Audigy Value and Windows Vista 64-b

can any one get me this drivers can not find it in the database

Should have looked in the Vista section,?http://forums.creative.com/creativel...essage.id=8972

Similar Messages

Creative Audigy 2 and Windows Vista: Sound volume turns down when I try to turn it

I have a strange problem with my audio in Vista. I have a Creative Audigy 2 and Creative 6700 speakers. My full system specification is below but please note I did not have this issue in my previous Vista build - its only happening since I did a reinstall. Anyway, when I swich on the speakers using the remote control unit for the 6700 speakers the sound comes on but then it turns down. I have to then increase the volume by a large amount for it to start playing sound again and then turn it down to listening volume. This issue is not application specific - it happens in everything: Winamp, WMP, games, etc etc?I'm using [color="#000000"]Creative Sound Blaster Audigy series Vista Driver 2.2.0002 and I've tried reinstall several times. I've tried doing diagnostic startup etc using msconfig in case something was conflicting and its still happening.
Has anyone got any ideas whats going on?Many thanks for your help!?System specifications:?MSI K8N SLI (MS-785 v..0) nForce4 Rev. A3
BIOS Phoenix Technologies 6.00PG
AMD FX-60 with Thermalright Ultra-20 Heatsink &?Scythe?20mm fan
Bus speed: 20MHz, Multiplier: x.0, Core Speed: 22 MHz
Corsair 2Gb: 2x Gb PC3200 RAM 28 bit dual channel mode & T command rate (2.5-3-3-8) with Thermaltake heatsinks
XFX 8800 GTS 640Mb XXX Edition
Hauppauge Nova T-500 dual tuner digital TV card
Seagate Barracuda 7200.9 500Gb
Optiarc AD-770S SATA DVD Writer
Xclio X2S4P4 750WModular SLi U-Quiet PSU
Lian Li PC-A0A aluminum case
Dell E228WFP (Two in dual display)
Microsoft Wireless Laser Mouse 8000
Microsoft Digital Media Pro keyboard
Windows Vista Ultimate 32bit Edition?Message Edited by DistortedVision on 05-25-200706:4 PM

Have you checked the volume button? It might be physically stuck. To determine whether a hardware repair is needed, you need to follow these steps:
1. Try doing a hard reset:
Press and hold both the Home button and the Sleep/wake button simultaneously for about 15 seconds and release when the Apple logo appears.
After that: test the device to see whether the issue is solved.
2. If the issue is not solved, you should backup the device and restore it as new.
In that case, use: http://support.apple.com/kb/HT4137
NB: set up as a NEW device because a software issue will be in the backup.
If the issue persists after restoring as new, you should offer the device for service.
If you get specific error messages/codes in iTunes when updating/restoring, check this: http://support.apple.com/kb/ts3694 for causes and solutions
Good luck
Stijn

Audigy SE and Windows Vista Is

Hi:?In my computer, I have the SB Audigy SE card. I did a full install (not an upgrade) of Vista Ultimate in January. At this time, I had no issues with my sound. Everything worked as it should. Recently, and it is hard to specify when -- but it may have been around the time I downloaded and installed the "Vista" driver for the soundcard -- the sound on my computer got noticably lower - even when at 00%. Whereas, prior to this occurrence, when I put full power on my speakers and on the computer, the sound would result in 0/0. Now, when i put full power on my speakers and on the computer, the sound would be about a 4/0 (tops). I still hear all the sounds fine - no muddiness -- but it just is not loud (even at 00% volume).
Any suggestions?Thanks. Scott

Hi Scott! I hope you still check out this topic. I have Vista Ultimate as well. Believe the drivers that came with Vista, worked fine. I'm pretty sure they did. But with the driver as of July 09, 2007, my volume is very low. I, as well, have to turn my speakers and Windows volume up. I hope Creative can fix this problem, if possible. When I had XP, which I didn't use the July 09, 2007 driver. That driver is for XP and Vista, in one file. But there seems to be something wrong with it. It's mostly a case with Vista. I sure hope Creative reads this topic, or gets informed on it.
RR

I'm using photoshop elements 2.0 and window vista. when i want to crop i cannot enter any values in

I'm using photoshop elements 2.0 and window vista. when i want to crop i cannot enter any values in the width and height boxes. the cursor won't enter. same thing with resolution. what did i do? what's wrong?

The first thing you might try is resetting the Crop Tool by right clicking on the crop icon in the tool options bar and choosing Reset Tool.
If that doesn't work then the next thing is to reset the photoshop elements 2 settings file by holding down
the Shift+Ctrl+Alt keys just after clicking or double clicking on the pse 2 shortcut.
Keep holding the keys until a dialog appears ask if you want to delete the photoshop elements settings file
and click yes in the dialog.

Audigy 2zs Gamer and Windows Vista / Windows 7

.Audigy 2zs Gamer and Windows Vista / Windows 7? Hello, I am just wondering if it is a known issue to have really loud static and crackling when playing games using this card in Vista or Windows 7. I had this issue playing Bioshock a few months back on my Vista boot. I never figured out a way to resolve it so I belei've I just eventually uninstalled the driver and used the card without a driver install (not sure but I think this what I did). It worked but I might as well of just ran onboard sound...
Now I have installed and tried to run Windows 7 on a dual boot but I started receiving really loud cracking and popping in Warhammer Online and realized I had not installed a driver for my sound card. I did not expect creative to have a Win 7 driver yet but thought perhaps the Vista driver would work in compatibility mode, it does and sounds awesome and really makes me remember what I am missing without my driver installed on Vista but unfortunatly it randomly starts the crackling and popping again after a while...especially when a lot start happening on screen (pvp raids with many characters on screen and magic effects).
When the crackling starts happening I have no choice but to exit the game and restart the computer to get rid of the noise, but randomly it comes back after a while during gameplay. So as a temporary solution I have installed my onboard sound drivers and have been using that for sound output and my mic port on my sound card for my microphone. I would REALLY love to get my sound issues worked out in both Vista and Win 7 because it sounds SOOO awesome while it's working, the popping though is terrible, I never had that issue in XP.
I know this is an older card but any help would be appreciated!?
Message Edited by grimdeath9740 on 0-4-2009 2:3 PM@
68.95.29.2

One thing you do need to learn is that SHOUTING IS MUCH HARDER TO READ!
But, if you are using Audition 1 and it works with XP, then if you have the chance, I'd stick to that on a new machine. Apart from anything else, it's completely untried with Windows7 and with Vista its a) likely to have problems, and b) going to run slower.
The other part of your question about the 'look' of later versions is that 1.5 looks pretty similar to 1.0, but with 2.0 and 3.0 things have changed somewhat - rather more with Multitrack View than Edit View. Basic operating principle remains the same, though - most people have had very little trouble transferring from one to another.

Microphone , Audigy Se and Windows 7 64bit

*Microphone , Audigy Se and Windows 7 64bit's I have wasted several hours today trying to resolve this issue upto and including trawling the internet for a solution and completely removing and reinstalling drivers from disc and updating twice. Ultimately I downloaded an update from WIndows - Absolutely nothing, nada works!
I have the Mic Jack for my headphones plugged into the blue line in port - tried and tested on my system card (which works) but I consistently get Line--in Currently Unavailablke for this port suggesting that Creative are totally out to lunch on this one.
I have right-clicked and set levels, tried setting it as default, etc, etc, etc... nothing.
Has anyone succesfully got their mic to work uunder Win 7 64bit's
- Love how it says on the box that Vista nad WIn 7 are supported,,,? guess the partially bit was omitted!
I loathe wondows on any given day of the week but my Mac is currently down so I have no choice but to use this, my wifes machine... NOthiong but lost time whereas if I were on the mac I would be using that time producti'vely, with working software too I might add!
Hope someone has a fix for this because this machine is just one reboot away from going out the frogging window!!!

'sHi,
Are you using this driver? Are you getting no sound from your microphone or is nothing being recorded?
Please go to Control Panel, Sound make sure that the Microphone option is set as default and that the mic levels are adjusted accordingly, not mute.
If this is not working for you, Customer Support can be contacted using this http://support.creative.com/Downloads/searchdownloads.aspx?filename=

Is Verizon going to acknowlege the problems with FIOS and Windows Vista

For months now, I have been reading the numerous problems Fios internet customers are having with Fios internet/Actiontech Router and Windows Vista and there has been no acknowledgement by Verizon of this current major issue.
I have also experienced the exact same issue for months now since I switched to Verizon FIOS internet. Previously I had Comcast HSI using my Windows Vista laptop. I had their service for over a year and I NEVER has a problem with the Windows Vista globe icon disappearing and loosing internet connection. The Globe always stayed on and never went away and I never lost connection when I had Comcast
I had Verizon FIOS installed last September with my Windows Vista computer and my wireless internet connection started to drop from day 1 and it has been a daily occurrence for over 5 months now. It has gotten so bad, I have had to hardwire my laptop to to be able to use the internet uninterrupted.
This is what daily scenario is:
When I turn on my laptop(with Windows Vista, I can initially get full internet access(with the globe on and it says "Local and internet). After about 10 minutes or less, the globe switches to "local only" and I can still get internet access. After another 5 or so minutes, a large X covers the globe and I lose internet connection entirely. The actiontech router wireless signal is no longer listed as one of the wireless networks. The only way for me to regain internet access is either to restart my laptop or reboot the actiontech router.
Numeorus posts here, over by DSL forums(Broadband Reports),Microsoft's website and a few othere websites detail this issue.
I am extremely shocked and surprised that Verizon has not tried to fix this issue by working with both the makers of the Actiontech Router as well as Microsoft to find out what the problem is and how to fix it.
I would just like to reiterate I strongly believe this is primarily a FIOS internet issue since I previously had Comcast HSI for over a year with the same Windows Vista laptop and I NEVER had that problem. Also, I can connect to my neighbors wireless connection(she uses Comcast HSI) and when I do, the globe stay on all the time on my computer and the internet does not lose connection.
I know that there are a couple of Verizon employees here. Please tell the higher ups who handle FIOS internet that this is a major issue that needs to be resolved as soon as possible.
P.S: Please don't tell me to go by my own router because then, I will have to deal with the issues of setting it up to work with Fios TV and the related VOD, widgets, remote DVR compatability issues to deal with. I don't think I can deal with the additional headaches.

FIOS is short for fiber optics. fiber optics is different technology than DSL.
With that said, if you search the Microsoft databases for vista issues with fiber optics, (CURRENTLY THERE IS ONLY ONE PROVIDER OF FIBER TO THE HOUSE, that being Verizon, so yes you can also search Vista issues with verizon and\or fios) and you will find that Microsoft already acknowledges this issue with their software. AND they offer you a fix.
cjacobs001

Is there a fix for the incompatibility between itunes and Windows Vista?

I'm having a problem with itunes and Windows Vista. When I download itunes it disables my dvd drive. I have found a fix for that by deleting some registry items, but when I do that itunes is disabled. Does anyone know of a solution to this problem?

Hey Don,
What exactly happens after you install iTunes? Do you see an error message?
This article describes device filter issues that can be caused by application conflicts:
http://docs.info.apple.com/article.html?artnum=305422
Jason

Is Magic Mouse compatible with PC and Windows Vista

Hello to everyone, I'm a new member of this forum, I hope someone will help me, please.
I'm taking a look at the latest beautiful Apple's product and I felt in love with Magic Mouse, I'd like to have it for ma PC (not a Mac) with OS Vista.
Is there anyboby who knows if this mouse is compatible with a Pc and Windows Vista OS?
Actually I don't have bluetooth thecnology on my pc but if Magic Mouse were compatible I'd buy an usb adaptor.
Thanks to everyone will help e!

I asked a similar question a few hours back and no answers yet. I think nobody knows since nobody has had the chance to test them. If previous releases are any indication, you'll probably get basic functionality because it is bluetooth, but for the advanced features or setting options you'll have to wait for a Windows driver, which can sometimes take a few months or more.
My thread: http://discussions.apple.com/thread.jspa?threadID=2205313

Ipod nano first generation and windows vista

I finally got everything to work right with Itunes and Windows Vista except one minor problem.
On my ipod, the blue "dot" does not show up when a podcast is new, so in a long lists of podcasts, I can't tell which ones I already listened to.
Is there a way to fix this?
Thank you, Debra

I have a new ipod nano and can not download iTunes to Winnows Vista.
Need all the help that i can get. Thanks,
Capt g

Fieldpoint Hardware Drivers that are compatible with LV 8.5 and Windows Vista

I trying to develop in LabVIEW for some Fieldpoint hardware. I was going to download the hardware drivers from NI, but only see drivers that are compatible with Windows XP and LV 8.2
Or, am I just misinterpreting this?
Also, are there any potential conflicts with me developing on Vista, if my end-user, is uding another OS?
Daddy-O
One should welcome adversity as an opportunity to excel.

Hi Daddy-O,
Thank you for contacting National Instruments. This is a little misleading, and unfortunately the driver you are looking for is currently not directly searchable. In order to use your FieldPoint hardware with LabVIEW 8.5 and Windows Vista, you will need the FieldPoint 6.0 driver. This can be found within the disk that is distributed with new FieldPoint hardware, and any Device Drivers CD from August 2007 forward. Unfortunately, a standalone installer is not available for this driver, and if you do not have a hard copy of the Device Drivers, you can download this here. From this installer, you should be able to select FieldPoint 6.0 and install this software.
I hope this helps! Let me know if there is anything else I can clarify. Have a great day!
Jason W.
National Instruments
Applications Engineer

I set up a playlist in itunes and when i tried to sync it to my iphone i get an error message "itunes could not copy "x" to the iphone "x" because a timeout error occured. Using itunes 10.5.2.11 and Windows Vista 64

I set up a playlist in itunes and when I try so sync it to my iphone, I get an error message "itunes could not copy "x" to the iphone "x" because a timeout error occurred. Using itunes 10.5.2.11 and Windows Vista 64. Any help? Thanks in advance!

I have the same question and the only reply I've found on the forum was "change the USB hub", which HASN'T worked. So I am accepting new suggestions. Tks!

Share filing between Mac and Windows Vista

Hello,
I am trying to file share my iBook and Vista.
On my I book under Finder >>>Network>> I see my computer name "Computer-PC" but the icon is grayed out.
When I click on it it says:
The Alias "Computer-PC" Could not opened, because the original item cannot be found. Then it gives me 3 choices
Delete Alias, Fix Alias , OK
I hit OK it does nothing
I hit Fix Alias, Then it ask me to choose an item to open. I dont know what to open????
I do not want to Delete Alias.
Also I tried to connect Vista and it does see the IBook on the network, but then when I try to connect It asks for the user name and password of my iBook
I verified this by reading the support docs on the Apple website.
System Preference >>>Systems >>>Accounts >> verified and changed password.
Still no luck. Can someone give me some advice? Thanks!!

There are more than a few threads on the topic across the web; so I guess a search
would be in order and some sorting of results to enable a wise choice from them.
There's also the Apple Help built into OS X and some ideas present themselves.
Firewall changes would probably be necessary, and the Sharing (system preference)
panel has some access settings for some of this sort of thing.
(The closest I have been to sharing between a Windows machine and a Mac, is when
I let a few Windows machines mistakenly given to me to troubleshoot & repair, were
brought into my space and they temporarily shared a workbench. I found out what
was wrong with them (outside of the poor quality & shabby OS) -- and out they went!)
•Networking Mac OS X and Windows Vista - google search
http://www.google.com/search?hl=en&q=NetworkingMac+OS+X+and+WindowsVista&btnG=Search
•File Sharing between Mac OS X and Vista - google search
http://www.google.com/search?hl=en&q=FileSharing+between+Mac+OS+X+and+Vista&btnG=GoogleSearch
•Networking Windows Vista and Mac OS X - google search
http://www.google.com/search?hl=en&q=NetworkingWindows+Vista+and+Mac+OSX&btnG=Search
•File Sharing between Windows Vista and Mac OS X
http://www.google.com/search?hl=en&q=FileSharing+between+Windows+Vista+and+Mac+OS+X&btnG=GoogleSearch
edited.

HotSynch Connection gets lost between TE2 and Windows Vista

I'm trying to hotsync (by bluetooth) between my Tungsten E2 and Windows Vista. I got them speaking to each other, but the hotsync starts and never gets past the Calendar. The laptop looks like it's still running, but the TE2 hotsynch log says the connection was lost.
Is there a way to keep them connected long enough to sync?
The TE2 is running Palm OS Garnet v. 5.4.7 and HotSync v. 5.0P
The laptop is running Windows Vista 7 64 bit, HotSync Manager 7.0.2 and Palm Desktop 6.2.2.
Thanks!
Post relates to: Tungsten E2

Oh, yeah, one more thing..the hotsync works fine by USB cable on the desktop PC running Windows XP, so I don't think there's any corrupted databases on the TE2 (because if there was, then the USB cable hotsync wouldn't work)

Is there an external hard disc that will work with Mac OS10.4.11 and Windows Vista?

Is there an external hard disc that will work with both Mac (OS10.4.11) and Windows (Vista)?

For NTFS on Mac, there are both open-source and commercial solutions. See:
http://www.macupdate.com/find/mac/NTFS
For HFS+ Drivers for Windows, there is only one:
http://www.mediafour.com/products/macdrive
Regards.

Audigy Value and Windows Vista 64-b

Similar Messages

Maybe you are looking for