Audigy zs platinum sound prob

hi guys!
just upgraded to windows vista (32bit), and having huge problems with this sound card (sb0230, audigy zs platinum).
firsly I installed the complete drivers (around 65MB) from creative site and the sound was chopping/cracking/clicking (whatever that mean in english, **bleep**ty we would say here) when i would scroll an internet page or scroll text in word or scroll files in my computer.it even slows down a bit when scrolling. if you need to hear it, i'll post it to youtube.
then i installed the latest beta drivers (-35mb) and no change. then i installed the daniel k. drivers and again no change.
the onboard realtek soundcard works perfectly but has lower sound quality (too low for me).
the system is gigabyte ga73pvm-s2 with intel E6600, 2 gb ddr800 ram, nvidia 8500gt graphic card. the analog sound output (stereo) is connected to my cambridge audio 640a amplifier , not some crap desktop speakers.
while using windows xp there was not this problem. now using windows vista ultimate and have this huge problem.
please help me, what to do?

yingying,
Have you tried uninstalling it in SafeMode?

Similar Messages

Is Creative Audigy 2ZS Platinum Sound Cardcompatible with Yamaha Keyboards? (XG sound

Hi,
I have an Yamaha PSR -550 keyboard that can generate Yamaha XG sound forms in addition to General Midi. Now I want to buy a sound card that is 00% compatible with this key board so that I can connect it to computer.
Are Creative Audigy 2ZS Platinum/ Platinum pro sound cards compatible with Yamaha keyboards (especially when it comes to reproducing XG sounds)?
Thanks for your time
Vijjee

Hi,
I have an Yamaha PSR -550 keyboard that can generate Yamaha XG sound forms in addition to General Midi. Now I want to buy a sound card that is 00% compatible with this key board so that I can connect it to computer.
Are Creative Audigy 2ZS Platinum/ Platinum pro sound cards compatible with Yamaha keyboards (especially when it comes to reproducing XG sounds)?
Thanks for your time
Vijjee

Audigy 2 Platinum Weird Prob

Hi
I have recently bought an Audigy 2 Platinum soundcard. After installing the card and software I have a strange problem. When I boot up the computer I have no sound, but then if I go to the Creative Volume Control icon in my taskbar, then click on Speaker Settings, then click on Channel in the speaker test panel, I get a sound check through my speakers and adter that all sound works fine. It's a bit of a pain having to do this everytime I boot up so what is causing it not to work properly at boot up. I am running Windows XP SP2 and when I try to update my drivers from the Creative web site I get a message saying something about not being able to continue as some components are missing. Thank you.
Ian

I have an Audigy 2 Platinum running under WIN2000 sp 3., only I was getting sound at the front panel off the headphone jack, but none out the card at the back. I have tried uninstalling everything and moving the card around, changing PCI slots, and I still get sound from the front panel but not from the back. all the apps work well but only by the front. I installed Creative diagnostics and everything passes.
Could you help me
ALEX

Audigy 2 platinum eX prob

i have a audigy 2 platinum eX and my inline 2 ans makin weird noise... it only workin when i juss restarted my computer... slowly after 2 or 3 minute, the noise come, and i can use these inline anymore.
Also i cant use the headphone jack i juss cant select in the playback device.
Another thing,
my hardware is listed like (default device) to be a "SB Audigy 2 Audio [D800]"
i dont think this is normal.
i really need help
wath can i do to resolve these problem ?
(my first language is french so if u dont understanstand plz juss tell me i try to make me understand)Message Edited by bloodleak on 07-5-2005 07:20 AM

A lot of points here: first try reinserting the card, do not uninstall the drivers. Sometimes the card does not seat correctly in the PCI slot which if partially connected will cause the computer to continually verify what hardware is installed but loops off at that stage.
Take the card out (PC off) and firmly reinsert so your hear it seat fully home.
The Audigy should be in PCI slot 3.
If this does not work I think you may be looking at formatting your HDD and do a fresh install of windows. If you do decide to do this remember to install drivers in the correct order - INF chipset, windows update, video, audigy, wireless, others, rebooting twice between each.
Re which board, Intel does not boast as many features as some other boards but is more robust and everybody tests their products on a Intel board.
Re 64 bit, Creative are alpha testing 64 bit drivers now.
Re Asus should be ok, if anything Asus are suseptable to power problems.
Re RAM definitly not the problem
Re VIA not likely but possible

Audigy 2 Platinum sound problems (Windows XP S

Hi,
I recently formatted my computer and am having problems with my audigy 2 when listening to any sounds through my speakers-- headphones through the front panel sound fine! The best way to describe the sound is that it is 'fuzzy'... not an on-and-off fuzzy, but a constant fuzzy. I've tried playing with many of the options in Audio Console to no avail. Has anyone else experienced similar problems and found a solution? ANY help would be greatly appreciated... thanks!!

I found the solution that worked for me!
In the volume control for windows, I had to mute the microphone in playback mode, and check the box for 'Selected' in recording mode. To switch between the 2 modes, go to 'Properties' in the 'Options' menu. Hopefully this works for you like it did for me

K7N2 DELTA2 PLATINUM - Sound Probs, Very Strange

OK, i bought a brand new K7N2 DELTA2 PLATINUM and it works great, except from the sound which installs and in the system devices it is registered as there without yellow explanation or red cross. Is set to auto not disable in cmos.
When I try playing something it plays but no sound actually comes out. I have checked the front port switch and accourding to the manual (which was wrong over clearing the cmos, thanks guys for helping me solve that) is fine. Cab even adjust volumes in the volume control in windows.
I have tried various different drivers including the included ones and various of the internet. I have the mid Jan versions of all nforce drivers.
Everthing else on comp works fine, though if i leave the computer unplugged at mains for more than a few secs, when i switch back on the keyboard or mouse (ps/2) do not respond and all the light of the keyboard are on whether the computer is on or not. This is solved by unplugging and plugging back in mouse and keyboard.
I have also borrowed a pci card from someone and it works fine.
Please help, suggestions would be much appreciated
Note, other thing is that it is a Realtek ALC650 chip officially though something came up on a program listing system stuff that it s an ALC655; just thought i would include.

Quote from: Dr Stu on 01-February-06, 05:09:51
good idea to try knoppix
if knoppix does work, then back in windows, did you install this audio driver?
http://www.nvidia.com/object/nforce_audio_4.62_win2kxp.html
just out of interest what was your old motherboard?
It was a shite PC Chips M848A, with some c-media 5.1 audio chip.
Thanks for helping mate.

MSI K8N Neo platinum sound prob

Hi!!
I got myself a MSI K8N Neo platinum...
every 20 secondz my music hangz...
why? don't ask me.
any answers? and when my music hangs I have a look at the ctrl+alt+delete menu and I see that my cpu load goes to 46 percent when the music stops...
help...
cheerz Xyus!!

Hi!!
I got myself a MSI K8N Neo platinum...
every 20 secondz my music hangz...
why? don't ask me.
any answers? and when my music hangs I have a look at the ctrl+alt+delete menu and I see that my cpu load goes to 46 percent when the music stops...
help...
cheerz Xyus!!

Inspire P7800 connected to Audigy 2 Platinum

Help please. I properly (as far as the diagram shows) connected my new speakers to my existing Audigy 2 platinum sound card (not the front console but the sound card itself) but I do not seem to have the original sound card CD so downloaded the newest driver from Creative downloads and installed that. No matter what I do I can only get sound out of one speaker. What am I doing wrong?

There is only one choice. To get digital on the Z-5500, you have to use it's decoder (because you cannot turn it off). If you try to use the Audigy 2's decoder, you will get no sound. You can't send a decoded signal to another decoder.
In the Audigy 2 settings, select "spdif passthrough". This will disable the Audigy 2's decoder and just send the compressed digital signal to the Logitech Z-5500 control pod and it will then do the decoding (that's if you have the "coax" setting on in the control pod. Also make sure to have the DVD player software also set to "spdif" for the speaker selection.
You will be then be good to go. You can use the Z-5500 to switch between analog and digital (do not disconnect the 3 analog cables from the Audigy 2 to the Logitech Control Pod).

AUDIGY 2 PLATINUM SOFTWARE SUITE NEEDEED, ANY IDEAS PEOPLE?

I HAVE A SOUNDBLASTER AUDIGY 2 PLATINUM SOUND CARD, WHICH IS WORKING FINE EXCEPT THAT I DON'T HAVE THE SOFTWARE SO'S I CAN USE THE REMOTE CONTROL, DOES ANYONE KNOW WHAT SOFTWARE I NEED FOR THIS?

Please move your thread here: http://forums.creative.com/creativelabs/board/message?board.id=soundblaster&message.id=39573
Are you using Ventrillo or TeamSpeak?
Describe the stuff you are doing when this happends...

Audigy 2 Platinum Front jacks

I have a Audigy 2 Platinum sound card with the front panel for a mic, 394 hookup and so forth.What I need to know is what size jacks are used for the In and Out connections where you plug something external in . These are the connections to the left of the front panel.
Thanks for any help that you can give.

! Thanks KokChoy-CL
The RCA connectors you speak about are they same as the as rear connectors, 3.5 mm. If so they (3.5 mm) will not go in the front panel.Should they be real tight,I've never seen any this tight. I've had this unit since it was brought to market but, never used the in/out audio until now .We bought a wireless speaker system and I want to use the front panel as it is much easier to get to than the back.
Thanks for your help.

Audigy 2 Platinum Rem

Hey guys.
I have just recently bought the audigy 2 platinum sound card and there is something i would like to know about the remote. Once i installed the card i was playing around with the remote using all the menus and stuff and then i updated to the latest drivers on the website. Now im not sure if this has anything to do with the update but the next day i used the remote and instead of it brining up all the blue media source menus when i pressed buttons, it seemed to me mapped to windows so for example if i pressed the blue power buton on the remote, instead of it brining up the blue screen that says power off or reboot etc it bought up the turn off menu when u click start shut down in the start menu. Also when i clicked all the other buttons they were completley different to what it should be. I have since un installed my drivers and for some reason i cant seem to work out how to get it back to this. I know it mite sound stupid but i prefer the remote to be mapped to actual windows functions and not what creative has pre defined as i can change tracks with my music a lot easier when it was like this. Has anybody else discovered this or do they know how to change it to this.
Thanks for any help
Andrew

Bruskey,
You might want to make sure that MediaSource is configured in it's remote settings to have the On Screen Display (OSD) enabled. This may change what you are seeing.
Jeremy

Sound blaster audigy 2 zs platinum sound probl

Ok So let me give you the specs on my computer first,?Windows xp home editionAbit IN9 32 MAX Mobo2 Gigs corsair xms ram2 8800ultra sli gpusLogitech?z-5300 SpeakersSound blaster audigy 2 zs platinum sound card2 Samsung 500 gig HD?I dont believe that my problem is the same as is in the crackling sound thread. So here is my dilema. Up untill about 4 days ago everything was working fine with my sound system. I have the Logitech speakershooked up to my audigy 2 zs along with my xbox 360 in the optical in on the front plate. So like i said about 4 days ago i started playing a movie on my computer and i have the ac3 codec installed on my computer with comunity codec pack and i know that you could say that those 2 things could be my problem i know enough to know that that probably isnt. So when i played the movie and when to the ac3 codec and turned on dolby decoding so that i would decode it to all my speakers everything worked fine. Then when i turned on spdif decoding my center speaker?started to crackle so i figured it was just becuase i was useing spdif and dolby decoding at the same time. so i turned that off and then went to go play my xbox 360 in which i have pluged into the optical in part on the front plate. Everything had always worked fine for that i have dolby digital decodeing on for the audigy. So i started to play a game i realized that i center speaker was crackling on there too. So i started to realize that no matter what i did the center speaker was crackling. I even changed out the center and sub stereo jack on the card for the front left and right and then they started to crackle in that spot. So i dont know what the hell is going on. Any help would be greatly appreciated i was thinking of restoring my computer but i dont know whether that is necessary. I also dont want to have to go out and by the x-fi elite pro tomarrow unless I absolutely have to.Message Edited by TasteOfChaos on 0-0-20080:02 PM

I am brand new to this message system but I am so desperate for help I thought I would try it. After reading lots of comments I find that my problem may be more the rule than the exception. I have an Audigy @ Platinum card and all I ever get from it is crackling and popping. I have been around and around with Creative support but nothing they tell me results in a fix. I am so disgusted at this point that I am ready to just trash the whole thing. I have gone through the BIOS and checked so many settings its a shame. Still crackling and popping. I NEED SPECIFIC ANSWERS FROM SOMEBODY...not just the generic flip the wingle wangle to port xyz and move this to that. here has got to be an answer to this maddening problem. The other thing is that now I can't get my MIDI keyboard to play back. I must have turned something off in the set up process but now I have no idea what to do.
If anyone has any solid answers for me PLEASE come forward with them before I kill someone!

Audigy 2 Platinum prob

Hello,?Upon uninstalling the Bioshock demo today I noticed that my headphones were no longer functioning out of the Audigy 2 front port. I checked the volume and headphones, both those were working properly and nothing was muted. I can hear the sound out of my speakers normally. Additionally, if I now click on Surround Mixer I get "unable to change the sound device to your selected device."? I tinkered around a bit in device manager but did not find precisely what I was looking for evidentally to fix the issue. All the sound devices were set to Audigy 2, and that is where I get stuck!?Any advice as to where to look would be helpful.Message Edited by Platinumstorm on 08-22-2007:3 PM
Update*
I've been able to get to the surround mixer by reinstalling the drivers, but being able to get the headphones to work through the device still isn't happening... If anyone has any advice i'd appreciate it =D.
Message Edited by Platinumstorm on 08-22-2007:35 PM

I have the same problem with my SB Audigy 2 Platinum!!! --->I report here this post:
Problems with zs platinum pro 
cjsieben 
Newbie
Posts:
Registered: 0--2005
After doing a search and coming up with nothing, here's my problem.
I just installed my Audigy2 zs platinum pro. When I attempt to utilize audiohq I get the following error:
AudioHQ Plugins Launcher has encountered a problem and needs to close. We are sorry for the inconvenience.
Error signature
appname: ahqrun.exe AppVer: .0.6.0 ModName:ctdevu.ahq
ModVer: .6.4.0 Offset:0000ec2
The same error applies to device controls, eax controls, and the autoregister program.
I've tried uninstalling, reinstalling, updating the drivers, rolling back the drivers, I'm currently downloading SP2 and will try installing that :_( and there are no conflicts listed in the device manager.
Message Edited by Giorgio_DG on 08-03-200507:06 PM
Message Edited by Giorgio_DG on 08-03-2005 07:08 PM

Sound blaster Audigy 2zs platinum setup with creative inspire 5.1 digital 5

what should the setup be for the sound blaster Audigy 2zs platinum and the reati've inspire 5. digital 5500 because with the decoder in i only get center fl fr on games. i dont get sound from the rear speakers.but when i take the decoder out and just plug the 3 leads straight into the back of my sound card i get 5. any help plz.i done a thx sound test with the decoder in it does fl i can hear it but i can hear the center as well
and no sound comes out on the 2 rear speakers when doing the test.but when puting the 3 cables straight into the back of the sound card i runed the test and i could hear all the speakers fine even the rear speakers any help plz is this ment 2 happen or do i have to change some settings thanks for any help plz help me thanks.

I Have had a problem for ages. I have the Audigy 2 ZS Platinum and Inspire 5. digital 5500.
I have copied the advice I received/didnt recieve from creative.
Best of luck
Dear Martin
Thanks for your reply
I am sorry for the problem you are facing.
To achieve outputs from all the speaker during speaker test, you will need to have an analog connection, or digital DIN connection.
That will be possible if you connect the three line out jacks on your soundcard, to the three audio input (analog jacks->green,black,orange) on your speaker, if it has this connection. Or, you may connect them using Digital DIN, if they have this connection.
If you are using digital connection (coaxial, optical), there will be no way to achieve sound output from all the speakers during 5. speaker test, as they carry stereo signal.
Best Regards
(Mod Note: Name Removed)
Creative Customer Support Services
Creative Labs Europe:
Original Message Follows:
Hi
I understand you must be busy, so no problem.
No I do not hear EAX when in Pro-logic mode. I only hear (depending on the game in question)
Half life two: front left-right and centre. NO rears
Fear: Front, left, right, & centre. No rears
Farcry Front left, right & centre. No Rears
When I run your speaker test HISSSSS, No Rears, no front left or right
Beats me?
Regards
Martin
-----Original Message-----
From: CLE Customer Support [[email][email protected]]mailto:[email protected][/url]]
Sent: 24 January 2006 5:44
To: Martin
Dear Martin
I apologize for the delay on the answer.
If you select Dolby Prologic mode on the decoder, are you able to listen
the game audio, with EAX, in all of the speakers?
Regarding to the optional bay dri've, you can purchase it from ou
Best Regards
(Mod Note: Name Removed)
Original Message Follows:
Hello
Your email was helpful, unfortunately, not for my unit, you see I would
have
connected the Jack leads in by now if the inspire had Jack lead inputs
as
you describe
Please don't think I am being sarcastic, but from reading the
correspondence
below it would seem as if your department is having difficulty
understanding
my problem.
Also it would seem your department doesn't have the necessary technical
information on your very own product, so to help with your dilemma I
have
taken photos of the input/outputs on the Inspire unit.
You will clearly see the inspire has no inputs other than Coaxial and
Optic.
This leaves me back to my last post. I think the solution would be for
me to
purchase the correct processor, which would have come with the original
sound card had I not been a little tight on the money front.
I have attached a photo of the sound card with the processor, I would
love
to buy this processor but find myself unable to locate this product on
your
web site. Would you possibly be able to send me the correct link to this
item so I can buy this Processor Please?
Kind regards
Martin
-----Original Message-----
From: CLE Customer Support [[email][email protected]]mailto:[email protected][/url]]
Sent: 8 January 2006 0:3
To: Martin
Subject: RE: CLE -
Dear Martin
Thanks for your reply
Your soundcard is Audigy 2 ZS
Your speaker is Creative Inspire 5. Digital 5500
You will need to have a 3:3 cable(with the color green, black, orange)
to connect your soundcard to your speaker, to achieve the 5. effects
with games.
Below is the connection:
- Connect line out jack of Audigy 2 ZS
to 'Front' of Creative Inspire 5. Digital 5500 using the green color
connection
- Connect line out 2 jack of Audigy 2 ZS
to 'Rear' of Creative Inspire 5. Digital 5500 using the black color
connection
- Connect line out 3 jack of Audigy 2 ZS
to 'Center/Subwoofer' of Creative Inspire 5. Digital 5500 using the
orange color connection
Once you have done the correct connection, play the game DOOM3.
Ensure you have selected either the EAX or surround option in the game
settings.
Does it work?
Best Regards
(Mod Note: Name Removed)
Creative Customer Support Services
Creative Labs Europe
Original Message Follows:
You have lost me. Your sound card clearly states that I can have EAX
surround decoding from the sound card I have purchased.
All of the games on your web site claim to give me an environmental
effect
that will blow my mind, hence EAX.
All I have done wrong is NOT buying your decoder that comes with the
sound
card. My mistake.
All I want to do is re-address this issue and buy the correct
decoder/processor.
Can you point me to the correct link on your web site so I can buy the
correct decoder/processor?
As for the PCM out of the above cables, this foxes me as my other
equipment
only use Optical cabling on my Lexicon processor and from that I have DD
7., DTS 7. and meridian 5. lossless.
My issue is more to do with NO EAX from the rear and centre channels
while
in-game.
Kind regards
Martin
-----Original Message-----
From: CLE Customer Support [[email][email protected]]mailto:[email protected][/url]]
Sent: 6 January 2006 09:3
To: Martin
Subject: RE: CLE - Technical Support Request (KMM887805I6636L0KM)
Dear Martin
Thanks for your reply
All commercial digital connection eg. optical or coaxial cable will only
carry PCM stereo signal. If you want to output the signal to a surround
5. with extra EAX environment effects, it will not be possible at all
since it is only restricted to stereo channel signal.
As per current industry limitations, we are bound to follow the standard
one-signal output for all our SPDIF and Optical output jacks. This is
something that is currently shared by all vendors for all products.
Please note that all games are not dolby digital, even they are , it
will require certain motherboard to encode it to dolby digital signal,
which our soundcard does not support.
You can only use analog connections to gain true 5. surround for
gaming..
email.
Best Regards
(Mod Note: Name Removed)
Creative Customer Support Services
Creative Labs Europe
Original Message Follows:
Hi Joong
I don't fully understand your email, but I do get the gist of what
you're
saying and understand I need to connect the analogue cable to fully
appreciate the sound in EAX.
Would you be able to tell me what product I could buy from your
catalogue
which would marry up with the sound card I have, as I understand now
that
the Inspire 5. will not do the job.
Kind regards
Martin
-----Original Message-----
From: CLE Customer Support [[email][email protected]]mailto:[email protected][/url]]
Sent: 6 January 2006 04:00
To: Martin
Subject: RE: CLE - Technical Support Request (KMM8875697I6636L0KM)
Dear Martin
Thank you for the reply.
Computer games written with support for 3D audio do not require a Dolby
Digital Interacti've Content Encoder (DICE) to output multichannel sound,
with no exceptions. Sound devices that support the real time encoder
technology from Dolby will simply receive the multichannel wave file
output and encode it in real time to a somewhat modified Dolby Digital
bitstream. Creative does not support the Dolby Digital Interacti've
Content Encoder on any of its sound cards.
The only difference between a Sound Blaster card and an audio card that
has a real time encoder, is that you can make a one-wire, digital
connection from your audio card to your home theater receiver and enjoy
discrete multichannel sound from the game. However there will be a
continuous, slight delay, known as "latency", as the encoder is creating
and transmitting the bitstream, and of course the compression scheme
being used is "lossy" (i.e. not bit-accurate).
If you want to enjoy 3D audio in 3D enabled PC games in multichannel
surround sound with a Sound Blaster card, it is recommended that you
connect the analog outputs of the sound card directly to the analog
inputs of the receiver. This will require 3 cables for 5. surround
sound, one for front right and left, one for rear left and right, and
another one for front center and subwoofer. Though it requires more
cables than a real time encoder system, it will not have any latency
issues. When connecting PC audio to a home theater receiver, Creative's
latest sound cards such as Sound Blaster Audigy, Sound Blaster Audigy 2
are likely to provide higher quality audio than any Dolby Digital real
time encode system available for the PC today.
Please retain all the previous correspondence when replying to this
email.
Best Regards
(Mod Note: Name Removed)
Creative Customer Support Services
Please do not use this link to submit technical queries
Original Message Follows:
Hi
One particular game which has "in-game" DD is Farcry; I used this as my
benchmark disc for DD and to push my Nvidia 7800 GTX GPU's (I have tried
it
on friend's machines and they get the full surround effect so I Know
this
version is ok. I also have ALL of the game patches & updates.
I would like to point out that while playing Doom 3, Half Life 2,Fear,
Colin
McRae rally 04,FIFA 2004,Meddle of honour pacific assault, Rome, Shadow
ops, All these games have EAX HD, which is enabled within the options
menu
"in-game", But I do not get ANY use out of the rear's and I might as
well
listen in stereo.
No, inspire 5500 does not automatically switch while "in-game" when DD
is present as you would expect, but does if it was a Movie, which makes
me
think the DD stream isn't getting to the processor.
I originally thought I could put all this to rest if I could buy the
control
panel that would have come with the Sound card if I had not tried to
save
money, but every time I search your accessories site I get completely
lost,
it really isn't user friendly, the sub-menus are very time consuming and
point you in the wrong direction because they are not categorised as Joe
public would understand
I downloaded your TEST Movies and creative demo player utility, ran it
but
still no EAX HD or DD if that were present.
I want to put this card and Processor into my boys computer (which is
the
same Spec as mine and I will update to the FX series, but I am unwilling
if
I cannot find a logical reason why this set-up cannot work first.
Would it have anything to do with the pins on the Digital out on the
sound
card plug, the one I bought and was attached to the last email? Only
sending
certain channels down to the processor?
Regards
Martin
-----Original Message-----
From: CLE Customer Support [[email][email protected]]mailto:[email protected][/url]]
Sent: 5 January 2006 08:09
To: Martin
Subject: RE: CLE - Technical Support Request (KMM8868993I6636L0KM)
Dear Martin
Thanks for your reply
Your speakers are fine as you mentioned that there is sound from all the
speakers when you are playing movie.
May i know what game are you playing when there are no sound from the
rear speakers?
Have you done the appropriate settings in the game to achieve the 5.
sound?
Is there any game patches that you will need to update?
Does the Dolby Digital LED light up when you are playing the game?
Please retain all the previous correspondence when replying to this
email.
Best Regards
(Mod Note: Name Removed)
Creative Customer Support Servic
Original Message Follows:
Hi
I am sorry; I should have said the Inspire 5. was model number digital
5500
S/N SW330030026.
The inspire has these connection on the back of the processor
>From top/back of unit
Audio Outputs
Front
Rear
Centre/subwoofer
Audio inputs
Audio line in
Coaxial
Optical
DIN
The Din to a remotely located Subwoofer which has the speaker leads
inputting into it. Plus power.
Attached is the creative view of the controls menu and I have attached
the
invoice I was sent, it shows the lead I was told to fit.
As I said, I can now hear DD5. while within a movie from ALL speakers
BUT
no sound from rears during IN GAME DD5.
I do not use this PC for films only games.
Regards
Martin
If you are having a digital connection, it is normal for only get only
front left/right is you use the speaker test option.
http://us.creative.com/support/kb/article.asp?l=3&sid=4858
Speaker test only outputs from two front speakers?
You mentioned that that you are unable to get any sound from the rear
speakers when playing game right? May i know are you using a digital
connection? May i know what speaker settings have been made under
Creative Speaker settings?
Do get back to me on the above.
Thanks
Original Message Follows:
Operating System: Windows XP Professional x64 Edition
Creative Model Number: SBO 350
Computer Brand/Model: home made
Processor/CPU: AMD 64
Memory: Gig DDR 4
BIOS Type/Revision: 5. 39
System Board/Chipset: ASUS A8N-SLI Deluxe
Detailed Problem Description:
I have the above Sound card.
I also own Inspire 5. amp/processor
I Wanted to save money by connecting above sound
card to amp/processor
Connections on sound card made life very difficult
I contacted Creative for help. you told me to buy
an RCA to mini jack cord which also has other connections, from your
web site, (I tried to find
the product number for you, but your sub-menu
system is so poor I couldn't locate the RCA/mini
3.5 /to phono link for you) this cord connects
directly into the digital in, on the sound card (3.5 Mini jack) to the
coaxial input on the
inspire 5. amp/processor.
I have enabled ALL sp-diff settings and digital in
setting on every program/utility/kitchen sink and all.
I have an SP-Diff wire from DVD burner to creative
sound card, and yes its enabled and digital only
is selected.
I can play a DVD and see the inspire 5.
automatically change from Pro-logic to Dolby
digital when it See's an AC-3 stream.
when I try and play ANY game you say has EAX
,2,3,4 I cannot get any sound from my rear
speakers (see above in Dolby Digital ALL speakers
work correctly)
when I enter the set-up menu within the creative
software you supply with the sound card and select
5. speaker, digital only, test the speakers via
the white noise function, all i hear is left and
right noise. no centre, no rears.
I phoned you tech support line, the boy on the
phone didn't have much of a clue about your
product and I had to tell him what connections sit
on the inspire 5. series amp/processor.
I want to build another PC for my son, I want to
add the FX series sound card and amp, but i am not
willing to buy anything until i feel you have
helped me to solve this problem first.
please can you help, I am at the end of my tether
with this sound card.
kind regards
Martin Waite
Message Edited by Daniel-CL on 0-28-2006 :36 PM

Front I/0 panel on Sound Blaster Audigy 2 Platinum ZS not fo

The front I/0 panel on Sound Blaster Audigy 2 Platinum ZS not found by Creative Volume Control Application. Under recording sources, I can only choose from "What you hear", MIDI Synth, S/PDIF-In, CD Digital, Analog Mix (Line/CD/Aux/TAD/PC), Microphone and Wave. The option to record from anything on the front panel, (Aux-in 2, Line-in/Mic-in 2) have disappeared. I have tried re-installing the software from scratch, just installing Creative Update components and even formatting the hard-dri've and re-loading Windows but it still doesn't work!!?Does anybody have any helpful suggestions on this frustrating matter?

If you're using a dynamic microphone, the Audigy 2 ZS dri've bay has a jumper which you can change for it to support dynamic microphones instead of electret microphones. However once this is done you won't be able to use electret mics until you've changed the jumper setting back.

Audigy zs platinum sound prob

Similar Messages

Maybe you are looking for