Audio and video not synchronized in recording made with Lync 2013

There appears to be no forum for the Lync 2013 client yet, so I am posting this in the Lync 2013 server forum.
Environment: Lync 2013 Server and Lync 2013 32-bit client. Only one Lync pool. Conference call was scheduled using "Lync Meeting" in Outlook about a week before the call. Call recorded on a laptop that was plugged into our LAN with an Ethernet
cable.
Problem: User scheduled a conference call with screen sharing (PowerPoint) and recorded the call. The audio and video are not synchronized in the recording. There is several minutes' delay, with the audio lagging behind the PowerPoint. The last slide
on the call was presented, the call ended, and the presenter ended the recording (I was present for all this and can confirm no user error in these steps); however, in the recording, the slides change before the speaker talks about it, and the last
couple of minutes are cut off. 
Any ideas on why this happened? Web research has failed me. Thank you.

You may need to lower the recording quality as your PC might not be able to keep up the pace.
Go to Options in Lync client -> Recording -> Select 480p
Then test again
- Belgian Unified Communications Community : http://www.pro-lync.be - MCM/MVP/MCT

Similar Messages

  • Audio and Video Not Synchronizing in the Same Clip.

    Ok, So I have had Adobe Premier Pro for a while now an I love it. I just have one not so insignificant problem with it. I was in the middle of making a video (with one particularly long clip in it) and I noticed something that began to happen in the beginning of the clip and went up until about thirty seconds. The audio and video gradually became further and further apart until they were about three seconds off. I was only using one clip so there should be no way I screwed up the placement of the files in the timeline. Viewing the clip in quicktime player does not give me that problem, so it's either a problem with Premiere Pro, or something else that I am unaware of. It has became so bad that I even downloaded iMovie so I could at least get this movie edited. I am pretty new to Premier Pro so any advice is much appreciated. Thanks!

    Exactly what is INSIDE the video you are editing?
    Codec & Format information, with 2 links inside for you to read http://forums.adobe.com/thread/1270588
    Report back with the codec details of your file, use the programs below... A screen shot works well to SHOW people what you are doing
    http://forums.adobe.com/thread/592070?tstart=30 for screen shot instructions
    Free programs to get file information for PC/Mac http://mediaarea.net/en/MediaInfo/Download

  • Audio and Video not synchronized...what's the solution?

    Hi,
    I was trying to record a video on my webcam (I think its Creative Gamestar) and during playback I noticed that the audio is playing slower than the video; in other words both are not synchronized...what could be the reason for this? Is there a solution.
    I used the DivX 6.0 video codec. The audio compressor was MP3 at 48,000 Hz, 6 bits, Stereo. Do I need to use something other codec? Please reply! The reason I used DivX was that the default codec was creative a 2Gb file for a 5 minute video.
    Looking forward to replies. Thanks in advance,
    Badfan.

    Hi John and techkid123
    We have 4 cameras here. 1 is Sony model HD1000 (since it works with Mini-DV cassete we need to capture the image via Firewire). 2 cameras are Sony HD2000 (it generates *.MPEG files if I remember well). And 1 camera is a Panasonic AG-DVC7 (it generates *.MTS files)
    We start a new project using the Standard NTSC Widescreen 48Khz format.  When we drag to the timeline for example the MTS file...Premiere ask us if we want to Keep and Change timeline to suit the file specification. Anyway we always have 1 or 2 camera files that has a yellow line over timeline.
    But I renders correct...no problem to edit...and we had no problem with Premiere CS5.5 :/
    We are downloading the latest update of Premiere. I´ll make some test and publish here if the problem persist.
    Thank you a lot for the help
    Gustavo.

  • Audio and video not synchronized when exporting from Premiere Pro CS6

    Hi
    We have made a project in Adobe Premiere Pro CS6 that´s intended to be exported to DVD (it´s a weeding). We are working with NTSC DV Widescreen. The exporting is 720x480
    We have 2 audio lines activated and sounding on this project.
    The question is:
    When exporting the entire video (the entire timeline sequece) using Adobe Media Encoder to formats like H.264 (NTSC DV Widescreen)... Quick Tile Movie or AVI without compression (we tested these formats) the 2 audio channels get unsynchronized from the video. The same problem occurs if we get a direct link of the timeline from Premiere to Encore.
    And Inside Premiere Preview audio is preety correct.
    Does anyone here are getting such problem?
    Also..can I ask another question (as I´m not expert on video production)?. What´s the best format for our purpose? Export a video to be played to DVD (we record weedings, birthdays..social events). No problem the time to export. We´d like the best quality for output.
    Thank you for the help
    Gustavo.

    Hi John and techkid123
    We have 4 cameras here. 1 is Sony model HD1000 (since it works with Mini-DV cassete we need to capture the image via Firewire). 2 cameras are Sony HD2000 (it generates *.MPEG files if I remember well). And 1 camera is a Panasonic AG-DVC7 (it generates *.MTS files)
    We start a new project using the Standard NTSC Widescreen 48Khz format.  When we drag to the timeline for example the MTS file...Premiere ask us if we want to Keep and Change timeline to suit the file specification. Anyway we always have 1 or 2 camera files that has a yellow line over timeline.
    But I renders correct...no problem to edit...and we had no problem with Premiere CS5.5 :/
    We are downloading the latest update of Premiere. I´ll make some test and publish here if the problem persist.
    Thank you a lot for the help
    Gustavo.

  • CS3: Audio and video not synchronized

    Hello.
    I built a video, and in this video sometimes there isn't the audio track because i cut it. After i exported the video in the avi format, i noticed a big desynchronization, because the audio tracks started earlier than expected. What have i to do?
    Thanks
    Giulio

    What was the format/CODEC of your original source files?
    What is your Project/Sequence Preset?
    When you Render the Timeline and playback in PrPro, did you hear the OOS (Out Of Sync), or was it only after Export?
    What were the full settings of that Export?
    Is the OOS static (same over time), or is it dynamic (changing over time)?
    Good luck,
    Hunt
    PS - for general OOS issues, this ARTICLE might be useful.

  • Audio and video not in sync. went back to previously finished projects and they too are not in sync. What could be the problem?

    Audio and video not in sync. Went back to previously edited projects and they too are now not in sync. What could be the problem?

    Um ... some useful data?
    OS/CPU/RAM/GPU/vRAM ... version of PrPro ... and other programs or plugi-ins/3rd-party apps involved ... footage type/codec/wrapper ... such things would be very useful.
    Neil

  • Audio and video not synched up....

    Hello everyone. I am having a problem with my i-movie and was wondering if anyone here might know what I need to do to solve it.
    The problem is that the audio and video are not synchronized when I capture a movie.
    Any suggestions?

    Hello and thanks for your help. May I pursue this with you further? I think I figured out how to separate the audio and video, by using the imovie help. What i have now is a green bar that appears all along the bottom of the video frames.
    I'm having one problem. When i move the audio, and then play back the track, both the new audio position and the old one play, so I get this echo effect. Do you know how I save it without the old position?
    Also one other problem I'm having is that when I record video, for some reason whole chunks of the recording are missing. I don't know what is causing this....

  • Audio and Video not matching up after compression

    I made a video that is 3:18 minutes long and after about 2 minutes, the audio and video don't match up anymore. I have 2 clips in the video that i conformed to 24p in Cinema Tools and i think that they are causing this problem. I noticed that Audio rate of the clips that i conformed, does not match up to the clips which are not. For example, the audio rate of my 59.94 fps clips is 48.0 KHz, and the audio rate of my 24 fps clips is, 19219 KHz. Is there any solution to this problem? I read a post that said i would need to re-digitize the clips, but i don't know how to do this. Can anyone help me?

    I still can't figure out how to solve this problem. I tried to resample the audio, but still, same things happening. If you watch the video, the audio goes off about 2 minutes into it. The audio is correctly matched up with the video when i view it in FCP, but every time i compress it, audio goes off in the exact some spot. Here is a link to the video- http://vimeo.com/21619542
    Message was edited by: Gray McClamrock

  • Audio and video not in synch after upgrade

    I have 12.1.1.4. I'm using this new version for the first time tonight, to watch some Walking Dead episodes, and the audio and video drift out of synch. I can bring them back into synch by pausing then replaying, but it doesn't last. I watched some older videos that I know to be good and had the same issue, so it's not a problem with the episodes.
    What I've tried:
    Making sure that the Quicktime audio settings match the ones on my sound card.
    Uninstalling and reinstalling iTunes.

    I also have this problem, and some videos will no longer play in iTunes.
    I get a message that this video is not compatible with this version of iTunes. I have to open the video in Quicktime to watch it.
    Unacceptable! This hardware and software is too expensive to have these performance issues.
    2011 Mac Mini, 8GB RAM, Duo core, iTunes library on NAS on wired network. Mountain Lion 10.8.2. iTunes 10.7 64 bit.

  • Photo Booth Audio and Video not in sync!

    I am a YouTube musician. When I go to record I find it easiest to use the video feature in Photo Booth. However, ever since I upgraded to Mountain Lion my audio and video in my videos has been off of one another. They start off together but by the end of the video the audio is ahead of the video. When I went to try and see where it messes up I found that the video jumps frames creating almost a transition effect. I don't know how to fix this and would really like your help!

    Check out the "More Like This" threads over in the right column------------>
    Also check out KB Article http://support.apple.com/kb/HT2090 How to Troubleshoot iSight and EZJim's Website for possible solution to your problem.

  • Audio and Video not in Sync (Decklink a/v)

    Hello. No matter what I do, Soundtrack Pro's audio and video are not in sync. Audio always comes a slight bit later which makes working in STP really hard. I run STP with a Decklink Extreme, for both audio and video. Any tips?

    well i had the same post. kinda. but yeah it is totally limited as a film scoring app, who would have thought. there isn't any way to offset the sync.
    Logic would be your best bet, or Pro Tools with DV kit.
    FP

  • Home entertainment - Audio and video not in s

    I call a Philips LCD 37PFL7403D/0 with [size="">HD Natural Motion technology my own. When I turn on HD Natural Motion feature, audio and video are not in sync anymore. The Philips FAQ recommands to set the audio sync delay to 200 milliseconds (200ms).
    I use a Sound Blaster X-Fi Xtreme Audio and I have not found any possibility to adjust the audio sync delay.

    Um ... some useful data?
    OS/CPU/RAM/GPU/vRAM ... version of PrPro ... and other programs or plugi-ins/3rd-party apps involved ... footage type/codec/wrapper ... such things would be very useful.
    Neil

  • 5G iPod Audio and Video not in Sync

    I bought an iPod 30 GB a couple of days before. I was trying to download a movie to it which is in MP4 format. The original movie was in AVI format and I used Videora iPod converter to convert AVI -> MP4, but when I try to view the movie in my iPod the Audio and Video are not in Sync at al. The audio is way ahead of the video. Please someone let me know how to fix this problem. I turned off Equalizer and all other fancy settings in the iPod but it still didn't help.

    some encoders have this problem occasionally. I've seen it very frequently in ffmpex when the source is avi. not sure what you're using, but so I'd suggest you try a different software. I'm getting very good results out of handbrake or 42.

  • IChat Audio and Video not working correctly...

    Hi.
    I recently upgraded to Snow Leopard. Before upgrading, I was able to video chat with little to no problem with family over iChat. I just tried it again today for the first time since upgrading to Snow Leopard and the audio is barely working (can only make out every few words, if that), and the video is extremely distorted to where you can sometimes not even tell there are people there. It gets all pixelated and weird. I tried doing the chat with Google Talk and then again with Skype, and had just as many problems with those. My family is using a Mac with an older OS, and they can see and hear me perfectly fine. I'm not sure if the problem is with my computer or with theirs, or if it's just a communication problem, but any ideas would be really helpful. Thanks!

    After iChat developed missing audio and video pixellation problem post Snow Leopard installation at my mother-in-law's machine (and ours), I tried the usual decrease the bandwidth fix to no avail.
    The solution that actually fixed the probem was to turn off port forwarding protocol on her Time Capsule and our Airport Extreme. Things are now working smoothly even at 500 kbps settings on both ends.
    An interesting aside... Turning off port forwarding for ssh to her machine doesn't kill the ssh port tunnel from the outside LAN to her mac. It looks like iChat and the Time Capsule keep an incoming ssh tunnel open even if you have disabled port forwarding on the Time Capsule. I suspect this "secret" opening of ports is the magic of why iChat and screen sharing have been so much easier to set up when a Mac is behind an Apple router. 3rd party routers need ports manually forwarded to the Mac. Apple routers just worked ---- and it looks like Apple does it by invisibly opening ports on their routers when a Mac runs iChat.
    Pretty nifty, but also silently opens a security hole that you may THINK you closed. SL seems to trip up over this arrangement when you also turn on Port Mapping Protocol and manually assign ports to forward.
    At any rate, it wasn't the data rate, it was a new bad interaction between the Apple Router's Port Mapping Protocol and iChat 5. Turn off PMP on the airport and all becomes well once more.

  • Audio And Video Not Linked

    When I drag clips from the Viewer to the Timeline I get audio and video together, but afterwards they are separate. They aren't selected together unless I do a shift-click selection, and even then I can't trim both at once. FCE does seem to remember that they should be in sync because I still get the little red boxes. This is probably just some little setting I inadvertently changed, but I have no idea what. Can someone please help?

    eatrains
    Linked clips (video and audio) will have an underline below the name, this can be toggled on or off with Modify>Link (Command-L).
    For selecting in the Timeline there is a button at the top right. This only selects the video and audio at the same time, it does not Link/Unlink.
    Al

Maybe you are looking for

  • IMac G3 33MHz runs system 9.2.2 but crashes runing system 10

    This is a strange one. I own many macs (over 20 last count). Recently we upgraded the office to new iMacs, eMacs and G5 towers. I still have several 1999 - iMac G3 tray 333Mhz and I am in the process of finding other uses for them. I add memory and u

  • Database in Suspended Mode

    Hi, I faced this problem suddenly when i was trying some indexes on a local dummy table(using 'sa' user id) on DB COSMOS. After working around indexes i saved the file and closed Query Analyzer. On relogging again with 'sa' user Id i faced the follow

  • Can't send mail to external recipients

    When I invite a new member to a collaboration room, and this member is registered in active directory with an email adress, all invitation and notification mail work as they should. However. I want to invite external users(external to our company) in

  • Select 0 as 'Alias Name' in webi report modify screen

    in SQL you can do this: select sum(chequeamount) as ROInc_amt, 0 as Inc_amt how can you do this in a webi report though when I try it doesnt parse what is the syntax to use? BO Edge XI 3.0 App server: MS Win2003 Server Standard SP2 DB server: MS Win2

  • Document Properties time stamp

    Post Author: Hieu CA Forum: crystalreports.com The time stamp in Document Properties (such as this one "07-08-08 17:04:50.338") is based on Eastern Time Zone. Is it possible to change this to reflect my local date/time as seen on the bottom of the Cr