Audigy 2 ZS Platinum Pro - spdif and optical at the same t

Hi,
I own a Audigy 2 ZS Platinum Pro, DR release .84.40. I have an optical source and an coax spdif source that I would like to connect to the external module. I have found that as soon as I connect a spdif source the optical is cut off. I can't get it back on until I reboot. Is this as designed? Is the setup capable of taking two spdif and optical input at the same time?Thanks in advance for any help!

I'm no expert but I think he should be fine. Might want to make sure that both the computer and speaker setup are connected to a surge protector (I would recommend one with at least 3000 joule protection). With a good surge protector I don't think he will have any problems...

Similar Messages

Will ATV 3 output from HDMI and Optical at the same time?

I'd like to use my apple TV to feed music to my main AV receiver while at the same time sending that same audio signal out the optical out connection to my other AV receiver that provides music to all of the rooms in my home. Right now it feeds the music to my main AVR via HDMI just fine but nothing to my other AVR.
Is this possible?

We've used an airport express since 'the beginning' - for years to get our Wifi from our cable modem in our garage while simultaneoulsy using it to output audio to a VERY old tuner in the garage. I have some nice outdoor Bose speakers connected to this setup which allows any mobile device wifi equiped to output any audio through my setup.... i.e. we usally use iTunes off our laptop while we are chilling outside. Perfect marriage of new school and old school technology.

How to connect my macbook pro retina and PC to the same monitor(s)?

What's up all - any recommendations here are highly appreciated. I have a gaming PC setup with two (2) DVI out's going to two 24" monitors. One monitor has DVI, HDMI, the other just has DVI. No use in talking VGA here.
I also have a 15" MBP Retina.
Question: What equipment (KVM switch) and setup would allow me to just have my monitors, mouse, keyboard in place and easily switch between my PC and MBP?

a other way is use the T model. connect the two mac with the Thunderbolt cable or FireWire cable
http://support.apple.com/kb/PH10725

How can I setup my MacBook Pro, iMac and MacBook Air the same way without doing each separately? Same home page in Safari, same search preferences, etc

Everytime I buy a new device or whipe out a hard drive and do a fresh install, I have to reset everything. All my preferances, Safari Homepage, passwords, etc.
I know about time machine. The problem is that sometimes, I am trying to avoid a problem that is in the Time Machine's backup.
I spend a lot of time setting my preferences for all the software I use. It is a real pain to modify every toolbar, etc

One thing you can try next time is Setup Migration. So, after downloading and reinstalling OS X and after the restart into Setup use Setup Migration to migrate your user account(s), settings, apps and data from a Time Machine back up.

Audigy 2 Platinum Pro remote probl

I was looking over to my Audigy 2 Platinum Pro today and noticed that the remote light is flashing wildly, and I'm not sure why, as I haven't noticed it doing this before. The remote works if you click it, and I even removed the battery to see if the flashing would stop, but still no go. What's the deal?

Tkzoo,
Check your connections to the Audigy card. It may be that the cables aren't all the way in on either side. Is there anything else in the room that might be emitting a IR signal? This could cause the light to blink also.
Jeremy

Audigy 2 Zs platinum pro - Spdif in Prob

I ' ve got an audigy 2 zs platinum pro card and xbox hooked up to its optical in. Here is my problem:
- At boot up of xbox a stereo signal is coming out of it in dashboard menu. I can hear the sound coming out of the front speakers. When I start a game with dolby digital sound (fifa2005), no sound is heart. I unplug the optical cable and plug it rigth back. It says "dolby digital" on pc' s screen, and dolby digital sound begins (coming out of all speakers)
I guess that audigy accepts the first sound format coming from the optical in ( stereo in this case), and when the signal changes to dolby digital audigy does not recognize it. So when it is unplugged and plugged again, it recognizes that the format is dolby digital.
Is there anyway that Audigy looks to check if the format is same and changes it accordingly?

I have EXACTLY the same proble. There is not only no signal in, I cant hear anything monitored at all when using Cubase or in fact any other sound application. The only sound I can hear is when I plug my speakers/headphones straight into the back of the sound card. I checked my 'Digital Output Only' setting as previously suggested (it wasn't checked) - still no joy.
Somebody please help....

Audigy 2 Platinum Pro stutters when decoding from AC3 via ffds

hi all
i am playing a movie with ac3 soundtrack on it.
My Configuration:
Audigy 2 Platinum Pro->AudioHQ->Hardwarecontrol (ger?testeuerung in German)->->Digital Input->Dolby Digital/SPDIF-In-Decoding
->Decoder->use installed Decoder->all settings enabled for Digital EX and DTS ES.
ffdshow->AC3 passthrough to SPDIF and DTS passthrough to SPDIF
I have 6. Analog Speakers connected. (Creative Set)
Problem: Audio stutters like hell !!
Since i also have HTPC (HomeCinema PC) configured with a external decoder, i know the file is ok, and its with all files. on my HTPC i have AC3 Passthrough (SPDIF passthrough if you like) and the decoder (Denon AVR) shows Digital In detected and decodes properly.
Well know to my PCs configuraton where the Audigy should make the decoding. As i play the file, regardless what programm (VLC, Media Player/Classic, InterVideo WinDVD) it shows me the Dolby Digital icon in the lower right screen as i start the movie, so it realizes the Digtial Audio, but why doesnt it decode it properly??

"problem now is, repack decodes all streams as dolby even if its mp3, and very funny, it only works with normal media player, media player classic has no audio anymore".
repack ? I think you mean reclock. mmmh, your problem sounds like a really bad installation, which creates a complete mess in the filter graphs.
Since I'm one who insists on bulding his architectures around generic softwares only (mediaplayer 6.4 and 0 for example), I'll advise you to first uninstall FFDShow, every codecs and parsers installed, and every players too (except the windows integrated ones ) Allways avoid all-in-one solutions if you want a super-flexible and easy to maintain system.
When you've cleaned your system, you can install the codecs and parsers you need for each format. Be aware to configure each one to decode only its format). Avoid the codec pack which are just good to mess what should be a clean installation. Avoid AC3filter, the ac3 decoder from your installed DVD player will be sufficient if it has a good SPDIF option (powerdvd5 audio decoder for example). You might need in some case an XFormer for your ac3 streams http://inmatrix.osnn.net/ac3xform.exe . And don't forget reclock. That's all.
"well, clearly decoding on the PC is far more complex then running it through a external decoder."
Decoding with the PC is complete piece of cake, that's building a good PC with a good system that is not something everything can do with just instinct
"can i control audio buffer in ffd? (id rather be in control then repack, since repack crashes after every movie...)", I don't know, I decided years ago to avoid all-in-one solutions, and on top of all, FFDShow.
" the audigy doesnt do all the work, which is very astonishing and very disapointing..."
What do you mean ? It uses CPU when decoding ? My ZS do not.

Audigy 4 platinum pro Microphone im

Simple one here, i'm just about to buy some leads to connect my condensor mic to my external hub. I just bought a preamp, yet don't have all the leads for it to work. Will a 'balanced /4" TRS connector' fit into the 'Mic imput'/'line-in' of my Audigy 4 platinum pro soundcard? This is opposed to an 'Unbalanced /4" TS connector'. Help will be appreciated! Carry on being CREATIVE
P3U6!SUn 3H+

Hi there,
I nearly freaked out when I got the platinum pro as I thought I could get no decent power in direct guitar and microphones. You said you bought a preamp, but there is a preamp switch for Line In/Mic on the front of the hub. I have been using this for boosting mic and guitar signals and it is okay but was wandering what preamp you bought and if you rate it.
Hope I haven't upset you by telling you about the built in pre-amp as it probably isn't the best quality anyway.
Cheers,
Paul D.

Connecting vcr to external SB Audigy 2zs Platinum Pro

I've just joined, so apologies if I "mess up". I have some precious things on vhs tape, and want to transfer them to cd/dvd. I run Windows XP. I have to use rca connections, don't think there's another option on the vcr. I see the red and white rca connections on the back of the external 2zs, but where does the yellow (video) connection go? Would be very grateful for help. TIA.
Sybil
Message Edited by Drummond on 04--2009 05:32 [email protected]

Re: connecting vcr to external SB Audigy 2zs Platinum Pro~ Hi Katman - many thanks for the reply. There is no video connection on the SBA2zs that I can find either. I did send mail to Creative, but they haven't had the courtesy to respond. If I use the 2zs for the audio connection, can I then attach the video connection from the vcr to a separate video capture card? Will this bring everything together and in synch? Sorry, I'm still very much on L plates with all this. Once I get things on to the computer, I can then edit out what I don't want, and burn the rest to cd/dvd; or that's what I'm hoping!! It's getting the data from the vcr tape that's the stumbling block. I know there are?expensi've machines that you can put the vhs tape in and it will copy direct to dvd, my friend has one, but she doesn't know whether you can pause the recording (disk) and let the tape continue running till she gets to the next bit she wants to copy, then start the disk again. TIA of further help.
Sybil
Message Edited by Drummond on 04-3-2009 04:05 AM

Audigy 2ZS Platinum Pro - breakout box not work

I have an an external external breakoput box which was working fine in my old computer. I upgraded the mother board and cpu and installed the Audigy as before. The actual card works but the break out box doesn't light up. If I plug the external box firewire cable in to another firewire port on the computer the power LED lights but that's all. Any ideas anyone?

I am sorry to bump this topic but it is the same as my question and does not seem to have been answered.
I have a Audigy 2ZS Platinum Pro - my old one which I decided to use in lieu of the on-board sound. I installed the latest drivers I could find SBAX_PCDRV_LB_2_18_0017.exe (after unistalling the existing ones)
The card itself works fine but the external interface box is as dead as a doornail. The power for the interface is supposed to come from the two connectors.
No lights no nothing - obviously I have checked the leads and the seating of the card itself. Playback is fine on MP3, midi, wave files etc. I have disabled the on-board sound in the BIOS of course.
Unfortunately the jacks on the back of the card are 1/8 in. outputs only and the external interface provides the inputs which I need for recording etc. They are 1/4in proper ones - guitar lead size which are much better.
I know it is an old card but I like it. The last time I used in in my old computer it was fine. Card/drivers show up in the device manager. I have installed this both on a Win 7 partition and a Win XP partition on my 2 HDDs with the same result. :mansad:
<font color="#0000FF">Any ideas appreciated! Is there something I am doing wrong? Thanks.

Will the external hub of an audigy 2 platinum pro ZS work with an X-fi Xtreme Mus

Topic title says it all.
I recently bought a new pc with a Soundblaster X-fi Xtreme Music, I love the new features of the card however I don't really want to shell out on getting a usb hub.
With my old pc I had a Soundblaster Audigy 2 Platinum Pro ZS (phew that name is long) and it came with a very usefull external hub with midi and audio inputs, the works. I was wondering if it is possible to hook these two up?
Thanks in advance

No, they aren't compatible. The X-Fi card doesn't have any AD_Link connector to link up with the external I/O console you have.
Jason

Audigy 2ZS Platinum Pro - ...trying to record with Videostudio, Virtual VCR, Roxio DVD Builder

...just bought (and installed) a SoundBlaster Audigy 2ZS Platinum Pro - the one with the "breakout box" - to replace the on-board Dell audio sound system, which seems to have died after 4 months.
I am able to get good, clear sound from any and all applications that use "playback" audio.
At present, I can get "playback sound" from one program feature that came with my capture device - an Aver Media USB 300, which was plugged in to the "Line in 2" socket on the break out box. Then I tried to record with it... - "Record Operation Failure!" I'm stilll waiting to see what responses I get from the Aver message board in that regard.
Then I tried recording video (and the accompanying audio) with Ulead Videostudio 8, Virtual VCR, and Roxio DVD Builder, none of which could record sound, even in "preview mode". Before the on board sound system stopped functioning, those features worked on all of the above programs except for Virtual VCR, which I hadn't yet installed or tried out.
I've checked the Play/Record Volume Control in "Accessories/Entertainment" and the Line 2 is activated and selected. I've tried plugging in to Line /Mic but that hasn't worked either. I need to go to Radio Shack to get an adapter to plug in to Line 3 and give that a try.
But before I spend even more money, have you ever seen anything like this?
- Jeff.

Jorge,
Thanks kindly for the suggestion, during the installation it did not complain about this patch being installed allready, I'll give this one more shot and see if it persits.
I ran memtest on the machine (10 cycles) wow this thing (G5) is loud in single user mode. I guess the fans don't have power management enabled.
I'm guessing that the issue is from lack of RAM, (512) but I am not 100% on this. Though my research points towards that, It's kind of odd that an app would reach into some other memory segment.
Thank You Again.
I throught all Tiger updates would be obtainable via "Software Update" . I should have searched support.apple.com first.
Quad G5 Mac OS X (10.4.7) 512MB Ram (Stock Config)

Audigy 2ZS Platinum Pro in Vista x64: "Skipping" (Distortion) when record

Hi! I've just setup Vista x64 and installed the latest Drivers for my Audigy 2ZS Platinum Pro. Besides the fact that there's no software available for convenient control of the features of my soundcard (Surround Mixer, Speaker Settings, THX Console etc.), everything is fine for playback (after adjusting the bass and treble-sliders to their 0dB-Position!). But I've got a massive problem when recording audio, or when using the microphone: I can play back sound from any source without distortion, but when recording it or using the microphone for VoIP-Applications like Skype, Teamspeak or In-game communication, I get a constant "skipping" distortion like the clicking when a CD is defective and skips.
It sounds like short disruptions which come at regular, very short intervals (approx. 0 per second or so). This effect is always present, irrespective of the load situation of the system and does not change with it. In XP32, my Audigy 2ZS still works like a charme. Furthermore, I've got a "PCI Input Device" in Device Manager with a question mark, although the Firewire-Port does work. Could this be the Gameport not beeing recognised But that's not nearly as problematic as the flaw from above... Thanks in advance for your advice!

I'd like to also add that I have been observing this same problem for quite some time now. While I do not frequently have a need to record, that is changing now and I would rather not have to reboot to Windows XP in order to have functional recording capabilities.
I am currently running a dual-boot configuration of Windows XP/SP2 and Windows Vista Ultimate 64-Bit/SP, with the Audigy 2 ZS Platinum soundcard, and the latest drivers available for the card as of today's date (0/7/2008).
A clip of audio to illustrate the problem may be heard by saving and playing the MP3 file found at http://ambress.com/audigy/audio_recording_fault.mp3. The following graphic also illustrates how the sound is like a series of recorded pulses, making recording completely useless.
I would greatly appreciate any feedback confirming this problem by Creative and what solution is available or when one is to be expected. If a solution is known by any users that perhaps I have missed in searching the forum, of course I'd be grateful for that help as well.
Thank you,
Daryl
Message Edited by Ambress on 10-26-2008 11:43 PM

Audigy 2 Platinum Pro I/O hub Line 3 damaged ?

Hello everybody, I've been using since 2003 an Audigy 2 Platinum Pro but never had the need to use all the inputs of the I/O hub. Now i have and connected an FM Tuner to Line 3 Input. First everything ran fine but the next day i had noise and loud buzz on this input. As i thought that my OS (Win7 Ultimate) was the cause i also installed XP Pro on another partition and just the initial drivers that came with the card years ago but the same behaviour also there in a clean fresh environment without interfering with other drivers or an OS update. So now i must believe that Line 3 is damaged. I connected a VCR over RCA to Line 1 and Line 2. Everything's ok there but Line 3 has noise before connecting and noise and buzz when connecting anything. I also can hear the source but not clearly.
Is there a way to find out if Line 3 is definitely damaged ?
Besides that, is there any restriction in connecting devices over RCA ? I mean can under certain circumstances a damage occur ?
Thanks very much in advance. Happy new year to everybody. Best regards from Germany.

Seems that nobody else has had this problem yet. In the meantime i have found out that just one channel is full of noise. Even under Ubuntu i have this noise so it's definitely the hardware. Must be something damaged indeed. the point is that i would like to know how can i avoid to happen this once again. In the last 25 years i am dealing with RCA Audio i connected the devices always not powering them off before. Seems that the problem is here. It could have shortcutted something inside the I/O box.

I downloaded and bought a movie from iTunes on my iPad and now want the same movie on my MacBook Pro but its not offering me to download it, it giving me the options of buying it which I already did. How I get the movie onto my MacBook?

I downloaded and bought a movie from iTunes on my iPad and now want the same movie on my MacBook Pro but its not offering me to download it, it giving me the options of buying it which I already did. How I get the movie onto my MacBook?

You can connect the iPad to your Mac's iTunes and do File > Devices > Transfer Purchases, that should copy it over to the Movies part of your library.
Depending upon what country that you are in, and whether the film studio allows it, you might also be able to re-download it on your Mac via the Purchased link under Quicklinks on the right-hand side of the iTunes store home page.

Audigy 2 ZS Platinum Pro - spdif and optical at the same t

Similar Messages

Maybe you are looking for