Audigy problem with Logitech QuickCam Fusion Driv

The new Logitech QuickCam Fusion camera driver software somehow causes the 4. and 5. to get messed on my Windows XP (sp2) computer.
I spent a long time tracking the problem down including swapping out the Audigy itself, testing speakers on another computer, reinstalling creative drivers, bios, board drivers, etc. It didn't dawn on me that the Logitech driver would ever cause that kind of problem, so it was the last thing I checked.
It causes the front speaker sounds to come out the rear speakers and the rear and center channels to get whisper quiet. And, all sounds come out of all of the speakers somewhat.
Removing the QuickCam Fusion web camera driver instantly corrects the problem.
I would like to know if others who have the Audigy, Audigy 2, and X-Fi have the same problems after installing the Logitech Fusion Web Cam.
Could one of the Creative forum monitors kindly would check out this problem?
Thanks
JN

One thing you might try to see if this corects the problem is to look in your control panel, and then sound, and there have you checked to be sure that the sound card and not the Logtiech Quick Cam is the default sound device? I know that some of those devices have their own microphone and codecs and those become the default after you install them. It will make the camera the default sound device. Sometimes they even plug into your "line-in" though not always.
Cheers,
jmacguire

Similar Messages

Equium A60 doesn't work properly with Logitech Quickcam Fusion

Has anyone managed to use a Logitech Quickcam Fusion webcam with an Equium A60 ?
I've installed the latest available drivers and software and most times it just screws up the operation of the PC. It eventually hangs so badly that I can't even recover using Windows Task Manager!! If I leave the USB lead connected to the PC, 9 times out of ten, it won't boot up into Windows, until I remove the lead :(
I've installed the same software and drivers on my Desktop PC and the camera works fine every time and boots OK with the camera connected to a USB port.
Both PCs are using Win XP with SP2 and all released updates.

Hello Bill
Do you have problems with USB ports if you use other devices? I really don?t know what the problem can be. Check Logitech SUPPORT PAGE
Maybe you will find some advice there.

Problem with Logitec QuickCam Fusion...

I picked one up today. I tried to connect it to an Intel Mini running 10.4.9. When I plug it in, nothing happens. I open iChat and it says no camera connected. When I go to "more info" in the "about this mac" section, it says a USB device is connected. What do I do?

Hi adub28,
Welcome to the Apple Discussions
Did the box say this camera was UVC (USB Video Class) compliant ?
If not you will need an Add-On called iChatUSBCam
And the Mac drivers for it.
11:44 AM Monday; July 16, 2007

JMF crashed with Logitech QuickCam Pro for Notebook using latest driver.

JMF crashed with Logitech QuickCam Pro for Notebook using latest driver
I can't register the webcam in JMF. WinXP crashed with Blue-screen-of-dead.
The crash occurs on installation of JMF when the installer tries to detect my capture devices.
Windows also crashes when i open the JMF Registry Editor and tell it to search for my capture devices.
I use a QuickCam Pro for Notenooks with driver version 11.80.1065.0000 on Windows XP with JMF 2.1.1e.
PS: I can use JMF to connect to other brand's webcam.
So, how to solve it?

So, how to solve it?JMF apparently doesn't work with that camera...so if you want to install JMF, you should unplug your Logitech cam. If that doesn't work, uninstall it.

Logitech Quickcam Fusion

Hi, I'm new to the boards. I just bought the Logitech quickcam Fusion (new uvc compliant). I have a new mac pro running 10.4.10. I tried using ichat but it would not recognize the microphone on the camera. Only have options for line in and digital in. Frustrated, I plugged the camera into my Powerbook G4 (running 10.4.9) and it worked perfectly with ichat. Any ideas on why Mac Pro won't recognize the mic? Kind of frustrating since this is the cam Apple sells on the store. Thanks in advance!

This is crap ... they should patch 10.4.10 to fix the microphone problem ... I have a quickcam ultra vision and the mic of course does not work since upgrading the OS.
I hav eto use my headset for it to work. Its bad enough that apple does not work with Logitech on the drivers since canceling the production on the iSight .... but to not patch a major USB bug is simply unforgivable.
In general I have loved my switch to Mac from PC over the past year ... but this is the kind of issue I feared would haunt my decision.
D

IMac Retina 5k Display with 6 TB Fusion Drive

For no good reason Apple offers no BTO option for build-in state of the art 6 TB hard drives as Fusion Drives in the Apple Online Store. Those drives work as Fusion Drive without any problem in customized iMacs already. I have seen it! So why leave out this option? Is there any way to get a BTO Retina iMac with 6 TB Fusion Drive? Maybe a premium reseller?

Were you able to resolve this? I have the same issue and the marks look almost exactly the same...
Called Apple Care and they told me to take it in to an Apple Store, which I'll do after I backup everything.

Problem with Installer and DVD drive

I am having problems with my dvd combo drive reading discs. It keeps spitting them out. More importantly, I am trying to load Adobe Illustrator CS2 and cannot get all the wat through the installation proccess. Is there a patch I am not aware of??

You could be looking at some kind of driver corruption issue (say if that sector on your hd had gone bad, or the file was dorked somehow). Have you done repaired permissions on the hd recently?
Do all types of DVDs fail -- music, movies, and apps? If some work and others do not, then it could be a problem with a particular app.
It never hurts to check the cables. Insufficient data or power can cause all kinds of problems.
HTH,
~FifthWheel

I refurbished my macbook air 7 months ago because there was a problem with the steady state drive. Now my battery seems to be dead again. How long does the warranty last? Do I need to pay for a new battery?

I refurbished my macbook air 7 months ago because there was a problem with the steady state drive. Now my battery seems to be dead again. How long does the warranty last? Do I need to pay for a new battery?

As I wrote Apple will diagnose an Apple product even if it is out of warranty for free. That should be your first step to find out if the problem is the battery or something else.
Once you have Apple telling you a 7 month old battery is defective (if that turns out to be the case) then it becomes a game of horse trading. You'll need to speak to the tech and when he tells you there is nothing he can do you will need to speak to the tech manager and when she says most likely there is nothing they can do you go to the store manager, etc. It is unlikely (though possible) that they will give in easily you need to be firm, polite and let on that you're willing to accept a partial reimbursement.
So again the first step is to find out what is wrong.
good luck

Problems with Elitebook 8460p graphics driver

Hello
I´m having problems with Elitebook 8460p display driver. The last version (15.28.20.64.3347) posted on 16 jun 2014 have some issues on the laptop. When the notebook is running on batteries the screen suffers from flickering and corrupted graphics, as you can see in this video:
https://www.youtube.com/watch?v=gQ1w0aOaF7A
(you can see the flickering between 0:20-0:22)
I contacted with local hp support and send me an IT guy, who changed my mainboard and CPU, but nothing worked. I tried to contact with intel for support (the issue is present with intel non-oem drivers) but they send me to OEM. I would like to have an actual driver that works with the system (3347 is a year old driver), is this possible?
This issue isn´t present at all in linux drivers, plus mainboard change i totally discard a hardware problem.
I can provide feedback for any solution provided.
Thanks!

Hello @falken2k5
To get your issue more exposure I would suggest posting it in the commercial forums since the Elitebook 8460p is a commercial product. You can do this here Notebook - HP ProBook, EliteBook, Compaq, Slate/Tablet PC, Armada, LTE
The support page for your product may be helpful in the meantime: HP EliteBook 8460p Base Model Notebook PC.
I hope this helps!
Thank you for posting on the HP Forums.
Malygris1
I work on behalf of HP
Please click Accept as Solution if you feel my post solved your issue, it will help others find the solution.
Click Kudos Thumbs Up on the right to say “Thanks” for helping!

Are you having problems with the Lacie external drive after upgrading to the new operating system

Are you having problems with the Lacie external drive after upgrading to OS X Mavericks?

See here for everyone discussing the issue you are having:
https://discussions.apple.com/thread/5475136?tstart=0

Sometimes cannot start PC: problem with Hitachi SATA Hard drive and K7N2G-ILSR

I have major problem with my 160Gb SATA Hitachi hard drive and my MSI K7N2G-ILSR motherboard. Sometimes the PC can be started, sometimes it cannot.
After I installed a clean build of Windows XP Pro SP1 onto my new hard drive (as the only hard drive in my PC) and install all the necessary drivers, the system runs smoothly. However, after about 2 to 3 weeks, sometimes when I start the PC, it cannot detect the hard drive and hence it claimes that it cannot find any VMI Pool Data (i.e. no OS detected). What makes it really horrible is that, it is like the lottery everytime when I start the PC. Sometimes it works, sometimes it doesn't. The highest record was 8 consecutive failures (by resetting or by turning the power off and on again) before I can start the machine properly. Also, the system sometimes just crashes in the middle of operating.
I have already sent the hard drive back to Hitachi. Got the same model of hard drive back as replacement, but the replacement has the same problem, except with the replacement drive the PC can be started eventually after many tries, while with the previous drive it is possible that the PC cannot be started until after a few days later.
Also, it seems that my drive can detect either SATA hard drive or PATA hard drive, but not both. (If I leave my old PATA drive connect in the primary IDE channel, Windows cannot detect the new SATA drive.)
Is my motherboard faulty? Can it only use PATA drive?
My PC's spec is as follows:
AMD Athlon XP 2500+
512Mb PC3200 SDRAM (set to run at 166MHz)
Hitachi 160Gb SATA Hard drive on 1st SATA channel (Model #HDS722516VLSA80)
Sony DVD+-RW drive and Panasonic DVD-ROM drive on secondary IDE channel
Use onboard video (GeForce MX)
US Robotech V92 internal PCI modem
SoundBlaster Audigy 2 Player soundcard
Onboard audio disabled
300W PSU
OS is Windows XP Pro SP1 (with all latest security patches up to date)

Quote
Originally posted by Raven_
Quote
Originally posted by boucher91
Along the same lines the sata drives use more power than the pata drives...
sata usually faster spin rate, pata is slower spin rate...
that is not entirly correct.
many harddrives just come with different ways to connect them.
the only sata drives i now that spins faster is western digital raptors 10k rpm.
all other is running at 7200rpm.
older drives run at 5400rpm
Yes to get the full benefit of RAID, the Raptors are the way to go.Anything else, no significant difference.

Since last update, sound on my Logitech Quickcam fusion stopped working?

In iChat ,I noticed that since the last apple software update the sound on my Quickcam Fusion stopped working only the video works.. I noticed that under preferences, video, then microphone, it is no longer listed as a USB device option. Only line-in is present.
I suspect it has something to do with the last software update from Apple. I think the details had mentioned that they changed something with USB security??
I would like this camera to work since I just bought it and it was working 2 weeks ago!
Thanks for any help.
Mini Mac OS X (10.4.10) latest version of iChat AV

New Audio Update toady for me.
Although this was on my MacBook Pro that I have just reinstalled the OS on.
(I can not find it in downloads. Strangely it has appeared after the 10.4.10 combo Update)
It may also pay to start up GarageBand odd as it sounds.
Also go to Applications/Utilities and open the MIDI Utility and make sure the setting is set to 44100
10:06 PM Monday; July 2, 2007

Unable to install Windows on an 2010 iMac with home-made Fusion Drive

Hi there,
I've been very happy using mi iMac eversince I installed the SSD alongside the HDD. Only recently I tried to install Windows 7 but it doesn't seem to work. The installer runs, it seems as though Windows is installing but it doesn't ever seem to be able to boot. I've tried countless times. Everytime it boots to Windows it shows nothing but just a black screen with the cursor blinking at the top left corner.
Now, when I home-made the Fusion Drive the Mac OS was only 10.8.2 or older and I know that with 10.8.3 Apple has made improvements towards boot camp and especially the 3TB HDDs. I wonder if this could have anything to do.
Anyway, please enlighten me as to what is it that I need to do to make it work. I've been reading something about the position in which the Windows partition resides compared to GUID and EFI but honestly I have just the tiniest idea about all that. Just for the record, the following is what shows in the Terminal after diskutil list command:
diskutil list
/dev/disk0
   #:                       TYPE NAME                    SIZE       IDENTIFIER
   0:      GUID_partition_scheme                        *256.1 GB   disk0
   1:                        EFI                         209.7 MB   disk0s1
   2:          Apple_CoreStorage                         255.7 GB   disk0s2
   3:                 Apple_Boot Boot OS X               134.2 MB   disk0s3
/dev/disk1
   #:                       TYPE NAME                    SIZE       IDENTIFIER
   0:      GUID_partition_scheme                        *1.0 TB     disk1
   1:                        EFI                         209.7 MB   disk1s1
   2:          Apple_CoreStorage                         942.3 GB   disk1s2
   3:                 Apple_Boot Boot OS X               650.0 MB   disk1s3
   4:       Microsoft Basic Data                         57.0 GB    disk1s4
/dev/disk2
   #:                       TYPE NAME                    SIZE       IDENTIFIER
   0:                  Apple_HFS Fusion Drive           *1.2 TB     disk2
Hope you can help..!

Hello again, by reading a couple of posts I learnt the steps and so, using an external OS I repartitioned the two internal drives making sure the Windows partition wasn't part of the Fusion Drive. I was very excited as I was sure it would work and went ahead and started the Win7 installation even before the MacOS was restored into the iMac.
No good news though. The installer run as expected however, when the time came for the iMac to boot from the newly installed Windows7, all I saw was a blank screen and a blinking dash at the top left corner of the screen.
Lastly, this morning I woke up to see that my old system was fully restored from Time Machine external back up. I also leart that using the Boot Camp Assistant I could remove the Windows partition that I created on Terminal from the external OS, which was surprising, I honestly thought that that partitioning arrangement would be off-limits for the Boot Camp Assistant.
Still, I haven't been succesfull installing Windows back to my Mac, can anybody help?

Problems with iomega External Hard Drive on MacBook Air

Hi community!
I'm experiencing some problems with my MacBook Air and an external hard drive and I'm wondering if anybody would be able to help me out.
I own a MacBook Air running Mac OS X 10.7.3. When I connect my iomega 500GB external hard drive, the Finder is able to pick it up, but when I click on the drive name, it spins forever without the Finder responding for a long time (it basically crashes the Finder with a spinning ball staying forever). The light on the external hard drive flashes intermittently when I first plug it in, but after that stays constantly lit. So I guess the disk has power, but something else is wrong with it.
It was working fine earlier today but I accidentally pulled the cable out while the disk was working. I'm hoping this hasn't permanently damaged my drive.
Any help on what I could do to fix this issue would be greatly appreciated. Thanks!
SV

You might try launching Disk Utility, and then select the drive in question to run a "Verify disk" on the drive. This may indicate any errors in the file system of the drive that might be preventing the successful reading of the disk.
If the disk is empty, you may want to re-partition and reformat, so as to start with a "clean slate".

Problems with Monitor after Hard Drive Replacement

I never had any problems with my iBook G4 until the past 6 months. I sent it in once because it wouldn't start up. They were able to fix the problem without replacing the hard drive. It malfunctioned again and the second time they had to replace the hard drive. I've had it back for about a month and 1/2 now and for the past three weeks, whenever I try to use it I get problems with my monitor. I'm not sure if the video card is going out or what? The image on the screen gets chopped up in horizontal and vertical line increments. Its really hard to explain but sometimes it comes in waves and I have to shut down my computer and walk away from it. Other times like right now, I'm able to use it for up to an hour but then it gets choppy again and I can't use it. My Apple Care Protection Plan expires in December and I want to get as much from it as I possibly can before I have to replace the laptop altogether.

sorry,
to clarify, "internal or external;" display
internal = ibook display
external = display connected via display adaptor
Ok, well I max out the graphics on my ibook on regular intervals (games, high-end graphics work, gigabyte photoshop files etc...)
It isn't likely to be the hardware, so here's some suggestions.
LOOSE WIRES/CABLES:
The ibook's internal monitor connects through the central pivot where the ibook opens, the wires in here may be damaged. (you can't fix this yourself, refer it to apple) this could pertain to a loose or defective cable is you are using and apple display connector also.
REFRESH RATE: (this sound like your problem)
to quote a source:
"If the refresh rate is not properly set the monitor may have a wavy or an appearance that lines are going down or across the monitor slowly or fast. This may also cause a flickering affect."
http://www.computerhope.com/issues/ch000242.htm#02
This is set in display preferences. try setting your monitor's refresh rate. (75hz is good)
INTERFERANCE:
Monitors are succeptible to electromagnetic interferance: Speakers, hard drives, phones etc. try moving them away from the monitor.
BAD MONITOR:
finally; and we hope this isn't the problem. if you are not already doing so, connect an external monitor to the ibook using the display connector (VGA only), if the issue persists with the external monitor the problem is software based, if not you probably have once of a small percentage of monitors that just goes "bad" after a time period, unfortunately it's often cheaper to replace an entire unit as opposed to the screen itself (new computer)
Message was edited by: Peter Miller

Audigy problem with Logitech QuickCam Fusion Driv

Similar Messages

Maybe you are looking for