Audigy 2 zs platinum front drive bay mic2 not worki

hey all I finally got my AD_EXT wire to make my audigy 2 card work with the front dri've bay but the problem now is I am in vista ultimate 32bit, all drivers installed right, all cables plugged in but the mic2 is not working....... I'm using a dynamic mic Samson Q7 microphone with the XLR cable. This microphone I heard does not need a preamp so it should powered up.
I called creative and the guy supposed to send me a article to read to fix it but so far no luck in my email about it.
anyone staff members here know the link to that article?

Maybe this will help out:? Under Control Panel ---> Sounds and Audio Devices --> Hardware I have the following list. CD-RW SOHR-5239SDVD_RW ND-3550AMPU-40 Compatible MIDI DeviceUnsupported Standard Game Port - Location: on PCI BusCreative SB Audigy 2 ZS (WDM) - Location PCI Slot 2 (PCI bus 5, Device 7, Funtion 0)Creative Game Port - Location: PCI Slot 2 (PCI bus 5, device 7, function )Audio CodecsLegacy Audio DriversLegacy Video Capture DevicesVideo Codecs?All of them are listed as "Working Properly". The MPU-40, the unsupported game port, creative SB Audigy 2 ZS, Audio codecs, legacy Audio Drivers, and the Creative Game port were all uninstalled prior to my latest re-installation. When the windows install wizard popped up, I cancelled, so everything on that list was installed using the latest creative ZS Platinum driver for x64.

Similar Messages

Audigy Platinum eX External Bay is not work

So I posted a few days ago with this same problem. My external bay is not working, and not even getting power. I uninstalled my Audigy, removed the card and put it in a different PCI slot. Then I reinstalled it. I also unplugged all cables and then put them back in to make sure they are well attached. Still I have problems, and the external bay is useless and unpowered. Anyone have any ideas?

LoopyG,
If you have done all of these steps and you are still not getting any power from the dri've bay then you will probably want to contact Technical Support to arrange repairs. Their contact page is: http://us.creative.com/support/custsup.
Jeremy

T430s 2nd Hard Drive Bay Caddy not working

Hi all,
I bought 2nd Hard Drive Bay Caddy for my T430s but it does not seem to work.
The HDDs I placed in it do not even start to spin, and they are not recognized by the laptop BIOS as also by my OSes, Windows and Linux.
The label on the caddy says it is P/N 26r9247, but at this stage I'm not sure is a compatible part or if I got just a faulty item.
Any feedback?
Solved!
Go to Solution.

That part number (26R9247) is for the older T60/61 Thinkpads. You need the Ultrabay III adapter. Look at 43N3412.

T43 2nd Hard Drive Bay Caddy not working

I installed a generic ultra bay caddy and the new drive isn't recognized.
It works fine in an external enclosure.
Any suggestions?

goretsky wrote:
Hello,
Do other Ultrabay caddies work in the T43 or does this one work in other ThinkPads?
Regards,
Aryeh Goretsky
The caddies for a T60/61 (also R and Z series) will work if you remove a plastic tab that prevents them from being inserted in a T4x or R5x series. The faceplate looks slightly different but it's not objectionable looking when installed.
ThinkPad W-510 i7-820QM(1.73-3.06GHz) Quad Core... ThinkPad T500, T9900, 8gb SSD...FrankNpad T-60p/61p (X9000 2.8ghz) 8gb SSD ips FlexView...ThinkPad T-61p (T9300 2.5ghz) 8gb ram...Thinkpad X-61 Tablet 4gb ram...ThinkPad A-31 (1.9ghz P4 1.5gb ram)

Problem with Audigy 2 Platinum Front Panel Input

0Problem with Audigy 2 Platinum Front Panel Input? Hey everyone,
Here's the background of the issue. I got a PS3 over the holidays for literally free
I had my computer out in a testbed style. Plugged the PS3 into my monitor HDMI --> DVI cable, and Red/White into the front RCA jacks of the Front Panel (Aux 2). As soon as I plugged in the cable, I got sound out of my speakers and was able to enjoy my PS3 in 720p
I put all of the components back into the case after cutting exhause and intake fan holes. I brought everything back to school, fired up the PC and PS3. Lo and behold, there is no more sound from the PS3. I know that PS3s are temperamental in moving, but I hooked the audio up to my TV and the sound came out just fine. The AD Ext cable looks like it's secure and in place. When I hooked up a mic and headphones to the front, they worked fine as well. However it seems to be just the AUX 2 RCA inputs that dont work anymore. Any ideas about how to fix this issue? Is there a function I have to turn on now in the software to allow sound to pass through? Any information would be wonderful!? I'm going to try an optical cable in the near future, just need to borrow one from a friend =/

Problem Solved.
I had moved my cards around for better airflow. I moved the SB Audigy card from the bottom PCI slot to the top. Thinking this might be the problem, I moved the video card back to the top slot PCI-E and the sound card to the bottom PCI slot. Sound is now working again. Thanks for the thread views?:smileytongue:
Think that when I have to buy Win 7 for real if the problem would still persist if I moved the card again? Or is this a hardware limitation?

I have 4s iPhone , I download the iOS 7. Now the front receiver microphone is not working , please help me that how to fix the problem.

I have 4s iPhone , I download the iOS 7. Now the front receiver microphone is not working , please help me that how to fix the problem.

I live in South Africa, and I had the same problem with my iPhone 4.
After weeks of frustration and swearing, I was in the process of restoring my phone to a previous iOS. To do that you need to turn the "Find my iPhone" option off, since i turned it off, my problem was solved. No need to repair anything or revert back to old iOS.
***** that i cant use Find my iPhone, but atleast i can use my phone.

Equium A300D - Toshiba ATI display driver upgrade is not working

Hi
Has anybody else found the Equium A300D PSAK2E Windows Vista 32 bit Toshiba ATI display driver download will not work from the download centre? If you choose run, the download causes the windows explorer to crash during the install and the upgrade fails, the same with save and the install does not self install.
I have been trying to get the TV out S-Video port working. See thread on TV out not working. I have tried everything. has anybody else got this problem as Toshiba are unaware of any problems with the S Video TV out not working on this machine.
Thanks Vince

Hi,
The down load downloads ok but when you try and unzip it, then install it halfay through you get an error message stating windows explorer has stopped working and it has crashed. The Graphic card then will not work. I have tried uninstalling all the ATI software and deleting the left over files but it still wont install.
I have downloaded the programme from the ATI site and this installed ok and the graphic card is working. The s video tv port still will not work.
I have gone into great detail on the post regarding the TV out not working about what i have done. When the s video lead is connected the computer can see the tv but will not output, when you try and enable the display the display will not enable. I have used the FN f5 key with no success, changed settings on the avi controller and display settings in the control panel
I will take the machine back to where i bought it from next week and see if they can get it to work!

Help!! T6060 5.1 Front right speaker is not working properly!!

I have new Inspire t6060 5.1 speakers, but i have problems , because on riht side speaker is not working!! all speakers are working good, only one front right speaker is not working i have altec 97 (asus intergrated suond card), i have tryed to instal new audio drivers , but it has not solved the problem. there is the problem? plz help!!

Here here, you are not the only one.
Have absolutely no solution to this problem apart from sending it back and never buying anything Creative ever again.
They refuse to acknowledge this problem.

Can Audigy 2 Platinum front panel connect to X-fi?

Hi,
I'm about to build a new i7?system and am debating buying an X-Fi Titanium (non-fatality)?to replace my Audigy 2 Platinum. Is it possible to connect the front dri've bay from the platinum to the X-Fi card? If not, I'm wondering if it is worth the switch. I'm not keen on paying any more than the price of the standard titanium card, so am not looking at the pro, etc.
I'd appreciate any thoughts. Thanks!
Message Edited by motility on 05-05-2009 09:44 AM

Oh well, it is already ordered. It is rather absurd in this day and age that Ceati've charges 00 plus dollars premium?for such simple functionaility. Even M-Audio seems to provide better connectivity solutions on its low end interfaces. I have one of those. Guess I can just get an RCA to /4 inch or XLR adaper.
Still looking forward to the X-fi, though,

Audigy 2 Platinum Front Panel Probl

Hello everyone. Thank you in advance for any help.
My problem is two-fold, let me begin with the first issues.
Critical Issue One: On my Audigy 2 Platinum neither the headphone jack nor the Line 2 in/Mic 2 in jacks appear to be at all functional. I can get no sound to go in or come out using them. Additionally, I don't see a volume slider to control either of them in the surround mixer. Is it possible somehow that the entire front panel is disabled? I looked inside my computer and it appears to be connected firmly (the AD_EXT cable is the only one connecting my sound card to anything internally). As a side note I have already tried doing a full, clean reinstall of the drivers, to no avail.
Issue Two: I can no longer auto update my drivers using Creative's site. I believe this is somehow related to IE7, it always functioned perfectly with IE6. When I try to update now the message I get is: "Some components are corrupted." I did a search in the knowledge base and followed the instructions to fix this problem (Deleting the Acti've X controls) but this does not resolve the issue (I also noticed by searching the forums that people with similar problems never found a resolution beyond "doing a manual driver install"). I believe that the acti've x controls that I am downloading get corrupted each time. Is it possible that someone could send me, fully functional non corrupted creative acti've x controls that I could install? Or is this simply an incompatibility between the creative site and IE7?

Hello everyone. Thank you in advance for any help.
My problem is two-fold, let me begin with the first issues.
Critical Issue One: On my Audigy 2 Platinum neither the headphone jack nor the Line 2 in/Mic 2 in jacks appear to be at all functional. I can get no sound to go in or come out using them. Additionally, I don't see a volume slider to control either of them in the surround mixer. Is it possible somehow that the entire front panel is disabled? I looked inside my computer and it appears to be connected firmly (the AD_EXT cable is the only one connecting my sound card to anything internally). As a side note I have already tried doing a full, clean reinstall of the drivers, to no avail.
Issue Two: I can no longer auto update my drivers using Creative's site. I believe this is somehow related to IE7, it always functioned perfectly with IE6. When I try to update now the message I get is: "Some components are corrupted." I did a search in the knowledge base and followed the instructions to fix this problem (Deleting the Acti've X controls) but this does not resolve the issue (I also noticed by searching the forums that people with similar problems never found a resolution beyond "doing a manual driver install"). I believe that the acti've x controls that I am downloading get corrupted each time. Is it possible that someone could send me, fully functional non corrupted creative acti've x controls that I could install? Or is this simply an incompatibility between the creative site and IE7?

Audigy 2 Platinum Front Panel Connecti

I recently began recording my band in our home studio. My mixing board is a Midas Venice 240 which has two balanced XLR outputs from the master bus. I am wondering what method I may use to connect this output to the /4" stereo input on the front panel of the Audigy 2 Platinum. If I just purchase a Y-adapter to combine the two channels into one XLR and then convert it to /4" TRS jack will both channels be preserved? Are there any sound quality issues that arise from this method of connection? I was hoping to get answers to these questions before wasting money buying unnecessary adapters.
Thanks

The BEST way to do this is to go to radio shack and buy two (yes 2) of their?XLR to /4" Impedence Matching Transformers, AND?one (yes )?dual /4" female TS (tip-sleeve) to single /4" male TRS (tip-ring-sleeve) "Y" cable. Unless your mixer also has /4" main outs as well as the XLR... then you can just use the Y cable and skip the transformers. Or you can use a /8" Y cable with the transformers (and stereo /4 to stereo /8 adapter) and go into the card's line in jack on the actual card. Which is how I did it for a year or more untill i got a firewire recording interface (and it worked darn good too with my Soundcraft mixer and some good microphones). Either way,?you need the transformers for optimal results. The reason is the mixer's output impedence and level doesnt match that of the soundcard's input... mixer will likely overdri've the card, or the signal will sound weak or noisy.. The transformers?are cheap and are darn handy for loads of recording functions, and will provide the Audigy with exactly the type of signal it needs, properly transformed from the mixer. If you do this, you can record ALL of the mixer channels IN STEREO with all the panning, effects, and levels preserved. If you have multitracking software like Cubase or similar, you can even record an individual instrument (or even 2 at once, one panned left, one right... each assigned its own track in your software), come back on a new track (or pair of tracks), and record a different instrumet (or 2) and build a multitrack recording one performance at a time. PS:? you CANNOT just hardwire the mixer outputs and combine them into a single channel. A mixer is needed to properly combine?signals. Don't do it
!!! Have fun... and rock on.PSS:? make sure your overall cable is as short as possible. If you must run it for more than 6 feet then run it in XLR mode and convert it very close to the computer. The non XLR section of cable is an antenna for noise. The XLR section will be shielded against noise. Also, the transformers are kinda heavy so do not plug them into somthing and allow them to hang in the plug becasue the hanging weight will ruin your jack. Its best to run cables to the transformers, allowing them to lay on the floor... in a safe place where they wont get stomped on.
Message Edited by ElectricUrinal on -28-200708:0 AM

Audigy 2 Platinum Front Pa

I recently suffered a hard disc crash. After rebuilding the system the front panel on my Audigy 2 Platinum does not appear to work.
Specifically, the firewire port on the front panel does not detect my iPod, whereas the firewire port on the card at the rear of the PC works fine.
Any ideas as to a) how I can find if the panel is working or b) am I missing some drivers?
Thanks
Phil

OK problem solved. The flat connector on the card at the back of the computer was very slightly loose on one side only. I could only tell when I actually tried to move it myself - it certainly looked OK. Strange that the audio made it to the speakers OK but not to the headphones!

Audigy 2 platinum front panel h

Hi
I have got a problem with my audigy 2 platinum. I want to be able to plug in a guitar or other audio devices for that matter into the front bay. However i go into surround mixer to enable the device but can't find line in 2 or aux 2 listed anywhere. So no sound is heard. I have confirmed there is power to the front hub by checking the optical connection and confirming there is a red light. How can i get the inputs to work?. How do i enable them?.
Any advice would be much appreciated.
Many Thanks
Chris

Hi
I have got a problem with my audigy 2 platinum. I want to be able to plug in a guitar or other audio devices for that matter into the front bay. However i go into surround mixer to enable the device but can't find line in 2 or aux 2 listed anywhere. So no sound is heard. I have confirmed there is power to the front hub by checking the optical connection and confirming there is a red light. How can i get the inputs to work?. How do i enable them?.
Any advice would be much appreciated.
Many Thanks
Chris

Audigy 2 Platinum Front jacks

I have a Audigy 2 Platinum sound card with the front panel for a mic, 394 hookup and so forth.What I need to know is what size jacks are used for the In and Out connections where you plug something external in . These are the connections to the left of the front panel.
Thanks for any help that you can give.

! Thanks KokChoy-CL
The RCA connectors you speak about are they same as the as rear connectors, 3.5 mm. If so they (3.5 mm) will not go in the front panel.Should they be real tight,I've never seen any this tight. I've had this unit since it was brought to market but, never used the in/out audio until now .We bought a wireless speaker system and I want to use the front panel as it is much easier to get to than the back.
Thanks for your help.

SB Audigy 2 ZS Platinum Pro - Micro Phone does not work correct

Drivers are up to date, everything is connected right running my 5. (7. would be up but of my creative speakers is defecti've ) my friend has the same set up and his mic was put into line 2, I get no sound through that, only line /mic and my mic is ALWAYS on (feed back and such). I use Ventrillio for games and this just doesn't work they way it's set up now, I hear things twice and I can't even adjust the volume normaly, I have to turn the knob on the external box.
Please Help.Message Edited by zdonner on 0-24-2005 04:34 AM

I have the same problem. The microphone input is not working. I have Windows Xp all the driver up to date and nothing. Dell has sent me a new board has we thought it was an hardware problem but it still not working. Actually I have to use the microphone input of the soud board included in the motherboard.

Audigy 2 zs platinum front drive bay mic2 not worki

Similar Messages

Maybe you are looking for