Audigy2 Value conflicts with DigiCell & Core Cen

I just installed an Audigy2 Value on my new home built system. I have a MSI Neo4-F motherboard with GB of ram. I had the system running clean for a week when I installed the Audigy 2. Install when smooth but then Norton come up 'OFF' and I got error messages that DigiCell and CoreCenter (two MSI programs) couldn't load. I cleared up the Norton problem by removing the Creative Media Source program. I removed and reloaded both the MSI programs, but still get the error messages. They don't auto load, but will run if started later.
This problem seems to be related to the install of Creative programs. Is there a new driver, or new process I can follow to clear this up? Thanks

I think you have done about all you can do without going to 3rd party drivers, with their inherent risks. Regarding Norton you do not need to uninstall Media Source, all you need to do is turn off mediasource GO.

Similar Messages

Need Help Please: Audigy2 Value conflict with onboard sound

<SPAN class=postbody>System info: Windows XP Home Edition, 2.4 GHz IntelPent4, 52MB of RAM; DDR 200(33MHz), MSI MS-6547 (645 Ultra) motherboard. I need help! Sigh...well I am trying to put in a Soundblaster Audigy2 into my computer. I am under the impression that I have to disable and remove all onboard sound b/c it conflicts with the new sound card, ?. I currently have onboard sound ( AC97 Audio Controller ). I went to add/remove programs and removed the AC97 from there. I also went to MyComputer/Properties/Hardware/DeviceManager/Sound,Video,andGameControllers/AC97AudioContoller and deleted it. st Question: Under DeviceManager/Sound,Video,GameControllers...Do I need to remove the Legacy Audio Drivers? I know that I have to delete the rest of the drivers for AC97 and out of chance would Legacy be those drivers? I am guessing no...Also, is there anything else that I have to delete for the on board sound program to be gone? 2nd Question: I went to BIOS, and since I have windows XP home edition I think that configuration is a little different from what I read(I wont bore you with that). So, where do I go to "disable" the onboard sound in BIOS for Windows XP HomeEdition? Also, I read something about making sure the "Chip" was disabled but I could be paranoid. Do I need to worry about that? If you made it through all that text I thank you dearly. I hope that I can get some help from someone b/c I know nothing. I am afraid of making the wrong choice on BIOS and messing everything up. Thank You so Much! Ross Message Edited by RossRude3 on 04-06-2005 0:48 AM

Ross,
To fully disable teh onboard audio you would need to go into the BIOS to disable the Onboard Audio chip there. The manual with your motherboard or PC should have more detail on where exactly to find this setting, as it will differ per BIOS type. Generally it should be under a heading like Integrated Peripherals, and should be marked as the Onboard Audio chip, or AC97 Audio.
Cat

Windows 7 conflict with TSS Core Service

I upgraded to Windows 7 on an X61S and then cursor control failed in Outlook 2007 after I hit the enter key in new mail message. The solution was to disable the TSS Core Service (following help from microsoft). Now i need to find a compatible Thinkadvantage upgrade to get a upgraded TSS Core Service module. Whewre can I find that?

System info
Thinkpad X200
Windows 7 Pro 32bit OS
Affected applications
MS Word 2007
After opening an existing Word document, I can use the mouse to move the insertion point cursor to different parts of the document, to select objects and to highlight text. As soon as I type anything new anywhere in the document and push the Enter key (or just push the Enter key), the mouse can no longer be used to move the insertion point to another location in the document nor can it select text or objects. The arrow and shift keys still allow me to move around the document and select objects.
The problem seems to be caused by a bug in the Password Manager program that is included in the Lenovo Client Security Solution application.
Any official comments from Lenovo pls?

Need to Install Safari 6.0.2 on a white Intel core duo iMac. Had to throw out 6.0.3 because of conflict with required software. Downloaded wrong version that was for Mountain lion (I am running 10.7.5). It installs but won't open.

Need to Install Safari 6.0.2 on a white Intel core duo iMac. Had to throw out 6.0.3 because of conflict with required software. Downloaded wrong version that was for Mountain lion (I am running 10.7.5). It installs but won't open, says it is for Mountian Lion.
Of course I can't throw it away since I get a message it's part of the sytem. I can show package contents and throw those away, but evidently not a good idea!!

Need to Install Safari 6.0.2 on a white Intel core duo iMac. Had to throw out 6.0.3 because of conflict with required software. Downloaded wrong version that was for Mountain lion (I am running 10.7.5). It installs but won't open, says it is for Mountian Lion.
Of course I can't throw it away since I get a message it's part of the sytem. I can show package contents and throw those away, but evidently not a good idea!!

Problems with Audigy2 Value and CMS

I have an Audigy2 value sound card running on windows xp with sp2. My speakers are 4. Creative 4400. I installed the drivers that came along with the card and they work fine. The trouble is that unless I turn on CMSS 3D, I get sound only from the front left and front right speakers. Only if CMSS 3D is on does the rear channel activate.
This is very odd considering that I had a SBLi've! before this and I had no such problems with my speakers. I've tried tweaking the software but to no avail. Also tried reinstalling - but no change.
Please help.Message Edited by shadowfall on 0-06-2005 05:59 PM

You are a victim of the align to pixel grid option.
Starting in CS5 if when you chose a new document profile of web, that feature gets turned on. Select All and remove uncheck "Align to pixel grid".
Adiitonally uncheck Align New Object To Pixel Grid, so this does not come back when you draw new objects.
Now if you are working on a web image, then that option is good to have on, but work in units of pixels, and all should be better as long as you work in whol pixel numbers.

Problem with jquery slide show conflict with vertical navigation menu in Firefox & Chrome

Problem with jquery slide show conflict with vertical navigation menu in Firefox & Chrome. Works in IE. This is my first time trying to post a question - so please be kind. I am also not good with code and am finding css a real challenge after learning to design based on tables. I'm using CS5.
The "test" page with the slide show is: http://www.reardanwa.com/index-slides.html   The same page without the slide show is http://www.reardanwa.com/
I realize the images are not ideally sized - I'll fix those once I get the pages to function. Maybe I need a different slide show? I would prefer a widget that I can modify to required size & postition. Again - I'm not good at building with code from scratch.
The problem is the naviagation links that are directly next to the slide show do not work in Firefox of Chrome. They do work in IE.
I've read about using jQuery.noConflict(); code but can't figure out the correct way to use it in my case or whether that's even part of the solution. I know my code is not well organized as I have cobbled together from various sources in an attempt to format the page the way the client wants it. Also, FYI, I will eventually try to make the page work in Surreal CMS.
I've spent sevaral days over the last several weeks trying to solve sth slide show/navigation conflict - so any specific light you can shed will be much appreciated.
Thanks in advance.
<head>
<meta http-equiv="Content-Type" content="text/html; charset=utf-8" />
<title>Reardan Area Chamber of Commerce</title>
<meta name="description" content="home page for Reardan Area Chamber of Commerce" />
<meta name="keywords" content="Reardan WA, chamber of commerce" </>
<script src="scripts/jquery-1.6.min.js" type="text/javascript"></script>
<script src="scripts/jquery.cycle.all.js" type="text/javascript"> </script>
<script type="text/xml">
</script>
<style type="text/css">
                              #slideshow {
                                  padding: 10px;
                                        margin:0;
                              #slideshow-caption{
                                        padding:0;
                                        margin:0;
                              #slideshow img, #slideshow div {
                                  padding: 10px;
                                  background-color: #EEE;
                                  margin: 0;
body {
          font: 100%/1.4 Verdana, Arial, Helvetica, sans-serif;
          background: #004B8D;
          margin: 0;
          padding: 0;
          color: #000;
/* ~~ Element/tag selectors ~~ */
ul, ol, dl { /* Due to variations between browsers, it's best practices to zero padding and margin on lists. For consistency, you can either specify the amounts you want here, or on the list items (LI, DT, DD) they contain. Remember that what you do here will cascade to the .nav list unless you write a more specific selector. */
          padding: 0;
          margin: 0;
h1, h2, h3, h4, h5, h6, p {
          margin-top: 0;           /* removing the top margin gets around an issue where margins can escape from their containing div. The remaining bottom margin will hold it away from any elements that follow. */
           /* adding the padding to the sides of the elements within the divs, instead of the divs themselves, gets rid of any box model math. A nested div with side padding can also be used as an alternate method. */
.left
position:absolute;
left:0px;
.center
margin:auto;
width:95%;
.box
          position:relative;
          left:-90px;
          width:950px;
          height:350px;
          border-radius: 13px;
    -moz-border-radius: 13px;
    -webkit-border-radius: 13px;
          z-index:1000;
.slide{
    position:absolute;
a img { /* this selector removes the default blue border displayed in some browsers around an image when it is surrounded by a link */
          border: none;
/* ~~ Styling for your site's links must remain in this order - including the group of selectors that create the hover effect. ~~ */
a:link {
          color: #42413C;
          text-decoration: underline; /* unless you style your links to look extremely unique, it's best to provide underlines for quick visual identification */
a:visited {
          color: #6E6C64;
          text-decoration: underline;
a:hover, a:active, a:focus { /* this group of selectors will give a keyboard navigator the same hover experience as the person using a mouse. */
          text-decoration: none;
/* ~~this fixed width container surrounds the other divs~~ */
.container {
          width: 960px;
          min-height:900px;
          padding:5px 0px 0px 0px;
          background: #E8F8FF;
          margin: 0 auto; /* the auto value on the sides, coupled with the width, centers the layout */
/* ~~ the header is not given a width. It will extend the full width of your layout. It contains an image placeholder that should be replaced with your own linked logo ~~ */
.header {
          background: #E8F8FF;
          padding:10px 5px 0px 5px;
.sidebar1 {
          float: left;
          width: 225px;
          margin: 60px;
          color: #FFFF0D;
          background: #595FFF;
          border-radius: 13px;
    -moz-border-radius: 13px;
    -webkit-border-radius: 13px;
          padding: 5px 5px 0px 5px;
    border: 3px solid #F7F723;
    z-index:-1;
.sidebar2 {
          float: left;
          width: 275px;
          color: #FFFF0D;
          text-align: left;
          background: #595FFF;
          padding-bottom: 10px;
          border-radius: 13px;
    -moz-border-radius: 13px;
    -webkit-border-radius: 13px;
    border: 3px solid #F7F723;
    z-index:2;
.sidebar3 {
          float: left;
          width: 275px;
          color: #FFFF0D;
          text-align: left;
          background: #595FFF;
          padding-bottom: 10px;
          border-radius: 13px;
    -moz-border-radius: 13px;
    -webkit-border-radius: 13px;
    border: 3px solid #F7F723;
    z-index:3;
.content {
          padding: 0px 0px 0px 0px;
          width: 780px;
          float: left;
          background: #E8F8FF;
/* ~~ This grouped selector gives the lists in the .content area space ~~ */
.content ul, .content ol {
          padding: 0px 15px 5px 10px; /* this padding mirrors the right padding in the headings and paragraph rule above. Padding was placed on the bottom for space between other elements on the lists and on the left to create the indention. These may be adjusted as you wish. */
/* ~~ The navigation list styles (can be removed if you choose to use a premade flyout menu like Spry) ~~ */
ul.nav {
          list-style: none; /* this removes the list marker */
          border-top: 0px solid #FFFF66; /* this creates the top border for the links - all others are placed using a bottom border on the LI */
          margin-bottom: 50px; /* this creates the space between the navigation on the content below */
          font: Arial Black, Verdana, , Helvetica, sans-serif;
          font-size:1.3em;
          font-weight:bold;
          z-index:2;
ul.nav li {
          border-bottom: 0px solid #FFFF66; /* this creates the button separation */
          font: 120%/1.4 Arial Black, Verdana, , Helvetica, sans-serif;
ul.nav a, ul.nav a:visited { /* grouping these selectors makes sure that your links retain their button look even after being visited */
          padding: 3px 0px 5px 0px;
          display: block; /* this gives the link block properties causing it to fill the whole LI containing it. This causes the entire area to react to a mouse click. */
          width: 185px; /*this width makes the entire button clickable for IE6. If you don't need to support IE6, it can be removed. Calculate the proper width by subtracting the padding on this link from the width of your sidebar container. */
          text-decoration: none;
          color: #FFFF0D;
          background: #595FFF;
ul.nav a:hover, ul.nav a:active, ul.nav a:focus { /* this changes the background and text color for both mouse and keyboard navigators */
          background: #595FFF;
          font: 120%/1.4 Arial Black, Verdana, , Helvetica, sans-serif;
          color: #FFFFFF;
/* ~~ The footer ~~ */
.footer {
          padding: 10px 0;
          background: #595FFF;
          color: #FFFF0D;
          position: relative;/* this gives IE6 hasLayout to properly clear */
          clear: both; /* this clear property forces the .container to understand where the columns end and contain them */
/* ~~ miscellaneous float/clear classes ~~ */
.fltrt { /* this class can be used to float an element right in your page. The floated element must precede the element it should be next to on the page. */
          float: right;
          margin-left: 8px;
.fltlft { /* this class can be used to float an element left in your page. The floated element must precede the element it should be next to on the page. */
          float: left;
          margin-right: 8px;
.clearfloat { /* this class can be placed on a <br /> or empty div as the final element following the last floated div (within the #container) if the #footer is removed or taken out of the #container */
          clear:both;
          height:0;
          font-size: 1px;
          line-height: 0px;
-->
</style>
</head>
<body>
<div class="container">
<div class="header">
<a href="#"><img src="images/Chamber-Logo-2.gif" alt="Reardan Chamber Logo" width="187" height="163" hspace="10" vspace="5" align="top" /></a><img src="images/Reardan-Chamber-Title.gif" width="476" height="204" alt="Reardan Area Chamber of Commerce, Dedicated to Preserving and Enhancing Area Businesses" /><p></p>
<p style="color: #F00">This Site is under construction! Please pardon our dust as we create!</p>
</div>
<div class="sidebar1">
    <ul class="nav">
      <li><a href="about.html">About Us</a></li>
      <li><a href="history.html">Reardan History</a></li>
      <li><a href="activities.html">Activities</a></li>
      <li><a href="business.html">Business<br />
        Directory</a></li>
      <li><a href="about.html">Join the<br />
        Chamber</a></li>
       <li><a href="links.html">Links<br />
  <span style="font-size: 85%">Tourism</span><br />
      </a></li>
    </ul>
     </div>
<br />
<br />
<br />
<br />
<div class="box" +"slide">
<script type="text/javascript">
// BeginOAWidget_Instance_2559022: #slideshow
                           slideshowAddCaption=true;
$(window).load(function() {
$('#slideshow').cycle({
                    after:                              slideshowOnCycleAfter, //the function that is triggered after each transition
                    autostop:                              false,     // true to end slideshow after X transitions (where X == slide count)
                    fx:                                        'blindX',// name of transition effect
                    pause:                              false,     // true to enable pause on hover
                    randomizeEffects:          true, // valid when multiple effects are used; true to make the effect sequence random
                    speed:                              100, // speed of the transition (any valid fx speed value)
                    sync:                              true,     // true if in/out transitions should occur simultaneously
                    timeout:                    5000, // milliseconds between slide transitions (0 to disable auto advance)
                    fit:                              true,
                    height:                       '300px',
                    width:         '525px'   // container width (if the 'fit' option is true, the slides will be set to this width as well)
function slideshowOnCycleAfter() {
          if (slideshowAddCaption==true){
                              $('#slideshow-caption').html(this.title);
// EndOAWidget_Instance_2559022
</script>
<div id="slideshow">
    
    <img src="images/100_1537.jpeg" width="600" height="450" title="caption for image1" /> <img src="images/Parade-2011-2.jpg" width="300" height="225" title="caption for image2" /> <img src="images/100_1495.jpeg" width="600" height="450" title="caption for image3" />
    <div title="sample title"> Images for slide show will need to be re-sized to fit box to avoid distortion</div>
    <img src="images/beach4.jpg" width="200" height="200" title="caption for image4" /> <img src="images/beach5.jpg" width="200" height="200" title="caption for image5" /> </div>

<div id="slideshow-caption"></div></div>
<div class="sidebar2" "anotherClass editable"><p align="center"><strong>Chamber News</strong><br />
Local News item
<br />
Another New item</p>
<p align="center">lots of news this week<br />
    <br />
    <br />
    <br />
</p>
</div>
<div class="sidebar3" "anotherClass editable"><p align="center"><strong>Upcoming Events</strong></p>
<div align="center">    <a href="activities.html" style="color: #FFFF0D">Community wide yard sales</a><br />
    <br />
    <br />
    <br />
    <br />
</div>
</div>
<div class="content"><br />
<br />
</div>
<div class="footer">
        <p align="center"><span style="font-size: small">Reardan Area Chamber of Commerce</span><br />
          <span style="font-size: x-small">[email protected] - 509.796.2102</span><br />
        </p>
        
</div></body>
</html>

If you DO want the slideshow overlaping the navigation try the below css:
.sidebar1 {
    float: left;
    width: 225px;
    margin: 60px 0px 60px 60px;
    color: #FFFF0D;
    background: #595FFF;
    border-radius: 13px;
    -moz-border-radius: 13px;
    -webkit-border-radius: 13px;
    padding: 5px 5px 0px 5px;
    border: 3px solid #F7F723;
.box {
float: left;
margin-left:-60px;
width:700px;
height:350px;
border-radius: 13px;
-moz-border-radius: 13px;
-webkit-border-radius: 13px;

Boot failure with AMD core unlock *solved*

Before you criticize me for buying a triple core instead of a quad core, I want you to know that my situation seems to only conflict with Arch.
I have an AMD Athlon II x3. If I unlock the 4th core, Linux live CDs boot up just fine, Windows XP boots fine, Windows 7 boots fine, and as long as any OS completely boots up it runs flawlessly for hours with constant load. However, Arch will fail to boot IMMEDIATELY after unlocking cores. IIRC, the Arch setup CD also fails to boot. I have a small feeling that GRUB has something to do with it, but whenever I attempt to install GRUB2 I'm never able to boot again.
As another note, I can't seem to get IOMMU to work with Arch. With Debian based distros it works immediately, but I can't find anything on how to enable it with Arch. I get this impression that there's a lot of missing Kernel entries in Arch which are causing these CPU problems, and possibly others.
Last edited by schmidtbag (2011-09-27 16:16:30)

schmidtbag wrote:
R00KIE wrote:Not much of an idea then, get /proc/config.gz from the distros that work and the one from arch, compare them and see if you can spot what might be causing the problem. No other ideas here.
debian doesn't have that file, did you mistake it for something different?
I know some distros don't have it but I wasn't aware debian is one of them (I use arch everyday and I try to manage a few centos boxes and that's all), that is an option can be enabled/disabled when building the kernel and it can be quite useful when trying to figure out why something doesn't work (such as seeing which drivers were built and which option was selected when there are multiple choices), however I guess it might have security implications since anyone can find out which options were selected when building the running kernel and some combinations may have yet uncovered/unpublished/undisclosed security exploits.

"conflicts with the WAN IP address"

I just picked up a used AirPort Extreme N (Gigabit Ethernet) to replace my current non-Apple router, which has worked satisfactorily but lacks the ability to share disks--something I need. Using my G5 running 10.4.11, I downloaded AirPort Utility 5.4.2 to set up the new (to me) device, and did a factory reset just to clear everything out. I placed the AirPort in the network exactly where the old one had been--with its WAN port connected to the line supplied by my ISP (see below) and its three other ethernet ports connected to various clients. Then I ran into a problem:
Under the "Internet" icon of Airport Utility, I set it to Connect Using Ethernet, and Configure IPv4 using DHCP (My current router uses DHCP to provide IP addresss to both the wired and wireless devices on my network). The numbers below that are: IP address 192.168.1.12, subnet mask 255.255.255.0, and router address 192.168.1.1.
The first field of the line labeled "DNS Server(s)" defaults to 192.168.1.1, while the second field is empty, as are the fields Domain Name and DHCP Client ID. I left Ethernet WAN port on "Automatic" and put "Connection Sharing" on "Share a Public IP address," since I believe its combination of DHCP and NAT offer the best security.
The problem: When I click the "Update" button to confirm my settings, I get this message: "The DHCP range you have entered conflicts with the WAN IP address of your Apple wireless device."
Although I am unclear as to why the Internet Connection pane of the AirPort Utility lists "IP address" and "Router address" as two separate numbers (aren't they referring to the same device, the AirPort itself? How can it have two IP addresses?), I figured that I could play it safe and change the starting number to 192.168.1.13 to avoid the conflicts with 192.168.1.12.
But I still get the same error message when pressing "update." I tried changing the range to 192.168.1.50 - 192.168.1.60, and I still get the same error message. There seems to be no range that the utility will accept as non-conflicting with the "WAN IP address" of the Airport.
My ISP did not provide a visible modem as others in the past have done. The internet connection they left me simply comes out of a box on the back of the house that is connected by fiber optics to (presumably) a fiber optic line out in the street. However, this "supply line" has always worked fine with my non-Apple router and--after disconnecting the AirPort that had temporarily taken its place--is working right now as I throw this question to the forum.
Additional notes:
* Under the NAT tab, the box "Enable NAT Port Mapping Protocol" is checked, as it was by default) while "Enable default host at" is unchecked and blank.
* While I currently have wireless turned on in the AirPort, I haven't even tried wireless connectivity yet and want to make sure my wired connectivity is working first.
Thanks for any assistance.

The problem: When I click the "Update" button to confirm my settings, I get this message: "The DHCP range you have entered conflicts with the WAN IP address of your Apple wireless device."
This error message typically indicates that your 802.11n AirPort Extreme Base Station (AEBSn) is receiving a Private (as opposed to a Public IP address) on its WAN port. That could be because your ISP does not provide any device (computer or router), that is directly connected to their "box," with a Public IP address.
Your AEBSn is both a DHCP client (on the WAN-side) and a DHCP server (on the LAN-side). The Configure IPv4 is basically the on/off switch for the AEBSn's DHCP client. It's other option, PPPoE, would only be used if your ISP requires it.
One option would be to reconfigure the AEBSn as a bridge. This would disable both the AEBSn's NAT & DHCP services.
Although I am unclear as to why the Internet Connection pane of the AirPort Utility lists "IP address" and "Router address" as two separate numbers (aren't they referring to the same device, the AirPort itself? How can it have two IP addresses?
The IP address information on (actually the TCP/IP pane) is showing you the AEBSn's WAN port settings. Settings that with Configure IPv4 set to Using DHCP would come from the DHCP server upstream of it. If this server was providing Public IP addresses then the values in both the IP Address & Router Address fields would not be in any of the three valid Private IP Address ranges (10.x, 172.x, or 192.x)
Under the NAT tab, the box "Enable NAT Port Mapping Protocol" is checked, as it was by default) while "Enable default host at" is unchecked and blank.
This setting would not have anything to do with the error message that you are getting. Instead, this option is used as an on/off switch for the NAT-PMP protocol. This protocol is similar to non-AirPorts' UPnP protocol.
While I currently have wireless turned on in the AirPort, I haven't even tried wireless connectivity yet and want to make sure my wired connectivity is working first.
Both wired and wireless clients will be impacted by this until resolved. I again, suggest that you try reconfiguring the AEBSn as a bridge. (ref: AirPort Utility > Select the AEBSn > Manual Setup > Internet > Internet Connection > Connection Sharing = Off (Bridge Mode))

A key/value pair with this key already exists in the store

Hi all,
In the installation of PI components on the AS ABAP+ AS JAVA with finalization of the Java Addin the iam facing this problem :
In short it mentioning that the " A key/value pair with this key already exists in the store.", Please see below for more information....:
CJSlibModule::writeWarning_impl()
Execution of the command "/opt/java1.4/bin/java -classpath
/oracle/stage/PIDtemp/sapinst_instdir/NW04S/LM/AS-JAVA/ADDIN/ORA/CENTRAL/CI/install/sharedli
b/launcher.jar -Xmx256m -d64 com.sap.engine.offline.OfflineToolStart
com.sap.security.core.server.secstorefs.SecStoreFS
/usr/sap/PID/SYS/global/security/lib/tools/iaik_jce.jar:/usr/sap/PID/SYS/global/security/lib
/tools/iaik_jsse.jar:/usr/sap/PID/SYS/global/security/lib/tools/iaik_smime.jar:/usr/sap/PID/
SYS/global/security/lib/tools/iaik_ssl.jar:/usr/sap/PID/SYS/global/security/lib/tools/w3c_ht
tp.jar:/oracle/stage/PIDtemp/sapinst_instdir/NW04S/LM/AS-JAVA/ADDIN/ORA/CENTRAL/CI/install/l
ib:/oracle/stage/PIDtemp/sapinst_instdir/NW04S/LM/AS-JAVA/ADDIN/ORA/CENTRAL/CI/install/share
dlib:/oracle/client/10x_64/instantclient/ojdbc14.jar insert -s PID -f
/usr/sap/PID/SYS/global/security/data/SecStore.properties -k
/usr/sap/PID/SYS/global/security/data/SecStore.key admin/host/PID tern" finished with return
code 2. Output:
SAP Secure Store in the File System - Copyright (c) 2003 SAP AG
A key/value pair with this key already exists in the store.
ERROR      2007-02-15 18:35:29
           CJSlibModule::writeError_impl()
CJS-30051 Cannot insert a key value pair into the secure store fails; see output of log
file SecureStoreInsert.log:
SAP Secure Store in the File System - Copyright (c) 2003 SAP AG
A key/value pair with this key already exists in the store..
ERROR      2007-02-15 18:35:29 [iaxxgenimp.cpp:731]
           showDialog()
FCO-00011 The step insertAdminDataInSecStore with step key
|NW_Addin_CI|ind|ind|ind|ind|0|0|NW_CI_Instance|ind|ind|ind|ind|8|0|NW_CI_Instance_Configure
_Java|ind|ind|ind|ind|4|0|insertAdminDataInSecStore was executed with status ERROR

Hi Kamalakar
I think this problem happens due to wrong content of SDMKIT.JAR - incorrect crypto SDA is deployed.I dont know the installation procedure you followed because normally this error wont come.
I would rather suggest a work around seeing your problem
<b>Edit the keydb.xml exchanging [ERROR] with [OK]</b>
Follow the above step and restart your installation.
Do not forget to reward points:

MAC Adobe Illustrator CS3 cannot be installed because it conflicts with Adobe Illustrator CS3

Model Name:iMac / Processor Name:Intel Core 2 Duo / Memory:4 GB
When I installed Illustrator CS3 at the first time, I didn't complete it and closed it. While I installed it again, it said "Adobe Illustrator CS3 cannot be installed because it conflicts with Adobe Illustrator CS3". I was be stopped on this step, so I deleted the Illustrator CS3 from Applications/Utilities/Adobe Installers without clicking it to uninstall. And I deleted other Illustrator CS3 files. After that, I tried to reinstall Illustrator CS3 again, but it kept to say "Adobe Illustrator CS3 cannot be installed because it conflicts with Adobe Illustrator CS3".
I cannot find any Illustrator in my MAC. What is wrong? How can I install Illustrator again? Should I format the computer and install all the applications again?

On the Adobe site probably under support do a search for Adobe CS 3 Clean Up Script.
Before running the script read the instructions al the instructions first, do not assume you understand from reading the first sentence. There are some files that are not so obvious that are necessary for activation and they are probably still around but they can only be removed by the script.
Next time you will have to read the instructions.
The only other ways around this is the do an archival reinstall of your system or if that does not work a complete reinstall of your system. Running the script is the easier and better way to do this but you must read the instructions completely first.

[SOLVED] kdebase-workspace: conflicts with kdemod-kde-common

Hi! My pacman -Syu failed today: Here there is the output (of a retrial):
:: Synchronizing package databases...
kdemod-core is up to date
kdemod-extragear is up to date
core is up to date
extra is up to date
community is up to date
:: Starting full system upgrade...
:: Replace qtmod with kdemod-core/kdemod-kde-common? [Y/n] Y
:: Replace guidance-power-manager with extra/kdebase-workspace? [Y/n] Y
resolving dependencies...
looking for inter-conflicts...
error: unresolvable package conflicts detected
error: failed to prepare transaction (conflicting dependencies)
:: kdebase-workspace: conflicts with kdemod-kde-common
Any suggestions on how to get this update right?
Last edited by joan (2009-02-23 02:18:30)

joan wrote:Hi! My pacman -Syu failed today: Here there is the output (of a retrial):
:: Replace qtmod with kdemod-core/kdemod-kde-common? [Y/n] Y
:: Replace guidance-power-manager with extra/kdebase-workspace? [Y/n] Y
Any suggestions on how to get this update right?
Try:
pacman -Rd gtmod
pacman -S qt
#Qtmod not needed anymore
pacman -R guidance-power-manager /or pacman -Rcsn ....
pacman -Syu kdemod /or pacman -Syu kdemod-complete
also backup/ remove ~/.kde4 to start with clean config, especially if you have your own plasmoids.
#powerdevil is included in kde now, so other inferior powermanagers might conflict with it.

Audigy2 Value card corrupted my CD-Rom driv

Purchased a brand new Audigy2 Value sound card and installed it in my system (Dell Dimension 2400) along with the card's software from the CD. Earlier that day my system was working just fine and I was able to use my CD-Rom dri've and my CD-RW burner dri've as well. After I installed the new card and its software I was able to play MP3 files from my hard dri've and I was very happy with the great sound coming from my new sound card.
Later that day I wanted to play a CD to see how that sounded and that's when the trouble began... My computer no longer was able to access either of my two CD dri'ves. When I checked them out in my device manager it stated that their drivers were now either "corrupt or missing". Not hard to figure out how this occurred seeing as they functioned normally earlier that day before I installed the new Audigy2 and its software. I read the trouble shooting steps on the Creative Knowledge Base section and tried to follow the advice given for this type of problem but it was of no use. Phoned Creative support and the best the techs could suggest was to erase all of the Creative software and yank out the card and see if the dri've's come back. Didn't help. The drivers that operate the two dri'ves were still "corrupted or missing". Now my only option was to download new CD-Rom drivers from Dell.Com and try and get my CD-Rom back in action with new drivers. But... the new Dell drivers require that you copy them onto a bootable floppy disk to start the computer with so they will install properly with the system and its bios. Great, the Dimension 2400 does not come with a floppy dri've and Dell says there is no other way to install the new drivers except with a floppy disk which is hard to believe in this day and age of so many systems being sold without them. So now I can't reinstall the drivers to make my CD-Rom work and I can't use my master CD with the drivers because my CD dri've doesn't work. It's looking like I'll be purchasing a **bleep** floppy disk external just to try and get my system back to normal.
Just wanted to share this experience with other Audigy2 Value card owners or potential buyers. Great sounding card but certainly not worth this kind of trouble and pain!

if your using winxp, try the system restore feature. go back to the last restore point before you installed the creative drivers and see if that recovers your old drivers.
if that works, reinstall the creative drivers using the custom install and don't install any of the dvd stuff or any other program you don't need to run.

[SOLVED] systemd-arch-units conflicts with mdadm and xinetd packages

Trying to upgrade my testing box today to latest/greatest and running into a file conflict between systemd-arch-linux providing systemd profiles for xinetd and mdadm which also think they control the same files:
error: failed to commit transaction (conflicting files)
/usr/lib/systemd/system/mdadm.service exists in both 'mdadm' and 'systemd-arch-units'
/usr/lib/systemd/system/xinetd.service exists in both 'systemd-arch-units' and 'xinetd'
Errors occurred, no packages were upgraded.
Should I just do a force? I am not relying on systemd yet. Or should I just remove systemd?
Chester
Last edited by chetwisniewski (2012-05-15 18:17:45)

silent wrote:So now the new version of mdadm and xinetd moved to [core] and I have the same conflict with systemd-arch-units in [community].
Try -Syu again?

[IPhone SDK] NSTimer conflicts with touch events

Hi all,
i've an NSTimer that refresh the UIView at 30 fps. Below there is the scheduled timer:
animationTimer = [NSTimer scheduledTimerWithTimeInterval:animationInterval target:self selector:@selector(refreshAll) userInfo:nil repeats:YES];
The problem is that the app doesn't wrap the touch events (touchbegan, touchesMoved and touchEnded) because the timer interval is too low and conflicts with this events.
I tried to set the animation interval to 2 seconds and the touch events works but the rendering obviously is slow.
However the problem is only on the device because when i launch the app on the simulator i have no problem with the timer.
Can anyone tell me how I can solve this problem?
Thanks

The game I'm developing for the iPhone has 2 play modes (the second mode has more on screen objects). In the first game mode, I get a solid 29-30 frames per second (acceptable), however the second mode with more objects gives me 25 fps (slightly jerky). BTW, on a PC with modern hardware I get >1300 fps @1680x1050.
At first I thought that the NSTimer resolution might be causing problems. The Apple demos all use a resolution of 1/60. Setting a value of 0.0 actually bumps the frame rate up by few frames, but I lose the ability to process touch input (crap). Adding usleep(a_delta) hoping to invode a context switch does nothing for the touch input.
The next thing I tried was creating a dedicated rendering thread which basically does a while (1) render(); The thread will loop as fast as it can, and I regain touch input. On the plus side, I gained 3-4 fps for both game modes, so now I can hit 30 fps for the second mode (sweet).
To make this work, I obviously needed to add locking primitives between the render thread and the iphone input (touch, sleep, phone call etc). The render loop is now basically:
while (alive)
aLock->Lock();
render();
aLock->Unlock();
Anyway, I thought people would appretiate my experience when looking to squeeze a few more frames out of the iPhone. You just need to understand multiprocessing to work out the synchronisation issues.
PS. There is some interesting advice in the following thread:
http://discussions.apple.com/thread.jspa?messageID=7898898&#7898898
Basically, they set invoke the runloop from the animation method. This might be simpler than spawning threads and handling locking, but I haven't tried it.

SB Audigy 2 ZS Conflict with Unreal Tournamen

Hi there, I've been able to determine that my SB Audigy 2 ZS card is creating some sort of conflict with Unreal Tournament 3.When I disable the soundcard in the device manager, the game will load. Otherwise, the game will not load. I've downloaded the latest drivers for the sound card and video card, and have tried reinstalling UT3. Anyone have any Ideas where this problem is coming from ?Here are my tech specs;Intel C2D 3Ghz @333 FSBAsus Maximus Formula MBEVGA GeForce 8800 GTS 640MB2 GB Crucial Ballistix DDR2 033SB Audigy2 ZS Platinum?WD Caviar SE6 SATAII 500GBAntec Neopower 650wWindows Vista 32 bitDirectX 0?This is a link to a discussion thread I posted on the issue in the Unreal 3 Tech Support Forums;http://utforums.epicgames.com/showth...=600409&page=2?Message Edited by odin_tyralothe on 0-26-200806:49 PM

calcal wrote:
well there was a great deal for this so i took it. This is a great card and i love it but theres a problem. Id say out of 5 cold boots or restarts, my usb mouse will not work. This happened after i installed my new sound card.Message Edited by calcal on 08-3-2005 0:57 AM
I suppose, your sound card is sharing an IRQ with your USB controller.
Try moving your mouse into another USB port(s). If this don't help, you can re-install your sound card into another PCI slot (see on your motherboard manual how IRQ's are assigned for PCI slots). PCI slot 3 or 4 (count from AGP) are normally less shared.
You can check your IRQ sharing situation from device manager - device manager -> View:resources by type -> interrupt requests (IRQ)).
You can also disable controllers/devices on device manager (right_mouse_click the item you want to disable(/enable) and select disable(/enable). Do this only if selected controller/device is not needed and it is sharing an IRQ with controller/device you need.
this so far...
.jtp

Audigy2 Value conflicts with DigiCell & Core Cen

Similar Messages

Maybe you are looking for