no problem at all, only in Vista. Using latest drivers (v2.5.0004).
    I realize I'm hoping against hope to get a useful answer at the Creative forums, but I do believe in miracles and the odd one happening once or twice in a lifetime, lol.

    Well, I think I have an answer, from Catherina-CL's Audio in Windows Vista post. 2.The Vista audio architecture changes the way per-stream audio processing works, which required us to write new software to support this
    Issues that may be encountered:
    CMSS no longer works on audio streams from the OS.
    Status:
    Features based on Windows XP architecture must be rewritten to conform to the new Vista architecture, and we have a team of software engineers, project managers and testers dedicated to this task in order to provide our customers the same seamless audio experience under Windows Vista that they enjoyed under Windows XP. However, I found a somewhat crappy solution, at least with my old Altec Lansing 4 speaker/ subwoofer system. Unplug the surround cable from your subwoofer (unplugging it from the card itself has no effect). That at least will make all the speakers work, even if it's not true surround. Good for listening to music loud.

  • Qosmio X770-11C - how to disable on board speakers when using Line Out?

    Hi,
    Is there any way to disable on board speakers when the line out is used.
    Currently if I plug in a cable to the hadphone socket and choose lineout on the realtek control panel, the sound is output to the line out as expected but also through the internal speakers.
    Is there any way to stop this, and only have sound going out through the line out?
    thanks
    Graeme

    If you want to hear sound on headset only you must choose Headphone option.
    Disconnect cable and connect it again. When you see small window on the screen where you can choose between headphone and line out options choose headphone and you will hear sound on external device only.
    In case you have disabled this popup dialog you can activate it manually. Open Realtek manager connect external device and when you see activated black point on the right side make double click there and change settings.

  • No sound from rear speakers; SB audigy 2; Logitech X-530; CMSS is enabled; Win

    I have the above setup but am getting no sound out of the rear speakers.
    I have tried the self-help route of looking at all of the suggestions to prevois posters, and tried as many as seemed different. eax -> cmss CMSS is turned on (CMSS2 also tried, but still no sound). Drivers reloaded, and updated fromt eh Creative web site. Other sound-related hardward on the PC are: Guitarport - this connects into the line in on the SC card and a Philips SPC900NC webcam with a built-in microphone. I saw a rreply on a Logitech webcam causing issues because of the echo cancelling. Cannot find any equivalent in the philips tho'. Any help appreciated. Thanks

    Hello,
    I am running into the same problem. I had a audigy and the sound test would not output sound to the rear or center speakers. I then tried an x-fi card - same problem.
    I also tried a different set of speakers... I am pulling my hair out here. This used to work great, can't figure it out. When I run through the speaker test with the x-fi, I hear everything coming out of the front two speakers. It says "rear right" out of the front right speaker. It also says "front right" out of that same speaker.

  • Sound from REAR speakers o

    Hi,
    I have a SB Audigy 4 and a Cambridge SW 5. speaker system running on Windows XP SP2. I recently re-OSd my system and everything was working fine. I was in the middle of a web-cam call and all of a sudden the sound disappeared. I have a Logitech QuickCam, and I understand that its software can interfere with the surround speakers (usually by disabling the rear speakers). Anyways I unistalled all the Logitech software, but still no sound.
    I uninstalled and reinstalled my Creative drivers multiple times, and all I can get is sound out of the rear speakers. Nothing out of the front or centre speakers. The AudioHQ speaker test only has sound coming out of the rear. Also, when I play music (e.g. mp3s) it comes out of the rear speakers as well (I thought this was odd as usually stereo sound comes out of the front speakers doesn't it's)
    Anyways I've tried switiching the front and rear speakers, and the front speakers work out of the rear channel, so it's not that. I don't know what else to try. I've checked all the connections, etc and nothing. Anyone have any ideas?
    Thanks

    Have you checked that the cables are mounted OK (i.e. is cabling OK in speaker system ... try by using stereo connection for every pair at once ... connect rear channel cable(s) into X-Fi front output ... connect center/sub into front output) ... are these OK.
    Propably you could switch those rear/cent-sub cables as a temp. solution but, would it be a resolution ... well, it's up to you?
    Are your sources stereo (i.e. you need to use CMSS to convert stereo signal to multichannel)?
    BTW, I had similiar issue in my Audigy 2 card before latest driver update.
    jutapaMessage Edited by jutapa on 06-06-200703:24 PM

  • No Sound From Rear Speakers unless CMSS-3D is on XFI Elite Pro

    Hello Guys,
    I have always had issues with my rear sound and nothing has changed. I am begining to think my sound card is broken. I bought this refurbed or open boxed directly from creative so maybe this is the reason? I want all the speakers to sound the same and even if I enable the CMSS3D they do not sound like the front ones. It seems distorted and not as clear and the volume is lower. Any ideas?

    Hello,
    I am running into the same problem. I had a audigy and the sound test would not output sound to the rear or center speakers. I then tried an x-fi card - same problem.
    I also tried a different set of speakers... I am pulling my hair out here. This used to work great, can't figure it out. When I run through the speaker test with the x-fi, I hear everything coming out of the front two speakers. It says "rear right" out of the front right speaker. It also says "front right" out of that same speaker.

  • Muffled sound from rear speakers (t7700)

    I hooked up new T7700 speaker set up to my new Audigy 2 ZS Gamer and when i watch movies or play games i hear nothing from my rear speakers. if i put my ear right by them then i hear that there is sound coming from them but very quietly.
    side front and center work fine any ideas?

    That would be normal for a 5.1 system, rear is very discrete.
    Use the speaker test and you should hear the level increase. or use cmss to play cd music to back 2 speakers.
    [edit] sorry didnt see the bit with side speakers.
    Select 5.1 instead of 7.1
    if you still want to use 7.1 then check the settings in the decoder bit and look at where you are mapping the speakers to. like in a 7.1 speaker configuration map 5.1 content to etc\
    For 5.1 movies use the rear mapping, or the side mapping,
    if you want all the speakers on then select the side and rear option then whatever sound you get from the speakers will be a bonus.
    Message Edited by dontasciime on 01-20-2005 10:06 AM

  • Stereo Sound to Rear Speakers Only / Dolby Digital

    Just purchased a Toshiba 40S51U LCD TV.  Having an issue with the sound when connected to a receiver via the optical out. 
    I think the issue is as follows:  When the program (ie local news) or commercial is broadcast in stereo, the sound is sent only to the surround (rear) speakers.  Sound is great (surround works just fine) when watching a show.  Assuming the shows are broadcasting 5.1 sound, local news only 2.0. 
    Signal is over-the-air. 
    I can switch the sound output to PCM and get reasonable sound for everything, but obviously lose the surround sound.  Would like to keep the system in Dolby Digital (AUTO) all the time. 
    Thanks,
    Rob
    Solved!
    Go to Solution.

    Me again -- I'm an idiot and the TV was just fine. 
    My receiver was set to a non-connected set of speakers -- not sure why anything was working!  I changed the speakers to the set actually connected and everything seems to be working OK now.  The optical out on the TV was likely never an issue. 
    Rob

  • No sound in rear speakers with Sound Blaster Li

    I have a Sound Blaster Li've sound card.. In win98 with older drivers it was possible to set the card to 5., but now (in winXP and newest drivers) there are these thrre optins: headphones, 2 speakers and 4 speakers... I use digital output and I have 5. speakers. I can li've with only 4 speakers but it does not work very good.
    When i press the test button i hear the front left voice and the front right voice correctly in the front speakers, but i hear both voices in both rear speakers. But then the test is supposed to say rear left and rear right, but there is no sound. My receiver is a Harman/Kardon AVR 550 and is set to dolby pro logic and 5. speakers.
    How do I solve the problem!

    All,
    Are you using the Li'veDrvUniPack from our website or using the default Windows Driver? If you are using the default driver then there will be limitations. You will need to install the complete Li'veDrvUni-Pack from our downloads section to get 5. if you have a Li've! 5. card.
    Jeremy

  • No sound on rear speakers (X-

    ok I just upgraded from my old soundblaster li've! 5. and im having a few problems so far. first the rear speakers wont work when playing from windows media player, itunes etc (they work with 5. content though) i tried the cmss 3D thing but it doesnt do anything at all, i dont see any change in the sound.
    i have
    windows XP sp2
    AMD Athlon X2
    nvidia 6800 gs
    what could I be doing wrong? it worked fine with my old card

    osmel wrote:
    ok I just upgraded from my old soundblaster li've! 5. and im having a few problems so far. first the rear speakers wont work when playing from windows media player, itunes etc (they work with 5. content though) i tried the cmss 3D thing but it doesnt do anything at all, i dont see any change in the sound.
    i have
    windows XP sp2
    AMD Athlon X2
    nvidia 6800 gs
    what could I be doing wrong? it worked fine with my old card
    Maybe there is something to learn first .
    I have not the catd, but IIRC --> on creation mode --> route the output to front and rear.
    jutapa

  • Xi-Fi: No sound from rear speakers in Vi

    Hey everybody, I am not hearing any sound from my rear speakers (I have a 5. setup) in Windows Vista. I have of course updated to the latest Vista driver for the Xi-Fi card, all of my connections are correctly set up on my hardware, and I have made sure that I have 5. Speakers selected in the Xi-Fi Volume Panel.
    The strange thing is, if I go into the Windows Sound panel from the Control Panel and do a test from there, I *do* hear sound from my rear speakers, however this is the only time I can hear it, not while listening to music, watching movies, or playing games.
    If anyone can help me with this problem I'd be deeply appreciati've. Thanks!

    Unfortunately, I have gone through 2 SoundBlaster cards on my Vista machine and am _still_ having this same issue. On my XP machine everything worked great with my Audigy 2 card... once I upgraded to Vista, nadda (and not to mention all the cool features & software that worked on XP didn't work in Vista)... so I upgraded to an X-Fi Fatalty Platinum card after reading on the Creative website that most functionality had returned with the new drivers (including CMSS supposedly). While some of the software is now available, the whole reason I upgraded my card was so that CMSS would work!
    Like everyone else, I have CMSS enabled and when I do the speaker test in Windows & Creative Audio Console, I hear test tones from the rear speakers. However, when I listen to music or do anything else involving audio, I get nothing from the rears (unless I turn on one of the effects which I don't want as they mess with the sound too much - and even then, I only hear a slight reverby effect from the rears on certain effects). I am extremely disappointed that I spent a lot of money (much more than most good soundcards) and STILL HAVE NO REAR SOUND!
    Also, is anyone getting a warning when opening the Sound options in Windows Control Panel? This is what I am getting:
    http://www.snapdri've.net/files/56394/AudioEnhancements.JPG
    Which tells me that something isn't right... I am hoping it is due to remnants of my audigy drivers... this is the only reason I have a glint of hope - and this: after googling this issue, I did find another forum discussing the same issue and one person was actually able to resolve it... here was his solution:
    "I uninstalled the drivers for the third time, but this time went into my creative folder and deleted all of the audio console files and what not that there was NOT an uninstaller for. I then rebooted. I redownloaded and reinstalled the latest drivers from the website. I rebooted again. I then downloaded the latest vista audio console launcher and installed it. I then rebooted again. I turned some music on and the CMSS works now! And it sound SO much better! IT EVEN GAVE ME MY MIC OPTIONS BACK. The only thing I can think of was that I had an old XP version of the audio console, and thats why the CMSS didn't work, and it took away my mic options."
    If anyone does resolve this issue, PLEASE POST YOUR SOLUTION HERE! Thanks - it would be much appreciated and would surely be helping out many others with the same frustrating problem.

  • Completely lost sound on both speakers & mic on my new HP2000

    I completeley lost sound on my new HP2000 that I bought 2 weeks ago. Both the speakers and mic are not working. I would appreciate any hep that you can extend, or I will just return this new laptop to Best Buy! Thanks in advance. 

    Just rolled back the driver to the beta one and Line In sound is restored. I know when to chnage gear on the 360 now!?Seriously CL need to sort their act out, Vista has been known about for years and has not suddenly appeared out of nowhere. If everyone else can get a working driver out in time (apart from Nvidia) why the hell can't CL?

  • Sound output only has option for Digital Out, no internal speakers, and no headphones.

    I recently got a new 2012 Macbook Pro 15" and my sound output is not working correctly. The only option is Digital Out - Optical digital-out port. There is no intenral speakers option, nor is there a headphones option when I put them in. I am running Mountain Lion and unfortunately have tried looking up similar posts with no help. I have attempted to reboot the SMC and perhaps one other trick, but I have not had any luck. If anyone has any idea what I should do or if you need more information to make a diagnosis that would be great! To note, it worked fine when I first got the computer, but when I was messing around trying to hook my computer up to an HDTV (i have a thunderbolt HDMI cable that sends sound as well) I had a couple of problems (I think it was because it was a very old Vizio that did not support the HDMI) and perhaps some of the settings got changed on my computer. Anyways thanks in advance!

    Hi,
    That is good news! For some reason I only experienced that for a little while before it straightened out itself. But I know that was driving a lot of people crazy. Thanks for pointing out that 10.6.2 did the trick.

Maybe you are looking for