Audio doesn't match the video ... why

Last night I tried to sort some of the clutter from my desk by downloading some recorded video on VHS tapes. The images worked fine with no dropped frames at all, however, the audio doesn't match the video.
Example 1: the footage is of skydiving recorded from Channel 4 (UK) while the audio that is captured with is commentry from several years ago when we lived back in Australia (Channel 7).
Example 2: the audio is very very slow.
The footage was recorded on a VCR which has no audio/video out facility and is converted via the ADVC 110 from a VCR which does have the audio/video out plugs. The DV is then saved to an external drive 500GB.
Can anyone suggest a way around this unique effect .... please.
Blue skies
Dean

G'day Martin,
Here are the answers to the questions you asked.
As far as I can tell everything is PAL. The VCR used to record the footage and the VCR used to download to the converter. The later has NTSC capability but not turned on (I checked).
The Canopus is set to PAL and the FCE easy set up is set to DV PAL converter.
The Video and Audio are recorded at the same time.
I should add that I tried it again this morning and it worked for a short while but then reverted to previous reported faults. I have tried about 8 different VHS tapes and they all do either of the two described faults.
Thanks for your suggestions.

Similar Messages

I imported a video and when I play it back, the audio does not match the video. When I view the tape in my camera it looks fine. I've tried imported twice and each time it doesn't match. What can I do to fix this?

I imported a video and when I play it back, the audio does not match the video. When I view the tape in my camera it looks fine. I've tried imported twice and each time it doesn't match. What can I do to fix this?

The default settings mostly likely use an audio sample rate of 32k. This doesn't work probably in FCP. You're probably better off capturing the tape in iMovie.

Audio doesn't match video because repeated half way through

Hi guys,
I am currently editing videos from my Canon SLR with Adobe Premiere Elements (Windows).
In the same project, I have only uploaded videos taken the same day with the same equipment. I have been able to process them all normally apart from one. For some reason, when I play this file with a basic video player, everything works fine but when I import it in the Adobe software and play it either through the small window or in the timeline, I have the same problem:
Everything works fine (audio and video in sync), until it reaches a specific point (totally random as far as I can tell) when the video keeps going but suddenly the sound repeats itself from the beginning of the file (and the audio which would correspond to the video is replaced by it). For you to understand better the problem:
Video:   ABCDEF
Audio:   ABCABC
I have tried opening it in a different project and somehow it happens exactly at the same point.
I am totally clueless of what it comes from and getting really frustrated!
Any idea?
Cheers
Babs

Hello, I'm new to using forums like this. Is it appropriate for me to post that I'm having the same issue? Also sounds similar to Audio doesn't match video because repeated half way through as well.
My situation is:
Win7 64-bit, i7 920, 2.67GHz, 8GB RAM
Multiple Nikon D7000 video clips I've taken play back fine except for the following clip. In Windows Media Viewer, I have no problem, but in PE10, in the timeline editor, this clip repeats the audio from the beginning starting about 6 minutes into the video. I have Quicktime version 7.7.5 installed which I noticed was mentioned as a possible culprit in the other thread.
I've been using my camera primarily for stills, but decided to have my mom tell her story before she wasn't able to. I'm so frustrated with this problem because I know the audio is just fine since I can play it back synchronized throughout the entire clip in WMV. I've tried cleaning out PE caches as best I can figure them out and created new projects without any better luck.
Any help would be greatly appreciated. I'm open to getting a new version of PE or another program if I could believe that I wouldn't run into this issue again. This seems like such a vanilla problem since all my other clips seem to be fine and this one does too on WMV.
Thanks for any help you can provide. I don't really know where else to go to figure this out.
Joel
My Premier Elements Project settings are:
Editing Mode: DSLR
Timebase: 23.976frames/sec
Video:
Framesize: 1920 x 1080
Pixel Aspect Ratio: Square Pixels (1.0)
Fields: No Fields (Progressive Scan)
Display Format: 24fps Timecode
Audio:
Sampe Rate: 48000 Hz
Output from MediaInfo
General
Complete name                            : Z:\NikonVideo\MomsStory\JDB_20140702_6537.MOV
Format                                   : MPEG-4
Format profile                           : QuickTime
Codec ID                                 : qt
File size                                : 1.46 GiB
Duration                                 : 10mn 32s
Overall bit rate                         : 19.8 Mbps
Encoded date                             : UTC 2014-07-02 18:22:46
Tagged date                              : UTC 2014-07-15 03:24:05
NCDT                                     : NCTG
Video
ID                                       : 1
Format                                   : AVC
Format/Info                              : Advanced Video Codec
Format profile                           : [email protected]
Format settings, CABAC                   : Yes
Format settings, ReFrames                : 2 frames
Codec ID                                 : avc1
Codec ID/Info                            : Advanced Video Coding
Duration                                 : 10mn 32s
Bit rate                                 : 18.3 Mbps
Width                                    : 1 920 pixels
Height                                   : 1 080 pixels
Display aspect ratio                     : 16:9
Frame rate mode                          : Constant
Frame rate                               : 23.976 fps
Color space                              : YUV
Chroma subsampling                       : 4:2:0
Bit depth                                : 8 bits
Scan type                                : Progressive
Bits/(Pixel*Frame)                       : 0.368
Stream size                              : 1.35 GiB (92%)
Language                                 : English
Encoded date                             : UTC 2014-07-02 18:22:46
Tagged date                              : UTC 2014-07-02 18:22:46
Transfer characteristics                 : BT.470 System M
Matrix coefficients                      : BT.601
Audio
ID                                       : 2
Format                                   : PCM
Format settings, Endianness              : Little
Format settings, Sign                    : Signed
Codec ID                                 : sowt
Duration                                 : 10mn 32s
Bit rate mode                            : Constant
Bit rate                                 : 1 536 Kbps
Channel(s)                               : 2 channels
Channel positions                        : Front: L R
Sampling rate                            : 48.0 KHz
Bit depth                                : 16 bits
Stream size                              : 116 MiB (8%)
Language                                 : English
Encoded date                             : UTC 2014-07-02 18:22:46
Tagged date                              : UTC 2014-07-02 18:22:46

Any movie I play either in my library or thru my ipod has the audio choppy and not match the video windows 8

I am so ****** off! I have been trying to resolve this for 2 months now with NO help from Apple. I can play a movie fine in quicktime but when I try to play it in itunes the audio is choppy and does not match the video. The setting seem to be the same. It all worked fine up until a quicktime update 2+ months ago.

I hope that this helps your situation. https://discussions.apple.com/message/23344208#23344208 You can try adjusting your Itunes playback settings for the audio to match your computer's audio settings. I posted in that thread about my positive results. Good luck.

After effects CC export to premiere pro CC: audio doesn't match

Hello!
I am making an animation serie for Belgian TV. They need me to export only my audio from premiere (I make the animations in after effects).
They need OMF format.
When I export from after effects CC > Premiere pro project (only to export my audio to OMF from here) the audio doesn't match.
Adobe media encoder doesn' support OMF unfortunately.
Example; if I stretch the audio time in after effects, premiere doesn't.
I am really stressing out and any help would be very welcome
Thank you!
Ellen

Hello Jim
Thanks for the reply!
When I import my after effects composition into premiere, it is perfectly visible and the audio is correct.
But now it is suddenly impossible to select > export > OMF
Do you know why this is?
Thanks!

CS5 The selected file cannot be linked because its type (audio) does not match the original file's t

Greetings,
I have been working on a very large project using CS5 on my desktop computer. Now I am on the road and bought a laptop so that I can continue to work. I placed all of my assets on a back-up external 2tb drive (which I was able to open without incident on my desktop). I installed CS5 on my new laptop and now when I try to open the project I get the following message "The selected file cannot be linked because its type (audio) does not match the original file's type (audio and video)". This message appears before I indicate the path to any of the assets. Then, when I do indicate the path to each asset, I get the same message for individual files.
Any advice is appreciated.
Thanks,
Jeremy

I had this problem and have found a solution / workaround: my issue was when trying to open a cs5 project that had been collected on mac and then transfered to pc, my footage was all png image sequences but this will hopefully work in other situations...
Open the project and cancel the first dialogue box that pops up where you get the "file cannot be linked" error when trying to reconnect footage. The project will open and then in the project panel, right click on any footage that needs reconnected and choose "Replace footage..." this will open a dialog that will allow you to select the file that gave you the error in the first place without any issues. Any sequences with that footage will now work and everything show be all good.
You may experience "Offline material is present in this export and will be encoded using the offline media graphic" on first export but apparently you can just ingore that, but i guess it's woth testing a few short sections before commiting to a huge render...
This workaround isn't perfect as i had about 50 pieces of footage i had to relink via this method one by one but at least it saved redoing the edit which was critical for my project...
good luck!

After export audio does not match w/ video. ?

I exported my movie from FCE, and the audio is off. It does not match the video, i see lips move but not w/ the sound. Can an help? -Thanks!

Can you provide some specific info or steps you take?
Al

Error: The decapsulated inner packet doesn't match the negotiated policy in the SA

I upgraded my ASA from 8.2(1) to 8.4(3) as I wanted to try to get Android devices to properly connect via VPN.
After some effort, I was able to get the Android devices to connect via VPN. However, my syslog server has a number of errors recorded that look this this:
%ASA-4-402116: IPSEC: Received an ESP packet (SPI= 0x1E76EFA6, sequence number= 0x1F0) from x.x.x.x (user= testuser) to y.y.y.y. The decapsulated inner packet doesn't match the negotiated policy in the SA. The packet specifies its destination as z.z.z.z, its source as a.a.a.a, and its protocol as tcp. The SA specifies its local proxy as y.y.y.y/255.255.255.255/udp/42246 and its remote_proxy as x.x.x.x/255.255.255.255/udp/0.
Digging further, it seems this error might be due to a NAT issues with the VPN connections. VPN previously worked with Cisco's VPN client on Windows, though I did not test to see if that is no longer working. However, I made no changes in the config, except for those related to additions needed to support L2TP. With the below config, Android clients can connect to the ASA and access the internal network, but they cannot connect to external addresses. I'm at a loss.
The addresses used in the config: 192.168.1.0/24 are on the internal LAN and 192.168.3.0/24 are addresses assigned to VPN clients.
I noted in the config this line:
access-list inside_nat0_outbound extended permit ip any 192.168.3.0 255.255.255.0
The access list is not referenced anywhere, though it was referenced in the 8.2(1) config like this:
nat (inside) 0 access-list inside_nat0_outbound
I'm not sure what else changed, but I've looked over the config and I just cannot see what the issue might be. I'm hoping somebody might be able to point out my error.
Here's the config file (at least the parts that might be of interest):
: Saved
ASA Version 8.4(3)
interface Vlan1
nameif inside
security-level 100
ip address 192.168.1.1 255.255.255.0
interface Vlan2
nameif outside
security-level 0
ip address dhcp setroute
boot system disk0:/asa843-k8.bin
object network obj-192.168.3.0
subnet 192.168.3.0 255.255.255.0
object network obj_any
subnet 0.0.0.0 0.0.0.0
access-list outside_access_in extended permit icmp any interface outside time-exceeded
access-list outside_access_in extended permit icmp any interface outside echo-reply
access-list outside_access_in extended permit icmp any interface outside unreachable
access-list outside_mpc extended permit ip any interface outside
access-list inside_mpc extended permit ip 192.168.1.0 255.255.255.0 any
access-list testVPN_splitTunnelAcl extended permit ip 192.168.1.0 255.255.255.0 any
access-list inside_nat0_outbound extended permit ip any 192.168.3.0 255.255.255.0
ip local pool VPN-Pool-1 192.168.3.1-192.168.3.254 mask 255.255.255.0
ip verify reverse-path interface outside
nat (inside,any) source static any any destination static obj-192.168.3.0 obj-192.168.3.0 no-proxy-arp
object network obj-192.168.3.0
nat (outside,outside) dynamic interface
object network obj_any
nat (inside,outside) dynamic interface
access-group outside_access_in in interface outside
crypto ipsec ikev1 transform-set ESP-AES-256-SHA esp-aes-256 esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-DES-SHA esp-des esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-3DES-SHA esp-3des esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-DES-MD5 esp-des esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-3DES-MD5 esp-3des esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-AES-128-SHA esp-aes esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-AES-128-MD5 esp-aes esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-AES-128-SHA-TRANSP esp-aes esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-AES-128-SHA-TRANSP mode transport
crypto ipsec ikev1 transform-set ESP-3DES-SHA-TRANSP esp-des esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-3DES-SHA-TRANSP mode transport
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 10 set ikev1 transform-set ESP-AES-128-SHA-TRANSP ESP-3DES-SHA-TRANSP
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set pfs
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set ikev1 transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA ESP-3DES-MD5 ESP-DES-SHA ESP-DES-MD5
crypto map outside_map 65535 ipsec-isakmp dynamic SYSTEM_DEFAULT_CRYPTO_MAP
crypto map outside_map interface outside
crypto ikev1 enable outside
crypto ikev1 policy 5
authentication pre-share
encryption aes
hash sha
group 2
lifetime 86400
crypto ikev1 policy 10
authentication pre-share
encryption aes-256
hash sha
group 2
lifetime 86400
group-policy testVPN internal
group-policy testVPN attributes
wins-server value 192.168.1.8
dns-server value 192.168.1.8 192.168.1.4
vpn-idle-timeout none
vpn-tunnel-protocol ikev1
split-tunnel-policy tunnelspecified
split-tunnel-network-list value testVPN_splitTunnelAcl
default-domain value test.us
group-policy testVPNnsl2tp internal
group-policy testVPNnsl2tp attributes
wins-server value 192.168.1.8
dns-server value 192.168.1.8 192.168.1.4
vpn-idle-timeout none
vpn-tunnel-protocol l2tp-ipsec
group-policy testVPNns internal
group-policy testVPNns attributes
wins-server value 192.168.1.8
dns-server value 192.168.1.8 192.168.1.4
vpn-idle-timeout none
vpn-tunnel-protocol ikev1
username testuser password PASSWORD encrypted privilege 15
username testuser2 password PASSWORD nt-encrypted privilege 15
tunnel-group DefaultRAGroup general-attributes
address-pool VPN-Pool-1
default-group-policy testVPNnsl2tp
tunnel-group DefaultRAGroup ipsec-attributes
ikev1 pre-shared-key *****
tunnel-group DefaultRAGroup ppp-attributes
authentication ms-chap-v2
tunnel-group testVPN type remote-access
tunnel-group testVPN general-attributes
address-pool VPN-Pool-1
default-group-policy testVPN
tunnel-group testVPN ipsec-attributes
ikev1 pre-shared-key *****
tunnel-group testVPNns type remote-access
tunnel-group testVPNns general-attributes
address-pool VPN-Pool-1
default-group-policy testVPNns
tunnel-group testVPNns ipsec-attributes
ikev1 pre-shared-key *****
tunnel-group testVPNnsl2tp type remote-access
tunnel-group testVPNnsl2tp general-attributes
address-pool VPN-Pool-1
default-group-policy testVPNnsl2tp
tunnel-group testVPNnsl2tp ipsec-attributes
ikev1 pre-shared-key *****
tunnel-group testVPNnsl2tp ppp-attributes
authentication ms-chap-v2
One last question: in order to get the connection from Android to work, I was forced to use "tunnel-group DefaultRAGroup". Is that actually a limitation, or did I make an error that forced that requirement? I wanted to use "tunnel-group testVPNnsl2tp".
Thanks!

Chris,
This is still a bit off the mark. I think I might be confusing the issue by including some of the VPN configuration that I had previously installed and working (e.g., two other VPN tunnel groups with split tunneling on one of them). Let's just remove that stuff from consideration. I actually tested the current configs just to see if they are working since the upgrade. testVPN is working with the split tunneling, but testVPNns (no-split tunneling) does not allow external access. I guess there is a NAT config issue there, too, but not sure what it is, yet. I've not investigated that closely.
I want to solve one problem at a time, though I understand there are some interdependencies.
What I'd like to focus on right now is just the L2TP VPN connection.
From what I've been able to understand from the documentation, what I need are these lines:
crypto ipsec ikev1 transform-set ESP-AES-128-SHA-TRANSP esp-aes esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-AES-128-SHA-TRANSP mode transport
crypto ipsec ikev1 transform-set ESP-3DES-SHA-TRANSP esp-des esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-3DES-SHA-TRANSP mode transport
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 10 set ikev1 transform-set ESP-AES-128-SHA-TRANSP ESP-3DES-SHA-TRANSP
crypto map outside_map 65535 ipsec-isakmp dynamic SYSTEM_DEFAULT_CRYPTO_MAP
crypto map outside_map interface outside
crypto ikev1 enable outside
group-policy testVPNnsl2tp internal
group-policy testVPNnsl2tp attributes
wins-server value 192.168.1.8
dns-server value 192.168.1.8 192.168.1.4
vpn-idle-timeout none
vpn-tunnel-protocol l2tp-ipsec
tunnel-group DefaultRAGroup general-attributes
address-pool VPN-Pool-1
default-group-policy testVPNnsl2tp
tunnel-group DefaultRAGroup ipsec-attributes
ikev1 pre-shared-key P74bmqL6rT40bl5
tunnel-group DefaultRAGroup ppp-attributes
authentication ms-chap-v2
crypto ikev1 policy 5
authentication pre-share
encryption aes
hash sha
group 2
lifetime 86400
I still want to assign the IP addresses to VPN clients out of 192.168.3.0/24.
The tricky part is understanding exactly what NAT rules to insert and to avoid that error message I'm getting relatred to the encapsulated packets. I tried to introduce the commands you had, but it's missing stuff that I would need for L2TP/IPSec (e.g., "mode transport"). I also don't think I want "pfs group5". The above config "works" in that I get connected -- all negotiation is done. It's just that packets from the VPN client are not able to go out to the Internet and I'm seeing that encapsulation error messages when I try to send a packet.
Paul

Itunes doesn't play the video anymore

Help! ITunes doesn't play the video clips anymore just the sound works.
I've restarted, quit the other applications but no result.
What can I do ?
Thank you for your suggestions.
ITunes 8.1
QuickTime 7.6
Mac OS 10.5.6
Mac Pro 2x3 GHz
RAM 8 Go

If you are playing through remote speakers, iTunes 8.1 will not play the video. Previous versions would play fine using only the computer's speakers, but 8.1 requires the remote airtunes speakers be deselected.

I have been buying apps for a long time without a problem using my credit card on file. All of a sudden itunes is not recognizing my card which is in good standing. All the info is correct but itunes/apple says it doesn't match the bank info. Any ideas

I have been buying apps for a long time without a problem using my credit card on file. All of a sudden itunes is not recognizing my card which is in good standing. All the info is correct but itunes/apple says it doesn't match the bank info. Any ideas?

Answered in your Other post on this Topic...
https://discussions.apple.com/message/24053626#24053626

Iphoto'09 doesn't import the video made by Kodak DX6490 since update 10.6

Iphoto'09 doesn't import the video i made on my Kodak DX6490 since i've installed mac os 10.6 with an update from 10.5.8
The videos i made are .mov and with iphoto'09 and Leopard 10.5.8, it was possible to import them.
Have you seen this problem ? Any idea to correct it ?

TD,
My comment regarding this problem was only meant to support your solution (test), not disparage it.
I was briefly trying to explain that I believe (anecdotally) Snow Leopard is not functioning correctly in regard to movie imports using normal import procedures.
At first I assumed it was a problem with iPhoto 06, and ordered a copy of iLife 09 for my daughter. Then I found this thread and IMHO it confirmed my workaround (kludge) solution. I would wager that she will have the same problem with iPhoto 09.
It should "just work."
I will report the outcome.
Cheers
Ferd II

3201: The publisher display name FooBar, specified in the package doesn't match the publisher name, FooBar

I've updated a WP 8.0 application to WP 8.1 Silverlight. When I try to deploy a demo application I get the following error;
3201: The publisher display name, FooBar, specified in the package doesn’t match the publisher name,
FooBar, that’s associated with the developer account.
I've seen several cases with people encounter this issue and then solved by modifying WPAppManifest or the Packages file. My problem is that the
display name and publisher name is exactly the same. Both in the application xml files and in the error message displayed by windows phone store.
Any suggestions?

There is no requirement that source code files are in the correct directory structure. If you want javac to be able to automatically compile dependent files, then the source code must be in an appropriate structure and find-able from the classpath.
Also, when you use the -d option, javac will create an appropriate directory relative to the directory specified in the -d option. That's how it is supposed to work.
So it is working as designed and specified.

The pt 3 tutorial code doesn't match the pt 2 tutorial code. Nowhere to insert head in pt 2 code.

At the end of the part 2 tutorial, this was the code:
@charset "utf-8";
/* CSS Document */
#container {
width: 968px;
background: #FFF;
margin: 0 auto;
padding-left: 10px;
padding-right: 10px;
overflow: hidden;
}#main_image {
background-image: url(images/main.jpg);
background-repeat: no-repeat;
#container #main_image {
height: 376px;
width: 968px;
#left_column, #center_column, #right_column {
width: 316px;
float: left;
#center_column, #right_column {
margin-left: 10px;
The part 3 tutorial instructed this:
Copy the <script> tags from the Edge Web Fonts site, and paste them into the <head> section of index.html in Dreamweaver just above the <link> that attaches the style sheet like this:
<head>
<meta charset="utf-8">
<title>Check Magazine</title>
<script src="http://use.edgefonts.net/sarina.js"></script>
<link href="styles/check_cs6.css" rel="stylesheet" type="text/css">
</head>
As you can see from the code at the end of part two (listed at the top), there is no reference to <head> anywhere in the code; therefore, I am uncertain as to where to insert these code instructions.

I assume that the embedded tags are in the index document, not the styles type document?   I appreciate the information, but I don't see how it relates to my question. Maybe your answer was just over my head? My original question was: If the instructions say this:
Copy the paste them into the section of index.html in
Dreamweaver just above the that attaches the style
sheet like this:
and there the word does not appear anywhere on the index file that I can see it (whether it's embedded or otherwise), where do I insert the code?
Date: Fri, 8 Feb 2013 10:29:29 -0800
From: [email protected]
To: [email protected]
Subject: The pt 3 tutorial code doesn't match the pt 2 tutorial code. Nowhere to insert <head> in pt 2 code.
    Re: The pt 3 tutorial code doesn't match the pt 2 tutorial code. Nowhere to insert in pt 2 code.
    created by Nancy O. in Dreamweaver - View the full discussion
The pair of and tags are an integral part of any HTML document. When you create a new page in DW, it automatically creates the core HTML tags for you, so in that regard, there's nothing for you to add except content and styles. Embedded CSS styles are inserted inside the document's tags like so:       body      #LeftSideBar       #RightSideBar      #MiddleContent
External CSS is a separate physical file to which all your HTML pages are linked. Similar to above, links to external style sheets go inside the tags like this:
HTML & CSS Tutorials - http://www.html.net/http://w3schools.com/ Nancy O.
     Please note that the Adobe Forums do not accept email attachments. If you want to embed a screen image in your message please visit the thread in the forum to embed the image at http://forums.adobe.com/message/5058678#5058678
     Replies to this message go to everyone subscribed to this thread, not directly to the person who posted the message. To post a reply, either reply to this email or visit the message page: http://forums.adobe.com/message/5058678#5058678
     To unsubscribe from this thread, please visit the message page at http://forums.adobe.com/message/5058678#5058678. In the Actions box on the right, click the Stop Email Notifications link.
     Start a new discussion in Dreamweaver by email or at Adobe Community
For more information about maintaining your forum email notifications please go to http://forums.adobe.com/message/2936746#2936746.

When I import my files only the audio plays back not the video. If I export the sequence its there?

When I import my files only the audio plays back not the video. If I export the sequence its there?
I am new to Premiere having just downloaded the 30 day trial yesterday, I jumped straight in and imported all of my files from my video camera however in Premiere only the audio plays back with the displays just showing a black space.
Out of curiosity I dragged three or four shots into the sequence editor and then exported them and played this through VLC and the video was there?
As I said I am completely new to Premiere having only spent around 3 or 4 hours with it in the past, I read a few forum threads around similar issues but couldn't find any solutions and as I am trying to edit together a short film for a college project due in soon I need to try and find a way to fix this A.S.A.P
Any help would be appreciated and if theres any more info I can provide please let me know.
Thanks
Drew

Being new, I'm sure you don't know about the NEW ITEM process, so click/read about that at this link
CS5-thru-CC PPro/Encore tutorial list http://forums.adobe.com/thread/1448923
Also, More information needed for someone to help... please click below and provide the requested information
-PPro Information FAQ http://forums.adobe.com/message/4200840
What is your exact brand/model graphics adapter (ATI or nVidia or ???)
What is your exact graphics adapter driver version?
Have you gone to the vendor web site to check for a newer driver?
For Windows, do NOT rely on Windows Update to have current driver information
-you need to go direct to the vendor web site and check updates for yourself
ATI Driver Autodetect http://support.amd.com/en-us/download/auto-detect-tool
nVidia Driver Downloads http://www.nvidia.com/Download/index.aspx?lang=en-us
Exactly what are you editing?
Codec & Format information, with 2 links inside for you to read http://forums.adobe.com/thread/1270588
Report back with the codec details of your file, use the programs below... A screen shot works well to SHOW people what you are doing
http://forums.adobe.com/thread/592070?tstart=30 for screen shot instructions
Free programs to get file information for PC/Mac http://mediaarea.net/en/MediaInfo/Download

How to make the audio track independent from the video track?

Can someone remind me how to make the audio track independent from the video track? My memory just went blank. Must be the age.
Thanks

Hi -
Select the clip in the timeline.
Type Command + L or go to the menu Modify > Link to toggle it off.
MtD

Audio doesn't match the video ... why

Similar Messages

Maybe you are looking for