Audigy Drive bay not 'seen' by Audigy 2 ZS card....Help!!!

As it says, have physically linked bay to card.....but bay just wont 'wake up'
Can someone point me in the right direction?
Thanks
Kev/UK?

I have this card and I have had the problem you are having. This occurs for two reason,
) You have the data cable reversed on one end of the connection. This is a PIN labeled on both the card and the dri've bay. Match the pink edge of your cable to PIN on both the card and dri've bay.
2) you have not plugged in the four pin power adapter on the dri've bay from your power supply. Check both of these things, correct the problem if it exists with your computer powered off, and power up again and recheck your audigy control panel to see if the dri've is now visible

Similar Messages

Cd/dvd drive will not receive a disc, can anyone please help?

cd/dvd drive will not receive a disc, can anyone please help?

Apple Portables: Troubleshooting the slot load optical disc drive
Cures for an uncooperative CD/DVD drive

Time machine backup on external firewire drive is not seen by restore or migration assistant

Hi,
today the harddrive on my Aluminium iMac gave up the ghost. I have been backing up my system using time machine, so I wished to restore it. To my great annoyance I found that neither the restore option in Lion's installer nor the migration assistant after install allows me to select that drive!!!
I have checked the drive, it's ok. I connected it to another Mac, it can read it just fine. Why the **** is it not appearing in the list of available backups?!

Hi Bob,
I would like it to appear along with the time capsule it self under shared, so when I click on the time capsule I would see two drives the time capsule and right below or above the hard drive. and I would like to be able to see it in the airport utility under disks under the time capsule in the drive screen, but the drive is not visible in either locations.
yes I have read many places that the drive need external power supply, as this drive is quite large 1,5 tb I did take one with external power supply. I do however have two other drives one 500 gb and one 750 gb without external power supply and they both work perfectly on my time capsule "plug and play" like it is supposed to, funny enough one of these drives do have the partition master scheme as master boot record even as I have seen several discussions where it is stated this would not work. on these new drives I have tried with the three different partition master schemes I have tried with mac OS extended formatting as well as FAT 32 formatting, I even formatted the drives on a windows machine to see. but it still do not appear when it is connected to my time capsule. Before my time capsule get the blame for this I have to add that I have tried on two other time capsules - though in other environments - with the same result.
so please any new idea is very appreciated.

Toshiba external hard drive is not seen by my time capsule

I am trying to connect an external hard drive to my time capsule, I am doing this with other hard drives and it work perfectly, but I just got a toshiba 1,5 tb drive with external power supply and my time capsule simply ignore it, it is not shown in the disk part of the airport setup screen, if I connect one of my other external drives it does show both in finder and in the airport set up screen.
I have tried to format the drive in all the different ways I could, as I read that if the partition map scheme is master boot record it may have problems, and if the drive is not formatted as either fat32 or mac OS extended it will not show. no matter what I am doing it still is not picked up by the time capsule when I plug it in.
it work perfectly if I plug it directly into my macbook. I have truly run out of ideas. I actually have two identical toshiba drives so I tried the other one to be sure it was no a problem on the first drive, but it act in the exact same manner. I tried to look at some of the hidden files, but not being a computer expert it did not make much sence to me.
please somebody help out here.

Hi Bob,
I would like it to appear along with the time capsule it self under shared, so when I click on the time capsule I would see two drives the time capsule and right below or above the hard drive. and I would like to be able to see it in the airport utility under disks under the time capsule in the drive screen, but the drive is not visible in either locations.
yes I have read many places that the drive need external power supply, as this drive is quite large 1,5 tb I did take one with external power supply. I do however have two other drives one 500 gb and one 750 gb without external power supply and they both work perfectly on my time capsule "plug and play" like it is supposed to, funny enough one of these drives do have the partition master scheme as master boot record even as I have seen several discussions where it is stated this would not work. on these new drives I have tried with the three different partition master schemes I have tried with mac OS extended formatting as well as FAT 32 formatting, I even formatted the drives on a windows machine to see. but it still do not appear when it is connected to my time capsule. Before my time capsule get the blame for this I have to add that I have tried on two other time capsules - though in other environments - with the same result.
so please any new idea is very appreciated.

X-fi I/O drive bay not working (replacement for falty o

i have had the SB X-fi fatalty xtreamgamer card for a few weeks and i went out and got the dri've bay for it affter finding out that it did not work it was sent back to creative and i reci'ved a new one but this one all so is not working there is power to it but the X-fi sound card is not detecting the dri've bay. i have tryed changeing the power cables and done fresh windows and creative x-fi driver installs but the dri've bay still wont work is there anything else i can do to fix it

Hi Serpantine,
You might want to check if there is light coming from the Optical SPDIF Out. This tells you if the dri've is receiving power or not. Customer Support should be able to help you troubleshoot this.

Installing snow leopard on new hard drive - disc not seen or found

I can't provide too many details right now as my hard drive is out, and I'm trying to reinstall an operating system.
Problem: Installed a new hard drive purchased from reputable repair store. Last installation disc I have is OS X Snow Leopard. When I get to the point to choose where to install it, it is not seeing the new hard drive. I've double checked that the wires/bar connecting the actual hard drive are snug. Could there be another problem? Something to do with Lion? I've read several forums, but to no avail....
Computer: Macbook Pro unibody. Probably mid 2009.
OS X: The last one before Maverick... 10.8.5
The reason I am putting in a new hard drive is that my computer was having trouble starting up or unexpectedly crashing, although I could do a Safe start or Diagnostic (d). So, on the old hard drive, I did PRAM reset, and Disk Utility, but could not run the Apple Hardware Test, so I took it in. There is a little issue with battery not being full, but they did not think that was causing the problem, and that it was probably a hard drive issue. With the new harddrive... they suggested trying to download an OS from linking to another computer by firewire.... The other computer, (Macbook 2 GHx intel Core 2 Duo, 4 GB 10067 MHZ DDR3, OS 10.8.5) does not have a firewire, but does have thunderport, so I tried doing a Target start to reboot... but Macbook Pro did not read the 2nd computer (Macbook). Then I found my old Snow Leopard disk and here I am...

If the repair store installed the drive, I'd take it back and let them make it work. Take your Snow Leopard DVD also.

USB pen drive mounts not seen in system.log. Why?

Any idea why USB pen drive mounts are not loogged in system.log? A WD Paasport drive mount shows up in system.log. Any idea why this is the case and how it can tracked/logged?
It would be nice to have a record of any externals that are being mounted on an OS X client by a user.
MacMini Mac OS X (10.4.9)

Ok, that's it. I read a few posts in the "...SuperDrive won't accept my CD.." section. and it seems some people are just swapping optical drives like mad, ready to accept that the kit is crap, and "...oh, well, I sure hope this one works better...".
But one guy had the brains to have a look inside. Turns out dust had accumulated in the drive and on the connectors, and when he cleaned them, and unplugged and replugged them, it worked fine. So that's what I did. Took it out and put it back in. Amazing the stuff I cleared out! I also un- and re-plugged the power cable and the data ribbon at the mutha board and bingo!. We have disk, and I can breathe again.
Recommend to others they pretend they've bought a new drive, do a remove and reinstall and be very fastidious. You may not need a new one after all. I just love it that stuff can still be FIXED!
Thanks to Lou and all of you who share your experiences. It's like my brain is suddenly soooo huge...

ENVY Dv7 dual SSD's win8 sees only drive 0, drive 1 not seen.

I have an ENVY DV7-7243cl laptop, I replaced the original 1TB HDD with my seagate 750 GB solid state hybrid drive, installed windows, no problems there, however yesterday I installed a second SSD (crucial 512GB). The BIOS sees both drives, but windows only sees the 750GB boot drive, if I put the new SSD on external USB windows sees the drive and allows me to initialize it. I'm not sure why two SSD's won't work together. Is there something missing a driver perhaps etc... I have the latest BIOS version F24
Hp ENVY DV7-7143cl
16GB ram
windows 8 Home
Seagate Momentus XT 750GB SSD hybrid and Crucial 512GB SSD.

Hello ggetchell,
Take a look at the HD & SSD Care and Maintenance Measures manual. On page 7 it talks about advanced formatting for Windows installations...maybe something there may help?? This document may help as well. Please let me know.
Good luck!
↙-----------How do I give Kudos?| How do I mark a post as Solved? ----------------↓

New internal hard drive replacement not seen - why?

I have replaced the internal Seagate Momentus 7200RPM, 160Gb drive on my 2007, 17 inch MBP- with a Seagate Momentus 7200RPM 500 GB. I used Super Duper to clone the original drive - and the new drive will boot up OK - BUT only when in an external enclosure! Not as the new internal drive.
I am using Mountain Lion 10.8.2
When it is in place in the MBP at start up I get the flashing Question mark. I have tried booting from another backup drive - to use Disk Utility to repair the new drive. but it does not show up! I have also tried booting from OS Mountain Lion on a flash drive - but, again I cannot 'see' the new Seagate internal drive to repair it!
I have checked all the connections (taken the new drive out and put it back in several times) all connections appear to be Ok.
I have tried resetting PRAM - no difference.
So, why does it only work when connected as an external drive - and does not show up when connected as an internal drive?
PLEASE - can anyone help?
thanks
Alan

Hi again - thanks! I recall the cable snaking around and it certainly does look as in your pic.
As I put in my first post - I do have an enclosure and it does work from that. However, it is only via USB 2 so is slow. As I write I have booted up from my Firewire 800 backup drive.
I will explore bot iFixit and Powerbook medic and see if they can send these parts to me - so thanks to you both for all this helpful advice!
One final question - since it WAS working when I first took out the original drive it may be that I have EITHER pulled too hard and broken a connector - or just pulled one loose
Is ther any way I can test? How are the other ends connected? The large block of double connectors to the drive is clear - but I have not tried specifically to remove any other ends!

DVD/CD drive is not seen by 6460DWU T61 and XP Professional system

Dear friends,
I have laptop 6460-DWU T61 with XP Professional.
I load systematically all new updates which I receive from Lenovo and one day I saw that my computer cannot see my DVD/CD drive. It disappeared from “My Computer”. I do not know when it was happened. Does Lenovo create problems for his users ?
When I load from “Control panel” “Add hardware Wizard” I saw yellow “!” at HL-DT-ST DVDRAM GSA-U10N and after clicking Next I saw message “Windows cannot load the device driver for this hardware. The driver may be corrupted or missing. (Code 39)”.
After I uninstalled the device using “Device Manager”, rebooted my laptop and installed it again. Nothing was changed. Again yellow “!” at HL-DT-ST DVDRAM GSA-U10N and my computer cannot see my DVD/CD drive.
I tried temporary find other solution and connect DVD/CD drive by USB port. And again problem. My computer cannot see the new drive, yellow “!” at HP DVD Writer 557r USB Device and the same message “Windows cannot load the device driver for this hardware. The driver may be corrupted or missing. (Code 39)”.
Great ! What can I do?!
My big request is how can I fix the problem? May I use the bellow solution?
I intend create the fixcd.reg file described by Mr.JohnWill at
http://forums.techguy.org/multimedia/528972-itunes-blocks-cd-rom-recognition.html
However I do not know in which directory set the file for sure.
Can somebody tell me, please?
I appreciate it in advance, thank you.

I'm not entirely sure what the OP's situation is, but this:
"They sold me it without CD to reinstall XP Windows. I do not have CD which I can use to reinstall my Windows. My computer is preinstalled with the MS Windows® XP OS, but is supplied with a MS® Windows Vista® OS. ... The Windows Vista recovery disc set provided with my computer cannot reinstall the Windows XP OS."
would seem to indicate that the machine was purchased with a Vista license and a pre-installed XP downgrade. That's how several machines that I was involved with (mine and friends') arrived.
They were shipped with Lenovo XP images installed - including the recovery partition and tools for XP - and a set of Vista factory media as well.
[edit] Small correction: my T400 had Vista installed and XP media in the box. The other T400 units had XP installed and Vista media in the box.
Z.
The large print: please read the Community Participation Rules before posting. Include as much information as possible: model, machine type, operating system, and a descriptive subject line. Do not include personal information: serial number, telephone number, email address, etc. The fine print: I do not work for, nor do I speak for Lenovo. Unsolicited private messages will be ignored. ... GeezBlog
English Community Deutsche Community Comunidad en Español Русскоязычное Сообщество

Over the last week, my external hard drive is not seen by mac, over the last week, my external hard drive is not seen by mac

My laptop is Macbook Pro and I used to use an external hard disk, which used to work fine with me. However, over the last week, the Mac system started not to recognize the hard disk and accordingly does not see it.
Any solutions / suggesions?
Regards

Did you test your external hd in another machine? did you test with another cable?
I don't know if its helps, but try to reset the PRAM.

I have formatted the macbook pro 13,now i see 150GB drive and 350GB drive is not seen,pl advise to recover the 350GB and make single hard disk without partition

i have formatte the macbook pro 13 as it was slow and with boot camp,at the time of format sesstion stopped at 61% and was asking 6 hours to
complete.this was for 24 hrs on condtion so i skipped and now i find only 150 gb reserved for boot camp,where 350 allocated for mac is missing
pl advise the solution
i wish to install maverick so i started this on my 10.6.8 verstion macbook
thaks and regards
Dr srinivas

Use the trackpad to scroll, thats what it was designed for. The scroll bars automatically disappear when not being used and will appear if you scroll up or down using the trackpad.
This is a user-to-user forum and most people will post on here if they have problems. You very rarely get people posting to say there update went smooth. The fact is the vast majority of Mountain Lion users will not be experiencing any major problems with the OS, or maybe with apps which are not compatible, but thats hardly Apple's fault if developers don't update their apps.

IPod touch 5th gen will not connect to iTunes, also apple mobile device usb driver does not appear in device manager. PLEASE HELP.

I recently purchased my iPod touch with no issues. After updating to iOS 8.1.1 I found that my iPod would no longer appear in the latest version of iTunes and when I searched for Apple Mobile Device usb driver in the device manager, it was nowhere to be found. I've already uninstalled and re-installed ALL components of iTunes and read every single help article. I've tried everything. What went wrong?

See
iOS: Device not recognized in iTunes for Windows
- I would start with
Removing and Reinstalling iTunes, QuickTime, and other software components for Windows XP
or
Removing and reinstalling iTunes and other software components for Windows Vista, Windows 7, or Windows 8
However, after your remove the Apple software components also remove the iCloud Control Panel via Windows Programs and Features app in the Window Control Panel. Then reinstall all the Apple software components
- Then do the other actions of:
iOS: Device not recognized in iTunes for Windows
paying special attention to item #5
- New cable and different USB port
- Run this and see if the results help with determine the cause
iTunes for Windows: Device Sync Tests
Also see:
iPod not recognised by windows iTunes
Troubleshooting issues with iTunes for Windows updates
- Try on another computer to help determine if computer or iPod problem

When I upgraded my Mac Pro HDs I lost the capcity for 2 monitors. One monitor works fine but the second one is not "seen" by the Mac Pro. Help?

My MacPro is a dual quad core 2.8 intell processor system with 6 gig of RAM and 4 HDs. I recently upgraded the HDs from 500 gig each to 2 TB each. I did that by copying each existing hard drive to a new hard drive and then inserting the new hard drive where the copied drive had been. I followed all of the instructions for the OX system that came after copying and replacing the drive with the OX on it. Unfortunately now I can no longer use the 2 monitors that I used to use on the system. One monitor works fine, the second on is not found by the OX system and simply won't respond or receive a signal from the computer. Any ideas?

Have you tried a NVRAM / PRAM reset?
Shut down your Mac.
Locate the following keys on the keyboard: Command (⌘), Option, P, and R. You will need to hold these keys down simultaneously in step 4.
Turn on the computer.
Press and hold the Command-Option-P-R keys before the gray screen appears.
Hold the keys down until the computer restarts and you hear the startup sound for the second time.
Release the keys.

New hard drive does not get recognized by OS X server 10.6

Xserve disk utility does no see the new HD. It is not HD issue as I have tested drive in other carrier, switched drive in different bays, booted from Xserve 10.6 dvd and 10.6 Server image in our net boot. Drive is not seen by disk utility. Even put in an Apple original (Mac Pro) HD. We have verified that. memory, HDD carrier and HD Bay are not defective.

Thanks John for the reply. I tried different new hard drives as well as a HD from Mac Pro server.I did try drive in different bays. Other 2 drives in the Xserve are recognized in all bays.I even switced HD carrier. Nothing seems to work. I found the following notes in the Xserve manual. I could not fully understand that. May be you can help me understand this.
Xserve (Late 2006) includes three hard drive bays on the front panel. Hard drives come as
modules, known as Apple drive modules (ADMs), attached to carriers; they are removed from or
installed in the Xserve as a unit. ADMs have been available from Apple in various capacities for
all Xserve and Xserve RAID models, and in multiple interface types. Xserve G4 and Xserve RAID
use parallel ATA (PATA) ADMs, and Xserve G5 uses serial ATA (SATA) ADMs. Xserve (Late 2006) can
use SATA ADMs, and ADMs with a new, third interface type known as serial attached SCSI (SAS).
It is important to understand ADM forward compatibility and backward compatibility with older
Xserve models, since some combinations of ADM and Xserve or RAID work properly while other
combinations do not. The following table summarizes this compatibility.
Xserve G4 Xserve RAID Xserve G5 Xserve
(Late 2006)
Xserve (Early
2008)

Audigy Drive bay not 'seen' by Audigy 2 ZS card....Help!!!

Similar Messages

Maybe you are looking for