Audigy Audio Extention Connec

Hi, its me again!:smileytongue:
In Audigy 2 card, you know that Audio Extension connector?
Anyone knows which pin(s) are for headphones?
reason: i had on board sound and the pc case has "font pannel earphone jacks-which i connected to motherboard".
But now with Audigy2, my earphones would not reach all the way to the back of the pc.
ALthough I mostly use my 5. speakers, sometimes i wanna use earphones...but .trouble unplugging and plugging everytime i want to do this....2.earphone too short for this...
So, if anyone knew which pins were for earphone I could hook up the pc case connector there....no? yes?
Lauren,
thank you in advance for your help!

google --> pin headphone "audigy 2"
after 2 minutes:
http://www.driverheaven.net/showthre...79&page=3&pp=5
hope that hel
ps.

Similar Messages

SB Audigy Audio [9400] Drv

I cannot find drivers for my SB sound card, i've tryed every driver on the download page and they all say 'Setup could not detect any sound blaster audio card on your system, please ensure you SB hardware is properly installed'

Try going to the Audigy control panel and make sure the effects settings are turned off as well as the advanced controls for the Windows volume control. If that doesn't fix it then you may need a new sound board.

Audigy audio card with

Hi,For a project we have a requirement to check presence of audio and validate with appropriate reference provided. Is audigy 2 or audigy 4 provides any sdk to satisfy these needs ?. Please let me know about this.

I doubt there are a spesific SDK for Audigy or any other model available. There is a program called CTHelper.exe installed/running, which purpose is to aid 3rd party developers create plugins/software for the card but, can you find a SDK for it ....
You should contact Creative directly on this matter of yours.
kX Project drivers do have a SDK for their SB drivers.
- http://www.driverheaven.net/kx-project-audio-driver-support-forum/
jutapa

SB Audigy Audio B

hi,?I've bought my computer a few years ago from someone and there was a sound cart with it. A week ago I bought a Zalman ZM-RS6F+M headset. http://www.zalman.co.kr/eng/product/...dx=34&code=023. It's a headset with 5. sound. I plugged my headset in the . I can hear left and right, but I'm not sure if I hear front and rear. I don't know where I have to plug in. The?inputs on my card?have a different color then the ones of my Zalman headset. The inputs of the sound card are left, right etc. But the plug-ins of my headset are front, rear and center.And there is another thing i don't know. I don't know if I should change the speaker settings in my audio console. I changed them in windows, but do i have to change that in de audio console too? Should?I click on Synchronize with Microsoft Windows Control Panel?If someone can?help me with my settings and stuff so I can listen 5. sound with my headset, please.

According to what I see here.
http://www.zalman.co.kr/product/audio/theatre6_0.html
The audio cable from your headset is as follow:
Front->Light Gray color
Rear->Dark Gray color
Center->Black color
Assuming you're using the old Audigy soundcard, so the front audio cable from the headset should go to Line_Out(LIN_OUT) from the soundcard, rear to Line_Out2(LIN_OUT2) and Center to Digital Out jack. If you're unsure of the jack description on the soundcard, you can download the manual guide from the link below.
http://asia.creative.com/support/dow...Blaster+Audigy
Jason

Quake 4 Will not start with USB Audigy 2 NX Connec

Anyone playing Quake 4 successfully with the USB Audigy 2 NX installed? Will there be a driver update so this game will play? Activision was no help. When I disconnect mine I can play the game fine... other than no sound.
How about a driver update Creative?

I got the same problem. The issue is that Quake4 launches with OpenAL enabled by default and causes the game to quit to the desktop. Try disabling the card and launch Q4 and you will see it works with no sound. ALot of people are using default sound card drivers or onboard sound to fix the issue until a patch. I found if you install OpenAL or Creative beta OpenAL drivers work but cause issues in game with stutter or cracking. Im still on the hunt for a issue since now I cant load my Creative control panel since I loaded the beta OpenAL drivers. Hope this helps

Sb Audigy Audio [B800] problem

I have bought an Inspire GD580 5. with an external Dolby Digital/DTS decoder box for my computer (and my playstation 2). When I plugged it to my computer I noticed that the only sound that was coming out was from the left and the right speaker and nothing else. I have read the online manual which states that I have to enable the AC3 encoder box located in the Surround Mixer under the speaker settings in order for the card to let the signal pass through the card in order to allow my external Decoder box to decode the signal. But when I followed what it said I found the AC3 encoder box knoware to be found! PLease help me.

Eddy,
Which drivers are you running on the system now? It may be that the location has moved if you are using newer drivers. If you are running the new EAX 4.0 drivers, you can change the decoder setting from a program call CTpanel.exe. It is usually found in this location (with the newest drivers installed): c:\program files\creative\sb audigy\program\wdm\common and the file in there (I also added it to my desktop later as I love this config program). There should be a decoder tab that will allow you to disable the onboard decoder for SPDIF bypass. If you don't have this I would suggest installing the updated drivers (first the Audigy Web Drivers and then the EAX 4.0 update).
Jeremy

SB Audigy Audio Softwa

I have a gateway computer, but I don't have any software.
Like I don't have any programs to change my sound settings.
Where do I get the software?
I wanna use my headphones, but I have no options anywhere to choose to use a headphone setting.
Please help!
Thank you.

If the card came with the computer, have you tried asking Gateway for the software? If you added the card, the software should have come with it. If you bought a retail boxed version, you go to Creative to get the missing software. If you bought an "oem" version (a so-called "grey market" card), it should have come with a software CD but that is the responsibility of the seller, so if it's missing you should ask the seller why you didn't get one.
-Dave
[email protected]

Sb audigy audio c

hey guys,
i got a question..i currently use a head set for voice chats but for some reason the playback of ppl talking comes out of my speakers is there any reason for it's i want it to come out of my headset but its not working. should i have my settings in a particular type?

If its a usb headset then you in essence have 2 soundcards, could you not mute your speakers whilst using your headset ?
If it isn't usb then tell us what stuff you have, its better to give to much info than not enough

Win XP finds no audio device after installing Audigy 2

After installing Audigy 2 ZS, my Windows XP could no longer identify an audio device. Under Control Panel > Sounds and Audio Devices, clicking on the Audio tab, there is no Default Device for playback or whatsoever.
However, under the Hardware tab, Audigy 2 ZS is visible and seems to work fine. The only suspicious part I caught is that when I check for Properties of Audigy 2 ZS and go down to check Properties of Creative Audigy Audio Processor (WDM), the status shows "The di'ver is enabled but has not been started." I have no idea how this can be fixed.
The integrated sound card is turned off in the BIOS.
I've tried all possible ways to install, uninstall, install..., but just couldn't get XP to work properly. Any other possible solutions out there?
Many thanks!

Solved after reinstalling Win XP. Wasted too much time on trying other possible solutions.
Hope other people may learn something out of it.

Midi/audio sync prob after sblive to audigy 2zs upgrade

Have posted the following earlier today in Soundblaster forum - then thought it may be better off here.....
Hi all - have just had to quickly buy new soundcard as main line-out on sblive gave up the ghost, after years of no probs. Bought Audigy 2zs, as thought this would not be too much of a shock for ageing AMDk6 450mhz running Win98se. (Am waiting for new pc music system.) Installed Audigy, using 1xm1n's excellent set-up guide, and thought everything was ok. However, when running sequencer, the midi tracks are fine, while the audio slowly goes out of sync. Can anybody explain what's happening? Would not normally panic, and wait for new pc, but have a deadline to finish project for the Barmy Army !!
Seriously thinking of reinstalling sblive, and using the rear line-outs to monitor on - but line-in & mic will then not work. Also was hoping the Audigy ASIO drivers would let me do the final mix in Cubase.
Did I mention the odd crackle & pop....? .....Aaaaaaargh!!
Regards.

Jason,
Yes I tried pulling card. What has happened.
. Card was "re-found" by windows for no reason which started the problems.
2. I deleted driver in control panel, shutdown and pulled card, rebooted again with no card.
3. Put the card back and rebooted again and at that point it showed as Audigy ZS, although it did not look like all functionality was there as before.
4. So I installed the new January 06 drivers. Seemed to go okay.
5. Upon reboot, came up as Creative Audigy Audio Processor" again. However things "worked" for a while. The mixer came up, etc.
6. Seemed to be working, then stopped working (no sound)....and upon a reboot, was re-found again and was using old generic drivers from 2003. And was no longer called a ZS.
7. EDIT: Important, in the "sound and audio" devices in control panel, it is listed as an EMU0k (or some such designation) which I understand may mean the card has gone bad.
8. The network fiber connection also periodically came up as yellow exclamation mark or working based on what was going on above.
It appears that these problems may be symptoms the card is going bad based on some other posts I found? Something about a scrambled EPROM? I do have a new unused Audigy ZS card I can try.
What is the best approach to put in another ZS. Delete the driver, shutdown, pull the card and put the new one in? And of course plug in the breakout box to it. Will it "find" the new January 06 drivers upon install or will I have to re-install those again on this new card. I know it is the same card but I assume the ID will be different.
If I need to re-install the drivers, do I just re-run the install or do I need to run CTZAP etc. first? I already have all the applications loaded off the original CD and would prefer not to have to do all that again...
Thanks again,
BJB
Message Edited by BJB on <SPAN class=date_text>08-22-2006 <SPAN class=time_text>09:4 AM
Message Edited by BJB on 08-22-2006 0:50 AM

Audigy suddenly stops working after doing chkds

System: P4800D-X mobo
??? Pent 4 HT
??? 3G memory
??? Hitachi 300G sata hd
??? Toshiba dvd burner (oem from micro center)
??? Audigy sound
??? Ati 9600 video card
Last December my system started to act sluggish and eventually crashed on me. Pulled the hd out and did a chkdsk with /f option using another comp I no longer have now. It fixed whatever caused the files to be corrupted and system has been working fine since. Although my sound card no longer works and for some strange reason XP home wants to load two drivers for the DVD burner. Causing this to not work as well.
Lately, I've had a bit of spare time and have been trying unsuccessfully to get the sound card to work again. I've read the FAQ on potential resolutions. Oddly, without reading it, I had already done most of those suggestions. I've totally wiped the drivers out more times then I care to count. Even went so far as to boot into safemode to double check that they weren't installing there. I've even gone to the extent of running a registary cleaner just to make sure there's no residual left overs.
Here's the odd part now. Digging even deeper into my system. The main driver for this card is CTAUD2k.SYS. In MSCONFIG "tools", this driver is listed as being one that has to be manually loaded, not loaded automatically. Odd that is. Even odder still, when I run DXDIAG, when I click on the sound tab, I get a 0X88780078 (no driver) error. Yet when I go to music, the windows synthesizer test, it comes back with the same 0X88780078 (no driver) error as well. The other two test pertaining to SB Audigy DirectMusic Sythesizer [EF40] and the SB Audigy Audio [EF40} both work and I can actually hear music!!! Strange, eh?
Just for the record. I have gone to Control Panel -->Sound and Audio devices--->Creative SB--->Properties--->Properties. All three "options" (Audio devices, Midi devices and instruments, Mixer devices) are turned on.
Other oddities. When I tried to do a "detect creative devices" from the support page, it said I don't have any creative devices installed on my system. Go figure!
Any suggestions would be greatly appericated.
Thanks
Jaxx

I've thought about that. Actually thought of doing a complete reinstall of XP home. However; I've a ton of music that I had just ripped as mp3's and I haven't had a chance to burn off yet. Also, while Asus does make some quality products...my particular mobo isn't one of them. The P4S800D-X motherboard has several issues. Like it can't handle sata 2 dri'ves, even backward compatible ones.
To do a reinstall or even repair on my system. I'd have to fix the dvd/cdrom first, and then it's like the chicken and egg situation of windows 95. XP wants to handle the drivers of my sata dri've as a scsii one. To do so you have to add them when prompted during the windows xp install process. Only it keeps looking for them on CD. No CD came with my Hitachi HD. It didn't need them. I can of course get drivers for the mobo that handle the scsii, but that would be placed on a floppy. And windows won't read the floppy!!!
There is a work around for installing the SISRAID drivers for the dvd/cdrom. But I'd need the dvd/cdrom to work to do them!
Things I forgot to mention or changed since I posted. I did upgrade reciently to XP home sp3 beta. I've upgraded to dx 9.22c (current as of end of march '08). I've done a google of the 0x88780078 error message. Seems this was a common error message a while back. I've tried many of the things that were suggested to fix that error message. None have worked. I've also tried at one time to install the on board ac'97 audio. And no such luck...this HAS to be a windows issue.
Since folks seem to upgrade video and audio cards alot, you would think that I could go to MS or even some website and get a "package" of all the windows audio .dll's and drivers and a how-to to clean them up and re-install them.

Creative Audigy 2 ZS Notebook install probl

Lets start off with the system owned:
Acer Aspire 9920G, Windows Vista Home Premium x86 32bit, Intel Core 2 Duo processor T7500 (2.2GHz/FSB: 800MHz/4MB L2 cache), 4GB DDR II RAM (2x 2GB), 2x 250GB (5400rpm S-ATA), NVIDIA GeForce 8600M-GT 280MB TC.
With a realtek onboard HD soundcard.
Now here's the problem:
I purchased the Creative Audigy 2 ZS Notebook last monday, went home and read the instructions.
I made sure to disable and uninstall the onboard card before hand and then pushed the card into the PCMCIA slot and press cancel on the automatic driver search vista gives me, afterwards starting the installation of the vista drivers that i downloaded seeing a small sticker on the box notified me that the installation cd would only work on XP.
Mind you, this is on a clean install, i reinstalled the whole system in the weekend and made a full backup that can be put back in less then 40 minutes in case something would go wrong.
Anyway, next thing i know after starting the install the system freezes entirely at the point where the installation says: "Updating windows drivers".
Hard reboot is the following action ofcourse, system freezes up and refuses to boot only giving me all the nifty blue lights and a black screen.
I pull out the zs notebook and reboot, works fine, however the second i push in the zs notebook the whole system freezes and i have to pull the plug yet again to force it to reboot.
Only action left is putting the backup back and everything works fine again and now i can actually push in the zs notebook card again without the system crashing.
I have tried multiple things after that reinstall so far with multiple results:
- Installing the drivers listed for vista in the drivers section: install freezes, have to reset by cutting the power, but i can reboot with the card still in the laptop, however its not installed at all nor are any programs installed.
- Installing with daniel's drivers: install freezes, cut power to reset and laptop refuses to boot with the zs notebook card in the slot and when in windows the card is pushed in the laptop freezes up yet again.
- Installing either of both drivers in safe mode results in a normal correct install: no freezing or crashing however the second i boot up in normal mode the laptop freezes before loading windows and the power has to be cut yet again.
So far every time this is fixed by using the recovery backup i made to have everything to normal again.
Probable cause that i was able to find:
If i install in safe mode the onboard sound card doesnt get loaded at all, then the installation of the zs notebook runs correctly.
However, in normal mode even if i disable and uninstall the drivers for the onboard card when the install runs it triesto install both the "Creative Audigy Audio Processor (WDM)" drivers for the audigy zs notebook, but it also tries to reinstall the realtek onboard, and i have no clue how to get rid of that since there is no option to disable the onboard soundcard through the bios at all.
Either way, the only time the laptop actually freezes is when the "Creative Audigy Audio Processor (WDM)" gets installed.
If that process doesnt manage to install itself the system doesnt crash, but doesnt see the ZS notebook card either.
Any ideas of random throughts that might help me solve this problem
Also, sorry for the long post, but i tried to make everything as complete and detailed as possible because i really want this fixed seeing i own both an older 5. creative sound set and a logitech z5500 with THX and would like to be able to run both on my laptop when i am at home.
Either way if i end up not being able to fix this i might end up swapping in the audigy 2 zs notebook for the x-fi xtreme audio notebook, problem there is though that it does not have THX and that i'll aslo have to seperatly buy the docking cable.
With regards,
Natharneal.
Message Edited by Natharneal on 05-23-2008 07:35 PM

Thank you for the reply split0,
as for the informati've post, thank you for the compliment, i tend to not open a thread at all unless i have spent enough time on the problem and searched around enough for solutions, and after that i only post if it has enough info regarding everything in inside the thread.
In regard to the known incompatibility list, unfortunatly this is one of the things i checked beforehand already.
The PCMCIA adapter in my laptop is a Texas Instruments PCI-8x2/7x2/6x2 CardBus-controller.
Which is one of the most common controllers and should normally not cause any troubles at all, also in another thread on this forum i found a differant driver for it, i even tried that with no result sadly.
At the moment personally i am thinking the whole problem lies within not being able to uninstall the onboard sound card to full extent somehow, and while i posted here i also have all this info in a direct message sent to creative, and even acer for that matter.
In hopes of some kind of solution for this so i can keep my hopes up for not having to return the card itself.
What bugs me is that there is option at all to disable the onboard sound through the bios.
Because right now whenever i install the ZS notebook card it checks hardware for the onboard first installing it again, then setting priority for the zs notebook.
This is what seems to result in the crashes through a conflict in drivers in my idea, but thats just a hunch which i cant do anything about currently in regard to testing unless someone has an idea for me to try.
Message Edited by Natharneal on 05-23-2008 0:54 PM

Audigy(1) Platinum PCI Not Detected By Installation CD In New Desk

Hello, I just updated to a new computer and pulled my Audigy Platinum SB0090 (with the front dri've panel) out of my old system and installed it in my new systemell E52 (AMD dual core)Windows XP SP23GB memory?) I disabled the onboard sound in the BIOS.2) Installed the Audigy Sound PCI card and dri've panel.3) Upon boot, Windows XP installs the Firewire and Gameport automatically. I tell it "no" when it prompts my to install audio device drivers.4) I try to install the current Audigy Platinum drivers from here, SBAX_WBUP2_LB_2_09_006, but it tells me no Audigy is detected and won't install.5)?I try to install the drivers from my original installation CD (PN: 220ML0003067) and am also?told that my?Audigy is not detected.6) The new PC has two PCI slots, 3 and 4. is PCIe6, 2 is PCIe. I've tried both PCI slots to no avail. The BIOS shows an audio device in whatever slot it is in. Partial Solution:7)? I went ahead a told Windows XP to search for drivers and it'sdid find?them on the original installation CD and installed them. I now have basic operations, but no dri've panel access. However, both installers above still cannot detect the Audigy. In Device Manager I now show:- Sound, video and game controllers-- Audio Codecs-- Creative Audigy Audio Processor (WDM)-- Creative Gameport-- Legacy Audio Drivers-- Legacy Video Capture Devices-- Media Control Devices-- Video Codecs?All of the above devices are working properly. Apparently I will not be able to easily get these installers to work. Is there a way I can manually?install the drivers neccessary to get current and full functionality of my Audigy and front dri've panel?Thanks

This is my view. It's all OK. It looks?if the Plug And Play function doesn't work. IRQ 0?Timer di sistema?OK
IRQ ?PS/2 Keyboard?OK
IRQ 4?Porta di comunicazione (COM)?OK
IRQ 6?Controller disco floppy standard?OK
IRQ 8?Orologio di sistema CMOS a tempo reale?OK
IRQ 9?Sistema compatibile ACPI Microsoft?OK
IRQ 9?SCSI/RAID Host Controller?OK
IRQ 3?Coprocessore matematico?OK
IRQ 5?Intel(R) ICH8 Family SMBus Controller - 283E?OK
IRQ 6?Intel(R) P965/G965 PCI Express Root Port - 29A?OK
IRQ 6?ASUS X950 SeriesOK
IRQ 6?Intel(R) ICH8 Family USB Uni'versal Host Controller - 2834?OK
IRQ 6?Intel(R) ICH8 Family PCI Express Root Port - 283F?OK
IRQ 7?Intel(R) ICH8 Family USB Uni'versal Host Controller - 2835?OK
IRQ 7?Intel(R) ICH8 Family PCI Express Root Port 6 - 2849?OK
IRQ 7?Generic Marvell Yukon Chipset based Ethernet Controller?OK
IRQ 8?Intel(R) ICH8 Family USB2 Enhanced Host Controller - 283A?OK
IRQ 8?Intel(R) ICH8 Family USB Uni'versal Host Controller - 2832?OK
IRQ 9?Intel(R) ICH8 Family USB Uni'versal Host Controller - 283?OK
IRQ 9?Intel(R) 8280HR/HH/HO SATA RAID Controller?OK
IRQ 2?Controller host Texas Instruments IEEE 394 compatibile OHCI?OK
IRQ 22?Creative Audigy Audio Processor (WDM)?OK
IRQ 23?Intel(R) ICH8 Family USB Uni'versal Host Controller - 2830?OK
IRQ 23?Intel(R) ICH8 Family USB2 Enhanced Host Controller - 2836?OK
IRQ 23?Controller host OHCI compatibile IEEE 394?OK
IRQ 23?Hauppauge WinTV-HVR 67xxx Capture Device?OK

ASIO USB Audigy 2 NX Bad Firmware and very old drive

Operating System?? : Windows XP Professional (5., Build 2600)
??????Service Pack 2 (2600.xpsp_sp2_rtm.040803-258)
Language??? : English (Regional Setting: English)
System Manufacturer: Hewlett-Packard
System Model?? : HP Compaq nx60 (PC49AV)
BIOS???? : KBC Version 39.2A
BIOS Date??? : 2006/07/27 (YYYY/MM/DD)
Processor??? : Intel(R) Pentium(R) M processor .73GHz
Memory???? : 504MB RAM
DirectX Version?? : DirectX 9.0c (4.09.0000.0904)
DxDiag Version?? : 5.03.2600.280 32bit Unicode
Creative Product-PID
Product???? : USB Sound Blaster Audigy 2 NX
Description??? : USB Sound Blaster Audigy 2 NX
Model No.
?? : SB0300
S/N????? : MASB03006350000K
Driver version??? : . 0. 0
Firmware version? : . . 5050 (Factory Default)
PID????? : 0 03 00 00 00 00 A0
Creative Software
Audio Device Selection .0.06
Common Audio Driver Interface .03.34
Creative EAX Console 2.05.06
Creative Entertainment Center 3.00.55
Creative Graphic Equalizer .52.53
Creative MediaSource 3.30.2
Creative MediaSource Go! 3.0.5
Creative MediaSource Player Skin Pack .0.08
Creative Music Store Plugin .00.3
Creative On Screen Display .00.0
Creative Speaker Settings .54.08
Creative System Information .00.26
Creative Windows Diagnostics 3..06
MediaSource CD-ROM Burner Component 3.0.8
MediaSource Detector 3.00.8
SoundFont Bank Manager for Windows 2.00.06
Surround Mixer 3.52.54
Problem One:
I get the following results
]I get the following results
Speaker mode ?Function ?? USB . ???? USB 2.0
2.0 ???? Playback?? Up to 24-bit/96 kHz ? Up to 24-bit/96 kHz
????#Record ?? Up to 24-bit/96 kHz? Up to 24-bit/96 kHz
4/5.
??Playback?? Up to 24-bit/48 kHz ? Up to 24-bit/48 kHz
????#Record ??? Up to 24-bit/96 kHz ? Up to 24-bit/48 kHz
7. ??? Playback ?? Up to 6-bit/48 kHz ? Up to 6-bit/48 kHz
????#Record ??? Up to 24-bit/96 kHz ? Up to 24-bit/48 kHz
I DON?T GET ANY ERRORS MESSAGE?S!
I DON?T GET ANY BANDWIDTH ERRORS.
According to the User manual, I should get 24-bit/96 kHz in 7. speaker settings on Playback on USB 2.0.
I do have USB 2.0 port! And my USB Sound Blaster Audigy 2 NX is plug into it
I have downloaded the Microsoft and Creative newest updates available on the internet.
If I downgrade the USB Sound Blaster Audigy 2 NX firmware
to v..0509 (Laterst Web version)
I get the following results
Speaker mode ?Function ?? USB . ???? USB 2.0
2.0 ???? Playback?? Up to 24-bit/96 kHz ? Up to 24-bit/96 kHz
????#Record ?? Up to 24-bit/96 kHz? Up to 24-bit/96 kHz
4/5.
??Playback?? Up to 24-bit/48 kHz ? Up to 24-bit/96 kHz
????#Record ??? Up to 24-bit/96 kHz ? Up to 24-bit/96 kHz
7. ??? Playback ?? Up to 6-bit/48 kHz ? Up to 24-bit/96 kHz
????#Record ??? Up to 24-bit/96 kHz ? Up to 24-bit/96 kHz
This would be wonderful but, the older firmware makes the USB Sound Blaster Audigy 2 NX, unresponsi've in -+ 5 minutes.
All Programs are unresponsi've after 5 minutes, if I unplug the USB Sound Blaster Audigy 2 NX my programs start to respond again. Resetting the firmware to factory default (v..05050), I get no problems, except that the USB Sound Blaster Audigy 2 NX response on a USB 2.0 port as if it'ss plug-in on a USB . Port.
I don?t have any problems with any other USB 2.0 hardware! They all work fine and I DON?T get any error telling me I would get High speed if the hardware was plug into a USB 2.0 plug. BECAUSE IT IS A USB 2.0 PORT!
The problem lies in the with in the firmware.
Would you please update the firmware.
In Creative Device Control the USB Connection Speed box.
Your device is Connected at:
Is grey, I can't set any thing. Why not?
Suggestion One:
For technical Personal only!
The drivers Creative releases are based on the Extigy.
If I look at the drivers you write for the PCI range (Audigy, Audigy 2 and Audigy 4 Series) they are better.
The Sound Blaster USB Range, Especially the Audigy Range can do so much more with the right drivers.
I suggested, you create a driver for the USB Composite Device. That emulates a PCI slot. This would allow the External Sound Blaster USB range to install your new and very advance PCI drivers.
Folder structure:
Drivers
-support
?????-amd64
?????-i386
???-wdm
?????-common
???????-amd64
???????-i386
?????????-thunk
?????-Lang
???????-amd64
???????-i386
?????-win2k_xp
???????-amd64
???????-data
???????-i386
Example:
By adding in wdma_emu.inf
[Creative]
; EMU0K chip (SBLi've!, APS)
%EMU0K.DeviceDesc%=EMU0K_Device,PCI\VEN_02&DEV_000 2&CC_04000
; USB range (SBLi've!, APS)
%USB.DeviceDesc%=USB_Device,PCI\VEN_02&DEVXXXXXXXX XXXXX
Adding in the Data folder, a data file for the USB Sound Blasters Audigy 2 NX would be ctp0300w.dat this tells the drivers which kind of features the SB0300 has.
It should detect if it'ss a Creative EMU0K Audio Processor (WDM)
or Creative Audigy Audio Processor (WDM)
If this is not possible at the very most I would like the following software to work with USB Sound Blaster range.
Audio Console
AudioHQ
CtPanel.exe
EAX Editor
Speaker Calibrator?
THX Setup Console (This is only software rendering, not limited to selected devices works fine on my Sound Blaster Li've! Value, CT4832)
CTASIO(ASIO 2.0 or .0, The Sound Blaster Audigy 2 NX Support ASIO, You just didn?t include it in the drivers)
In EAX Console under Effects tab.
There is only a Environment
I?m sure that the Sound Blaster Audigy 2 NX can support.
- Environment
- Advanced EQ
-Special FX
-Custom
-Studio
-Karoake
Again you based it on the old Extigy drivers it'ss the hardware is not limited!
In Surround Sound Mixer under the Advance Button there should be a Balance/Fade window. Again there is no such window because you base it on the Extigy.
In Speakers Settings under Speaker Selection You should add the marker for Synchronize with Control Panel. (This is only a Drivers limitation)
The New PCI Drivers add branding in Microsoft Volume Control and in Sound and Audio Device Properties.
Can you add Branding for the Sound Blaster USB.
In
Sound and Audio Devices Properties
Volume (Tab)
Speaker Settings (Window)
Speaker Volume? (Button)
If you click on the Speaker Volume? button. It should give you the option to set Channel to Channel 8, currently there are only Channel and Channel 2
Sound and Audio Devices Properties
Volume (Tab)
Speaker Settings (Window)
Advance? (Button)
Effects (Tab)
Effects: (Drop down)
Is Empty there is only None. Can you please all of the EAX Advanced HD Effects
To conclude would you please improve the Sound Blaster USB Driver! Or just create a new range driver for the Sound Blaster USB!
Yours truly,
Horst Johan Kaiser

How can u see the firmware?on this card? ?I wanna know which date my firmware has on my Elite Pro and if it is the latest one?But Creative seems not to give answers to this (read about it from another person who asked this)

Audigy 2 ZS Platinum won't work with Windows XP Pro 64

My system has both normal Windows XP Pro & Windows XP pro 64bit installed.
The problems is that I can't get any sound on WinXp 64. The device manager has given me a "Code 39" on the "Creative Audigy Audio Processor (WDM)" device. This hasen't happened to all the other devices attached to the card. WinXP 32 has no problems in loading the drivers or playing sounds.
My system specs are as follows...
Asus P5ND2-SLI Deluxe motherboard with 0705 BIOS installed
Pentium 4 EM64T 3.8GHz 670 LGA775 2MB L22x Corsair VSGB667D2 PC-5300 GB x28MBx64 240 DIMM 2x BFG GeForce 7800GTXCreative Labs Audigy 2 ZS PlatinumA Segate 250gig SATA hard dri've, a Segate 300gig SATA hard dri've & a Samsung 40gig SATA hard dri'veLITE-ON SOHW-693S DVD BurnerPioneer DVR-0D DVD Burner
I am using the latest drivers from the CreativeLabs website & pretty much the latest drivers for all my hardware.
Any ideas?

Never mind.
I've just solved the problem. I moved the card to another PCI slot, used Driver Cleaner Pro to remove the driver & reinstalled the driver.
Thank you anyway thou.

Audigy Audio Extention Connec

Similar Messages

Maybe you are looking for