Audigy 2 ZS Pro digital output and Windows XP Pro

Recently "upgraded" my system to Windows XP Pro X64. My soundcard, an Audigy 2 ZS Pro, connects to my logitech 5. digital speakers via the front coaxial connector, no longer seems to output digital signal. The speakers indicate that there is no signal from the coaxial connection. I can hear sound from headphone through the analog output though.
Before the upgrade, I had everything working, but I don't remember all the details I went through to get it to work.
I have installed latest driver for Windows XP X64 from Creative, and I have modified the setting to bypass onboard decoding. Is there anything else I need to do? Online documentation talks about applications that I don't seem to have. Is there a X64-compatible application I need to run to get this to work? Thanks.
George

Okay Robert, I downloaded and installed your 6.25 drivers and they work fine. However, the Audigy 4 pro software, http://files.filefront.com/Pax+Audig.../fileinfo.html, does not install anything but drivers, no software applications. I looked on your board and could not find any definati've method for resolving this problem.
Perhaps you or someone else who is familiar with installing the software apps would care to provide a detailed solution.

Similar Messages

Can I disable 'digital output' and switch to internal speakers only?

Last month, a jack from a headphone broke off and got stuck in the audio input of my Macbook Pro.
They were able to get the broken peace out, but I think they damaged something in the input by pulling it out.
When I press the volume buttons I get this sign:
https://www.google.be/search?q=no+sound+mac&espv=210&es_sm=91&source=lnms&tbm=is ch&sa=X&ei=Ldr0UtnzNcb8ygPwwIHgAw&ved=0CAkQ_AUoAQ&biw=1020&bih=546#facrc=_&imgdi i=_&imgrc=o0nxcZoiz0kGUM%253A%3Bbd1IQ1bSgYnzxM%3Bhttp%253A%252F%252Fi54.tinypic. com%252Fop1amf.png%3Bhttp%253A%252F%252Fwww.mac-forums.com%252Fforums%252Fos-x-o perating-system%252F253164-no-sound-after-upgrading-itunes.html%3B211%3B205
When I go to audio preferences I only see 'Digital Output' as an option. (not 'internal speakers')
The Macbook still thinks there's a jack inside.
Is there a way to switch on to Internal Speakers (because they DO work, but I cant enable them) by disabling the Digital Output?

Are you seeing a red light at the port? It can get stuck so that it still thinks the headphones are plugged in. Try taking another headphone jack and plugging it in a few times.

Unable to install Adobe Digital Editions and Windows 8

help - I keep trying to install Adobe Digital Editions on Windows 8 - icon appears; program is in "programs" but ADE isn't there - I've installed, uninstalled several times - and still not up and running - need help- is ADE not compatible with Windows 8?

Moved to ADE forum.

Problem with digital output and microph

Hello! I recently bought a new motherboard MSI K8N SLI Platinum that have onboard Sounblaster Li've 24bit, with coaxial and spdif and also the standard outputs. I ve connected via a fiber optical cable to my amplifier and i checked the digital output only box to the advanced settings on the mixer. I am hearing sound very well from my amplifier but when i connect headphones to with microphone to my soundcard , i don't hear anything at all from my headphones. Also i cannot speak via microphone. If i uncheck the box digital output only i hear sound from my headphones and also i can speak to microphone. Is there some way to have them both enabled? In my previous motherboard i didn't have that problem. I could hear sound from my amplifier with pcm signal and from my headphones and microphone analog at the same time.
Thanks!

Thibaud,
The clue is here: " i take acquisition with one sample on demand."
You are apparently using software timed output. To maintain accurate phasing at 80 Hz you need timing which is accurate to better than 4 milliseconds. This is not likely to occur with a desktop operating system. Sometimes it will be good and other times OS latencies will throw the timing way off.
If your board supports it, use hardware timing. The timebase sources on most boards are far more precise and accurate than software timing.
Lynn

5th media live with no digital output, and now pci slot is dead

you may recall my previous thread, where my 4th media live, still had no spif digital output. well i sent it back to ebuyer and got another one, and low and behold the same, only this one is noisyer and the pci slot seems to be dead!
i have tried a couple of devices in the riser card, and non of them seem to be recognised?
anyone got any ideas.
cheers
john

OK Status update:
I posted this question on the Dutch forum as well. I am happy to tell you all that in the Dutch forum Dragonfly is one of the moderators. He knows his MSI stuff
He gave me the solution to my problem. So just in case anyone else has a similar problem and can't read Dutch, here it is
He advised me to start the Media Live up with no monitor or TV attached to it at all. Then start up with either a monitor or a TV attached to it. Lo and behold.... the problem is solved.
All credits for this solution go to Dragonfly
Greetz,
J@n
PS Mark topic as SOLVED

Digital@nywhere and Windows 7

Hello all,
I have been using my Digital@nywhere card for a few years now, with no problems. However, as I upgraded my OS to Windows 7, after reinstalling the drivers and the software, the software does not run. Whenever I click on the TVR button, I get an error that says this: Access violation at address 0002111D in module 'kwusbdll.dll'. Read of address 0000000. And then I will have to close the program in the taskbar. I have tried to run the software in the compatibility mode of Windows XP to no success. I have also tried to reinstall the program using the setup found here: http://eu.msi.com/index.php?func=downloaddetail&type=driver&maincat_no=132&prod_no=642 but the problem is still there. Is there a way to fix this problem, or perhaps another DTVR application I can use?

Yes and yes.
I tried that program in the sticky, ScanChannelsBDA_UK, and when I choose my country (Australia) I get this error saying it failed to connect filters to graph. Here is the log if it helps:
Build - v2.8.1.0
Checking for new BDA DVB-T Cards
Tuner - Xpert BDA DVB-T Tuner/Demod
@device:pnp:\\?\stream#cxbdatune.ven_14f1.samsungdvbt#5&29d22fe9&4&1#{71985f48-1ca1-11d3-9cc8-00c04f7971e0}\{91b0cc87-9905-4d65-a0d1-5861c6f22cbf}
Finding Demod and Capture filters
Trying - Conexant 2388x Transport Stream Capture
@device:pnp:\\?\pci#ven_14f1&dev_8802&subsys_86231462&rev_05#4&23c0b1c&0&52f0#{fd0a5af4-b41d-11d2-9c95-00c04f7971e0}\global
Finished Finding Demod and Capture filters
Finished Checking for new BDA DVB-T Cards
Found BDA device: Xpert BDA DVB-T Tuner/Demod
Failed to connect Capture filter to BDA Demux
Failed to connect filters in graph.
Failed to connect Capture filter to BDA Demux
Failed to connect filters in graph.
Failed to connect Capture filter to BDA Demux
Failed to connect filters in graph.
Failed to connect Capture filter to BDA Demux
Failed to connect filters in graph.

Synchronize digital output AND digital input NI-USB 6343

Hello
I'm using NI-USB 6343 to drive 1 TTL device. This device can also output a TTL signal to indicate whether the gate is opened/closed.
I'm using Digital Bool 1 Line 1 Point. I was able to flip gate open/close in timely manner. But i Like to sync DI and DO properly.
I tried to throw in OnBoard clock but it was not successful.
Is there any way to sync DI and DOI using onbaord/hardware clock?
Any insight will be great!
Thanks!!

Hi,
Synchronizing your DI and DO tasks should be possible with your device. You will need to time them off of a a clock that is usable by both. This information is available in the X Series User Manual
http://www.ni.com/pdf/manuals/370784f.pdf
pg 6-9 and 6-13
You can also find some information and examples of syncing various tasks in the article below.
http://www.ni.com/product-documentation/4322/en/
Best of luck,
Eric

Is there a solution for Digital Persona and Windows 10 and Edge or Google

I upgarded to windows 10 and now my digital persona does not work. Is there a solution for Microsoft Edge? If not is there a solution for google? I can make google my defult browser but it does not work there either?

We upgraded one laptop at home and I wasn't very surprised to find out that the backup / imaging program we were using on Windows 7 (Backup Exec System Recovery) stopped working. It's a nice program that I've been using for years - creates a base image then incrementals on a schedule. Allows for simple full bare metal recovery or for file recovery by mounting an image inside the program.
Have any of you tested anything similar in Windows 10?
This topic first appeared in the Spiceworks Community

Need help with waveform and digital output

Hey everyone,
I am driving a rotational motor with an example waveform output VI and an example digital output VI. I am able to successfully send a square wave with the desired properties to rotate the motor and I am also able to successfully send a digital output (1 or 0) to change its direction (clockwise/couter-clockwise.
However I need some advices to write a setup such that after the motor runs as desired, I can return the motor back to its original position. I think the simplest way is timing how long it takes to finish its task, and just change the digital output, keep the same wave properties and run for the same amount of time.
So how can I time how long the program runs and with some kind of button, change the digital output and run the program again?

As more of a program architecture tip, this sounds like a great time to be using a State Machine. I say this because you mention resetting the motor (one state) then running it again (another state) repeatedly. As a design tip, I would check out this article, along with the Design Pattern Template that comes with LabVIEW. You can find this by going to File >> New... then expanding the tree to VI >> From Template >> Frameworks >> Design Patterns >> Standard State Machine.
Cheers,
Brian A.
National Instruments
Applications Engineer

Error -200279 with simultaneous analog input (different devices) and digital output.

Hi guys,
I am a beginner in Labview and have been dealing with this problem for a couple of weeks now and just can't seem to get it completely right, I have a feeling there are a few small bugs in my code/hardware setup.
I am running an scxi-1000 chassis with a 1600 module and 1302C along with a 1303 accesory for temperature measurements, this is connected to four thermoucouples. Unfortunately I have a limited number of modules available so I am also using a PCI-6221 DAQ card with an scb-68 breakout box used for a digital output and analog input voltage channel. Attached is my labview program. When I run the code at a 50 Hz sampling rate it runs with no errors but the data file comes out extremely wrong, this is also attached. When I run the code at 100 Hz I get error-200279 after a few loops. I used to have 2 daqmx timing VIs (one for each input), but the same error would eventually happen, I have also tried increasing the buffer size on said timing VI. I am also using an old computer (Pentium IV) could this effect the program?
I have learned a lot going through forms for similar problems to mine but I just can't get it to for an extended period of time, I have posted my simplest code.
Thanks in advance,
Luca
Attachments:
tc_2.txt ‏1102 KB
FinalCombined_2.vi ‏128 KB

Ok this makes sense. I have made the suggested modifications but still getting the same error with sampling rates of 100 Hz or higher. Could you check that I have implemented the queue VIs properly (new file attached)? Also when running at 50 Hz in debug mode it does not look like the second while loop (with the dequeue element) comes into play until I hit the stop button, once I hit the stop button I get the following error:
Error 1 occurred at Dequeue Element in FinalCombined_2.vi
Possible reason(s):
LabVIEW: An input parameter is invalid. For example if the input is a path, the path might contain a character not allowed by the OS such as ? or @.
=========================
NI-488: Command requires GPIB Controller to be Controller-In-Charge.
This leads me to believe I have programmed the queue elements incorrectly.
Thanks for your help, any suggestions are greatly appreciated.
Luca
Attachments:
FinalCombined_2.vi ‏102 KB

No digital output sound

For several years, I've used the TOSlink output to a cable to a digital input on my stereo system.
Now I am getting no sound from the stereo from the computer. I've recently moved things, like devices and wires, so I may have something connected badly.
I get sound when I choose the built-in speakers, or when I connect tiny speakers to the headphone jack.
I disconnected the headphone line, tried two different digital cable from the digital output on on the back of the Mac Pro (the outlet with the red light) to the optical input on the receiver. I can listen to the radio from the receiver, but when I select digital input on the receiver and digital output in the Sound panel of system preferences, I get no sound.
Any suggestions?
Thanks,
Phil

Yo, BadBoy! Phew! Man, you helped me out a bunch. I had to do some tinkerin' between the drivers from Gateway and the Li'veDrvUni-Pack. I had to install it without the windows drivers from Li'veDrv... and start clean. I'm now getting digital output and my mic is working on my old card. I can't get the Creative Surround Mixer from my old card's software, or from Li'veDrv.. but I can use Windows' Volume Control. If you want to see why sound is so important to me ya' can check out my site at http://www.ramseybotelho.com. Thanks again, Dude.

No digital output from 6 year old Sound Blaster C

Hey Everyone, I'm new to this board and have a question. I recently purchased a custom-built computer with an ASRock PCI Express motherboard with
onboard speaker and mic inputs. I have Boston Acoustic BA735 digtal speakers. I can only get
analog from the onboard sound. I removed and installed my 6 year old Sound Blaster Li've
Value card (Model # M48309403265) from my old Gateway PC into my new one, and installed
the Li'veDrvUni-Pack update for Windows XP. I can't get any digital or analog output from the
card. I tried my mic on the onboard input, but kept getting pulses at regular intervals on
my WAVforms or sonographs. I plugged the mic into my old Sound Blaster card and the pulses
disappeared, so I know the mic is working. With all the info I've provided, is there a patch
or update or anything for my old Sound Blaster Li've card to get digital output?
I tried the Sound Blaster Li've 24 Bit card, but returned it because the same input for the
speakers is the same for the mic. Also, there's no gameport on it.

Yo, BadBoy! Phew! Man, you helped me out a bunch. I had to do some tinkerin' between the drivers from Gateway and the Li'veDrvUni-Pack. I had to install it without the windows drivers from Li'veDrv... and start clean. I'm now getting digital output and my mic is working on my old card. I can't get the Creative Surround Mixer from my old card's software, or from Li'veDrv.. but I can use Windows' Volume Control. If you want to see why sound is so important to me ya' can check out my site at http://www.ramseybotelho.com. Thanks again, Dude.

Use of digital connection and Headphones - is it possibl

I am extremely happy as I have found that by using the "Flexijack" configured as a digital output and connecting it to my Logitech speakers I have resolved a problem that had developed with my front speakers going missing.
BUT when I try and use my headset for Skype I get distorted sound. Without the earphones connected the sound is perfect through the speakers. Is there a configuration I can use or I am expecting too much of the system ?
I have an OEM version of the X-Fi supplied as part of a Dell Dimension 950
Thanks in advance
Steve

It really runs with APDU buffer of usual Java Cards! Of course it works with the APDU buffer: it's a global array.
But SIM cards haven't such global array. Does it mean
that this scenario will not run there?Yes, it won't. As the APDU buffer is a global array (what implies that it is also a temporary JCRE entry point object), you're not able to store the reference in a class attribute or instance variable. So it's not useable for a Toolkit Applet which has been triggerd by an event.
A work around would be to pass each single primitive data unit to the Shareable Interface Object. But don't ask for performance ;o)

PWM output and DIO output on same pin(MultiTasking)

Hi guys, ive encounter some problem in myrio 1900, which is using PIN31 for digital output and PWM output. while the testing , i cant sending PWM, i only can passing the read value from other Digital input and transfer towards PIN 31. ive tried to change in low level logic but myrio disconnect after 3-5 seconds. By the way ive attached few picture to clarify my current situation, hope can clarify my problem clearly.
thank you.
regards
vincent
Attachments:
1.png ‏51 KB
2.png ‏49 KB
3.png ‏49 KB

http://forums.ni.com/t5/Academic-Hardware-Products-ELVIS/bd-p/10

Simultaenous digital out and analog in

Hi. I am running into an issue with the simultaneous AI (analog in) and DO (digital out) with Athena (www.diamondsystems.com) and LabVIEW (see the supplied files): The original program example supplied by somebody (the attached 060126 file) runs fine with these two simultaneous operations.
However, for my specific requirements, I would have to put a frame (flat sequence) around the DO part (the attached 060131 file), followed by another flat sequence frame that changes another DO state. The reason that I must do this is that I have 2 valves which change states as the AI operation continuous to run.
I have noticed though, once I put those flat sequence frames around it, the DO pauses and doesn't perform the operation until the AI loop is stopped. I have tried to create various local variables but the issue persists. Would there be a workaround for this? Thanks.
Attachments:
HMIR_SBC_060131.vi ‏374 KB
HMIR_SBC_060126.vi ‏137 KB

I have taken a look at your code. Based upon your description,
and the fact that I do not have the driver for your device, I am not exactly
sure where the program is pausing. I can give you some suggestions to
resolve your problem. When you use a flat sequence structure, every piece
of code in a frame has to finish execution before the next frame will start
execution. If you have code in parallel (i.e. digital output and analog
input) in one frame and the same in a second frame the digital output and analog
output in the second frame will not start until all the code in the first frame
has finished execution. In your case it you have a while loops for
digital input and output in the first frame. When both of these loops
finish execution, you should see the second frame start shortly after.
From your description what I believe is happening is that the digital output in
the first frame is finishing and waiting for the analog input to finish.
After the analog input loop finishes the second frame can start. If you
want the second frame's digital output to start before the loop finishes
execution you will need to take that code out of the frame.
Regards,
Jesse O
Applications Engineering
National Instruments
Jesse O. | National Instruments R&D

Audigy 2 ZS Pro digital output and Windows XP Pro

Similar Messages

Maybe you are looking for