Audigy 2 ZS Platinum Pro and Inspire 5.1 Digital 5500

Hi!
Why can't i connect this digital speaker system to the external connection box of the Audigy 2 ZS? I've tried the optical as well as the coax-connection. When i run the surround soundtest in the Creative software it only gives me stereo sound in front left and right speaker.
It only works when i connect the speakers by analog connection directly to the soundcard, but then the volume settings for WAVE-sound in the Creative control panel has to be reduced to almost nothing if i wish to keep my ears.
If these speakers are'nt supposed to use digital connection....then WHY CALL THEM DIGITAL?
Message Edited by perssoe on 08-20-2005 07:48 AM

Read the FAQ on top of the soundcard forum concerning SPDIF and digital out. The reason is very easy to find out if you read that. In short: the digital out can only send out a PCM stereo signal (which is why you only get FL/FR sound) and an encoded AC-3 signal.

Similar Messages

Audigy 2 ZS Platinum Pro and Inspire T7700 does not recognize Mic on Audio Control

Hi folks,
I decided to hook up my headphone and mic sets to the Audio Control Pod for the first time recently to chat online. I'm not sure if I ever tried this when I bought the Inspire T7700 speaker system, but I cannot seem to get any voice to come through in Windows' Sound Recorder (the headphones work fine). I'm hoping that someone here can help...otherwise, I suppose I'll have to find an alternate solution than using my soundcard system.
Here are some specs:
OS: Windows XP SP2 and all current updates
Soundcard: Audigy 2 ZS Platinum Pro
Speakers: Inspire T7700 with Audio Control Pod (contains the headphone and mic jack)
Here's what I have tried:
. Updated drivers to: SBAX_WBUP2_LB_2_09_006.exe
2. Tested headsets and mics out on another one of my computers with a SoundBlaster Li've. They work fine.
3. Set each audio source with full volume in the Recording Control window as the source while recording in Windows' Sound Recorder (I know some of these aren't right, but I tried them all nonetheless):
- MIDI Synth
- Line-In 3
- Line-In /Mic (this should be the one, I think)
- S/PDIF-In
- Auxiliary (this might be the one for the Audio Control Pod)
- "What U Hear"
- Line-In 2
- CD Digital
- Wave
4. Installed the Creative software from the official CD to manage the audio and speaker settings. Retested the same as item 3 above within this software. Same results.
5. Disconnected the external I/O hub (since I am connecting to the Audio Control Pod, which connects to the speaker system and then my sound card). Interestingly, the Line-In /Mic input disappeared. All that I saw for an input (I believe) was Auxiliary. I tried even that as noted in item 3, but nothing.
Has anyone had any luck in getting a mic from a headphone set to work with the Audio Control Pod for the Inspire T7700 speaker system along with the Audigy 2 ZS Platinum Pro?
Thanks in advance for the help!

Read the FAQ on top of the soundcard forum concerning SPDIF and digital out. The reason is very easy to find out if you read that. In short: the digital out can only send out a PCM stereo signal (which is why you only get FL/FR sound) and an encoded AC-3 signal.

Audigy 2 ZS Platinum Pro and XP

I have Audigy 2 ZS Platinum Pro and Logitech Z-5300 5. Speakers. When using XP SP, everything worked perfectly, then I upgraded to SP2. It has been a complete multimedia nightmare.
When using the diagnostic tools, each speaker works perfectly except will always have a faded voice to the point where I cannot hear the voice but I can hear something was attempting.
WinAMP or Media player or any other MP3 player to include tools coming with creative labs products, I get music only out of a single (Center) speaker. The rest lay silent. I upgraded my sound card drivers using Creative Lab's website. Any ideas how to get my system back to normal sound quality, as of this moment I am thinking creative lab's products do not work correctly under SP2.
Any help would be appreceated and for the money spent on the card, I kind of expect creative to have a solution.

Roaming,
Try cleansweeping and reinstalling the sound card. Sometimes after a major update (like a service pack) some hardware or software needs to be reinstalled. Here is a link to the article that describes how to cleansweep your card.
http://us.creative.com/support/kb/ar...asp?l=2&sid=72
Jeremy

Audigy 2 ZS Platinum Pro and ASUS P5W DH Deluxe Motherbo

I am currently trying to get my soundblaster Audigy 2 Platinum Pro to work with this board. I have dis-abled the onboard sound but still no luck. Has anyone managed to get this to work? I am currently using the so called Hi quality onboard sound but it's nowhere near as good as my dedicated card. Any help would be appreciated.
Thank you...Rob

Is there no one out there that can help?

Audigy 4 platinum pro Microphone im

Simple one here, i'm just about to buy some leads to connect my condensor mic to my external hub. I just bought a preamp, yet don't have all the leads for it to work. Will a 'balanced /4" TRS connector' fit into the 'Mic imput'/'line-in' of my Audigy 4 platinum pro soundcard? This is opposed to an 'Unbalanced /4" TS connector'. Help will be appreciated! Carry on being CREATIVE
P3U6!SUn 3H+

Hi there,
I nearly freaked out when I got the platinum pro as I thought I could get no decent power in direct guitar and microphones. You said you bought a preamp, but there is a preamp switch for Line In/Mic on the front of the hub. I have been using this for boosting mic and guitar signals and it is okay but was wandering what preamp you bought and if you rate it.
Hope I haven't upset you by telling you about the built in pre-amp as it probably isn't the best quality anyway.
Cheers,
Paul D.

Connecting vcr to external SB Audigy 2zs Platinum Pro

I've just joined, so apologies if I "mess up". I have some precious things on vhs tape, and want to transfer them to cd/dvd. I run Windows XP. I have to use rca connections, don't think there's another option on the vcr. I see the red and white rca connections on the back of the external 2zs, but where does the yellow (video) connection go? Would be very grateful for help. TIA.
Sybil
Message Edited by Drummond on 04--2009 05:32 [email protected]

Re: connecting vcr to external SB Audigy 2zs Platinum Pro~ Hi Katman - many thanks for the reply. There is no video connection on the SBA2zs that I can find either. I did send mail to Creative, but they haven't had the courtesy to respond. If I use the 2zs for the audio connection, can I then attach the video connection from the vcr to a separate video capture card? Will this bring everything together and in synch? Sorry, I'm still very much on L plates with all this. Once I get things on to the computer, I can then edit out what I don't want, and burn the rest to cd/dvd; or that's what I'm hoping!! It's getting the data from the vcr tape that's the stumbling block. I know there are?expensi've machines that you can put the vhs tape in and it will copy direct to dvd, my friend has one, but she doesn't know whether you can pause the recording (disk) and let the tape continue running till she gets to the next bit she wants to copy, then start the disk again. TIA of further help.
Sybil
Message Edited by Drummond on 04-3-2009 04:05 AM

Audigy 2ZS Platinum Pro - breakout box not work

I have an an external external breakoput box which was working fine in my old computer. I upgraded the mother board and cpu and installed the Audigy as before. The actual card works but the break out box doesn't light up. If I plug the external box firewire cable in to another firewire port on the computer the power LED lights but that's all. Any ideas anyone?

I am sorry to bump this topic but it is the same as my question and does not seem to have been answered.
I have a Audigy 2ZS Platinum Pro - my old one which I decided to use in lieu of the on-board sound. I installed the latest drivers I could find SBAX_PCDRV_LB_2_18_0017.exe (after unistalling the existing ones)
The card itself works fine but the external interface box is as dead as a doornail. The power for the interface is supposed to come from the two connectors.
No lights no nothing - obviously I have checked the leads and the seating of the card itself. Playback is fine on MP3, midi, wave files etc. I have disabled the on-board sound in the BIOS of course.
Unfortunately the jacks on the back of the card are 1/8 in. outputs only and the external interface provides the inputs which I need for recording etc. They are 1/4in proper ones - guitar lead size which are much better.
I know it is an old card but I like it. The last time I used in in my old computer it was fine. Card/drivers show up in the device manager. I have installed this both on a Win 7 partition and a Win XP partition on my 2 HDDs with the same result. :mansad:
<font color="#0000FF">Any ideas appreciated! Is there something I am doing wrong? Thanks.

Will the external hub of an audigy 2 platinum pro ZS work with an X-fi Xtreme Mus

Topic title says it all.
I recently bought a new pc with a Soundblaster X-fi Xtreme Music, I love the new features of the card however I don't really want to shell out on getting a usb hub.
With my old pc I had a Soundblaster Audigy 2 Platinum Pro ZS (phew that name is long) and it came with a very usefull external hub with midi and audio inputs, the works. I was wondering if it is possible to hook these two up?
Thanks in advance

No, they aren't compatible. The X-Fi card doesn't have any AD_Link connector to link up with the external I/O console you have.
Jason

Audigy 2ZS Platinum Pro - ...trying to record with Videostudio, Virtual VCR, Roxio DVD Builder

...just bought (and installed) a SoundBlaster Audigy 2ZS Platinum Pro - the one with the "breakout box" - to replace the on-board Dell audio sound system, which seems to have died after 4 months.
I am able to get good, clear sound from any and all applications that use "playback" audio.
At present, I can get "playback sound" from one program feature that came with my capture device - an Aver Media USB 300, which was plugged in to the "Line in 2" socket on the break out box. Then I tried to record with it... - "Record Operation Failure!" I'm stilll waiting to see what responses I get from the Aver message board in that regard.
Then I tried recording video (and the accompanying audio) with Ulead Videostudio 8, Virtual VCR, and Roxio DVD Builder, none of which could record sound, even in "preview mode". Before the on board sound system stopped functioning, those features worked on all of the above programs except for Virtual VCR, which I hadn't yet installed or tried out.
I've checked the Play/Record Volume Control in "Accessories/Entertainment" and the Line 2 is activated and selected. I've tried plugging in to Line /Mic but that hasn't worked either. I need to go to Radio Shack to get an adapter to plug in to Line 3 and give that a try.
But before I spend even more money, have you ever seen anything like this?
- Jeff.

Jorge,
Thanks kindly for the suggestion, during the installation it did not complain about this patch being installed allready, I'll give this one more shot and see if it persits.
I ran memtest on the machine (10 cycles) wow this thing (G5) is loud in single user mode. I guess the fans don't have power management enabled.
I'm guessing that the issue is from lack of RAM, (512) but I am not 100% on this. Though my research points towards that, It's kind of odd that an app would reach into some other memory segment.
Thank You Again.
I throught all Tiger updates would be obtainable via "Software Update" . I should have searched support.apple.com first.
Quad G5 Mac OS X (10.4.7) 512MB Ram (Stock Config)

Audigy 2 Platinum Pro remote probl

I was looking over to my Audigy 2 Platinum Pro today and noticed that the remote light is flashing wildly, and I'm not sure why, as I haven't noticed it doing this before. The remote works if you click it, and I even removed the battery to see if the flashing would stop, but still no go. What's the deal?

Tkzoo,
Check your connections to the Audigy card. It may be that the cables aren't all the way in on either side. Is there anything else in the room that might be emitting a IR signal? This could cause the light to blink also.
Jeremy

Audigy 2ZS Platinum Pro in Vista x64: "Skipping" (Distortion) when record

Hi! I've just setup Vista x64 and installed the latest Drivers for my Audigy 2ZS Platinum Pro. Besides the fact that there's no software available for convenient control of the features of my soundcard (Surround Mixer, Speaker Settings, THX Console etc.), everything is fine for playback (after adjusting the bass and treble-sliders to their 0dB-Position!). But I've got a massive problem when recording audio, or when using the microphone: I can play back sound from any source without distortion, but when recording it or using the microphone for VoIP-Applications like Skype, Teamspeak or In-game communication, I get a constant "skipping" distortion like the clicking when a CD is defective and skips.
It sounds like short disruptions which come at regular, very short intervals (approx. 0 per second or so). This effect is always present, irrespective of the load situation of the system and does not change with it. In XP32, my Audigy 2ZS still works like a charme. Furthermore, I've got a "PCI Input Device" in Device Manager with a question mark, although the Firewire-Port does work. Could this be the Gameport not beeing recognised But that's not nearly as problematic as the flaw from above... Thanks in advance for your advice!

I'd like to also add that I have been observing this same problem for quite some time now. While I do not frequently have a need to record, that is changing now and I would rather not have to reboot to Windows XP in order to have functional recording capabilities.
I am currently running a dual-boot configuration of Windows XP/SP2 and Windows Vista Ultimate 64-Bit/SP, with the Audigy 2 ZS Platinum soundcard, and the latest drivers available for the card as of today's date (0/7/2008).
A clip of audio to illustrate the problem may be heard by saving and playing the MP3 file found at http://ambress.com/audigy/audio_recording_fault.mp3. The following graphic also illustrates how the sound is like a series of recorded pulses, making recording completely useless.
I would greatly appreciate any feedback confirming this problem by Creative and what solution is available or when one is to be expected. If a solution is known by any users that perhaps I have missed in searching the forum, of course I'd be grateful for that help as well.
Thank you,
Daryl
Message Edited by Ambress on 10-26-2008 11:43 PM

Audigy 2 Platinum Pro I/O hub Line 3 damaged ?

Hello everybody, I've been using since 2003 an Audigy 2 Platinum Pro but never had the need to use all the inputs of the I/O hub. Now i have and connected an FM Tuner to Line 3 Input. First everything ran fine but the next day i had noise and loud buzz on this input. As i thought that my OS (Win7 Ultimate) was the cause i also installed XP Pro on another partition and just the initial drivers that came with the card years ago but the same behaviour also there in a clean fresh environment without interfering with other drivers or an OS update. So now i must believe that Line 3 is damaged. I connected a VCR over RCA to Line 1 and Line 2. Everything's ok there but Line 3 has noise before connecting and noise and buzz when connecting anything. I also can hear the source but not clearly.
Is there a way to find out if Line 3 is definitely damaged ?
Besides that, is there any restriction in connecting devices over RCA ? I mean can under certain circumstances a damage occur ?
Thanks very much in advance. Happy new year to everybody. Best regards from Germany.

Seems that nobody else has had this problem yet. In the meantime i have found out that just one channel is full of noise. Even under Ubuntu i have this noise so it's definitely the hardware. Must be something damaged indeed. the point is that i would like to know how can i avoid to happen this once again. In the last 25 years i am dealing with RCA Audio i connected the devices always not powering them off before. Seems that the problem is here. It could have shortcutted something inside the I/O box.

Audigy 2 Platinum Pro stutters when decoding from AC3 via ffds

hi all
i am playing a movie with ac3 soundtrack on it.
My Configuration:
Audigy 2 Platinum Pro->AudioHQ->Hardwarecontrol (ger?testeuerung in German)->->Digital Input->Dolby Digital/SPDIF-In-Decoding
->Decoder->use installed Decoder->all settings enabled for Digital EX and DTS ES.
ffdshow->AC3 passthrough to SPDIF and DTS passthrough to SPDIF
I have 6. Analog Speakers connected. (Creative Set)
Problem: Audio stutters like hell !!
Since i also have HTPC (HomeCinema PC) configured with a external decoder, i know the file is ok, and its with all files. on my HTPC i have AC3 Passthrough (SPDIF passthrough if you like) and the decoder (Denon AVR) shows Digital In detected and decodes properly.
Well know to my PCs configuraton where the Audigy should make the decoding. As i play the file, regardless what programm (VLC, Media Player/Classic, InterVideo WinDVD) it shows me the Dolby Digital icon in the lower right screen as i start the movie, so it realizes the Digtial Audio, but why doesnt it decode it properly??

"problem now is, repack decodes all streams as dolby even if its mp3, and very funny, it only works with normal media player, media player classic has no audio anymore".
repack ? I think you mean reclock. mmmh, your problem sounds like a really bad installation, which creates a complete mess in the filter graphs.
Since I'm one who insists on bulding his architectures around generic softwares only (mediaplayer 6.4 and 0 for example), I'll advise you to first uninstall FFDShow, every codecs and parsers installed, and every players too (except the windows integrated ones ) Allways avoid all-in-one solutions if you want a super-flexible and easy to maintain system.
When you've cleaned your system, you can install the codecs and parsers you need for each format. Be aware to configure each one to decode only its format). Avoid the codec pack which are just good to mess what should be a clean installation. Avoid AC3filter, the ac3 decoder from your installed DVD player will be sufficient if it has a good SPDIF option (powerdvd5 audio decoder for example). You might need in some case an XFormer for your ac3 streams http://inmatrix.osnn.net/ac3xform.exe . And don't forget reclock. That's all.
"well, clearly decoding on the PC is far more complex then running it through a external decoder."
Decoding with the PC is complete piece of cake, that's building a good PC with a good system that is not something everything can do with just instinct
"can i control audio buffer in ffd? (id rather be in control then repack, since repack crashes after every movie...)", I don't know, I decided years ago to avoid all-in-one solutions, and on top of all, FFDShow.
" the audigy doesnt do all the work, which is very astonishing and very disapointing..."
What do you mean ? It uses CPU when decoding ? My ZS do not.

Audigy 2 Platinum EX and Windows 7 :'''(

)Audigy 2 Platinum EX and Windows 7 :'''(? Hi to all! I'm new here and my english is so bad..... so excuse me!
With Windows7 (x64 or x84 both!) my Audigy 2 Platinum EX doesn't work correctly!
I've just tried with official driver and update.... last driver are very very bad :'''(
I've partly resolved with unofficial drivers (downloaded on this forum) but external module
still doesn't? work :'''(? i can use only line-in and lin-out, but remote control is completly
unusable.... how can i do? Can you help me, plz?
TXH to all.
P.S.
Excuse me for my english....

)Audigy 2 Platinum EX and Windows 7 :'''(? Hi to all! I'm new here and my english is so bad..... so excuse me!
With Windows7 (x64 or x84 both!) my Audigy 2 Platinum EX doesn't work correctly!
I've just tried with official driver and update.... last driver are very very bad :'''(
I've partly resolved with unofficial drivers (downloaded on this forum) but external module
still doesn't? work :'''(? i can use only line-in and lin-out, but remote control is completly
unusable.... how can i do? Can you help me, plz?
TXH to all.
P.S.
Excuse me for my english....

Rear speakers mapping over front speakers Inspire 5.1 Digital 5500

When I wanted surround on my pc a few years ago, and didn't want to buy a new speaker set, I hooked up my Inspire 5.1 Digital 5500 to my Audigy 2 ZS. The only way to do this was by plugging the different speaker inputs directly from the subwoofer connection panel into the various output ports of my card. Thus skipping the 5500's decoder/volume control device which is only hooked up to provide power to the sub/speaker system. Volumes are set on the audigy card itself.
This has worked fine for a few years and gave no problems whatsoever upto now. Even to the point where I replaced my Audigy 2 for a X-FI Fatality because I thought my soundcard was screwed. With the X-Fi it worked correctly for a day and then it went wrong again. I can't get it to work right and am clueless what the problem is. But I presume it's something in the speaker system.
What happens is as follows:
My rear channels are so soft they almost sound muted. Changing the settings/levels in the speaker settings or THX calibration doesn't make any difference whatsoever. And the majority of the sound that has to go to the back gets mapped on the front speakers. This is also the case with the speaker test and not a dolby/dts/surround problem.
Front Left is ok
Front Right is ok
Front Center gets played by Front Center AND Front Left (soft volume) AND Front Right (soft volume)
Rear Left gets played by mainly FRONT Left (and very softly on Rear Left)
Rear Right gets played by mainly FRONT Right (and very softly on Rear Right)
I rewired, checked cables, (replaced the soundcard from Audigy 2 to X-FI), reinstalled drivers and reinstalled windows. I'm now clueless and got no idea how to get it fixed.
I also tried hooking them up through the optical cable on the X-FI bay and having them properly wired to the 5500's decoder device. But that was even less successfull (only getting a lot of static white noise and no audio signal whatsoever) I also read this won't get me surround anyways except for when true surround sources get played (dvd playback etc), so I stopped going down that path and have them back on the normal minijack plugs.
Please help. I don't want to have to invest in another speaker system. Especially not after the expensive audio card replacement which apparently wasn't necessary.
I also don't get it how a rear signal can end up on the front speakers. When they are seperate cables. Or is there a decoder in the sub-unit as well which may have been broken?
Thanks in advance.
Message Edited by senjin on 04-11-2007 09:50 AM
Message Edited by senjin on 04-11-2007 09:51 AM

I have this exact same issue. I just purchased the X-Fi ExtremeGamer with the Digital I/O Module. I've tried both Coax and Optical, but I get no sound in the rear speakers. 6-Channel Direct works just fine.

Audigy 2 ZS Platinum Pro and Inspire 5.1 Digital 5500

Similar Messages

Maybe you are looking for