AUDIO DRIVER of compaq presario f761us for windows XP

where can I down load the audio driver for windows XP.
my notebook is compaq presario f761us.
ps: there is no audio driver in HP's web sit as below,
http://h10025.www1.hp.com/ewfrf/wc/softwareCategory?os=228&lc=en&cc=au&dlc=en&sw_lang=&product=36787...
Thank you.

Hi:
I looked around and all I could find were audio drivers for Windows Vista.
If you can connect your notebook to the internet, I recommend you download and run this free tool called Device Doctor. It has helped me out lots of times.
It will scan you computer and then find the drivers from a database somewhere in cyberspace.
Hopefully it will point you to the XP audio driver. I don't recommend you update any drivers that are working but for ones that you can't find, you have nothing to lose. Again, your notebook must be connected to the internet for this to work.
Link to the Device Doctor Portable is below:
http://www.devicedoctor.com/device-doctor-portable.php
Paul

Similar Messages

Can you send me the links to instal the drivers of compaq presario c700 for window xp

sir send me the link and details to download these drivers

Hi:
HP does not have an XP download page for the c700.
Please read the XP downgrade guide at the link below for instructions and links to the XP drivers you need for your notebook.
http://h30434.www3.hp.com/t5/Notebook-Operating-systems-and/General-XP-Downgrade-Guide-for-HP-Laptop...
The instructions for the c700 can be found in the section labeled 2. Moderate Models.
Paul

Hp compaq nc4200 drivers for windows 8 iam very sad because am not found thise drivers

hp compaq nc4200 drivers for windows 8 iam very sad because am not found thise drivers in any sits please anser me quq
thanx

Hi,
Besides britishdhez's suggestion, we also try to get your apps and devices working in
Windows 8.1 in compatibility mode:
Get your apps and devices working in Windows 8.1
http://windows.microsoft.com/en-IN/windows-8/get-apps-devices-working
Karen Hu
TechNet Community Support

WiFi & Bluetooth drivers not available for HP Compaq 15-s008Tu for Windows 7-64 bit

Hi, I am not able to find the drivers for WifI & Bluetooth at the support portal for HP Compaq 15-s008Tu for Windows 7(64 bit).Please help me with these drivers. Thanks a ton in advance!!

Hi: Wireless: http://h10025.www1.hp.com/ewfrf/wc/softwareDownloadIndex?softwareitem=ob-131223-1&cc=us&dlc=en&lc=en... Bluetooth: http://h10025.www1.hp.com/ewfrf/wc/softwareDownloadIndex?softwareitem=ob-137961-1&cc=us&dlc=en&lc=en...

I need help finding the driver for my ethernet.it is a compaq presario sr1403wm with windows xp.

compaq presario sr1403wm
windows xp
my computer dropped the driver for the ethernet card and am unable to do a system restore.

HP Spring 2005 Original Network Adapter Driver Collection
or
SiS900 LAN Driver v1.19
Frank
{------------ Please click the "White Kudos" Thumbs Up to say THANKS for helping.
Please click the "Accept As Solution" on my post, if my assistance has solved your issue. ------------V
This is a user supported forum. I am a volunteer and I don't work for HP.
HP 15t-j100 (on loan from HP)
HP 13 Split x2 (on loan from HP)
HP Slate8 Pro (on loan from HP)
HP a1632x - Windows 7, 4GB RAM, AMD Radeon HD 6450
HP p6130y - Windows 7, 8GB RAM, AMD Radeon HD 6450
HP p6320y - Windows 7, 8GB RAM, NVIDIA GT 240
HP p7-1026 - Windows 7, 6GB RAM, AMD Radeon HD 6450
HP p6787c - Windows 7, 8GB RAM, NVIDIA GT 240

How to install audio driver on a presario sr1907cl

I am having one hell of a time trying to install the audio driver on a compaq presario sr1907cl. When I try to install sp26731, it said I have to install UAA Audio Buss Driver from Microsoft, so when I tryed to install it, I got a window that said my os is newer than the driver. Seems like I'm just spinning my wheels. Don't know what to do to get sound on this thing. Any help would be greatly appriciated. I've never seen anything like this just to install a sound driver, but I'm sure this has happened to lots of others.
Thank You Much,
[email protected]
This question was solved.
View Solution.

Hi:
You probably should install the latest XP nForce chipset driver for your model first and reboot.
http://www.nvidia.com/download/driverResults.aspx/9701/en-us
Then see if the latest Realtek driver works.
If you installed XP SP3, you shouldn't need the msuaa driver.
Accept the agreement, download and install the 4th item on the list (first one in green).
http://www.realtek.com.tw/downloads/downloadsView.aspx?Langid=1&PNid=24&PFid=24&Level=4&Conn=3&DownT...

No audio on my Compaq Presario F750EL

Hi everyone, I've some troubles with my audio system.
This morning I was on Youtube watching a video; I closed the page for a while, then I tried to watch again the same video and I didn't get any sound (I tried even with headphones, but I can't still hear a thing).
On my speaker icon there's a red cross, if I put my cursor on it, it says "No AudioDevice Installed".
So, I went to my local support site (I'm Italian) and tried to fix the problem by going on Start>services.msc>Windows Audio>right click, but then I couldn't click on the Start button as I was supposed to.
I then tried to download the driver for my notebook. At first, I let HP check for me if I needed any but then, as it said I didn't, I downloaded myself the only audio driver possible for my version (I checked and put the right operative system).
However, when I try to install the driver, it runs properly until it says that the driver cannot be installed because it can't find the device for this driver.
N.B.: I haven't uninstalled my previous driver and I haven't downloaded any upgrade lately, my audio just switched off for no reason apparently.
Honestly I'm not that good with computers so, please, explain clearly; I also hope that I was enough clear and the terms were right as I translated everything at my best.
Thanks a lot in adance for a quicl response!
Best rgds
My computer is a Compaq Presario F750EL
(http://h20000.www2.hp.com/bizsupport/TechSupport/Document.jsp?lang=en&cc=us&objectID=c01366233)
My operative system is Windows Vista 32bit
I downloaded this diriver: Driver Conexant HD-Audio SmartAudio 221
If you need more info tell me.

i did the restore, too, and it didn't work. that's what baffled me! imagine restoring to factory default and the audio still does not work? i must admit that i did download one of the updates and got the audio working. it was temporary because as the Windows Vista updates were being applied, at one point I lost audio again.
i did a bit more research last night and found an interesting post. it requires manually amending some files, so i'm okay to give that a try. as this has been quite the issue to troubleshoot, i will post a solution if I find it. i don't want to settle on this... don't give up!

Compaq Presario CQ60-211dx - Windows XP Sounds Are Low Pitched

I know I'm going to get replies saying to upgrade my OS from Windows XP.
I have a Compaq Presario CQ60-211dx running Windows XP Professional 32 bit. The system sounds are kind of low pitched. Let's say the system audio is at C but my sound is at B flat. It's starting to become kind of annoying, because I don't really like sounds that are off tone. Also whenever I close and open the lid on the laptop, the sounds just don't work, until I restart the laptop. I have Conexant HD Smartaudio 221.
Anyone help?

Hi @darkness12445
Welcome to the HP Support Forums!
I understand that you are having sound quality issues. I am happy to assist. When I looked up your notebook I found that there were no drivers for XP on the support page, which would mean it was not sold configured for XP. So the drivers you are using would not have been customized to be compatible with the other standard devices in this series of notebooks. That may be part of the problem.
But for now...
No sound in Windows - windows.microsoft.com
Fix for Windows XP Poor Sound - eHow.com
Malygris1
I work on behalf of HP
Please click Accept as Solution if you feel my post solved your issue, it will help others find the solution.
Click Kudos Thumbs Up on the right to say “Thanks” for helping!

Dolby Audio driver cannot start after upgrading to Windows 8.1

Hello.
Windows 8 was the worst thing that happened to Windows, but since I bought this G505s laptop with Win8 pre-installed, i had no other choice to go to. Few days after the purchase, Windows 8.1 arrived and I updated 8 to 8.1 hoping to see some improvements. But to my sadness, 8.1 has ruined my expectations, and Lenovo didn't even care to address the user issues in 8.1
Here are my Issues :
OneKey Recovery : Updated to 8.xx.xx.xxxx
The OneKey Recovery app tells that 'Current system cannot create a backup'
I can't have a secure laptop without it creating the Recovery !!
Lenovo, please address this issue and fix the OneKey Recovery Problem !!
Dolby audio app : Doesn't open, and if once it starts, cannot configure the Equalizer !
--- Dr Saketh ---

hi sotim01,
Thanks for posting!
1. Uninstall all components,
Open Device Manager and Uninstall your Conexant audio under Sound and ganing controllers (make sure to place a check under delete driver software for this device)
2. Open Control Panel Uninstall a program and highlight the dolby component and an Uninstall button will appear.
3. Open your C: drive and Delete any folder that says drivers if non then continue with the next step
4. Download this Driver for installation
Conexant Audio Driver
Install it and continue
5. Open Drive C: now and you should have the Drivers folder back.
Open that, Open Connexant Open Dolby Gui, then you should have Dolbyaa for Advanced audio.
Restart your PC and there you go!
Let me know your findings
Cheers!
Did someone help you today? Press the star on the left to thank them with a Kudo!
If you find a post helpful and it answers your question, please mark it as an "Accepted Solution"! This will help the rest of the Community with similar issues identify the verified solution and benefit from it.
Follow @LenovoForums on Twitter!

No Audio on either end Cisco Jabber for Windows over Cisco AnyConnect

Our telephony staff is replacing our aging/unsupported VoIP system with a Cisco system and as the network tech, I'm trying to get Jabber for Windows to work over our AnyConnect VPN client. Jabber to Cisco phone and Jabber to Jabber calls work fine within our LAN.
However, when I take a laptop to a separate internet connection and connect to the network via the VPN, I can't get any audio to pass across the system, in either direction. If I call a phone on our LAN using the Jabber client (via AnyConnect), the phone rings and when I answer it, it's just dead air on both ends. If I reverse the process, calling from the phone to the Jabber client, the same thing, Jabber client rings, but dead air both ways once I answer.
Things I can do from the laptop over the VPN connection:
I'm able to get to the phone's web interface using that same laptop.
I can ping the phone as well. In fact, the VPN profile I'm using has full access to the entire VoIP Vlan including all IP traffic (all ~65,000 ports).
Searching the address book also works fine. I can search for staff and it's pulling directly from our Active Directory environment.
Is there any special settings on the firewall that I need to setup to allow the voice traffic (which I assume is RTP traffic)? I tried to add a service policy for RTP traffic, but that didn't seem to work...unless I built it wrong.
Jabber for Windows - 10.6.0
Cisco Anyconnect - 3.1.06079
Cisco 5515-x ASA - 9.2

I was able to resolve this on my own. I thought that SIP traffic needed to be inspected via the global inspection policy in order for it to pass through the firewall. I ran into the same issue with ICMP traffic from an Anyconnect client to LAN devices. I had to enable ICMP in that policy for us to be able to ping LAN devices over the VPN tunnel. So when I saw that SIP was already being inspected by this policy, I moved on looking for other solutions. Then I stumbled deep within a Google search (almost hit the end of the Internet doing so) where someone mentioned that SIP shouldn’t be inspected by that policy. So I unchecked it and bam! Voice is now working over the anyconnect client to phones on the LAN.

Doly Audio driver cannot start after upgrading to Windows 8.1

Upgrade to Windows 8.1 went flawlessly, but when I restart I get this message:
I can't find any reference to Dolby Theater or Audio in any app or Device management.
I can't find any drivers for Windows 8 64 bit on the Lenovo site either.
Can anyone help with this?
Solved!
Go to Solution.

There is a possible solution in the following thread;
http://forums.lenovo.com/t5/General-Discussion/Dolby-Home-Theater-v4-for-most-Lenovo-Laptops/m-p/126...
Andy ______________________________________
Please remember to come back and mark the post that you feel solved your question as the solution, it earns the member + points
Did you find a post helpfull? You can thank the member by clicking on the star to the left awarding them Kudos Please add your type, model number and OS to your signature, it helps to help you. Forum Search Option T430 2347-G7U W8 x64, Yoga 10 HD+, Tablet 1838-2BG, T61p 6460-67G W7 x64, T43p 2668-G2G XP, T23 2647-9LG XP, plus a few more. FYI Unsolicited Personal Messages will be ignored.
Deutsche Community Comunidad en Español English Community Русскоязычное Сообщество
PepperonI blog

G480 - Dolby Audio driver cannot start after upgrading to Windows 8.1

I upgraded today to 8.1 and now when I start my computer I get a message box telling me <re-install Dolby advanced audio driver>. I found the Dolby program in my control panel, programs and features, and there is no un-installer or, seemingly a way to re-install the driver. I want fix this problem / don't want this box popping up at every boot, what do I do? Thank You.
Tim

hi sotim01,
Thanks for posting!
1. Uninstall all components,
Open Device Manager and Uninstall your Conexant audio under Sound and ganing controllers (make sure to place a check under delete driver software for this device)
2. Open Control Panel Uninstall a program and highlight the dolby component and an Uninstall button will appear.
3. Open your C: drive and Delete any folder that says drivers if non then continue with the next step
4. Download this Driver for installation
Conexant Audio Driver
Install it and continue
5. Open Drive C: now and you should have the Drivers folder back.
Open that, Open Connexant Open Dolby Gui, then you should have Dolbyaa for Advanced audio.
Restart your PC and there you go!
Let me know your findings
Cheers!
Did someone help you today? Press the star on the left to thank them with a Kudo!
If you find a post helpful and it answers your question, please mark it as an "Accepted Solution"! This will help the rest of the Community with similar issues identify the verified solution and benefit from it.
Follow @LenovoForums on Twitter!

Hard drive networked through Time Capsule for Windows and Mac

My previous setup was using an old Dell laptop with Windows XP to network share both my Samsung laser printer and my Seagate GoFlex 2 tb drive formated to NTFS, and all Windows 7, Windows 8, and OS X 10.6+ machines in the house were successfully able to connect to both. My wife replaced her old Macbook Pro she got in 2008 and decided to get a Time Capsule as well to backup her iMac and new Macbook Air. I decided to take advantage of the "features" of the Time Capsule, and hubbed the single port, just as I had done with the old Dell. After installing Bonjour on the Windows 7 machines I was able to share the printer just fine, however I'm still unable to share the drive for some reason.
The Airport utility on both the Macs and Win 7 machines see the hard drive in utilities, the box in Airport for file sharing is checked, guest access turned off, secure disk sharing with device password, and workgroup matches my workgroup. However the hard drive still doesn't appear. I tried formatting it to FAT32 based on some older forums posted in 2008-2009 range, but then realized the hard drive is too large for that, and I'm not looking to have a bunch of smaller partitions. I tried exFAT, but that failed too. Now I'm back to NTFS, but still with the issue that none of the machines recognize hard drive via the Explorer/Finder.
The Time Capsule is functioning as a backup with Time Machine for her Mac's, but I'm looking to use the external drive connected more as a media center storage and storing selected individual files (think networked thumb drive/USB stick) from my machines.

Put the seagate drive onto the Mac and format it Mac OS extended journaled. (HFS+ for short) and you will also need to change the partition over to GUID from MBR.
TC has very limited formats it can recognise.. FAT32 and HFS+ (well FAT16 but that doesn't count). exfat no, ntfs no, Really with FAT32 being hopeless.. you have one choice .. HFS+.
The Windows machines can handle files to the drive just fine.. because it is a network drive.. it is offered to the network as SMB protocol.. in windows it will look like NT server. The precise format of the drive is irrelevant and is handled by the firmware of the TC.
But do reset the partition scheme to GUID.. not MBR.
http://support.apple.com/kb/ph5845
You can even put 2 or more partitions on it.. but only one is fine.

Search for a driver: Ricoh Multi Card Reader for Windows 8 - for my T61 (6463) -

Hi!
I`m searching for a Windows 8-Driver for my T61 (6463).
I have a Ricoh Multi Card Reader inside and I can`t find a driver for this one.
Can anybody help me?
Thank you,
Heiko
Solved!
Go to Solution.

Hello,
Try downloading the following driver:
Name: Ricoh Multi Card Reader Driver for Windows Vista, XP
Version: 3.54.02
Date: 06 Mar 2008
URL: http://support.lenovo.com/en_US/detail.page?LegacyDocID=migr-68053
The drivers will extract to a directory named "C:\DRIVERS\WIN\4IN1\", if I recall correctly. Once extracted, run Device Manager (filename: DEVMGMT.MSC), go to the entry where the unrecognized card reader is located, and perform an update, using the "Have Disk" option and pointing it to the directory in which the drivers were extracted.
I do not recall if a reboot is required, but in any case I would recommend doing one, at which point you should then be able to see the card reader from Windows 8.
Regards,
Aryeh Goretsky
I am a volunteer and neither a Lenovo nor a Microsoft employee. • Dexter is a good dog • Dexter je dobrý pes
S230u (3347-4HU) • X220 (4286-CTO) • W510 (4318-CTO) • W530 (2441-4R3) • X100e (3508-CTO) • X120e (0596-CTO) • T61p (6459-CTO) • T43p (2678-H7U) • T42 (2378-R4U) • T23 (2648-LU7)
Deutsche Community Comunidad en Español Русскоязычное Сообщество

Graphic card driver update doesn't work for Windows 8.1 upgrade (Ideapad Y500)

I upgraded my windows 8 to Windows 8.1 today and it probably is a huge mistake. After the upgrade my Ideapad Y500 started to look weird (Firefox stopped working). I searched around for solution and was told that I probably need to upgrade the driver to my graphic card. So I went to the driver download page and downloaded the NVIDIA GeForce GT750M Second VGA BIOS Update for Windows 8.1
I followed the instruction to run the "Winflash_Yx00s.bat" file, but after I seleted "yes" to let it modify the system, there is a very fast flashing a little black window (too fast for me to see what it is), and nothing happens afterwards. I checked to make sure that nothing is running in the background. After waited for half an hour I tried to restart the computer and still nothing happens. The display still looks weird.
Please help me!

when I read posts like yours I often do the test myself
so I went into skype both metro and desktop skype and to my horror like you I did not have the option only my logitech webcam was an option
I went into devices and see that ht had FaceTimeHD camera (Built-in) as malfunctioning not working devices there
I went to my bootcamp driver zip and ran the apple AppleCamera64.exe
but little did it help then I googled it
https://www.google.dk/search?q=bootcamp+facetime+hd+camera+driver&oq=bootcamp+fa cetime+hd+camera+&aqs=chrome.1.69i57j0.9286j0j8&sourceid=chrome&es_sm=93&ie=UTF- 8
came across this post at ms
http://answers.microsoft.com/en-us/windows/forum/windows_8-hardware/facetime-hd- camera/0ef43e8a-45bc-4797-99f7-c57848b9f2bb
did the uninstall of both of the unknown devices as suggested and ran a scan for new hardware and bam!
the camera was back in action
suppose looking like a gobling shark made it so I never noticed that win8.1 had broken my facetime cam before you brought it up

AUDIO DRIVER of compaq presario f761us for windows XP

Similar Messages

Maybe you are looking for