Audigy platinium 4 pro and M-audio 2496

is it possible to have these cards working in the same computer having one for listening music and the other for recordings(guitar and voice...the m-audio have two diferent channel) can you show me how? does it need a special configuration?
best regards from portugal
Grain

The Gigaworks set doesn't come with any bundled apps, the A4 installation CD ISO image can be downloaded here:?http://badboy.hub.io/?

Similar Messages

Audigy 2 pro and ATI HDTV Won

I just recently purchased an ATI HDTV Wonder. I want to have audio coming in directly through the Optical SPDIF input on the IO Hub on my Audigy 2 Pro while the video is coming in through the HDTV Wonder card.
What I am noticing is a slight audio sync issue. I think this is a known issue, is there a work around or how can this be corrected?
Dan

If you are just surfing then just put the cards in and that would be it. If you are not using the built in tuner then don't worry about the extra wiring. You might want to return that nice video card and get your cash back and buy a cheapie instead

Audigy 4 Pro and broadcom 5

Hi i have a Audigy 4 Pro card and MSI KT600 Delta motherboard that have a broadcom 5788 LOM but after a few minutes after bootup my sound card block the network but i get the status that i have connection and all.
I have tried to update BIOS, all drivers that can be found to the motherboard, Changed PCI slot and tried to force all free IRQs but no results. So anyone that have a clue how to fix this would be great

Question for music producers ! MacBook Pro and my audio interface from Virus Ti doesn't seem to work properly after I updated 10.9.4 Mavericks

Hello
Few days ago I upgraded my Macbook Pro to 10.9.4 Mavericks And I’m using the sound card from the Virus Ti for all audio in/out and when I’m not producing music , I usually close my Logic and I use the Virus Ti as a sound card for listening to Soundcloud or iTunes on my Mac and the audio usually come out of my studio monitors , but right now even when everything is connected , the sounds from the web site is coming out from my Macbook speaker instead of my studio monitors ? and I already checked the “Output/Input” in preference and is already say Access Virus Ti and I already repair disc too ! ,
Right now when I’m using Logic to produced with Virus sound card everything is working fine and the audio is coming out of my monitors but as soon as I turn off Logic to use Youtube or other web site, the audio automatic switch back to laptop speakers ?
If anyone had this problems with their audio interface and OS 10.9.4 , please advise !
Your help is much appreciated : )

@michelle929 don't feel so bad, i too which i never would have upgrade to ff4, OMG, so piss., worse is they deleted the old version from my computer, how dare them..lol... but most of the thing i use now don't wanna work.. i want my 3.6.15 well i think that was the last one i had.. piss piss,,and Michelle your not whining , just stating the fact's.. give me back the old version Mozilla... can't even find it on here,, any one knows where i can find it... if not gonna have to go to a server an get it,,
thanks Lotta firefox. great job, not tell us first hand what won't work....:(

Why does the letter P show up when i try to record audio into Logic Pro and no audio is audible ?!

Can anyone pleaes help as I have occured this problem today and sent hours trying to fix it and not had any luck !?!?
I always record in audio by press "R" on the channel strip but today for some odd reason the letter "P" shows up and no audio is audiable ?
Can anyone tell me what's going on ............!?!?
"When I try to record in some audio and press "R" it chnages to the letter "P" and no audio is coming through ?!?"

This is because you have Punch on the fly enabled under Options (top menu)>Audio>Punch on the Fly.... signified by the letter P instead of the letter R

No audio in Windows 7 64bit with Audigy 4 Pro and Inspire 7.1 speakers

Hi, this is my first post in this forum. This issue is killing me?
Configuration:
Intel Core i7 920 2.66Ghz
DDR3 600Mhz PC2800 6GB Corsair XMS3 Classic CL9 Skt366
Samsung TB HD03SJ 7200rpm 32MB Spinpoint F3
Mobo ASUS 366 P6T SE
New Windows 7 installation, no upgrade, so everything?s new. Realtek HD integrated audio chipset works fine, so the speakers are ok. Obviously I want my 2005 Audigy 4 back, especially for its external box.
I can't get any audio out of my speakers, zero, nothing, nada. Windows 7 recognizes it and if I run the control panel?s tests the equalizer shows that music is playing but still I won?t ear a single note.
I tried everything:
-I checked Windows mixer, the output was correct and no ?mute? was selected, no SPDIF, no optical etc etc
-I deactivated the Realtek
-I tried to put the Audigy in different PCI slots?
-I tried the latest Creative drivers?
-I tried unofficial drivers?
What should I do now?
Maybe I could try:
-Updating the mobo bios. I don?t really want to do it unless it'ss absolutely necessary. My mobo is quite new anyway and from its bios updates I can't see nothing related to pci slots or audio issues.
-Playing around with the drivers: maybe I?m wrong, but I?suspect that, while installing creative drivers, every time I restart the system Windows 7 re-check the audio card and puts its Creative Audigy WDM? driver. I?m not too sure about this: from Windows device manager it seems that the drivers are updated and running.
Any ideas?

JProblem solved.
Apparently there was a clash between Windows 7 driver (?) and the one from Creative.
I had to use a specific software in order?to delete creative drivers and software.
After the erase of every piece of junk I could install creative official drivers.
Audio playback is fine, still I have s?to test recording...

Logic Pro and Basic Audio Units

Is anyone else having an issue with Logic Pro 9.1.8 and using legacy/basic audio unit effects located in the Audio Units > Apple location? It seems as though anytime I try to use an AU* type plugin with my project the EQ freezes like it did before the 9.1.8 update was applied. I've noticed the issue occuring when I have 8+ tracks with midi, samples, and Apple Loops in the project. The HD and CPU meters are very low (1-2 bars) and it just hangs. I don't think track count or track type has anything to do with this issue as my last project had ~24 tracks and did fine up until I added in AULowpass and that is when I started having problems with the EQ.

This is because you have Punch on the fly enabled under Options (top menu)>Audio>Punch on the Fly.... signified by the letter P instead of the letter R

Motorola HS820 will not pair with my Macbook Pro and now audio is broken...

My problem is two fold.
First i cannot connect my Motorola HS820 Bluetooth headset to my Macbook Pro. The bluetooth assistant pairs it succesfully but when it connects it immediately disconnects. All of the posts i that address this are either for g4 macbooks or do not work for me...
Second, now that i have attempted this connection i am having issues with several apps including firefox and mediacentral. Audio from these programs will not play. I get an error message saying there was a problem with configuration..

This is not related to the Intel platform (MacBook or MacBook Pro). Make sure the headset is turned on before you turn on your Mac. Then it should connect correctly.
To change the sound outpu, please go to Mac OS X > System Preferences > Sound > Output and change it back to the internal speakers.

HP Pavillion dv6500 with windows xp pro AND NO audio Driver!

i have a hp pavilion dv6500 laptop entertainment pc here with me. It came with windows vista but i downgraded to windowx xp pro. it runs alot smoother! Everything works great except one problem? The audiio drivers that the hp websites has does not work? I cannot find the right audio drivers? I have tried even letting windows update search for the drivers with no luck? Why are the drivers on the website not working? How can i get this to work? if i upgrade it to windows 7 can i intergarde the vista drivers to work with the windows 7 program? i really need help! Thanks!

The General XP Downgrade Guide for HP notebooks is what you need to read. This well written guide has helped (at least!!) thousands of forum members downgrade their notebook successfully. There is a section that applies to your notebook.
The issue you are having probably is related to not installing the MSUAA driver before the device specific audio driver.
****Please click on Accept As Solution if a suggestion solves your problem. It helps others facing the same problem to find a solution easily****
2015 Microsoft MVP - Windows Experience Consumer

Audigy 4 Pro and Logitech z-5500 5.1 speak

Hey ppl
I'm thinking of getting those two. I've heard there is an incompatibility issue with a digital connection between them, buts as I'm not interested in a digital connection, will an analog connection? I suppose the PCI or the hub has the required outputs ( left front/back, right front/back ? center/sub) for 5. analog.

Audigy 4 Pro - Remote Contr

Hey,?I've got an Audigy 4 Pro card which i've had from new since 2005.However, i've only ever had the remote control working once, around about the time i first installed the card. Since then it's not worked. I'm currently running the latest drivers and mediasource 5, and still not getting remote control. I've been told i need Creative Media Centre, and i need to enable the remote, but A) i dont know where to get media centre since it's not on the downloads site for the Audigy 4 Pro. and B) i've tried looking for the "remote control" tab in media source, but to absolutely no avail. Can anyone tell me how i'm supposed to get my remote control working again? please?Martin

Entertainment Center is most likely found in the installation CD (X:\Audio\EntCntr\), I don't know if the A4Pro software can be installed individually, but if?you can't, copy the whole CD to the HDD and then copy engine32.cab from X\Audio\Setup\ to the app installation dir. If you no longer have the installation CD, download the ISO from BadBoy's page. http://badboy.hub.io/?You can try RMX automation, its a free program that lets you configure the buttons in the remote: http://sourceforge.net/projects/rmx/?

Audigy 4 Pro - can only get 2 channel sound via SPDIF/optical connecti

I have two PC's, one with an Audigy 4 Pro and one with an Audigy 2 Platinum (A2P), I have my 5. speakers hooked up to the A2P and the A4P connected via the SPDIF to the A2P, I would expect to get 5. - both are setup to use 5. speakers, (I know that as a standard Digital coax/optical connections should handle multi speaker configs my entire A/V sound system (7. Dolby) uses optical and coax and it works fine).
If I run the channel test on the Audigy 4 I can get nothing but sound through the left and right speakers, if I run the test on the Audigy 2 (speakers direct connected) the sound is fine, if I reconnect the speakers to my Audigy 4 I get sound on all speakers so it looks like its an issue with the SPDIF and optical inputs (I tried both).
I have emailed tech support, I'm waiting for them to come back and tell me that the Audigy 4 cannot transmit more than two channels down the SPDIF/optical outs, thats my suspicion anyway, if that is the case then I'm not going to be a happy man and the Audigy will be going back to the store. Could be a driver problem of course as I cant believe they would implement Dolby and THX and only transmit two channels on the optical outs, that would be a bit dumb considering the primary use for digital connections is sound system interconnects.
Anyone with any ideas about this let me know, perhaps theres a hidden setting somewhere or a registry setting that switches the digital outs to carry all signals.

Just before everyone kicks off, heres a response I got from a tech guy at Creative themselves.
If you connect speakers to your sound card using a digital cable
(RCA/SPDIF or optical) then the software speaker test will only output
from two speakers. The reason for this is that the speaker test signal is
not in AC3 nor DTS format.
The signal on a digital connection is either
Optical SPDIF - which is either Stereo PCM signal or AC-3/DTS Bitstream
RCA SPDIF - which is either Stereo PCM signal or AC-3/DTS Bitstream
If you play AC3 (Dolby Digital) or DTS encoded signals, the amplifier
decodes this and outputs it to all 6 speakers (5 satellites & subwoofer)
discretely.
When playing back stereo signals (such as Wav/CD Audio or MP3/WMA files)
the amplifier may generate 5. output based on the incoming stereo PCM
signal, provided Dolby Pro Logic decoding is available and activated.
Therefore the speaker test should not be relied on when using RCA or
Optical digital connections.
This applies to all speaker systems equipped with RCA or Optical digital
connections.
This makes sense to me and I'm pretty happy with it, basically as the reply says above the speaker test does not encode to AC3 hence if you hook two Audigys together and run the test you only get 2 channel output, if you play a DVD which is AC3/DTS encoded on one Audigy and listen to speakers hooked up to the other when both Audigys are connected via SPDIF or optical you should in theory get full playback on all speakers. Hopefully
Cheers
Simon

Audigy 2 ZS and ASIO 24/96

I have seen several posts about how to use ASIO 24/96 driver for Audigy 2 ZS but they are pretty old now and the problem I have experienced is just a few years old.
I used the driver on my old XP 32 bit computer for critical recordings for highest possible quality though it was only possible in Wavelab for single track recording/playback. Running multitrack was too heavy for my computer. I then had a long break from music making and started again a year ago. I couldn?t get that driver work again but didn?t bother much as I didn?t have to record any external audio yet.
Last weekend I upgraded my computer to a quadcore cpu with 6 gig RAM and Windows 7 Pro 64 bit. I can now use ASIO 24/96 and it runs smooth and free from glitches - but it only works for playback. Whatever input I choose all I get is silence. The other two ASIO drivers works though but they cannot record in 24 bit/96 kHz. In worst case I could have used the WDM drivers only for the recording part but those does not work at all at any rate - I get so much dropouts that the recordings are full of "holes".
Has the drivers been changed during the years so actually can't record when using ASIO 24/96 driver? If it wasn?t for the fact that it didn?t work on my XP?system either I would have thought it was a Windows 7 issue.

Gorilla wrote:
For some reason I have an error message in ADIC Pro 5.
I have an Audigy Platimum Pro and I changed the audio devie type in the Preferences to SB Audigy 2 ZS ASIO 24/96 (FF40), but when I try to record and check the little monitor bar, I can see the levels, but I hear no sound. If I uncheck it, I see no levels, but I hear sound. I cannot record because of this sicne when I hear the sound nothing is getting recorder. I doublechecket everything but I cannot solve the problem. Please help me if you can
Thanks
Peter
Hmmm.. What the error message says?
Which input source you have selected to record from?
Have you selected the output port(s)?
Are project samplerate and bit-depth set to 24/96?
Does this issue occur when ASIO res is set to 16-bit/48 kHZ?
Is tehere a setting for monitoring on ACID audio/global properties (other than the ON/OFF found on every track)?
jutapa

Audigy 4 pro digital connection but no l

Hi
I have a soundblaster audigy 4 pro and i connect it to my amblifier denon with optical cable but when i play a dolby digital or dts sound i can't get the logo on the amblifier. I test it on clean install win xp sp2. The sound seems to bo ok but no logo. I use Power dvd latest version.When i play the same dvd on my desktop dvd player with optical connection everything is ok sound and all logo's display.
Do i have to enable cmss?
Please help.
Thank you
P.S sorry for my bad english.Message Edited by ASTRAPI on 06-2-2005 0:30 AM

CMSS is an effect used for stereo sounds, to emulate surround sound for them. It has no effect on the DVDs you're playing as you're just outputting the AC3 signal so the speakers can decode it.
If you're using a digital connection, then CMSS will not have any effect for other sound either, you need to connect through multiple analog connections to get that sound. A standard digital connection (coaxial and optical SPDIF) can only pass over either a stereo PCM signal, or an encoded AC3 stream (like on your DVDs). Normal sound like music or games will only be passed over as stereo PCM, so there is no CMSS effect there.
If you can connect your amplifier through several analog connections, then you can use CMSS aswell, otherwise your amplifier might have it's own upmix option like ProLogic.
Cat

Audigy 4 pro not work

i have a Audigy 4 pro and there is no power to the box every thing is pluged in so is it rma time

Hello , I was reading your post on the audigy 4 pro, I recently upgraded my system, from an abit an8 32x sli motherboard, to an asus? A8n 32x sli deluxe motherboard, and ever since I have not been able to get power to my Audigy 4 Pro IO BOX< just like you were having.
howevr my audigy 4 pro card is working cause i can still use my speakers, but the IO box is not getting power. I have latest drivers and motherboard drivers, would u possibly by chance have solved your issue, and if so how did you do it. cause I dont wana have to RMA, cause i think my warranty is up? any answers you have that solved your issue would be great. thanks.

Audigy platinium 4 pro and M-audio 2496

Similar Messages

Maybe you are looking for